Wi-Fi-based person identification (PI) tasks are performed by analyzing the fluctuating characteristics of the Channel State Information (CSI) data to determine whether the person's identity is legitimate. This technology can be used for intrusion detection and keyless access to restricted areas. However, the related research rarely considers the restricted computing resources and the complexity of real-world environments, resulting in lacking practicality in some scenarios, such as intrusion detection tasks in remote substations without public network coverage. In this paper, we propose a novel neural network model named SimpleViTFi, a lightweight classification model based on Vision Transformer (ViT), which adds a downsampling mechanism, a distinctive patch embedding method and learnable positional embedding to the cropped ViT architecture. We employ the latest IEEE 802.11ac 80MHz CSI dataset provided by [1]. The CSI matrix is abstracted into a special “image” after pre-processing and fed into the trained SimpleViTFi for classification. The experimental results demonstrate that the proposed SimpleViTFi has lower computational resource overhead and better accuracy than traditional classification models, reflecting the robustness on LOS or NLOS CSI data generated by different Tx-Rx devices and acquired by different monitors.

This paper proposes an algorithm for estimating the location of wireless access points (APs) in indoor environments to realize smartphone positioning based on Wi-Fi without pre-constructing a database. The proposed method is designed to overcome the main problem of existing positioning methods requiring the advance construction of a database with coordinates or precise AP location measurements. The proposed algorithm constructs a local coordinate system with the first four APs that are activated in turn, and estimates the AP installation location using Wi-Fi round-trip time (RTT) lateration and the ranging results between the APs. The effectiveness of the proposed algorithm is confirmed by conducting experiments in a real indoor environment consisting of two rooms of different sizes to evaluate the positioning performance of the algorithm. The experimental results showed the proposed algorithm using Wi-Fi RTT lateration delivers high smartphone positioning performance without a pre-constructed database or precise AP location measurements.

This paper indicates a design methodology of Wi-Fi round-trip time (RTT) ranging for lateration through the performance evaluation experiments. The Wi-Fi RTT-based lateration needs to operate plural access points (APs) at the same time. However, the relationship between the number of APs in operation and ranging performance has not been clarified in the conventional researches. Then, we evaluate the ranging performance of Wi-Fi RTT for lateration focusing on the number of APs and channel-usage conditions. As the results, we confirm that the ranging result acquisition rates decreases caused by increasing the number of APs simultaneously operated and/or increasing the channel-usage rates. In addition, based on positioning performance comparison between the Wi-Fi RTT-based lateration and the Wi-Fi fingerprint method, we clarify the points of notice that positioning by Wi-Fi RTT-based lateration differs from the conventional radio-intensity-based positioning. Consequently, we show a design methodology of Wi-Fi RTT ranging for lateration as the following three points: the important indicators for evaluation, the severeness of the channel selection, and the number of APs for using. The design methodology will help to realize the high-quality location-based services.

As smartphones have become widespread in the past decade, Wi-Fi signal-based crowd estimation schemes are receiving increased attention. These estimation schemes count the number of unique MAC addresses in Wi-Fi signals, hereafter called probe requests (PRs), instead of counting the number of people. However, these estimation schemes have low accuracy of crowd estimation under MAC address randomization that replaces a unique MAC address with various dummy MAC addresses. To solve this problem, in this paper, we propose an indoor crowd estimation scheme using the number of PRs under MAC address randomization. The main idea of the proposed scheme is to leverage the fact that the number of PRs per a unit of time changes in proportion to the number of smartphones. Since a smartphone tends to send a constant number of PRs per a unit of time, the proposed scheme can estimate the accurate number of smartphones. Various experiment results show that the proposed scheme reduces estimation error by at most 75% compared to the conventional Wi-Fi signal-based crowd estimation scheme in an indoor environment.

With the widespread diffusion of Internet of Things (IoT), the number of applications using wireless sensor devices are increasing, and Quality of Service (QoS) required for these applications is diversifying. Thus, it becomes difficult to satisfy a variety of QoS with a single wireless system, and many kinds of wireless systems are working in the same domains; time, frequency, and place. This paper considers coexistence environments of ZigBee and Wi-Fi networks, which use the same frequency band channels, in the same place. In such coexistence environments,ZigBee devices suffer radio interference from Wi-Fi networks, which results in severe ZigBee packet losses because the transmission power of Wi-Fi is much higher than that of ZigBee. Many existing methods to avoid interference from Wi-Fi networks focus on only one of time, frequency, or space domain. However, such avoidance in one domain is insufficient particularly in near future IoT environments where more ZigBee devices and Wi-Fi stations transfer more amount of data. Therefore, in this paper, we propose joint channel allocation and routing in both frequency and space domains. Finally, we show the effectiveness of the proposed method by computer simulation.

