Vibration characteristic of electromagnetic relay (EMR), including modal and frequency response are important for increasing operational reliability in mechanical environment. The switching contact system, as function execution component of EMR, is the important parts in this product. This paper presents a dynamic model of contact system by introducing Hertz contact theory, and discusses weakly nonlinear oscillation character. Quasilinear simulation analysis using by finite element analyzing software-NASTRAN is investigated. The factors affecting contact vibration characteristic are determined. Finally, theory analysis and simulation results are verified by the vibration test. The model starts from a typical contact system of EMR, but the approach can be applied to other switching electro-mechanical devices.

Experimental investigations on detection of terahertz radiation are presented. We used plasma wave instability phenomenon in nanometer Silicon field effect transistor. A 30 nm gate length transistor was illuminated by THz radiation at room temperature. We observe a maximum signal near to the threshold voltage. This result clearly demonstrates the possibility of plasma wave THz operation of these nanometer scale devices. The response was attributed to a non resonant detection. We also demonstrate the possibility to observe a resonant detection on the same devices.

The superconducting quantum interference device (SQUID) is a transducer that converts magnetic flux into voltage. Its range of linear conversion, however, is very restricted. To overcome its narrow dynamic range, a flux-locked loop (FLL) is used to feedback the output field to cancel the input field. This prevents the operating point of the SQUID from moving far away from the null point. In this paper, an emulator for the SQUID sensor and the feedback coil has been proposed. Magnetic coupling between the original field and the generated field by the feedback coil was emulated by electronic circuits. By using the emulator, FLL circuits can be analyzed and optimized without use of SQUID sensors. This is a useful feature, especially in the early stage of development of the MCG system when a magnetically shielded room or real SQUID sensors may not yet be available. The emulator may also be used as a test signal generator for multi-channel gain calibration and for system maintenance.

A microstrip phase shifter design that uses a reconfigurable metal pattern on the EBG ground plate is introduced. The EBG ground plate metal pattern contains a linear array of thin slots with switching devices loaded at the center. This design can vary the phase constant with minimum mismatch loss over a large frequency bandwidth. Several test ground plates without actual switching devices were used to verify the design concept.

This paper describes a two-dimensional clustering scheme-based analysis of audible noises induced at telephone terminals. To analyze EMI sources that cause telephone-audible noise, we use a self-organizing map, which provides a way to map high-dimensional data onto a two-dimensional domain. Also, in order to discriminate EMI sources without using particular resonance frequencies that have peaks in the frequency domain, we use the energy spectra of telephone-audible noises as input for training the self-organizing map. In applying this method in actual environments, we measured ten kinds of telephone-audible noises (due to Radio waves and cross-talk noises, etc.) and then derived their energy spectra for eight frequency bands: 1-250 Hz, 250-500 Hz, 500-1 kHz, 1 k-1.5 kHz, 1.5 k-2 kHz, 2 k-3 kHz, 3 k-4 kHz, and over 4 kHz. We visually confirmed that the measured telephone-audible noise data could be projected onto the map in accordance with their properties, resulting in a combined depiction of the composition of derived energy spectra in the frequency bands. The proposed method can deal with multi-dimensional parameters, projecting its results onto a two-dimensional space in which the projected data positions give us an effective depiction of EMI sources that cause disturbances at telephone terminals.

Magnetoencephalography (MEG) is a method to measure a magnetic field generated by electrical neural activity in a brain, and it plays increasingly important role in clinical diagnoses and neurophysiological studies. However, in MEG analysis, the estimation of the brain activity, of the electric current density distribution in a brain which is represented by current dipoles, is problematic. A spatial filter and subsequent reconstruction of the current density distribution estimated by the spatial filter (spatial filtered reconstruction: SFR) are proposed. The spatial filter is designed to be used without prior or temporal information. The proposed spatial filter ensures that it concentrates the current distribution around the activated sources in the conductor. The current distribution estimated by the spatial filter is reconstructed by multiple linear regression. Redundant current dipoles are eliminated, and the current distribution is optimized in the sense of the Mallows Cp statistic. Numerical studies are demonstrated and show successful estimation by SFR in multiple-dipole cases. In single-dipole cases with SNRs of 101 and more, the location of the true dipole was successfully estimated for about 80% of the simulations. The reconstruction with multiple linear regression corrected the location of the maximum current density estimated by the proposed spatial filtering. The dipole on the correct position contributes to more than 70% of the total dipoles in the estimated current distribution in those cases. These results show that the current distribution is effectively localized by SFR. We also investigate the differences among SFR, the LCMV (linearly constrained minimum variance) beamformer and the SAM (synthetic aperture magnetometry), the representatives of spatial filters in MEG analyses. It is indicated that spatial resolution is improved by avoiding dependence on temporal information.

