We consider a similarity control problem for discrete event systems modeled as nondeterministic automata. A nonblocking supervisor was synthesized in the previous work under the assumption that the event occurrence and the current state of the plant are observable. In this letter, we prove that the synthesized supervisor is a maximally permissive nonblocking one.

The Game of Life, a two-dimensional computationally universal cellular automaton, is known to exhibits 1/f noise in the evolutions starting from random configurations. In this paper we perform the spectral analysis on the computation process by a Turing machine constructed on the array of the Game of Life. As a result, the power spectrum averaged over the whole array has almost flat line at low frequencies and a lot of sharp peaks at high frequencies although some regions in which complicated behavior such as frequent memory rewriting occurs exhibit 1/f noise. This singular power spectrum is, however, easily turned into 1/f by slightly deforming the initial configuration of the Turing machine. These results emphasize the peculiarity of the computation process on the Game of Life that is never shared with the evolutions from random configurations. The Lyapunov exponents have positive values in three out of six trials and zero or negative values in other three trails. That means the computation process is essentially chaotic but it has capable of recovering a slight error in the configuration of the Turing machine.

Two points x, y inside a simple polygon P are said to be mutually link-2 visible if there exists the third point z ∈ P such that z is visible from both x and y. The polygon P is link-2 LR-visible if there are two points s, t on the boundary of P such that every point on the clockwise boundary of P from s to t is link-2 visible from some point of the other boundary of P from t to s and vice versa. We give a characterization of link-2 LR-visibility polygons by generalizing the known result on LR-visibility polygons. A new idea is to extend the concepts of ray-shootings and components to those under notion of link-2 visibility. Then, we develop an O(n log n) time algorithm to determine whether a given polygon is link-2 LR-visible. Using the characterization of link-2 LR-visibility polygons, we further present an O(n log n) time algorithm for determining whether a polygonal region is searchable by a k-searcher, k ≥ 2. This improves upon the previous O(n2) time bound [9]. A polygonal region P is said to be searchable by a searcher if the searcher can detect (or see) an unpredictable intruder inside the region, no matter how fast the intruder moves. A k-searcher holds k flashlights and can see only along the rays of the flashlights emanating from his position.

We present a novel hybrid beamforming architecture for high speed 5G technologies. The architecture combines several new concepts to achieve significant hardware and cost reduction for large antenna arrays. Specifically, we employ an on-site code division multiplexing scheme to group several antenna elements into a single analog-to-digital converter (ADC). This approach significantly reduces analog hardware and power requirements by a factor of 8 to 32. Additionally, we employ a novel analog frequency independent beamforming scheme to eliminate phase shifters altogether and allow for coherent combining at the analog front-end. This approach avoids traditional phase-shifter-based approaches typically associated with bulky and inefficient components. Preliminary analysis shows that for an array of 800 elements, as much as 97% reduction in cost and power is achieved using the hybrid beamformer as compared to conventional beamformer systems.

This paper gives an overview on the design process of modulated metasurface (MTS) antennas and focus on their performance in terms of efficiency and bandwidth. The basic concept behind MTS antennas is that the MTS imposes the impedance boundary conditions (IBCs) seen by a surface wave (SW) propagating on it. The MTS having a spatially modulated equivalent impedance transforms the SW into a leaky wave with controlled amplitude, phase and polarization. MTS antennas are hence highly customizable in terms of performances by simply changing the IBCs imposed by the MTS, without affecting the overall structure. The MTS can be configured for high gain (high aperture efficiency) with moderate bandwidth, for wide bandwidth with moderate aperture efficiency, or for a trade-off performance for bandwidth and aperture efficiency. The design process herein described relies on a generalized form of the Floquet wave theorem adiabatically applied to curvilinear locally periodic IBCs. Several technological solutions can be adopted to implement the IBCs defined by the synthesis process, from sub-wavelength patches printed on a grounded slab at microwave frequencies, to a bed of nails structure for millimeter waves: in any case, the resulting device has light weight and a low profile.

The next generation mobile system “5G” are under research, development and standardization for a service start of around year 2020. It is likely to use frequency bands higher than existing bands to have wider bandwidth for high throughput services. This paper reviews technical issues on higher frequency bands applying mobile systems including system trials and use case trials. It identifies expectations for antennas & propagation studies toward 5G era.

Two kinds of composite right/left-handed coaxial lines (CRLH CLs) are designed for an antenna element. The dispersion relations of the infinite periodic CRLH CLs are designed to occur -1st resonance at around 700 MHz, respectively. The designed CRLH CLs comprise a monopole and a choke structure for antenna elements. To verify the resonant modes and frequencies, the monopole structure, the choke structure, and the antenna element which is combined the monopole and the choke structures are simulated by eigenmode analysis. The resonant frequencies correspond to the dispersion relations. The monopole and the choke structures are applied to the coaxially fed antenna. The proposed antenna matches at 710 MHz and radiates. At the resonant frequency, the total length of the proposed antenna which is the length of the monopole structure plus the choke structure is 0.12 wavelength. The characteristics of the proposed antenna has been compared with that of the conventional coaxially fed monopole antenna without the choke structure and the sleeve antenna with the quarter-wavelength choke structure. The radiation pattern of the proposed antenna is omnidirectional, the total antenna efficiency is 0.73 at resonant frequencies, and leakage current is suppressed lesser than -10 dB at resonant frequency. The propose antenna is fabricated and measured. The measured |S11| characteristics, radiation patterns, and the total antenna efficiency are in good agreement with the simulated results.