After a natural disaster it is critical to urgently find victims buried under collapsed buildings. Most people habitually carry smartphones with them. Smartphones have a feature that periodically transmits Wi-Fi signals called “Probe Requests” to connect with access points. Moreover, smartphones transmit “Clear to Send” when they receive a “Request to Send” alert. This motivated us to develop a hand-held smartphone finder system that integrates a novel method for accurately locating a smartphone using the Wi-Fi signals, to support rescue workers. The system has a unique graphical user interface that tracks target smartphones. Thus, rescue workers can easily reach victims who have their smartphones with them under collapsed buildings. In this paper, after introducing the localization method, the system architecture of the smartphone finder and its prototype system are described, along with some experimental results that demonstrate the effectiveness of the smartphone finder prototype.

Coexistence between ZigBee and Wi-Fi technologies, which operate within the same frequency band, is increasing with the widespread use of the IoT (Internet of Things). ZigBee devices suffer significant decreases in the sink arrival rate of packets in the presence of Wi-Fi interference. To overcome this problem, many channel control methods have been proposed. These methods switch only ZigBee channels to avoid interference with Wi-Fi. In contrast, we propose a cooperative channel control method for improving ZigBee packet arrival rate by controlling both the Wi-Fi and ZigBee channels. Specifically, the proposed method not only controls ZigBee devices and channels but also requests a temporary pause in the use of specific Wi-Fi channels. Finally, computer simulations show the effectiveness of the proposed method from the viewpoints of ZigBee's packet arrival rate and applications' satisfaction. In addition, the feasibility of the proposed method is also confirmed by experiments with prototyping.

Based on the License Assisted Access (LAA) small cell architecture, the LAA coexisting with Wi-Fi heterogeneous networks provide LTE mobile users with high bandwidth efficiency as the unlicensed channels are shared among LAA and Wi-Fi. However, the LAA and Wi-Fi will affect each other when both systems are using the same unlicensed channel in the heterogeneous networks. In such a network, unlicensed band allocation for LAA and Wi-Fi is an important issue that may affect the quality of service (QoS) of both systems significantly. In this paper, we propose an analytical model and conduct simulation experiments to study two allocations for the unlicensed band: unlicensed full allocation (UFA), unlicensed time-division allocation (UTA), and the corresponding buffering mechanism for the LAA data packets. We evaluate the performance for these unlicensed band allocations schemes in terms of the acceptance rate of both LAA and Wi-Fi packet data in LAA buffer queue. Our study provides guidelines for designing channel occupation phase and the buffer size of LAA small cell.

The recent widespread use of high-performance terminals has resulted in a rapid increase in mobile data traffic. Therefore, public wireless local area networks (WLANs) are being used often to supplement the cellular networks. Capacity improvement through the dense deployment of access points (APs) is being considered. However, the effective throughput degrades significantly when many users connect to a single AP. In this paper, users are classified into guaranteed bit rate (GBR) users and best effort (BE) users, and we propose a network model to provide those services. In the proposed model, physical APs and the bandwidths are assigned to each service class dynamically using a virtual AP configuration and a virtualized backhaul network, for reducing the call-blocking probability of GBR users and improving the satisfaction degree of BE users. Finally, we evaluate the performance of the proposed model through simulation experiments and discuss its feasibility.

In this paper, we study Wi-Fi mesh networks (WMNs) as a promising candidate for wireless networking infrastructure that interconnects a variety of access networks. The main performance bottleneck of a WMN is their limited capacity due to the packet collision from the contention-based IEEE 802.11s MAC. To mitigate this problem, we present the distributed link-activation (DLA) protocol which activates a set of collision-free links for a fixed amount of time by exchanging a few control packets between neighboring MRs. Through the rigorous proof, it is shown that the upper bound of the DLA rounds is O(Smax), where Smax is the maximum number of (simultaneous) interference-free links in a WMN topology. Based on the DLA, we also design the distributed throughput-maximal scheduling (D-TMS) scheme which overlays the DLA protocol on a new frame architecture based on the IEEE 802.11 power saving mode. To mitigate its high latency, we propose the D-TMS adaptive data-period control (D-TMS-ADPC) that adjusts the data period depending on the traffic load of a WMN. Numerical results show that the D-TMS-ADPC scheme achieves much higher throughput performance than the IEEE 802.11s MAC.

