This paper presents a low cost and portable DOA (Direction Of Arrival) estimation system for surveillance using a modifed beamspace MUSIC (MUltiple Signal Classification) by a quasi-orthogonal multi-beam. This is instead of DFT processing and hardware system consisting of chip-sized phase shifters, a single ADC (Analogue to Digital Converter) and a single TR (TRanceiver) module for an antenna array. In the beamspace MUSIC, generated beampatterns have orthogonal properties. This proposed system cannot make such a beampattern due to the variable range limitation of phase shifter, then we use the quasi-orthogonal beam obtained by the calculation of correlation coefficient for beampattern. We demonstrate the proposed system using 4-element microstrip array antenna and chip-sized phase shifters. The DOA experiment in anechoic chamber confirms the proposed system performance.

The crosstalk phenomenon, wich occurs between transmission lines, is caused by electromagnetic fields of currents flowing through the lines. Crosstalk between two bent lines is studied by using a set of solutions of modified telegrapher's equations. By expressing electromagnetic fields in terms of voltages and currents in the line ends, the resultant network function in the form of an ABCD matrix is obtained. Electromagnetic fields caused by currents flowing in risers at transmission line ends are taken into account in addition to those fields in line sections. The validity of the proposed approach was confirmed by comparing experimental results with computed results and those simulated by a commercial electromagnetic solver for some bent-line models.

This paper deals with the scattering of a TM plane wave from a perfectly conductive sinusoidal surface with finite extent. For comparison, however, we briefly discuss the diffraction by the sinusoidal surface with infinite extent, where we use the concept of the total diffraction cross section per unit surface introduced previously. To solve a case where the sinusoidal corrugation width is much wider than wave length, we propose an undersampling approximation as a new numerical technique. For a small rough case, the total scattering cross section is calculated against the angle of incidence for several different corrugation widths. Then we find remarkable results, which are roughly summarized as follows. When the angle of incidence is apparently different from critical angles and diffraction beams are all scattered into non-grazing directions, the total scattering cross section increases proportional to the corrugation width and hence the total scattering cross section per unit surface (the ratio of the total scattering cross section to the corrugation width) becomes almost constant, which is nearly equal to the total diffraction cross section per unit surface in case of the sinusoidal surface with infinite extent. When the angle of incidence is critical and one of the diffraction beams is scattered into a grazing direction, the total scattering cross section per unit surface strongly depends on the corrugation width and approximately approaches to the total diffraction cross section per unit surface as the corrugation width gets wide.

Using an electro-absorption duplexer (EAD) we presented a transceiver (TRx) module for dual function of both electrical-to-optical (E/O) and optical-to-electrical (E/O) conversion at 60 GHz band. The EAD chip was fabricated by monolithically integrating both a waveguide photodiode (PD) and an electro-absorption modulator (EAM) in association with traveling wave electrodes. We also investigated the issues of RF packaging in which the optoelectronic and electronic amplifier devices were co-packaged in a single housing. The RF impedance matching was accomplished in assistance with a microstrip bandpass filter.

A broadband microstrip-to-waveguide transition is developed in the millimeter-wave band. No additional parts and complicated structures are needed to extend the frequency bandwidth. Only the simple and novel geometrical features are added in the printed pattern on the substrate. The proposed transition operates over a quite broad frequency bandwidth due to its double resonance. The two resonant frequencies are controlled by adjusting dimensions of the structure according to the required bandwidth, the reflection level and the center frequency. Two versions of the transition are designed and reliability is confirmed by experiments in the millimeter-wave band. The design frequency is 76.5 GHz. Bandwidth 12.9 GHz (16.8%) is obtained where the reflection level is lower than -30 dB. In the other design for broadband, the bandwidth for reflection level lower than -20 dB results in 24.9 GHz (32.5%). Furthermore, it is confirmed in the experiment and simulation that the center frequency is controlled from 75.3 GHz to 78.7 GHz by changing the geometry of the printed pattern.

In CDMA cellular systems, the frequency reuse factor equals one. Therefore, the soft-handoff technology with combining macroscopic diversity was introduced to enhance the link performance. In this work, a novel macroscopic diversity combining scheme is proposed to enhance the link performance of the forward-link. The basic concept of this scheme is to integrate error correction coding into the soft-handoff technology. According to the number of soft-handoff channels, the source information is encoded by a convolutional code with a lower code rate. The coded symbols are then equally distributed to all channels from different BSs to the MS, and each channel carries a disjointed set of coded symbols. For this proposed scheme, no extra transmission power or bandwidth is required. The only cost is a slight increase of the encoding and decoding complexity of the convolutional codes. Numerical and simulation results show that a performance gain of 1 dB in bit energy-to-total noise power density ratio can be obtained as compared with the conventional scheme in the same conditions.

