Recently, complex orthogonal variable spreading factor (OVSF) codes based on polyphase orthogonal codes have been proposed to support multi-user/multi-rate data transmission services in synchronous direct-sequence code-division multiple access (DS-CDMA) systems. This study investigates the low signal-envelope fluctuation property of the complex OVSF codes in terms of transmission signal trajectories. In addition, a new method is proposed to suppress the envelope fluctuation more strongly at the expense of reducing the number of spreading sequences of the codes.

Mobile phone systems continue to evolve from the 2nd generation, which began in the early 1990s, to the 5th generation, which is now in service. Along with this evolution, the power amplifier (PA) is also evolved. The characteristics required for PA are changing with each generation. In this paper, we will give an overview of the evolution of PAs from the 2nd generation mobile phones such as GSM (global system for mobile communications) to the 5th generation mobile phones that is often called NR (new radio), in particular, the circuit system. Specifically, the following five items will be described. (1) Ramp-up and ramp-down power control circuit corresponding to GSM, (2) Self-bias circuit technology for improving linearity that becomes important after W-CDMA (wideband code division multiple access), (3) Power mode switching methods for improving efficiency at low output power, (4) Power combining methods that have become important since LTE (long term evolution), and (5) Backoff efficiency improvement methods represented by ET (envelop tracking) and Doherty PA.

The Fifth-Generation new radio (5G NR) services that started in 2020 in Japan use a higher peak-to-average power ratio (PAPR) of a modulated signal with a maximum bandwidth of up to 100MHz and support multi-input/multi-output (MIMO) systems even in mobile handsets, compared to the Third-Generation (3G) and/or Fourth-Generation (4G) handsets. The 5G NR requires wideband operation for power amplifiers (PAs) used in handsets under a high PAPR signal condition. The 5G NR also requires a number of operating bands for the handsets. These requirements often cause significand degradation of the PA efficiency, consequently. The degradation is due to wideband and/or high PAPR operation as well as additional front-end loss between a PA and an antenna. Thus, the use of an efficiency enhancement technique is indispensable to 5G NR handset PAs. An envelope tracking (ET) is one of the most effective ways to improve the PA efficiency in the handsets. This paper gives recent progress in ET power amplifiers (ETPAs) followed by a brief introduction of ET techniques. The introduction describes a basic operation for an ET modulator that is a key component in the ET techniques and then gives a description of some kinds of ET modulators. In addition, as an example of a 5G NR ETPA, the latest experimental results for a 5G ETPA prototype are demonstrated while comparing overall efficiency of the ET modulator and PA in the ET mode with that in the average power tracking (APT) mode.

We propose a speech analysis-synthesis and deep neural network (DNN)-based text-to-speech (TTS) synthesis framework using Gaussian mixture model (GMM)-based approximation of full-band spectral envelopes. GMMs have excellent properties as acoustic features in statistic parametric speech synthesis. Each Gaussian function of a GMM fits the local resonance of the spectrum. The GMM retains the fine spectral envelope and achieve high controllability of the structure. However, since conventional speech analysis methods (i.e., GMM parameter estimation) have been formulated for a narrow-band speech, they degrade the quality of synthetic speech. Moreover, a DNN-based TTS synthesis method using GMM-based approximation has not been formulated in spite of its excellent expressive ability. Therefore, we employ peak-picking-based initialization for full-band speech analysis to provide better initialization for iterative estimation of the GMM parameters. We introduce not only prediction error of GMM parameters but also reconstruction error of the spectral envelopes as objective criteria for training DNN. Furthermore, we propose a method for multi-task learning based on minimizing these errors simultaneously. We also propose a post-filter based on variance scaling of the GMM for our framework to enhance synthetic speech. Experimental results from evaluating our framework indicated that 1) the initialization method of our framework outperformed the conventional one in the quality of analysis-synthesized speech; 2) introducing the reconstruction error in DNN training significantly improved the synthetic speech; 3) our variance-scaling-based post-filter further improved the synthetic speech.