Wireless technologies that offer high data rate are generally energy-consuming ones while low-energy technologies commonly provide low data rate. Both kinds of technologies have been integrated in a single mobile device for different services. Therefore, if the service does not always require high data rate, the low energy technology, i.e., Bluetooth, can be used instead of the energy-consuming one, i.e., Wi-Fi, for saving energy. It is obvious that energy savings are maximized by turning the unused technology off. However, when active sessions of ongoing services migrate between different technologies, the network-layer connectivity must be maintained, or a vertical handover (VHO) between different networks is required. Moreover, when the networks are not interconnected, the VHO must be fully controlled by the device itself. The device typically navigates traffic through the firmware of the wireless network interface cards (WNIC) using their drivers, which are dependent on the vendors. To control the traffic navigation between WNICs without any modification of the WNICs' drivers, Software-Defined Networking (SDN) can be applied locally on the mobile device, the so called local SDN. In the local SDN architecture, a local SDN controller (SDNC) is used to control a virtual OpenFlow switch, which turns WNICs into its switch ports. Although the SDNC can navigate the traffic, it lacks the global view of the network topology. Hence, to correctly navigate traffic in a VHO process, an extended SDN controller (extSDNC) was proposed in a previous work. With the extSDNC, the SDNC can perform VHO based on a link layer trigger but with a significant packet loss rate. Therefore, in this paper, a framework named esVHO is proposed that executes VHO at the network layer to reduce the packet loss rate and reduce energy consumption. Experiments on VHO performance prove that esVHO can reduce the packet loss rate considerably. Moreover, the results of an energy saving experiment show that esVHO performs high energy saving up to 4.89 times compared to the others.

Wi-Fi Direct is a promising and available technology for device-to-device (D2D) proximity communications. To improve the performances of Wi-Fi Direct communication, optimized radio resource allocations are important. This paper proposes network assisted Wi-Fi Direct (NAWD), which operates based on the media independent services framework of IEEE 802.21 standard, for optimizing radio resource allocations. The NAWD is enhanced Wi-Fi Direct with the assistance of infrastructure networks (e.g., cellular network) and allocates radio resources (e.g., frequency channels and transmit power) to reduce radio interferences among Wi-Fi Direct devices (e.g., smart phones and set-top boxes). The NAWD includes mechanisms for gathering configuration information (e.g., location information and network connection information) of Wi-Fi Direct devices and allocating optimized radio resources (e.g., frequency channels and transmit power) to reduce radio interferences among Wi-Fi Direct devices. Simulation results show that the proposed NAWD increases significantly SINR, power efficiency, and areal capacity compared to legacy Wi-Fi Direct, where areal capacity is total traffic throughput per unit area.

Due to the rapid growth of applications that are based on Internet of Things (IoT) and real-time communications, mobile traffic growth is increasing exponentially. In highly populated areas, sudden concentration of numerous mobile user traffic can cause radio resource shortage, where traffic offloading is essential in preventing overload problems. Vertical handover (VHO) technology which supports seamless connectivity across heterogeneous wireless networks is a core technology of traffic offloading. In VHO, minimizing service interruption is a key design factor, since service interruption deteriorates service performance and degrades user experience (UX). Although 3GPP standard VHO procedures are designed to prevent service interruption, severe quality of service (QoS) degradation and severe interruption can occur in real network environments due to unintended disconnections with one's base station (BS) or access point (AP). In this article, the average minimum handover interruption time (HIT) (i.e., the guaranteed HIT influence) between LTE and Wi-Fi VHO is analyzed and measured based on 3GPP VHO access and decision procedures. In addition, the key parameters and procedures which affect HIT performance are analyzed, and a reference probability density function (PDF) for HIT prediction is derived from Kolmogorov-Smirnov test techniques.

The limitation of the GPS in urban canyon has led to the rapid development of Wi-Fi positioning system (WPS). The fingerprint-based WPS could be divided into calibration and positioning stages. In calibration stage, several grid points (GPs) are selected, and their position tags and featured access points (APs) are collected to build fingerprint database. In positioning stage, real time measurement of APs are compared with the feature of each GP in the database. The k weighted nearest neighbors (KWNN) algorithm is used as pattern matching algorithm to estimate the final positioning result. However, the performance of outdoor fingerprint-based WPS is not good enough for pedestrian navigation. The main challenge is to build a robust fingerprint database. The received number of APs in outdoor environments has large variation. In addition, positioning result estimated by GPS receiver is used as position tag of each GP to automatically build the fingerprint database. This paper studies the lifecycle of fingerprint database in outdoor environment. We also shows that using long time collected data to build database could improve the positioning accuracy. Moreover, a new 3D-GNSS (3D building models aided GNSS) positioning method is used to provide accurate position tags. In this paper, the fingerprint-based WPS has been developed in an outdoor environment near the center of Tokyo city. The proposed WPS can achieve around 17 meters positioning accuracy in urban canyon.

