We have proposed a mortar-shaped structure to improve response time and alignment uniformity of twisted vertically aligned (TVA) mode liquid crystal displays (LCDs) for high-contrast reflective color LCDs. From the results of the simulation, we clarified that response time, alignment uniformity and viewing angle range of TVA-mode LCDs were improved by controlling the liquid crystal alignment axis-symmetrically in each pixel.

We developed flexible liquid crystal devices using ultra-thin polyimide substrates and bonding polymer spacers, and discussed the effects of polymer spacer structure on the cell thickness uniformity of flexible LCDs. We clarified that the lattice-shaped polymer spacer is effective to stabilize the cell thickness by suppressing the flow of the liquid crystal during bending process.

We investigated the effects of a bending stress on the change in phase retardation of curved polycarbonate substrates and optical characteristics of flexible liquid crystal displays (LCDs). We clarified that the change in phase retardation was extremely small even for the substrates with a small radius of curvature, because bending stresses occurred in the inner and upper surfaces are canceled each other out. We compensated for the phase retardation of polycarbonate substrates by a positive C-plate and successfully suppressed light leakage in both non-curved and curved states. These results indicate the feasibility of high-quality flexible LCDs using polycarbonate substrates even in curved states.

A black mask (BM) is a layer used to improve the display quality by suppressing light leakage. In general, the BM is formed by a photolithography process. In this study, a novel technique for the fabrication of a quasi-black mask (q-BM) is proposed; the q-BM was composed of vertical and hybrid orientation areas, patterned by a separation coating technique using an electro-spray deposition method. Using our technique, the q-BM can be formed easily without the additional masks used for the BM.

We developed flexible LC devices using coat-debond polyimide substrates with a low birefringence and etched post spacers, and clarified that flexible LCDs using post spacers with small spacer distance have a high flexibility without degradation of the image quality. This result ensured the feasibility of flexible LCDs using coat-debond method.

To develop a flexible liquid crystal display (LCD) with a wide viewing angle range and high contrast ratio, we have proposed a flexible blue-phase LC device sustained by polymer walls inside the LC cell. We clarified that the polymer walls can maintain a constant cell gap and suppress the generation of alignment defects of the blue-phase LC in a bending state.

Optical compensation of flexible in-plane switching (IPS) mode liquid crystal display (LCD) using polycarbonate substrate with uniaxial optical anisotropy was achieved for wide viewing angle. We theoretically clarified that the slow axis of plastic substrate must be parallel to the absorption axis of polarizer and alignment direction of IPS mode LC. We successfully suppressed a light leakage in the dark state in a wide viewing angle range by fabricated device using uniaxial polycarbonate substrates. These results show that it is possible to realize a high quality flexible LCD using plastic substrates.

The TFT-LCD image has non-uniform brightness that is the major difficulty of finding the visible defect called Mura in the field. To facilitate Mura detection, background signal shading should level off and Mura signal must be amplified. In this paper, Mura signal amplification and background signal flattening method is proposed based on human visual system (HVS). The proposed DC normalized contrast sensitivity function (CSF) is used for the Mura signal amplification and polynomial regression (PR) is used to level off the background signal. In the enhanced image, tri-modal thresholding segmentation technique is used for finding Dark and White Mura at the same time. To select reliable defect, falsely detected invisible region is eliminated based on Weber's Law. By the experimental results of artificially generated 1-d signal and TFT-LCD image, proposed algorithm has novel enhancement results and can be applied to real automated inspection system.

This paper proposes a backlight module which drives multiple cold-cathode fluorescent lamps (CCFLs) with a current mirror technique to equalize the driving current for each lamp. We first adopt a half-bridge parallel-resonant inverter as the main circuit and use a single-input, multiple-output transformer to drive the multi-CCFLs. Next, we introduce current-mirror circuits to create a new current-sharing circuit, in which its current reference node and the parallel-connected multi-load nodes are used to accurately equalize all CCFLs' driving current. This will balance each lamp's brightness and, consequently, improve the picture display quality of the related liquid crystal display (LCD). This paper details the design concept for each component value with the assistance of an actual design example. The results of the example are examined with its actual measurements, which consequently verify the correctness of the proposed control strategy.