In order to provide an alternative solution of human machine interfaces, this paper proposed to recognize 10 human hand gestures regularly used in the consumer electronics controlling scenarios based on a three-dimensional radar array. This radar array was composed of three low cost 24GHz K-band Doppler CW (Continuous Wave) miniature I/Q (In-phase and Quadrature) transceiver sensors perpendicularly mounted to each other. Temporal and spectral analysis was performed to extract magnitude and phase features from six channels of I/Q signals. Two classifiers were proposed to implement the recognition. Firstly, a decision tree classifier performed a fast responsive recognition by using the supervised thresholds. To improve the recognition robustness, this paper further studied the recognition using a two layer CNN (Convolutional Neural Network) classifier with the frequency spectra as the inputs. Finally, the paper demonstrated the experiments and analysed the performances of the radar array respectively. Results showed that the proposed system could reach a high recognition accurate rate higher than 92%.

Multi-static Primary Surveillance Radar (MSPSR) has recently attracted attention as a new surveillance technology for civil aviation. Using multiple receivers, Primary Surveillance Radar (PSR) detection performance can be improved by synthesizing the reflection characteristics which change due to the aircraft's position. In this paper, we report experimental results from our proposed optical-fiber-connected passive PSR system with transmit signal installed at the Sendai Airport in Japan. The signal-to noise ratio of experimental data is evaluated to verify moving target detection. In addition, we confirm the operation of the proposed system using a two-receiver setup, to resemble a conventional multi-static radar. Finally, after applying time correction, the delay of the reflected signal from a stationary target remains within the expected range.

It is well known that the power transfer efficiency (PTE) of a wireless power transfer (WPT) system is maximized at a specific coupling coefficient under the fixed system parameters. For an adaptive WPT system, various attempts have been made to achieve the maximum PTE by changing the system parameters. Applying the input matching networks to the WPT system is one of the most popular implementation methods to change the source impedance and improve the PTE. In this paper, we derive the optimum source condition for the given load and the achievable maximum PTE under the optimum source condition in a closed-form. Furthermore, we propose a method to estimate the input impedance, without feedback information, and an input matching network structure that transforms the source impedance into the optimum source obtained from the estimated input impedance. The proposed technique is successfully implemented at a resonant frequency of 13.56MHz. The experimental results are in close agreement with the theoretical achievable maximum PTE and show that the use of only a single matching network can sufficiently achieve a PTE close to the ideal maximum PTE.

We propose a novel bit error rate (BER) analysis model of weighted-type fractional Fourier transform (WFRFT)-based systems with WFRFT order offset Δα. By using the traditional BPSK BER analysis method, we deduce the equivalent signal noise ratio (SNR), model the interference in the channel as a Gaussian noise with non-zero mean, and provide a theoretical BER expression of the proposed system. Simulation results show that its theoretical BER performance well matches the empirical performance, which demonstrates that the theoretical BER analysis proposed in this paper is reliable.

Recent carrier-grade networks use many network elements (switches, routers) and servers for various network-based services (e.g., video on demand, online gaming) that demand higher quality and better reliability. Network log data generated from these elements, such as router syslogs, are rich sources for quickly detecting the signs of critical failures to maintain service quality. However, log data contain a large number of text messages written in an unstructured format and contain various types of network events (e.g., operator's login, link down); thus, genuinely important log messages for network operation are difficult to find automatically. We propose a proactive failure-detection system for large-scale networks. It automatically finds abnormal patterns of log messages from a massive amount of data without requiring previous knowledge of data formats used and can detect critical failures before they occur. To handle unstructured log messages, the system has an online log-template-extraction part for automatically extracting the format of a log message. After template extraction, the system associates critical failures with the log data that appeared before them on the basis of supervised machine learning. By associating each log message with a log template, we can characterize the generation patterns of log messages, such as burstiness, not just the keywords in log messages (e.g. ERROR, FAIL). We used real log data collected from a large production network to validate our system and evaluated the system in detecting signs of actual failures of network equipment through a case study.

This paper proposes optimal beam patterns of analog beamforming for SU (Single User) massive MIMO (Multi-Input Multi-Output) transmission systems. For hybrid beamforming in SU massive MIMO systems, there are several design parameters such as beam patterns, the number of beams (streams), the shape of array antennas, and so on. In conventional hybrid beamforming, rectangular patch array antennas implemented on a planar surface with linear phase shift beam patterns have been used widely. However, it remains unclear whether existing configurations are optimal or not. Therefore, we propose a method using OBPB (Optimal Beam Projection Beamforming) for designing configuration parameters of the hybrid beamforming. By using the method, the optimal beam patterns are derived first, and are projected on the assumed surface to calculate the achievable number of streams and the resulting channel capacity. The results indicate OBPB with a spherical surface yields at least 3.5 times higher channel capacity than conventional configurations.