Personal Wi-Fi Hotspot, the Wi-Fi tethering function, is widely deployed on mobile devices to allow other wireless clients to share Internet access via a broadband connection. Its advantages include no connection fee and support of non-3G/LTE devices. However, utilizing this function can rapidly deplete the battery power of the tethering device because both interface connections (3G/LTE and Wi-Fi) are always on. To address this problem, this paper proposes the Energy Management Mechanism for Wi-Fi Tethering Mode on Mobile Devices (EMWT). The mechanism is designed to effectively manage both interfaces by adjusting certain sleep durations according to the incoming traffic. Short, Long, and Deep sleep durations are introduced for saving energy. EMWT can also guarantee the packet delay bound by limiting the maximum sleep period. Five traffic rates, composed of very low, low, medium, high, and very high, are evaluated. NS-3 simulation results reveal that energy savings of up to 52.52% can be achieved with only a slight impact on system performance, in terms of end-to-end delay, throughput, and packet loss.

Wi-Fi P2P has been deployed extensively in mobile devices. However, Wi-Fi P2P is not efficient because it requires an IP layer connection for transmitting even short messages to nearby devices, especially in high density or highly mobile environments owing to the fact that a user on the move has difficulty selecting service-available devices, and a user device has to frequently connect to and be released from nearby devices. This paper proposes a new messaging framework that enables application-level messages to be exchanged between nearby devices with no IP layer connectivity over Wi-Fi P2P. The pre-association messaging framework (PAMF) supports both broadcast and unicast transmission to maximize the delivery success rate, considering the number of peers and messages. Evaluations of PAMF conducted under real scenarios show that application-level messages can be exchanged within a few seconds, with high success rate. PAMF provides high portability and extensibility because it does not breach the Wi-Fi P2P standard. Moreover, the demonstrations show that PAMF is practical for new proximity services such as local marketing and urgent messaging.

This paper identifies a ripple effect problem (REP) that spreads interference to neighbors and proposes a novel channel localization mechanism to decrease the REP in a Wi-Fi system. The proposed mechanism has less blocking probability when compared to a random channel allocation mechanism and also has increased channel reusability. The proposed mechanism in simulation yields less channels BEm as the number of users and Tused increase.

Broadband wireless networks are rapidly expanding over the world. To provide wireless broadband services for Shanghai Expo 2010, pre-research is launched and a test-bed has been developed, in which WiMAX and Wi-Fi mesh are involved. The test-bed shows that Wi-Fi mesh integrated with WiMAX is highly suitable for large-scale activities like the Olympic Games and the World Expo.

The usable throughput of an IEEE 802.11 system for an application is much less than the raw bandwidth. Although 802.11b has a theoretical maximum of 11 Mbps, more than half of the bandwidth is consumed by overhead leaving at most 5 Mbps of usable bandwidth. Considering this characteristic, this paper proposes and analyzes a real-time distributed scheduling scheme based on the existing IEEE 802.11 wireless ad-hoc networks, using USC/ISI's Power Aware Sensing Tracking and Analysis (PASTA) hardware platform. We compared the distributed real-time scheduling scheme with the real-time polling scheme to meet deadline, and compared a measured real bandwidth with a theoretical result. The theoretical and experimental results show that the distributed scheduling scheme can guarantee real-time traffic and enhances the performance up to 74% compared with polling scheme.

The aggregation of Wi-Fi links has been identified as one way of taking advantage of available channels to achieve higher speed data transmission in future cognitive radio networks. However variations in link quality make it difficult to achieve stable performance from aggregated Wi-Fi links. In this paper we present a method for controlling aggregation of Wi-Fi links based on monitoring of link status. We first discuss the requirements for detecting bad-links which degrade the performance of aggregated Wi-Fi links. We then describe the implementation of an enhanced link-status detection algorithm based on monitoring of signal strength and number of retransmissions. In particular, we address the problems of monitoring and recovering links after they have been dropped from use, and adjusting decision thresholds to adapt to changing wireless conditions. Finally, we report the results of tests which demonstrate the effectiveness for attaining efficient aggregation of Wi-Fi links for high throughput under varying wireless conditions.