To improve the likability of speech, we propose a voice conversion algorithm by controlling the fundamental frequency (F0) and the spectral envelope and carry out a subjective evaluation. The subjects can manipulate these two speech parameters. From the result, the subjects preferred speech with a parameter related to higher brightness.

In this paper, we propose an image to sound mapping method. This technique treats an image as a spectrogram and maps it to a sound by taking inverse FFT of the spectrogram. Amplitude spectra of a speech signal are embedded to the spectrogram to give speech intelligibility for the mapped sound. Specifically, we hold amplitude spectra of a speech signal with strong power and embed the image brightness in other frequency bands. Holding amplitude spectra of a speech signal with strong power preserves a speech spectral envelope and improves the speech quality of the mapped sound. The amplitude spectra of the mapped sound with weak power represent the image brightness, and then the image is successfully reconstructed from the mapped sound. Simulation results show that the proposed method achieves sufficient speech quality.

In an OFDM communication system using quadrature amplitude modulation (QAM) signals, peak envelope powers (PEPs) of the transmitted signals can be well controlled by using QAM Golay complementary sequence pairs (CSPs). In this letter, by making use of a new construction, a family of new 16-QAM Golay CSPs of length N=2m (integer m≥2) with binary inputs is presented, and all the resultant pairs have the PEP upper bound 2N. However, in the existing such pairs from other references their PEP upper bounds can arrive at 3.6N when the worst case happens. In this sense, novel pairs are good candidates for OFDM applications.

Microwave mammography is a promising alternative to X-ray based imaging modalities, because of its small size, low cost, and cell-friendly exposure. More importantly, this modality enables the suppression of surface reflection clutter, which can be enhanced by introducing accurate surface shape estimations. However, near-field measurements can reduce the shape estimation accuracy, due to a mismatch between the reference and observed waveforms. To mitigate this problem, this study incorporates envelope-based shape estimation and finite-difference time-domain (FDTD)-based waveform correction with a fractional derivative adjustment. Numerical simulations based on realistic breast phantoms derived from magnetic resonance imaging (MRI) show that the proposed method significantly enhances the accuracy of breast surface imaging and the performance of surface clutter rejection.

Envelope tracking (ET) technology provides the potential for achieving high efficiency in power amplifiers (PAs) with high peak-to-average ratio (PAR) signals. Envelope amplifiers with high fidelity, high efficiency, and wide bandwidth are critical components for the widespread application of envelope tracking. This paper presents the design of a linear-assisted switching buck converter for use in an envelope amplifier. To effectively leverage the high efficiency of buck converters and the wide bandwidth capabilities of linear amplifiers, a parallel combination of these two devices is employed in this work. A novel current-sense constant-on-time (COT) controller is proposed to coordinate this hybrid power supply. The combination mainly enables the switching converter to provide the average power required by the PA with high efficiency, while the wideband linear amplifier provides a wide range of dynamic voltages. The technique improves the efficiency of the envelope amplifier, especially for applications requiring high PAR with wider bandwidth signals. Measurement of the envelope amplifier showed an efficiency of approximately 77% with 10 W output power using LTE downlink signals. The overall ET system was demonstrated by using a GaN PA. The measured average power-added efficiency of the amplifier reached above 45% for an LTE modulated signal with 20 MHz bandwidth and PAR of 8.0 dB, at an average output power of 5 W and gain of 10.1 dB. The measured normalized RMS error is below 2.1% with adjacent channel leakage ratio of -48 dBc at an offset frequency of 20 MHz.

This paper improves the family size of quadrature amplitude modulation (QAM) complementary sequences with binary inputs. By employing new mathematical description: B-type-2 of 4q-QAM constellation (integer q ≥ 2), a new construction yielding 4q-QAM complementary sequences (CSs) with length 2m (integer m ≥ 2) is developed. The resultant sequences include the known QAM CSs with binary inputs as special cases, and the family sizes of new sequences are approximately 22·2q-4q-1(22·2q-3-1) times as many as the known. Also, both new sequences and the known have the same the peak envelope power (PEP) upper bounds, when they are used in an orthogonal frequency-division multiplexing communication system.