This paper presents a modal-expansion analysis of the electromagnetically coupled coaxial dipole antenna. The analysis of the antenna problem is initially simplified using the even-odd mode excitation and then the resultant half structure is divided into two parts; one is the characterization of a coaxial feeding network and the other is the modeling of a sleeve monopole antenna driven by a coaxial line. The formally exact modal-expansion method is employed to analyze both parts. The analysis of the sleeve monopole antenna is facilitated by introducing a perfectly conducting boundary at a distance from the monopole's top end. The current distribution and input impedance of the electromagnetically coupled coaxial dipole antenna are obtained by finding expansion coefficients through enforcing the continuity of tangential field components across regional interfaces and cascading the two parts together. Numerical results for the coaxial dipole antenna's radiation characteristics are presented and discussed.

In this paper, the magnetic field properties and the dosimetry at intermediate frequency (21 kHz) for an induction heater are investigated with the coil model, which is prescribed as substitute source model in the European standard EN50366 (CENELEC). The accuracy of the magnetic field vectors and the values of the induced current density, which are achieved with the coil model, are compared with the results of a realistic model of the induction heater obtained from the equivalent source model. It is shown that the coil model coincides well for the magnitude of the magnetic field strength around the induction heater. On the other hand, the dominant field vector of the coil model differs significantly from the real induction heater, which leads to induced current densities in the body model which are three time larger. Owing to these results, the applicability of the coil model prescribed in the EN50366 is confirmed for the induction heater.

This paper proposes a parallel coupled microstrip bandpass filter (BPF) with ring Electromagnetic Bandgap (EBG) cells on the middle layer for spurious suppression. The ring EBG cells of the middle layer add a good stopband-rejection mode to the second harmonics of the parallel coupled microstrip BPF with suppression of over -50 dB, without affecting the center frequency and insertion loss of the original designed BPF. The design of ring EBG cells is presented and verified by the experimented results.

A new approach used to formulate to mixed-path propagation of surface wave is presented based on two main ingredients: the decomposition of electromagnetic fields and the introduction of equivalent electric (magnetic) currents adopted for convenience. The present method can be extended to obtain the corresponding results for the arbitrary incident wave excitation.

A new shielding evaluation setup for conductive O-rings is proposed. This setup consists of the holder with a groove to fix the O-ring position. There are two ways to apply O-rings in narrow gaps, cylinder-fixing and plane-fixing. With this holder shielding effects of the O-rings can be evaluated from 10 kHz to 1 GHz for both fixing types.

This letter proposes the thinnest hybrid EM wave absorber using a composite magnetic material, which can be applied to the 3 m semi anechoic chambers. We experimentally designed a new hybrid EM wave absorber of the wedge shape, which was made from the ferrite powder, the inorganic fiber and binder. As a result, the length of this absorber could be realized only 6 cm, which was ascertained having the nonflammable. The 3 m semi anechoic chamber is constructed in the size of L9 mW6 mH5.7 m using this absorber, and then the site attenuation is measured according to ANSI C63.4 in the frequency range of 30 MHz-1 GHz. As a result, the measured normalized site attenuation is obtained within 3 dB to the theoretical normalized site attenuation.

A free-space method is in wide spread use for the reflectivity measurement of electromagnetic wave absorbers (EMA) in VHF and UHF range. In the free-space method, the reflection levels from EMA and from the metal plate with same size as the EMA are measured, and the reflectivity is calculated from their ratio. The incident angle such as normal or oblique must be defined, and the polarization of electromagnetic (EM) wave must be specified to be TE, TM, or circularly-polarized mode. In this paper, a parallel EM wave beam method using dielectric lenses in front of horn antennas was studied experimentally. Electromagnetic wave absorption was measured with the vertical and the oblique incidence by using this parallel EM wave beam. This measurement system has following features:• It is compact because equiphase parallel EM wave beam was obtained in a short distance from the dielectric lens.• It requires no anechoic chamber because of little multi-reflection due to high directivity of parallel EM wave beam.• It allows a large oblique incident measurement by using high directive parallel EM wave beam.

