In the circuit-switching literature, the Least Loaded Path Routing (LLR) concept has been shown to be very simple and efficient. However, it seems that there is no unique definition for the "least busy" path, i.e., how to measure the degree of "busy" of a path. In this paper, we examine six ways of defining the least busy path and a random policy. The performance of these policies is evaluated via both simulation and analysis. Our numerical results show that all policies, include the random policy, have almost the same performance under most of the network configurations. Only under extremely low traffic load conditions, the difference between the policies becomes significant. However, the magnitude of the difference is still very small (about 0.001). Therefore, we conclude that how to select the alternate path does not affect the performance of LLR-based routing algorithms significantly when the call blocking probability is not too small. Instead, we found that the trunk reservation level affects the performance of LLR-based routing algorithms significantly.

In erbium doped optical fiber amplifiers (EDFAs) used in modern high-capacity wavelength division multiplexing (WDM) systems, the gain flatness of EDFA is very important in wide-band long-haul systems. In the EDFAs using the passive gain equalizers, the gain flatness deteriorates due to gain-tilt when the operating condition of the EDFA changes, while the EDFAs should maintain the gain flatness even if the operating condition has changed. To solve this problem, we have developed an active gain-slope compensation technique of an EDFA using a thulium-doped optical fiber (TDF) as a saturable absorber. The actively gain-slope compensated EDFA with the TDF compensator keeps the gain profile constant for the wide gain dynamic range more than 8 dB with the low noise figure less than 6 dB in the wavelength range of 1539-1564 nm.

This paper proposes a nonlinear distortion suppression scheme for optical direct FM Radio-on-Fiber system. This scheme uses the interaction between the nonlinearities of DFM-LD and OFD to suppress a 3rd order intermodulation distortion. We theoretically analyze the carrier to noise-plus-distortion ratio (CNDR) and show a controlling method in the MZI type OFD to realize the proposed suppression scheme.

In erbium doped optical fiber amplifiers (EDFAs) used in modern high-capacity wavelength division multiplexing (WDM) systems, the gain flatness of EDFA is very important in wide-band long-haul systems. In the EDFAs using the passive gain equalizers, the gain flatness deteriorates due to gain-tilt when the operating condition of the EDFA changes, while the EDFAs should maintain the gain flatness even if the operating condition has changed. To solve this problem, we have developed an active gain-slope compensation technique of an EDFA using a thulium-doped optical fiber (TDF) as a saturable absorber. The actively gain-slope compensated EDFA with the TDF compensator keeps the gain profile constant for the wide gain dynamic range more than 8 dB with the low noise figure less than 6 dB in the wavelength range of 1539-1564 nm.

This paper presents the outline of the systolic array recursive least-squares (RLS) processor prototyped primarily with the aim of broadband mobile communication applications. To execute the RLS algorithm effectively, this processor uses an orthogonal triangularization technique known in matrix algebra as QR decomposition for parallel pipelined processing. The processor board comprises 19 application-specific integrated circuit chips, each with approximately one million gates. Thirty-two bit fixed-point signal processing takes place in the processor, with which one cycle of internal cell signal processing requires approximately 500 nsec, and boundary cell signal processing requires approximately 80 nsec. The processor board can estimate up to 10 parameters. It takes approximately 35 µs to estimate 10 parameters using 41 known symbols. To evaluate signal processing performance of the prototyped systolic array processor board, processing time required to estimate a certain number of parameters using the prototyped board was comapred with using a digital signal processing (DSP) board. The DSP board performed a standard form of the RLS algorithm. Additionally, we conducted minimum mean-squared error adaptive array in-lab experiments using a complex baseband fading/array response simulator. In terms of parameter estimation accuracy, the processor is found to produce virtually the same results as a conventional software engine using floating-point operations.

