In this letter, we propose a blind adaptive receiver with nonlinear structure for DS/CDMA communication systems. The proposed receiver requires the signature waveform and timing for only the desired user. It is shown that the blind adaptation is equivalent to the adaptation with the training signal and the function to be minimized has no local minima.

In order to highlight a rapid progress attained in the field of millimeter waves in Japan, this paper describes several key topics including transistors, integrated circuits, planar antennas, millimeter wave photonics, and others.

A 3V-50 MHz analog CMOS current-mode continuous-time active filter with a negative resistance load (NRL) is proposed. In order to design a current-mode current integrator, a modified basic current mirror with a NRL to increase the output resistance is employed. The inherent circuit structure of the designed NRL current integrator, which minimizes the internal circuit nodes and enhances the gain bandwidth product, is capable of making the filter operate at the high frequency. The third order Butterworth low pass filter utilizing the designed NRL current integrator is synthesized and simulated with a 1.5 µm CMOS n-well process. Simulation result shows the cutoff frequency of 50 MHz and power consumption of 2.4mW/pole with a 3V power supply.

Preliminary experiments on non-destructive quantitative analysis of water vapor density in halogen lamps have been carried out. A working curve showing a relation between absorbance and water vapor density was successfully obtained by using frequency-stabilized InGaAsP/InP semiconductor laser spectrometric system.

In this paper, an exact-minimization method for an AND-EXOR expression (ESOP) using O-suppressed binary decision diagrams (ZBDDs) is considered. The proposed method is an improvement of Sasao's MRCF-based method. From experimental results, it is shown that required ZBDD size is reduced to 1/3 in the best case compared with the MRCF-based method.

Asynchronous Transfer Mode (ATM) is considered to bo the key technology for realizing B-ISDN. This paper discusses current research on ATM switching nodes for high-speed communication networks. Although some ATM switching nodes have been deployed, much work continues for resolving problems as regards operations and maintainability, such as ATM layer performance evaluation including layered management scheme upon detection of line failure, function test methods regarding channel connectivity for multicasting, and real-time ATM traffic-monitoring mechanism with QoS control. To achieve sufficient ATM node maintainability, the ATM cell transfer quality on the VP and VC levels should be ensured both within the ATM nodes and between adjacent ATM nodes. Since ATM switching nods handle many kinds of virtual paths and virtual channels, each channel's connectivity must be confirmed. This paper proposes ATM layer performance evaluation concept, layered management scheme upon detection of line failure, function test methods for a multicast switch using test cells that periodically pass through pre-determined switching path routes. It also proposes the concept of test cell generation for simulating multiplexed ATM test cells taking ATM truffic characteristics into account. Furthermore, this paper describes a fault diagnosis scheme using test cells that can continually observe the entire ATM connection length in the system. A real-time traffic monitoring hardware configuration and an interface with software control are also discussed and it is clarified that the required functions can be realized by using commercially available DSPs.

This paper gives an overview of the research and development trends in millimeter-wave short-range application systems, such as communication systems and sensing systems, in Japan and other countries. Frequency management trends are also described. Major research and development efforts in Japan have currently been concentrated on the 59-64 GHz band. The first major achievement resulting from those efforts was the allocation of the 60-61 GHz band to the automotive radar systems. Test productions of automotive radars in this band have already started. Further technological developments to reduce the cost and size of radar products are, however, required in order for such radar systems to be widely used. Development of broadband wireless LAN systems has also been intensively made in the 60 GHz band. In addition, technical issues related to standardization of millimeter-wave wireless LAN systems in the 60 GHz band have been examined at the Association of Radio Industries and Businesses. The application areas of millimeter-waves in the future are expected to become more diverse. Research and development trends of future application systems, such as broadband mobile communication systems and imaging radar systems, are also described. These systems require more advanced millimeter-wave technologies, such as smart antennas, low power-consumption devices, and more sensitive detectors. Efforts to develop these technologies must be strengthened.