Low-profile inverter power supplies are increasingly required for backlight systems of liquid crystal displays (LCDs). A great deal of attention has been focused on the application of piezoelectric transformers (PTs) to such power supplies. To miniaturize PT inverters still further, PTs need to have sufficient high voltage-step-up-ratio, which can be achieved by a multilayered PT. First, this paper describes a method for simulating such performance using a distributed constant equivalent circuit model. The results of the simulation for a multilayered PT operated in the third order longitudinal vibration mode show that the resistance of internal electrodes causes the dominant loss factor. Next, a power inverter incorporating the multilayered PT was fabricated. This power inverter can be operated over a wide input DC voltage range from 7-20 V. Regarding a conventional inverter drive circuit, when input DC voltage range was extended, the inverter efficiency remarkably decreased. For the reason, we developed a new inverter circuit, which is equipped with an automatic drive voltage control circuit to maintain the drive voltage to the PT at a constant value. As a result, the fabricated power inverter exhibited more than 90% overall efficiency and 3.5 W output power, which is enough to light up a 12.1-inch color LCD. The maximum luminance efficiency on a light transmission plate of the backlight was as high as 30 cd/m2/W.

Voltage holding property of liquid crystal (LC) cell for long period was investigated and the experimantal results were analyzed using a microscopic model considered the movement of ions in LC layer. The time dependent voltage decay curve observed in the experiment, which is not driven by the analysis with the conventional equivalent circuit comprised of the capacitance and the resistance, can be well explained by the microscopic model.

We have realized excellent viewing angle characteristics for the π cell, by combining a discotic negative birefringence film, which has a hybrid alignment structure, and a positive a-plate. The negative birefringence of the film completely compensates the positive birefringence of the π cell liquid crystals in the dark-state. The roll of a c-plate, which should be accompanied by the a-plate to suppress the light leakage from crossed polarizer at oblique incident angles, was substituted for the vertically aligned component of the π cell liquid crystal. Taking into account the fast electrooptical response, which is one order faster than that of the twisted-nematic liquid-crystal display, the π cell is one of the most promising liquid-crystal-display modes.

A homeotropic liquid crystal display utilizing a liquid crystal with positive dielectric anisotropy, 13. 3" XGA TFT-LCD, has been fabricated. The rubbing-free device, appears black in the absence of electric field. When an electric field generated by interdigital electrodes is applied, a bend deformation of molecular director to the direction of the field occurs and thus the cell transmits light, showing brightness uniformity in all directions owing to the dual domainlike director configuration. With an addition of negative-birefringent film, this device shows excellent viewing angle characteristics.

We have studied the electro-optical properties in Polymer Network Liquid Crystal Displays which are composed of a three-dimensional polymer network formed in continuous liquid crystal layers prepared by photo-polymerization induced phase separation processes. In view of the behavior in the orientation of the liquid crystal molecule at the polymers surface, it can be clarified that the electro-optical properties are strongly governed by the polymer. By a combination of two different characteristics of the polymers with respect to a temperature dependence, a variation in the driving voltage for a temperature change can be improved.