In this letter, based on orthogonal Golay sequence sets and orthogonal matrices, general constructions of zero correlation zone (ZCZ) aperiodic complementary sequence (ZACS) sets are proposed. The resultant ZACSs have column sequence peak-to-mean envelop power ratio (PMEPR) of at most 2, and the parameters of the sequence sets are optimal with respect to the theoretical bound. The novel ZACS sets are suitable for approximately synchronized multi-carrier CDMA (MC-CDMA) communication systems.

Power amplifiers (PAs) are key components of mobile base stations. In the last decade, the power efficiency of PAs for 3G/4G mobile base stations has risen to over 50% as a result of employing efficiency enhancement techniques, such as Doherty, envelope tracking, and outphasing, in combination with GaN devices and digital predistortion. This trend has significantly contributed to reducing the power consumption of mobile base stations. Furthermore, digital transmitters using switch-mode PAs have the potential of breaking through the 70% efficiency level. Achieving this goal will require advances not only in circuitry but also in device technology. For active antenna systems of 5G mobile systems, ease of integration, as well as high efficiency, becomes important for PAs, and thus, Si-based devices will play a major role.

Controlling the peak-to-mean envelope power ratio (PMEPR) of orthogonal frequency-division multiplexed (OFDM) transmissions is a significant obstacle in many low-cost applications of OFDM. An coding approach proposed by H.R. Sadjadpour presents non-square M-QAM symbols as a combination of QPSK and BPSK signals when M=22n+1, and then uses QPSK and BPSK Golay (or Golay-like) sequences with a constant PMEPR to generate M-QAM sequences. This paper proposes a new scheme in which M-QAM sequences are generated by QPSK and BPSK sequences with variable PMEPRs. In other words, this new scheme is a general case of the existing approach. As a result, the code rate of the new sequence is significantly improved, while the upper bound of its PMEPR remains at a comparative level.

A non-photorealistic rendering method creates oil-film-like images, expressed with colorful, smooth curves similar to the oil films generated on the surface of glass or water, from color photo images. The proposed method generates oil-film-like images through iterative processing between a bilateral infra-envelope filter and an unsharp mask. In order to verify the effectiveness of the proposed method, tests using a Lena image were performed, and visual assessment of oil-film-like images was conducted for changes in appearance as the parameter values of the proposed method were varied. As a result of tests, the optimal value of parameters was found for generating oil-film patterns.

This paper proposes a method based on modulation transfer function (MTF) to restore the power envelope of noisy reverberant speech by using a Kalman filter with linear prediction (LP). Its advantage is that it can simultaneously suppress the effects of noise and reverberation by restoring the smeared MTF without measuring room impulse responses. This scheme has two processes: power envelope subtraction and power envelope inverse filtering. In the subtraction process, the statistical properties of observation noise and driving noise for power envelope are investigated for the criteria of the Kalman filter which requires noise to be white and Gaussian. Furthermore, LP coefficients drastically affect the Kalman filter performance, and a method is developed for deriving LP coefficients from noisy reverberant speech. In the dereverberation process, an inverse filtering method is applied to remove the effects of reverberation. Objective experiments were conducted under various noisy reverberant conditions to evaluate how well the proposed Kalman filtering method based on MTF improves the signal-to-error ratio (SER) and correlation between restored power envelopes compared with conventional methods. Results showed that the proposed Kalman filtering method based on MTF can improve SER and correlation more than conventional methods.

This paper describes an evaluation of a temporally stable spectral envelope estimator proposed in our past research. The past research demonstrated that the proposed algorithm can synthesize speech that is as natural as the input speech. This paper focuses on an objective comparison, in which the proposed algorithm is compared with two modern estimation algorithms in terms of estimation performance and temporal stability. The results show that the proposed algorithm is superior to the others in both aspects.