The effect of a grounded conductive sheet placed over a PCB with a microstrip line on the electromagnetic noise shielding is discussed experimentally and with FDTD modeling. The grounding position of the sheet, which is connected with the ground plane of PCB, is changed. In results, the resonance frequency is shifted by the grounding position, and reducing the resonance of the input impedance should make a more effective shielding for EM noise radiation below 1 GHz.

Finding intracranial aneurysms plays a key role in preventing serious cerebral diseases such as subarachnoid hemorrhage. For detection of aneurysms, magnetic resonance angiography (MRA) can provide detailed images of arteries non-invasively. However, because over 100 MRA images per subject are required to cover the entire cerebrum, image diagnosis using MRA is very time-consuming and labor-intensive. This article presents a computer-aided diagnosis (CAD) system for finding aneurysms with MRA images. The principal components are identification of aneurysm candidates (= ROIs; regions of interest) from MRA images and estimation of a fuzzy degree for each aneurysm candidate based on a case-based reasoning (CBR). The fuzzy degree indicates whether a candidate is true aneurysm. Our system presents users with a limited number of ROIs that have been sorted in order of fuzzy degree. Thus, this system can decrease the time and the labor required for detecting aneurysms. Experimental results using phantoms indicate that the system can detect all aneurysms at branches of arteries and all saccular aneurysms produced by dilation of a straight artery in 1 direction perpendicular to the principal axis. In a clinical evaluation, performance in finding aneurysms and estimating the fuzzy degree was examined by applying the system to 16 subjects with a total of 19 aneurysms. The experimental results indicate that this CAD system detected all aneurysms except a fusiform aneurysm, and gave high fuzzy degrees and high priorities for the detected aneurysms.

Techniques of near-field magnetic measurement and their applications to EMC of digital equipment are described. Magnetic-field measurement near PCB or LSI is the mostly used technique to specify the source. This paper treats an example of board analysis by near-field magnetic measurement, the sensing mechanism and the structure of a loop probe, and a recent progress of this method and application. To establish appropriate design direction in high-speed and high-density packaging of electronic equipment, electromagnetic behavior in chip and package should be clarified. Expectation of development for measuring minute area is more and more increasing.

An inverse scattering problem of estimating the surface impedance for an inhomogeneous half-space is investigated. By virtue of the fact that the far field representation contains the spectral function of the scattered field, complex values of the function are estimated from a set of absolute values of the far field. An approximate function for the spectral function is reconstructed from the estimated complex values by the least-squares sense. The surface impedance is estimated through calculating the field on the surface of the half-space expressed by the inverse Fourier transform. Numerical examples are given and the accuracy of the estimation is discussed.

A new technique incorporating combinatorial deposition to develop thin-film phosphors by r.f. magnetron sputtering is demonstrated using subdivided powder targets. In comparison with development using conventional r.f. magnetron sputtering, the atomic ratios of Si and Ge as well as the Mn content in Zn2Si1-XGeXO4:Mn thin film phosphors could be more efficiently optimized in order to obtain the highest intensity in electroluminescent and photoluminescent emissions. High luminances of 11800 and 1536 cd/m2 were obtained in Zn2Si0.6Ge0.4O4:Mn thin-film electroluminescent devices fabricated under optimized conditions and driven at 1 kHz and 60 Hz, respectively.

Unwanted electromagnetic emission occurs due to the common-mode current on the cables entering a PC's metal enclosure and can be treated as wire antennas passing through the apertures of the enclosure. To reduce the emission, a stack of metal rings is suggested to be placed around the cable and external to the aperture, adopting the concept of a Coaxial Band-Stop Filter, for the first time. The influence of this novel structure on the common-mode current is examined in the FDTD-method frame work.

We demonstrate a novel fiber device exhibiting magnetic circular dichroism (MCD) and Faraday rotation in sharpened optical fibers coated with Fe. The degree of MCD was 0.68 in a magnetic field of 0.35 T and the Faraday rotation angle was as great as 110 degrees. Such great magneto-optical effect is due to optical near-field interactions in the sub-wavelength region, i.e., in the tip of the near-field fiber probe. These effects can be attributed to the large magnitude of the magneto optical coefficient of Fe.