Elliptic curve cryptosystems are based on the elliptic curve discrete logarithm problem (ECDLP). If elliptic curve cryptosystems avoid FR-reduction and anomalous elliptic curve over Fq, then with current knowledge we can construct elliptic curve cryptosystems over a smaller definition field. ECDLP has an interesting property that the security deeply depends on elliptic curve traces rather than definition fields, which does not occur in the case of the discrete logarithm problem (DLP). Therefore it is important to characterize elliptic curve traces explicitly from the security point of view. As for FR-reduction, supersingular elliptic curves or elliptic curve E/Fq with trace 2 have been reported to be vulnerable. However unfortunately these have been only results that characterize elliptic curve traces explicitly for FR- and MOV-reductions. More importantly, the secure trace against FR-reduction has not been reported at all. Elliptic curves with the secure trace means that the reduced extension degree is always higher than a certain level. In this paper, we aim at characterizing elliptic curve traces by FR-reduction and investigate explicit conditions of traces vulnerable or secure against FR-reduction. We show new explicit conditions of elliptic curve traces for FR-reduction. We also present algorithms to construct such elliptic curves, which have relation to famous number theory problems.

The present paper discusses several promising application areas for optical data links based on high-performance vertical-cavity surface-emitting laser diodes (VCSELs). Both 850 and 980 nm emission wavelength devices realized in the GaAs-AlGaAs or InGaAs-AlGaAs material systems are considered. We show data transmission results of 10 Gb/s signals at 830 nm wavelength over a new high-bandwidth multimode silica fiber of up to 1.6 km length. The same fiber type is employed to demonstrate the first 40 Gb/s transport over 300 m distance by means of a 4-channel coarse wavelength-division multiplexing approach. A first 1 10 linear VCSEL array capable of 10 Gb/s per channel operation is presented for use in next generation parallel optical modules. To improve the singlemode emission characteristics for output power in the 5 mW range we introduce a new device concept incorporating a long monolithic cavity. For low-cost short-distance data links we investigate graded-index polymer optical fibers and report on up to 9 Gb/s transmission over a length of 100 m. Polymer waveguides are also used in an optical layer of a hybrid electrical-optical printed circuit board. Transmitted 10 Gb/s optical data over a prototype board show the potential of this new technology. Finally we present two-dimensional VCSEL arrays for highly parallel data transport on a CMOS chip level. Both 980 and 850 nm bottom emitting devices with modulation capabilities up to 12.5 Gb/s are discussed.

Photonic crystals have seen major advances in the past few years in the optical range. The association of in-plane waveguiding and two-dimensional photonic crystals (PCs) in thin-slab or waveguide structures leads to good 3D confinement with easy fabrication. Such structures, much easier to fabricate than 3D PCs open many exciting opportunities in optoelectronic devices and integrated optics. We present experiments on a variety of structures and devices, as well as modelling tools, which show that 2D PCs etched through waveguides supported by substrates are a viable route to high-performance PC-based photonic integrated circuits (PICs). In particular, they exhibit low out-of-plane diffraction losses. Low-loss waveguides, high finesse microcavities, and their mutual coupling are demonstrated. PACS: 42.70 QS, 42.55 Sa, 42.82 m, 42.50-p.

We fabricated a 1.55-µm polarization insensitive Michelson interferometric wavelength converter (MI-WC). The MI-WC consists of a two-channel spot-size converter integrated semiconductor optical amplifier (SS-SOA) on a planar lightwave circuit (PLC) platform. Clear eye opening and no power penalty in the back-to-back condition were obtained at 10 Gb/s modulation. We also confirmed the polarization insensitive operation on the input signal. Moreover, for an application of the MI-WC to DWDM networks, we demonstrated the selective wavelength conversion of 2.5 G/s optical packets from Fabry-Perot laser diode (FP-LD) light to four ITU-T grid wavelengths. We confirmed the good feasibility of this technique for use in DWDM networks. The wavelength conversion we describe here is indispensable for future all-optical networks, in which optical signal sources without wavelength control will be used at user-end terminals.