This paper describes how to effectively use discriminative training based on Minimum Classification Error (MCE) criterion for a small amount of data in order to attain the highest level of recognition performance. This method is a combination of MCE training and Vector-Field-Smoothed Bayesian learning called MAP/VFS, which combines maximum a posteriori (MAP) estimation with Vector Field Smoothing (VFS). In the proposed method, MAP/VFS can significantly enhance MCE training in the robustness of acoustic modeling. In model training, MCE training is performed using the MAP/VFS-trained model as an initial model. The same data are used in both trainings. For speaker adaptation using several dozen training words, the proposed method has been experimentally proven to be very effective. For 50-word training data, recognition errors are drastically reduced by 47% compared with 16.5% when using only MCE. This high rate, in which 39% is due to MAP, an additional 4% is due to VFS, and a further improvement of 4% is due to MCE, can be attained by enhancing MCE training capability by MAP/VFS.

For quasi millimeter-wave and millimeter-wave high-speed wireless communications over wireless LANs and wireless ATMs, narrow beam antennas have been shown to provide high transmission quality by suppressing the troublesome multipath effect. However, the diameter of sector antennas needed to create the narrow beams rapidly increases with the sector number. In addition, the cylindrical shape of typical sector antennas does not suit portable terminals. This paper shows a methodology for designing planar sector antennas that overcomes these problems. The proposed antenna uses two kinds of beams and the antenna gains are equalized in all sectors. The antenna is developed as a 4-beam subarray fed by a planar Butler matrix circuit. The design method of the subarray and an evaluation of its characteristics in the 20 GHz band are discussed.

The polymer matrix for the number of N in-puts/outputs, N stages and 2x2-switches is denoted as the 1-D Spanke-Benes (SB) network. Throughout the paper, the 1-D SB-network, which equals the diamond cellular array, is extended to arbitrary dimensions by a mathematical transformation (a 1-D network provides the interconnection of 1-D data). This transformation determines the multistage architecture completely by providing size, location, geometry and wiring of the switches as well as it preserves properties of the networks, e.g., the capability of sorting. The SB-networks of dimension 3 are analysed and sorting is applied.

This paper analyzed the connection points of Main Distribution Frames (MDF), which are installed between outside plants and inside plants (service nodes). This paper also proposes a connecting system for forthcoming FITL (Fiber In The Loop) networks. NTT has developed the Subscriber Line Cross-Connecting Module (LXM) for the FITL network and will continue to introduce LXMs and deploy optic subscriber networks in big cities throughout Japan.

One of the functions that should be provided in ATM LANs is multicast communication. For multicast communication on ATM LANs, the architecture of switch fabric and protocols for signaling have been studied. However, when data communication using a multicast connection such as LAN emulation service is provided, ABR service on a multicast connection (Multicast ABR) is also required. ABR service has been actively discussed in the ATM forum. Unfortunately, the study on flow control mechanism for Multicast ABR is not enough. This paper discusses the suitable flow control mechanism for Multicast ABR and shows its performance.

This paper presents a method for simply estimating characteristics of signals received by a millimeter wave car radar. In this method, the substitution of a radar target with a set of scattering points is introduced to take account of the phenomenon that only a part of the target is irradiated with the radio wave from the radar antenna with a sharp beam; the phenomenon is peculiar to the car radar which operates in a compact range. The positions of these scattering points and the RCS values for the scattering points are appropriately determined on the basis of a measured RCS image for the target. The RCS image means a spatial distribution of RCS values on the surface of the target. In addition, influence of the ground, which is a dominant clutter in car radar environments, and characteristics of the car radar hardware can be included in the estimation method. The estimated characteristics of the signal received by the car radar are compared with the measured ones under typical cases in the car radar environments. The comparison verifies not only that the received signal characteristics are well estimated even when the range is rather short but also that the substitution of the target with scattering points is valid. The proposed method can realize the estimation of the received signal characteristics. Furthermore, the method can be developed into a computer simulation for evaluating the target detection performance of the car radar.

When wireless multi-media information which includes speech, image, data and so on are transmitted, the defference in information rate, required quality as well as traffic performance should be taken into account. A wireless spread spectrum system can achieve a flexible balance of these differences because of the inherent asynchronous capability of CDMA. In this paper, we propose a wireless multi-media CDMA system based on a processing gain control in a dynamic traffic channel. According to the priority of each medium and channel measurement information i.e. traffic, the optimal processing gain can be controlled by using Nonlinear Programming. Numerical results demonstrate that the proposed method possesses higher flexible capacity than TDMA in a dynamic multi-medea traffic channel.

