A novel power spectral density accumulation (PSDA) method for estimating the bandwidth of the clutter spectra is proposed, based on a priori knowledge of the shape of the clutter spectra. The comparison of the complexity and the performance between the PSDA method and the general ones is presented. It is shown that the PSDA method is effective for the short-time clutter data in the practical application.

A new rewritable medium utilizing a guest-host (G-H) polymer-dispersed liquid-crystal (PDLC) film has been developed in our laboratory. The medium is thermally written and electrically erased. It is portable, like paper, and can store recorded data because of the memory effect of smectic-A liquid crystal (SmA LC), which exhibits bistable states of homeotropic and focal conic alignment. Dichroic dye is added to the SmA LC to form the G-H type. An evaluation of the characteristics revealed that this medium exhibits both high contrast and good reliability.

Soft bit speech decoding, as a new approach of error concealment, is applied to the mixed excitation linear prediction (MELP) algorithm. Average residual redundancies of the quantized parameters are exploited in the error concealment process as an a priori knowledge of the source. Results show a significant SNR improvement for parameters decoded using the error concealment scheme.

In this paper, we present the division algorithm (DA) for the computation of b=c/a over GF(2m) in two aspects. First, we derive a new formulation for the discrete-time Wiener-Hopf equation (DTWHE) Ab = c in GF(2) over any basis. Symmetry of the matrix A is observed on some special bases and a three-step procedure is developed to solve the symmetric DTWHE. Secondly, we extend a variant of Stein's binary algorithm and propose a novel iterative division algorithm EB*. Owing to its structural simplicity, this algorithm can be mapped onto a systolic array with high speed and low area complexity.

This paper presents a historical review of fiber technologies from the 1970s till now, focused on design, transmission characteristics, and reliability assurance of silica optical fibers. Discussion is made by dividing the period into two phases; the first phase closing nearly at the end of the 1980s and the second one starting at the same time. As for the first phase, we present designs of graded-index multimode fiber and single-mode fiber, and development of dispersion shifted fiber. Mechanical reliability assurance and loss increase phenomena due to hydrogen are also described. Development of an optical fiber amplifier triggered the start of the second phase. Due to the introduction of WDM transmission systems as well as demand on high bit-rate transmission, fiber dispersion and nonlinearity have become indispensable factors to be taken into consideration for system design and performance evaluation. We discuss novel non-zero dispersion shifted fibers and dispersion compensating fibers, developed to meet the requirements for long distance and high bit-rate WDM transmission systems. Finally, discussions are made on the future research and development items, which are necessary to realize anticipating photonic networks.

This paper describes design optimization and performances of hybrid optical transmission lines consisting of effective-area-enlarged pure silica core fiber and dispersion compensating fiber. As a result of the design optimization, considering low nonlinearity and good bending characteristic, the developed fibers exhibit a span average loss of 0.208 dB/km, a span average dispersion slope of 0.02 ps/nm2/km and low nonlinearity with an equivalent effective area of 60 µm2. Further optimization of the relationship among the nonlinearity, the dispersion slope and the bending characteristic enables perfectly dispersion-flattened hybrid optical transmission lines exhibiting a low transmission loss of 0.211 dB/km, low nonlinearity with an equivalent effective area of 60 µm2 and small dispersion deviation of 0.03 ps/nm/km in a wavelength band wider than 40 nm.

Services that operate normally, independently, will behave differently when simultaneously initiated with another service. This behavior is called a feature interaction. A feature interaction, where the next state can not be determined uniquely for one event, is called a non-determinacy feature interaction. To detect the interaction, judgment has to be made as to whether the state, where the non-determinacy occurs, is reachable from the initial state or not. For the judgment, many methods have been proposed. But, still now, it is required huge computation time to judge the reachability. This paper proposes a new method to test the reachability using a little knowledge elicited beforehand. By using the proposed method computation time was reduced drastically. Besides, by applying the proposed method to a benchmark, the proposed method was confirmed to be effective and reasonable.