This paper describes a simple polarization-independent wavelength conversion method using degenerated four-wave mixing (FWM) in single-mode fibers pumped with cross-polarized high frequency, saw-tooth pulses from a single pump source. Successful polarization-independent wavelength conversion is experimentally confirmed with less than 12% and 5.6% variation using a gain-switched LD pumping and a mode-locked fiber laser pumping, respectively. We clarify that the interference effect between two orthogonal pump pulses must be taken into account to achieve a good polarization-insensitive operation, since even the small pulse edges bring about the large polarization fluctuations when they are interfered. Furthermore, it is reveal that the shorter pump pulse broadens its own spectrum due to the self-phase modulation in fibers, resulting in poor FWM efficiency. Finally, possibility of high-speed operation is discussed taking into account the pump pulse conditions.

We propose a novel optical add/drop multiplexer (OADM) utilizing free spectral range (FSR) periodicity of an arrayed-waveguide multiplexer (AWG). In this OADM, wavelength-division multiplex (WDM) signal is multiplexed and/or de-multiplexed in two steps. Power penalty due to coherent crosstalk is drastically reduced compared with that of conventional OADM where AWG multiplexers are opposite to each other. The calculated power penalty due to the coherent crosstalk is about 0.7 dB after the 16 OADMs in the case of 128 wavelengths. It was confirmed through a computer simulation that more than one hundred channels at 10 Gbps data rate could be accommodated in an OADM network with 16 nodes. These results show that the OADM network with over 1 Tbps capacity and 16 nodes could be constructed.

A photonic crystal fibre has an array of microscopic air holes running along its length. The periodicity of the array is broken by a deliberate "defect" that acts as a waveguide core. Light is confined to this core by the holes. Although some designs of photonic crystal fibre guide light by total internal reflection and so can be considered analogues of conventional optical fibres, their properties can be strikingly different. Other designs guide light by photonic bandgap confinement and represent a totally new type of fibre.

In order to realize automatic-level-controlled (ALC) erbium doped fiber amplifiers (EDFAs) with both wide dynamic range and good noise performance, we propose EDFAs employing the automatic power control (APC) scheme and a variable attenuation slope compensator (VASC). The VASC consists of two asymmetrical Mach-Zehnder interferometers (MZIs) concatenated in series and thermo optic (TO) heaters are attached to the arms of each MZIs. By adjusting the electric power supplied to the TO heaters, an almost linear attenuation slope can be varied by plus minus 5 dB or more over the operational wavelength band of 30 nm. The EDFA employing the APC scheme and the VASC has exhibited a dynamic range as large as 20 dB with the output power variation as small as 0.7 dB, which is as good as that of the EDFA employing the APC scheme and a variable optical attenuator (VOA). The noise figure (NF) of the EDFA employing the VASC was degraded about 4.1 dB with increasing the input power by 20 dB, while it was degraded about 7.3 dB with increasing the input power by only 15 dB in the EDFA employing the VOA. The EDFA employing the VASC can realize the ALC operation over a wider dynamic range with reduced noise figure degradation. In the EDFA employing the VASC, the power excursion was suppressed to less than 1.1 dB, when the input signal level was changed between -23 dBm/ch and -18 dBm/ch with the rise/fall time of 8 ms.

In an ideal fiber grating having a uniform refractive index modulation, the reflection or the transmission spectrum is symmetric with equal amount of side lobes on both sides of the resonant wavelength of the fiber grating. It is observed that a long-period fiber grating made by a non-uniform UV laser beam through a uniform amplitude mask has an asymmetric transmission spectrum. The asymmetric characteristic is explained with Mach-Zehnder effect in the long-period fiber grating. The non-uniform UV laser beam makes also a non-uniform index modulation along the fiber core. Therefore, a beam coupled to a cladding mode at a section of the grating can be re-coupled to the core mode after passing a certain distance. The re-coupled beam makes Mach-Zehnder-like interference with the un-coupled core mode. However, it is presented that the asymmetric phenomenon can be overcome by scanning the UV laser beam along the fiber over the mask. The beam scanning method is able to suffer the same fluence of the UV laser beam on the fiber. Finally, a linearly chirped long-period fiber grating was made using the non-uniform UV laser beam. Due to the asymmetricity the chirping effect was not clearly observed. It is also presented that the beam scanning method could remove the asymmetric problem and recover the typical spectrum of the linearly chirped fiber grating.