A generalized Reed-Muller expression (GRM) is obtained by negating some of the literals in a positive polarity Reed-Muller expression (PPRM). There are at most 2(n2)^(n-1) different GRMs for an n-variable function. A minimum GRM is one with the fewest products. This paper presents certain properties and an exact minimization algorithm for GRMs. The minimization algorithm uses binary decision diagrams. Up to five variables, all the representative functions of NP-equivalence classes were generated and minimized. Tables compare the number of products necessary to represent four-and five-variable functions for four classes of expressions: PPRMs, FPRMs, GRMs and SOPs. GRMs require, on the average, fewer products than sum-of-products expressions (SOPs), and have easily testable realizations.

The inclusion of the non-quasi-static effect is crucial in the simulation of the microwave circuits for MOS transistors. This report proposes a simple model which includes this effect in small-signal simulation. The simulated results are consistent with the measured data up to a frequency that is 30 times higher frequency than the cut-off frequency.

In the envisaged Universal Mobile Telecommunications System (UMTS), the satellite component will have to provide services to mobile or, in some cases, hand held terminals with a required grade of user co-operation and link availability in various communication environments. This may require the capability of the satellite link to cope with more severe multipath environments than those for which mobile satellite links are most frequently designed (maritime or open rural applications); unfortunately, when the mobile radio channel is affected by multipath and a coherent demodulation is chosen, the phase synchronisation can be a critical issue. To satisfactorily deal with the arising difficulties, a dual channel demodulation is a viable and efficient strategy for the forward link, since only one common pilot channel is needed in this case. If the same dual channel demodulation is considered for the return link, an unacceptable capacity reduction may result. In this paper, some synchronisation strategies are analysed and an efficient dual channel demodulation scheme is proposed for the return link of a satellite DS-CDMA mobile communication system; furthermore, the impact on the overall system performance or capacity is analysed.

In this paper, a simple frame synchronization system for M-ary/SS communication systems is proposed, and synchronization performance and the resulting bit error rate performance are analyzed. The frame synchronization system uses racing counters and framing chips which are added to spreading sequences. M-ary/SS communication systems can improve bit error rate performance under the condition in which there is an additive white gaussian noise. Synchronization of M-ary/SS communication systems is difficult, however, because M-ary/SS communication systems have several spreading sequences. The authors proposed the simple frame synchronization system which uses only one chip in the spreading sequence as a framing signal. This system needs a long time for initial acquisition as the frame length is longer. The proposed system in this paper can make initial acquisition time short by increasing the number of framing chips. The proposed system corresponds to the conventional system when the number of framing chips is l. As the result, it is shown that several framing chips contribute to decrease the initial acquisition time. Moreover, the frame synchronization system can be applied to asynchronous M-ary/SSMA system when different framing chip pattern is assigned to each user.

The Time-Slicing paradigm is a newly developed method for the training of neural networks for speech recognition. The neural net is trained to spot the syllables in a continuous stream of speech. It generates a transcription of the utterance, be it a word, a phrase, etc. Combined with a simple error recovery method the desired units (words or phrases) can be retrieved. This paradigm uses a recurrent neural network trained in a modular fashion with natural connectionist glue. It processes the input signal sequentially regardless of the input's length and immediately extracts the syllables spotted in the speech stream. As an example, this character string is then compared to a set of possible words, picking out the five closest candidates. In this paper we describe the time-slicing paradigm and the training of the recurrent neural network together with details about the training samples. It also introduces the concept of natural connectionist glue and the recurrent neural network's architecture used for this purpose. Additionally we explain the errors found in the output and the process to reduce them and recover the correct words. The recognition rates of the network and the recovery rates for the words are also shown. The presented examples and recognition rates demonstrate the potential of the time-slicing method for continuous speech recognition.

Mechanism of the noise generation caused by the optical feedback in semiconductor laser was experimentally determined. Two types of the mode competition phenomena were confirmed to be the generating mechanisms. Applicability of the self-sustained pulsation to be a noise reduction method was also discussed.