A communication model and a computer assisted communication method are introduced. With this model incorrect communications between humans are explained and then a method to lead successful communications with computer is illustrated. This method improves qualities of communications and can be applied to co-operative works. On the basis of the communication method, we have been developing a co-operative visual software requirements definition method via network with a visual requirements language named VRDL. Our method will improve quality of software requirements specification (SRS).

In this paper, a novel method to reduce additive time-varying noise is proposed. Unlike the previous methods, the proposed method requires neither the assumption about noise nor the estimate of the noise statistics from any pause regions. The enhancement is performed on a band-by-band basis for each time frame. Based on both the decision on whether a particular band in a frame is speech or noise dominant and the masking property of the human auditory system, an appropriate amount of noise is reduced in time-frequency domain using modified spectral subtraction. The proposed method was tested on various noisy conditions: car noise, F16 noise, white Gaussian noise, pink noise, tank noise and babble noise. On the basis of segmental SNR, inspection of spectrograms and MOS tests, the proposed method was found to be more effective than spectral subtraction with and without pause detection in reducing noise while minimizing distortion to speech.

For the purpose of applying to 50 GHz channel spacing 10 Gb/s DWDM systems, the dispersion reduced fiber Bragg gratings (FBG) is demonstrated. This new FBG is designed by applying in optimized cosine expansion series to the refractive index profile. The 10 π-phase shifts in the refractive index profile realize both square filtering characteristics and linear phase responses resulting in reducing group delay variation in the reflective bandwidth. The FBG, fabricated according to the new design, is tested and shows more than 30 dB isolation for the adjacent channel and less than 10 psec group delay variation in the reflective bandwidth. This small dispersion leads to vast improvement of 10 Gb/s transmission performance. The power penalty of the new FBG is suppressed to 1/6 of that of conventional FBG. Furthermore, the symmetrical refractive index profile, realized by applying a cosine expansion series, shows that these optical characteristics have no dependence of the light launching direction. From these results, this new design offers an FBG suitable for the ADM used in 10 Gb/s DWDM systems.

We investigate a method to suppress the polarization-dependent loss (PDL) of long-period fiber gratings (LPFGs). We study the origins of the PDL and propose an azimuthally isotropic UV exposure to suppress the UV-induced birefringence and to realize low-PDL LPFGs. By using this technique and a low birefringent fiber together, the PDL of LPFGs can be reduced to a sufficiently low level required in high performance communication systems. Moreover, the validity of our theoretical modeling is confirmed by the experimental results.

The main objective of vehicle suspensions is to improve ride comfort and road holding ability. Though passive suspensions consist of spring and damper, active suspensions adopt an actuator in addition to passive suspensions. In this paper, a quarter car model with an asymmetric hydraulic actuator is used. Moreover, the damping coefficient of the damper, which is changed according to the actuator velocity, is considered. The LPV (Linear Parameter Varying) model is obtained by applying feedback linearization technique. Next, a gain-scheduled controller, based on LQ regulator with different weighting factor, is designed according to the actuator velocity and the stability of the proposed controller is also proved. The effectiveness of the proposed controller is shown by numerical simulations.

The long-term predictor (LTP) can effectively reduce the redundancy of the quasi-periodicity of speech signals. Traditional pitch predictors in linear predictive coding systems are developed by assuming that pitch gains are constant in each processing subframe. In this paper, we introduce a time-varied prediction gain to achieve a better representation of speech periodicity than the traditional approach. Due to the non-stationary variation of speech, the proposed LTP method can trace the detailed fluctuation of speech amplitude in both transient and stationary periods. Simulation results show that the proposed first-order varied-gain pitch predictor obtains a near speech quality as the fifth-order pitch predictor of the G.723.1 coder does; however, the former requires much lower computation than the latter.