Low-profile, miniaturized and highly efficient power inverters are required to light up backlights, which include cold cathode fluorescent lamps (CCFLs), in color liquid crystal displays (LCDs), replacing conventional power inverters with electromagnetic transformers. The object of this study is to actualize a power inverter to which a novel multilayered piezoelectric ceramic transformer operating in the third order longitudinal mode is applied. The piezoelectric transformer has a symmetrical structure in the lengthwise direction and its generating part operates in a piezoelectric stiffened mode in order to increase both energy conversion efficiency and power density. This transformer has great advantages. Namely, all the electronic terminals in this transformer can be connected at the vibration nodes of the transformer, which contributes to the guarantee of stable transformer performances at high power operation, and this transformer is superior in impedance matching against the backlight load at steady state, because the output impedance of this transformer is much lower than that of conventional Rosen type transformers. Then a power inverter with the transformer was fabricated. In this power inverter, a separately excited oscillation circuit was adopted to drive the transformer with high efficiency, and the transformer drive frequency was controlled by detecting the backlight current in order to adjust the backlight luminance properly. As a result, the fabricated power inverter exhibited more than 90% overall efficiency and 4. 5-W output power, which is enough power to light up a 9. 4 inch color LCD, including the stray capacitance loss resulting from CCFL mounting. The luminance value on a light transmission plate of the backlight was more than 2000 cd/m2.

A method is proposed for forming hillock-free aluminum-based alloy bus lines for active-matrix liquid-crystal displays (LCDs). Aluminum (Al)-based alloy films are deposited using an Al target containing boron (B) or nickel (Ni) in a sputtering ambient containing nitrogen. The Al-Ni films deposited using an Al target containing Ni showed excellent hillock resistance: virtually no hillock formation after thermal treatment at around 400 and no significant increase in resistivity. These films also showed good patternability with a simple wet etching: a smooth line edge and a gently tapered profile. These films are thus suitable for the bus lines of active matrices.

Amorphous silicon thin film transistors(a-Si TFTs) with a channel-etched structure were fabricated. The key technologies to realize these simple-process TFTs were 1) fabricating data lines and pixel electrodes of indium tin oxide(ITO); 2) carrying out tapered dry etching of plural layers of the a-Si and gate insulator silicon nitide; and 3) forming silicide layer to reduce the contact resistance between the phosphorousdoped a-Si and ITO. Excellent image quality, with a high contrast ratio of more than 100: 1, was obtained for video graphic array(VGA) mode TFT-LCDs using a dot inversion driving method. Furthermore, the transmission distribution was uniform with less than a 4.5% deviation on the whole display area although the ITO data line resistances were as large as 120 kΩ per line.

The characteristics of a-Si bottom-gate TFT test devices with several kinds of inorganic "quasi-black matrix," such as metal, semiconductor, and insulator, on the top were investigated for various black matrix(BM) resistivities. In the Ia-Vg characteristics, for a BM sheet resistance of about1 1012 Ω/, a high off current and large Vth shift were observed due to the back-gating effects when the BM is charged up. Accrding to the ac dynamic characteristics, there was almost no leakage due to the capacitive coupling between source and drain after 16.6 msec(one frame) when the BM sheet resistance was above 7 1013 Ω/ . It was found that hydrogenated amorphous silicon germanium(a-SiGe:H) film, which has enough optical density, with the sheet resistance above the order of 1014 Ω/ is a promising candidate for an inorganic BM on TFT array.

Super twisted nematic (STN) liquid crystal displays(LCDs) using spiral polymer aligned nematic (SPAN) liquid crystals have been achieved by photo-polymerization of some kinds of chiral monoacrylates in liquid crystalline hosts.The spiral polymer made of a chiral monoacrylate in STN LCD has effect to reduce the driving voltage without any disadvantages for the STN LCD. The relation of chemical structure of a chiral monoacrylate and nature of spiral polymer is discussed.

Transmittance distribution along a horizontal line in LCDs addressed by amorphous silicon TFTs was investigated using measurements and calculations. Nonuniformity of the distribution, in which the transmittance increased with increasing distance from the left edge of the LCD, was observed in a 10 inch diagonal TFT-LCD. The cause of the nonuniformity was attributed to the decrease in voltage drop due to the gate source parasitic capacitance and the increase in gate voltage fall time due to large line resistance, based on the measurements of voltage drops in TFT test elements and calculations considering the decrease in voltage drop. The distribution could be improved by reducing the line resistance and parasitic capacitance in the actual LCD.