Semitransparent organic solar cells were fabricated using lamination process. The devices were realized by using two independent substrates with transparent indium-tin-oxide electrode. One substrate was coated with poly(ethylenedioxy-thiophene)/poly(styrenesulfonate) layer and active layer of poly(3-hexylthiophene-2,5-diyl) (P3HT) and (6,6)-phenyl-C61 butyric acid methyl ester mixture. Another substrate was coated with ultra-thin polyethylenimine ethoxylated. The two substrates were laminated using hot press system. The device exhibited semitransparency and showed typical photovoltaic characteristics with open voltage of 0.59 V and short circuit current of 2.9 mA/cm2.

Photon upconversion (UC) is a technique to convert long wavelength light into short wavelength light. UC fluorescence by triplet-triplet annihilation (TTA) follows a mechanism involving two kinds of molecules as sensitizer and emitter. In this study, we constructed the photon UC dyes system that was applicable to weak excitation light and convert the red light into yellow light in high efficiency. The present result will be useful for the purpose of application to optical elements and light medical care.

The AuGe-alloy source and drain (S/D) formed on SiO2/Si(100) by the lithography process was investigated for the scaling of the organic field-effect transistors (OFETs) with bottom-contact geometry. The S/D was fabricated by the lift-off process utilizing the resist of OFPR. The OFETs with minimum channel length of 2.4 µm was successfully fabricated by the lift-off process. The fabrication yield of Au S/D was 57%, while it was increased to 93% and 100% in case of the Au-1%Ge and Au-7.4%Ge S/D, respectively. Although the mobility of the OFETs with Au-7.4%Ge S/D was decreased to 1.1×10-3 cm2/(Vs), it was able to be increased to 5.5×10-2 cm2/(Vs) by the surface cleaning utilizing H2SO4/H2O2 mixture solution (SPM) and post metallization annealing (PMA) after lift-off process, which was higher than that of OFET with Au S/D.

Copper (Cu) electroless plating was conducted on planar and microstructured polydimethylsiloxane (PDMS) substrates. In this study, organic thin films terminated with nitrogen (N)-containing groups, e.g. poly (dimethylaminoethyl methacrylate) brush (PDMAEMA), aminopropyl trimethoxysilane monolayer (APTES), and polydopamine (PDA) were used to anchor palladium (Pd) catalyst. While electroless plating was successfully promoted on all sample surfaces, PDMAEMA was found to achieve the best adhesion strength to the PDMS surfaces, compared to APTES- and PDA-covered PDMS substrates, due to covalent bonding, anchoring effects of polymer chains as well as high affinity of N atoms to Pd species. Our process was also successfully applied to the electroless plating of microstructured PDMS substrates.

Improvement of output and lifetime is a problem for biofuel cells. A structure was adopted in which gelation mixed with agarose and fuel (fructose) was sandwiched by electrodes made of graphene-coated carbon fiber. The electrode surface not contacting the gel was exposed to air. In addition, grooves were added to the gel surface to further increase the oxygen supply. The power density of the fuel cell was examined in terms of the electrode area exposed to air. The output increased almost in proportion to the area of the electrode exposed to air. Optimization of the concentration of fuel, gel, and the amount of enzyme at the cathode were also examined. The maximum power density in the proposed system was approximately 121μW/cm2, an enhancement of approximately 2.5 times that in the case of using liquid fuel. For the power density after 24h, the fuel gel was superior to the fuel liquid.

Technological developments in direction control of axonal outgrowth are a must for advances in regenerative medicine of the nervous system. In order to solve the problem, we fabricate a new neural cell culture sheet by applying the soft lithography technique to micro-patterning of the extracellular matrix and using thin-film biodegradable polymer for the scaffold. Micro-trenches were coated with Dulbecco's phosphate-buffered saline (-) containing laminin, using micro-molding in capillaries (MIMIC), a soft lithography technique. Biodegradable thin films with micro-trenches were fabricated by UV-curing a polyanhydride solution covering the negative SU-8 mold through thiol-ene polymerization. Both approaches were performed conveniently, rapidly, and accurately. It is thought that these techniques are excellent in terms of convenience and high speed, and can contribute greatly to regenerative medicine.

Hydrophobic DNA (H-DNA) nano-film was formed on a thin glass plate of 50μm thick working as a slab optical waveguide. Bromothymol blue (BTB) molecules were immobilized from aqueous solution with direct contacting to the H-DNA nano-film for 20 minutes. From changes in absorption spectra observed with slab optical wave guide (SOWG) during automated solution exchange (SE) processes for 100 times, it was found that about 95% of bromothymol blue (BTB) molecules was immobilized in the H-DNA nano-film with keeping their functionality of color change responsible to pH change in the solution.