This paper proposes a new algorithm to encode the spectral envelope for G.729.1 more accurately. It applies the normalized least-mean- square (NLMS) algorithm to each subband energy of the modified discrete cosine transform (MDCT) in the time-domain alias cancellation (TDAC) of G.729.1. By utilizing the estimation error of subband energies by means of NLMS, allocated bit reduction for spectral envelope coding is achieved. The saved bits are then reused to improve the spectral envelope estimation and thus enhance the sound quality. Experimental results confirm that the proposed algorithm improves the sound quality under both clean and packet loss conditions.

To develop an envelope-tracking (ET) amplifier for next-generation cellular base stations, we propose a wideband envelope modulator, consisting of a linear-mode class-B amplifier and a switch-mode class-D amplifier. The function of the modulator is to track the envelope signal and supply voltage to an RF amplifier. To meet the requirements of a large-current and high-voltage supply that can handle a wideband signal, an “Alexander current-feedback amplifier topology” is applied to the linear-mode class-B amplifier. The Alexander topology not only boosts the voltage but also enhances the current capacity of a commercial high-speed operational amplifier (op-amp) by means of a push-pull stage with current mirrors and a buffer amplifier at the output of the op-amp. With this topology, a linear-mode amplifier can provide several-ampere-level current to a 11-Ω load. A prototype of the wideband envelope modulator is shown to achieve the efficiency of 71% with a 20-MHz WiMAX envelope signal at output power of 72W.

We present a multiband LTE SAW-less CMOS transmitter with source-follower-driven passive mixers, envelope-tracked RF-programmable gain amplifiers (RF-PGAs), and Marchand Baluns. A driver stage for passive mixers is realized by a source follower, which enables a quadrature modulator (QMOD) to achieve low noise performance at a 1.2 V supply and contributes to a small-area and low-power transmitter. An envelope-tracking technique is adopted to improve the linearity of RF-PGAs and obtain a better Evolved Universal Terrestrial Radio Access Adjacent Channel Leakage power Ratio (E-UTRA ACLR). The Marchand balun covers more frequency bands than a transformer and is more suitable for multiband operation. The proposed transmitter, which also includes digital-to-analog converters and a phase-locked loop, is implemented in a 65-nm CMOS process. The implemented transmitter achieves E-UTRA ACLR of less than -42 dBc and RX-band noise of less than -158 dBc/Hz in the frequency range of 700 MHz–2.6 GHz. These performances are good enough for multiband LTE and SAW-less operation.

Recently, dynamic power supply voltage techniques, such as an Envelope Elimination and Restoration power amplifier (EER-PA) or Envelope-Tracking Power amplifier (ET-PA), have been attracting much attention because they can maintain high efficiency in large back-off region [1]-[6]. The dynamic power supply voltage techniques cause strong nonlinearity compared to a conventional power amplifier, hence a memoryless Digital Predistortion (DPD) technique is indispensable for these efficiency enhancement techniques. However, the performance of the memoryless DPD is degraded due to the frequency response of the envelope amplifier in the dynamic power supply voltage techniques [7]-[9]. In this paper, we clarify the degradation mechanisms of the memoryless DPD for the EER-PA due to the frequency response of the envelope amplifier based on the results of two-tone tests, and propose an analytical model for improving the performance of the memoryless DPD developed for the EER-PA. In addition, a prototype EER-PA is developed and we demonstrate that the residual distortion of the developed EER-PA with conventional memoryless DPD algorithm is compensated by the new algorithm based on the proposed analytical model. In the two-tone test, third-order intermodulation distortion (IMD3) with a tone spacing from 100 kHz to 4 MHz is improvement by up to 25 dB by the memoryless DPD algorithm based on the proposed model. Measured adjacent channel leakage power ratio (ACPR) of the developed EER-PA is improved from -22.5 dBc to -42.5 dBc in the OFDM signal test with 1.08 MHz bandwidth.