In this paper, we describe design considerations for inverse dispersion fiber (IDF) whose chromatic dispersion is designed to compensate for that of conventional 1.3 µm zero-dispersion single-mode fiber (SMF). We clarify the appropriate structural parameters for W-type, triple-clad-type and ring-type refractive index profiles to realize a hybrid transmission line composed of SMF and IDF taking into consideration the bending sensitivity and the available wavelength bandwidth that achieves an average chromatic dispersion of below 1 ps/nm/km in the 1.55 µm region. We also show that, when the launched power is less than 0 dBm/ch, a hybrid transmission line composed of SMF and IDF provides better 40 Gbps 8 ch dense wavelength division multiplexing (DWDM) transmission performance than a conventional dispersion compensation scheme with a dispersion compensating fiber (DCF) module.

The digital filter which is constructed by Lebesgue spectrum analysis of ergodic theory, is shown to achieve a 15% gain of the number of simultaneous accessible users of asynchronous CDMA communication systems at the same BER (Bite Error Rate) compared to the Gold sequence and random sequence. According to the simulation of asynchronous CDMA communication systems with spreading sequences at the spreading factor of 127, it is shown that the performance gain caused by the digital filter called Lebesgue spectrum filter (LSF) is independent on the nature of spreading sequences.

The reverse link bandwidth efficiency of a spectrally overlapped CDMA system with fast transmit power control is evaluated to find the optimum overlapping, where the bandwidth efficiency is defined as the maximum aggregate bit rate of all subsystems per unit bandwidth (bps/Hz). Single and multiple cell environments are considered. Besides the rectangular chip pulse, the impact of a pulse-shaping filter is discussed. It is found that the raised cosine spectrum pulse shaping helps to increase the bandwidth efficiency and strict pulse shaping filter problem can be avoided if a large number of subsystems are overlapped. It is also found that the optimum carrier spacing remains unchanged irrespective of the power delay profile shape of the multipath channel, whether multipath fading exists or not, and whether a single cell or multiple cell system is considered. However, the bandwidth efficiency strongly depends on them and the impacts of the related parameters are discussed.

A rapid Pseudo-Noise (PN) acquisition scheme is proposed. The proposed scheme consists of a phase alignment detector and Voltage Controlled Clock (VCC) loop. The VCC loop is used to control the phase update of the local PN signal. It has an auxiliary signal that provides the loop with two stable locking points as well as the direction of each phase update. The performance of the proposed scheme is evaluated by simulation. Results show that the proposed scheme acquires the phase two to three times faster than the conventional coherent serial scheme, and 1.5 times faster than of that in [10], at a small amount of additional hardware.

We have developed and demonstrated a novel technique for electrical inspection and electrical failure analysis, which can detect open, high-resistance, and short circuits without the need for electrical contact with the outside of the LSI chip or the board on which the LSI chip is mounted. The basic idea of the technique is the detection of the magnetic field produced by OBIC (optical beam induced current) or photo current. A DC-SQUID (superconducting quantum interference device) magnetometer is used to detect the magnetic field. This scanning laser-SQUID microscopy ("laser-SQUID" for short) has a spatial resolution of about 1.3 µm. It can be used to distinguish defective chips before bonding pad patterning or after bonding without pin-selection. It can localize any defective site in the chip to within a few square microns.

This contribution discusses which information can be derived from estimated directions of arrival (DOAs) and directions of departure (DODs) from a multiple-input multiple-output (MIMO) radio system, and establishes two new parameters describing the multipath spread at both link ends. We find that the multipath component separation, MCS, combines delay, (double-) angular and Doppler dispersion, as appropriate. MCS provides a system-independent radio characterization of propagation environments and aids in selecting optimum positions for smart-antenna deployment. Evaluation of double-directional measurements (antenna arrays at both link ends) in indoor environments show the usefulness and the limits of the multipath component separation concept.

This paper presents an improved spectral subtraction method for speech enhancement. A new noise estimation method is derived in which the noise is assumed to be white. By using the property that a white noise spectrum is flat, high frequency components of a noisy speech spectrum are averaged and the standard deviation of the noise is estimated. This operation is performed in the analysis segment, thus the spectral subtraction method combined with the new noise estimation method does not need non-speech segments and as a result can adapt to non-stationary noise conditions. The effectiveness of the proposed spectral subtraction method is confirmed by experiments.