A Non-Uniform Discrete Multitone (DMT) transceiver employing an octave spaced quadrature mirror filter (QMF) bank, can be used to overcome the problem of channel noise enhancement in the zero-forcing (ZF) equalization technique. In this letter, performance of the Non-Uniform DMT system is analyzed. A study of the crosstalk between sub-channels due to non-ideal filter banks is also presented. Crosstalk analysis is based upon the bit error rate (BER) performance versus the QMF order in a standadard ADSL channel. Performance comparison of the Non-Uniform DMT transceiver and a conventional DMT system is given, and it is shown that the Non-Uniform DMT transceiver displays slight improvement over the conventional DMT system for the filters of higher order.

Complex thin oxide films with electro-optic (EO) properties are promising for use in advanced optical devices because of their large EO effect. We developed a method of aerosol deposition (AD) for fabricating EO films. The mechanism for AD is based on the solidification by impact of submicron particles onto a substrate. Since particles in AD films preserve their crystalline structure during the formation of film, epitaxial growth is not necessary for exhibiting the EO effect. Highly transparent Pb(Zr, Ti)O3 films, which have acceptable transmittance loss for use as optical devices, were directly deposited on glass substrates by AD. We found the Pb(Zr, Ti)O3 film by AD produced a fairly high EO coefficient (>150 pm/V), approximately 10 times larger than that of LiNbO3. A Fabry-Perot (FP) optical modulator was developed with EO films fabricated by AD. We demonstrated the modulation of optical intensity with an electrical field applied to an EO film made of ferroelectric Pb (Zr, Ti)O3.

Novel dual-band bandpass filter (BPF) with quasi-elliptic function response by using the meander coupled step-impedance resonators (SIRs) is presented. By tuning the appropriate impedance ratio (K) and physical length of SIRs, the BPF has good dual-band performance at 2.4 and 5.2 GHz with high selectivity, due to the transmission zeros appeared in two passband edges. Measured results of the proposed BPF have a good agreement with the electromagnetic (EM) simulated results.

This paper presents novel multi-band equilateral triangular microstrip antennas (ET-MSAs) fed by an L-shaped feeding probe. Two types of the ET-MSA are proposed in this paper; they are ET-MSA with closed folded slots and open folded slots with an embedded bridge. The antenna prototypes presented in this paper assume four folded slots in which a metal strip is inserted to realize a good multi-band performance. In addition, the open folded slots, in which the metal strip inside the folded slot is connected to the ET-MSA by the embedded metal bridge, leads to miniaturize the antenna. The proposed antennas are printed on the top layer of a PTFE substrate while the L-probe is printed on the bottom one. The L-shaped probe is utilized due to its tremendous performance in providing a wideband impedance matching. Five resonant frequencies of the ET-MSAs with closed folded slots and with open folded slots are predicted by the electromagnetic simulator (IE3D) based on the method of moment, respectively. Some parametric studies have been also investigated to meet an appropriate multi-band performance. A broadside radiation pattern and gain of 3.0-7.0 dBi have been confirmed by the measurement for the entire observed frequencies. Measured results agree well with the prediction. Thus, these antenna systems are demonstrated to be useful models for a multi-band planar antenna.

We demonstrate single electron counting on an alkanethiol-protected Au nanodot in a double-barrier tunneling structure by noncontact atomic-force spectroscopy (nc-AFS). The Coulomb step width dependence on the Au nanodot diameter is observed. Evaluation of fractional charge Q0 and contact potential difference by nc-AFS reveals a Vd-independent voltage shift due to Q0.

In situ observation of the adsorption process and reduction behavior of hemoglobin adsorbed on a bare glass surface was studied using slab optical waveguide (SOWG) spectroscopy. The peak position of the absorption band of hemoglobin adsorbed on the glass surface was almost the same as that of hemoglobin in solution. This result agrees with results previously reported by our group. The adsorbed hemoglobin molecules were also reduced by sodium dithionite solution. The adsorbed hemoglobin molecules still maintained their function in this experimental condition.