We propose a new structure of decision feedback adaptive equalizer (DFE) suitable for use in mobile radio systems. The proposed structure named Commutating Decision Feedback Equalizer (CDFE) has two DFEs that operate in a commutating fashion; the two DFEs commutate between training and equalization. Such a commutating operation effectively lengthens the equalizer tracking period over time variant channels. Thus, the CDFE has a superior performance over the conventional DFE in fading channels. Simulation results are presented in the paper.

We investigate a state dependent multicast routing scheme, called Least Load Multicast Routing (LLMR), for single rate loss networks. The algorithm is based on Least Load Routing (LLR) concept and the approach is to select the least loaded links for establishing connections. An analytical model for LLMR is developed. The accuracy of the analytical model is compared with the simulation results and is found to be very good. We also develop a simplified analytical model for fully symmetrical networks, which is also verified by comparing with simulation results.

This paper focuses on a multi-beam combining scheme for DS-CDMA systems, which has RAKE combiners in multiple overlapped beams, in order to increase the reverse link capacity of DS-CDMA. This scheme is a very attractive technique because the maximal ratio combining (MRC) is carried out in space and time domains. However, in a practical situation, since the terminals in own sector are not uniformly located, the interference levels in respective beams are different. Therefore, receivers at the base station do not achieve ideal combining. This paper proposes a multi-beam combining scheme for DS-CDMA systems using weighting factor based on interference level of each beam. A fast closed loop transmission power control (TPC) scheme for the multi-beam combining system is also proposed. It is confirmed by computer simulation that the proposed scheme has excellent performance in the reverse link even if terminals in own sector are not uniformly located.

Signal path loss and propagation delay spread were measured at microwave frequencies of 3.35, 8.45, and 15.75 GHz along a straight quasi line-of-sight (LOS) street in an urban environment under different traffic conditions: daytime and nighttime. Comparison between daytime and nighttime measurements reveals that the break points shift toward the base station because of the increase in the effective heights of the road and sidewalk; break points were not seen during the daytime at a mobile antenna height (hm) of 1.6 m. According to the cumulative probabilities of the delay spreads during the nighttime, frequency dependence is not clearly observed and the delay spreads for hm = 1.6 m were clearly larger than those for hm = 2.7 m. This is because a lower hm results in stronger blocking of the LOS wave, as was also observed during the daytime. The plot of path losses versus delay spreads is confirmed to be represented by an exponential curve. The exponential coefficients during the daytime were observed to be greater than those during the nighttime. This indicates that a LOS wave is more likely to be blocked during the daytime.

We have measured the temperature dependence of the gain characteristics in 1.3-µm AlGaInAs/InP strained multiple-quantum-well (MQW) semiconductor lasers using Hakki-Paoli method. By measuring the temperature dependences of the peak gain value and the gain peak wavelength, we evaluated the temperature dependences of the threshold current and the oscillation wavelength, respectively. The small temperature dependence of the threshold current in AlGaInAs/InP lasers is caused by the small temperature dependence of the transparency current density, which is represented by the characteristic temperature TJtr of 116 K. In AlGaInAs/InP high T0 lasers, the temperature dependence of the oscillation wavelength is slightly larger than that in GaInAsP/InP lasers because of the larger temperature dependence of bandgap wavelength 0.55 nm/K.

In this paper, we investigate the performance characteristics of parallel switching architectures constructed by a stack of multistage switching networks. We first find that the performances of the previously proposed parallel switching architectures are much worse than the expected ones from analytic models which are based on the assumption that traffic is uniformly distributed at each stage of a switching network. We show that this phenomenon is closely related to a traffic-distribution capability of a parallel switching system and has a large influence on the performance. From these results, we then propose an architectural solution based on the Generalized Shuffle Network (GSN) and analyze its performance by proposing a new iterative analysis method. The proposed architecture uses self-routing and deflection routing, and inherently has a traffic-distribution capability to improve switch performances such as cell loss and delay in a cost-effective manner. From the comparison of simulation and analysis results, it is shown that the developed models are quite accurate in predicting the performance of a new parallel switching system.