A novel wideband bandpass filter with improved stopband characteristics is presented in this paper. Dual-mode square ring resonator is used in the proposed filter. New formulas based on the even- and odd-mode analysis are derived to facilitate the design of transmission zeros of the square ring resonator. A short-circuited stub and a piece of aperture-enhanced parallel-coupled lines are introduced to the input and output of the resonator to lower the passband return loss and widen the stopband of the filter significantly. The filter has a 50% fractional bandwidth, is compact in configuration, and shows remarkably improved performance compared with previously reported filters of the same kind. The measured filtering response shows a good agreement with the simulated result.

In situ observations were mainly performed by using slab optical waveguide (SOWG) spectroscopy synchronized with potential step measurements to investigate the time dependent spectral change of the adsorbed heptyl viologen cation radicals (HV+) in thin deposition layer on indium-tin-oxide (ITO) electrodes. Several absorption bands, which indicated a monomer and dimer of HV+ were co-adsorbed on ITO electrode surface with a monolayer or a few layers deposition, were observed in UV-visible region. The time dependent spectra yielded some important molecular information for the adsorption phenomena of HV+ on the electrode surface. All observed absorption bands disappeared completely when the electrode potential of -200 mV vs. Ag/AgCl was applied, which indicated the adsorbed HV+ species were electrochemically reoxidized on the ITO electrode.

This paper overviews the history of a class of varactor tuned bandpass filters. Since the miniaturization as well as the high performance of the tunable bandpass filters is required for the next generation mobile communication systems, the discussion is focused on the various planar type tunable filters including active configurations. Brief design concepts of various tunable filter configurations as well as their characteristics are discussed.

In this paper a new method for the design and optimization of microstrip parallel coupled-line bandpass filters is presented which allows for the specification of frequency bandwidths and arbitrary source and load impedance transformation. The even- and odd-mode theory and the relationships between impedance, transmission and scattering matrices and their properties are used to construct a positive definite error function using the insertion losses at discrete frequencies in the pass, transition and stop bands. The dispersion relations for the coupled line are also taken into account. The minimization of the error function determines the widths, gap spacings and lengths of the coupled-line filter, for the optimum design and realization of filter specifications. The proposed filter design and optimization method is coded by computer programs and the results of simulation, fabrication and testing of sample filters together with comparisons with available full-wave analysis softwares, indicate the efficacy of the proposed method. Filter design with up to 50% bandwidth and the design of shorter lengths of coupled line sections are achievable by the proposed method in part due to the incorporation of impedance matching.

Combined input-crosspoint buffered (CICB) packet switches have been of research interest in the last few years because of their high performance. These switches provide higher performance than input-buffered (IB) packet switches while requiring the crosspoint buffers run at the same speed as that of the input buffers in IB switches. Recently, it has been shown that CICB switches with one-cell crosspoint buffers, virtual output queues, and simple input and output arbitrations, provide 100% throughput under uniform traffic. However, it is of general interest to know the maximum throughput that a CICB switch, with no speedup, can provide under admissible traffic. This paper analyzes the throughput performance of a CICB switch beyond uniform traffic patterns and shows that a CICB switch with one-cell crosspoint buffers can provide 100% throughput under admissible traffic while using no speedup.

We have developed a code-division-multiplexing (CDM) transmission scheme for future road-vehicle communication systems, which uses cyclic shifted-and-extended (CSE) codes generated from a basic code with superior auto-correlation characteristics. This paper proposes to use a Quasi-Orthogonal (QO) sequence as the basic code. Its auto-correlation values are zero except at zero and middle shifts. When the CDM transmission is performed by the CSE codes based on the QO sequence, a desired correlation value is, at a receiver, interfered by the auto-correlation value at middle shift. Therefore, an elimination technique for the interfered correlation value is proposed and realizes zero cross-correlation characteristics within the cyclical shift interval. The new CDM transmission scheme based on the proposed scheme is evaluated by computer simulations in terms of the bit-error-rate performance.

This letter presents mutual coupling reduction in an E-plane arranged microstrip patch array fed by a triplate waveguide. Five mushroom-like electromagnetic band-gap (EBG) elements arranged in one column are embedded both between two radiating patches and between the feeding lines for suppression of the surface wave and the parallel plate mode, respectively. Validity of the proposed EBG elements is confirmed by the measurement.

Binary sequences with good autocorrelation and crosscorrelation properties are widely used in signal processing. If the autocorrelation properties are optimum, then the sequences are called perfect. In this paper we show, that the calculation of the crosscorrelation between Gordon-Mills-Welch sequences and Dillon-Dobbertin sequences is related to the crosscorrelation of m-sequences and their decimations. Furthermore, we give an upper bound for the maximum crosscorrelation coefficient (in absolute value) for certain perfect sequences.