Making up an electromagnetic wave simulator based on the FEM is tried, which may run on some widely used platforms by use of Java and a single commercial tool. Since the codes and configuration files to be created for this simulator are common, one can construct the simulator running on the platforms at the same time. Using this simulator, the transmission properties of two- and three-dimensional waveguide discontinuities in optical and microwave waveguides are analyzed, the inverse problem in material constant measurement is solved, and the computed results are presented including plots of the electric field distribution.

As the capacity of a personal computer and workstation increases rapidly, many electromagnetic simulators solving antenna problems are widely used. In this paper, the IE3D, FIDELITY and HFSS electromagnetic simulators, which are commercial software products, are applied to the analysis of built-in antennas for handsets in the vicinity of the human body. The IE3D, FIDELITY and HFSS electromagnetic simulators are based on the methods of moment, FDTD (Finite Difference Time Domain) and FEM (Finite Element Method), respectively. Firstly, basic characteristics including the human body's effect of a popular built-in antenna for handset such as PIFA (Planar Inverted-F Antenna) are obtained by the IE3D, FIDELITY and HFSS electromagnetic simulators, and calculated results are compared with measured results. Secondly, on the basis of newly considered design concepts for a handset antenna, a folded loop antenna for handset, which we have proposed in order to reduce the influence of the human body, is taken as an example of a balance-fed antenna and is analyzed theoretically and experimentally including the influence of the human body. In a result, calculated results by these three kinds of electromagnetic simulators are in good agreement with measured results and it is confirmed that these simulators are very effective in analyzing the handset antenna in the vicinity of the human body.

The boundary element method (BEM), a representative method of numerical calculation of electromagnetic wave scattering, has been used for solving boundary integral equations. Using BEM, however, we finally have to solve a linear system of L equations expressed by dense coefficient matrix. The floating-point operation is O(L2) due to a matrix-vector product in iterative process. Greengard-Rokhlin's fast multipole algorithm (GRFMA) can reduce the operation to O(L). In this paper, we describe GRFMA and its floating-point operation theoretically. Moreover, we apply the fast Fourier transform to the calculation processes of GRFMA. In numerical examples, we show the experimental results for the computation time, the amount of used memory and the relative error of matrix-vector product expedited by GRFMA. We also discuss the convergence and the relative error of solution obtained by the BEM with GRFMA.

In this paper, we proposed the doubly tapered electromagnetic periodic structure (DT-EPS) bandstop filters in coplanar waveguide (CPW) and cylindrical coplanar waveguide (CCPW). The DT-EPS bandstop filter not only can effectively improve the stopband rejection but also increase its bandwidth. In addition, this technique can significantly reduce the passband ripples compared with conventional case.

To develop ultra high density magnetic recording systems, a quasi-static system with a reciprocating medium motion against a stand still head was developed for a read/write tester. Double-layered perpendicular recording media and merged GMR heads assembled on a conventional head-gimbal assembly (HGA) were applied to evaluate the read/write performances. A smooth sliding contact motion was achieved, however, the head-to-medium spacing was varied depending on the head motion direction. The spacing in the reverse running direction of the conventional head slider seems to be smaller than that of the flying height in a high-speed spin stand. A merged ring head was suitable for perpendicular magnetic recording in the case of the reverse direction sliding.

A reactive sputtering method using an Electron-Cyclotron-Resonance (ECR) microwave plasma was used to deposit Ni-Zn ferrite thin-films for a soft magnetic backlayer of Co-containing spinel ferrite thin-film perpendicular magnetic recording (PMR) media. The Ni-Zn spinel ferrite thin-films with a preferential orientation of (100) and a relatively low coercivity of 15 Oe were obtained at a high deposition rate of 14 nm/min and at a temperature below 200 degrees C. Although post-annealing treatment in air at 200 degrees C was effective to decrease the coercivity of the Ni-Zn ferrite thin-films, the saturation magnetization and initial permeability decreased and the surface smoothness was deteriorated simultaneously. The Ni-Zn ferrite thin-films prepared by ECR sputtering are promising as the backlayer of the perpendicular magnetic recording medium, but further improvement is required in terms of the soft magnetic properties, the grain size and the surface roughness.

The segregation of non-magnetic phases such as borosilicate and Cr was investigated by crystallization behavior during the surface and bulk crystallization of Co-based amorphous alloys. The concentration of metalloids (B and Si) determined the extent of grain boundary segregation of borosilicate glass during surface crystallization. During the bulk crystallization of (Co75Cr25)0.8Si5B15 amorphous alloy, solute rejection of Cr resulted in the nucleation of Cr-deficient ferromagnetic crystals and non-magnetic σ-phase was subsequently precipitated along the grain boundary. These results show that crystallization process, i.e. nucleation and growth can be controlled to optimize the microstructure to reduce media noises in Co-based recording media.

We investigate the statistical features of both random- and chaos-based FM timing signals to ascertain their applicability to digital circuits and systems. To achieve such a goal, we consider both the case of single- and two-phase logic and characterize the random variable representing, respectively, the time lag between two subsequent rising edges or between two consecutive zero-crossing points of the modulated timing signal. In particular, we determine its probability density and compute its mean value and variance for cases which are relevant for reducing Electromagnetic emissions. Finally, we address the possible problems of performance degradation in a digital system driven by a modulated timing signal and to cope with this we give some guidelines for the proper choice of the statistical properties of the modulating signals.

In this work, micromagnetic simulations of writing and reading processes in a perpendicular system including a single pole head and recording media with soft underlayer (SUL) have been performed. The noise contribution from the recording layer increased with increasing grain size distribution of the recording layer but that from soft underlayer remained almost a constant at a given linear density. Details of the noise from the soft underlayer will be discussed. Also thermal decay over a long time scale of the recorded bits was investigated by the Langevin equation and the time-temperature scaling method. It was found that at the linear density of 1058 kfci narrower grain size distribution in the recording layer even in the same average grain size is very important in the point of thermal decay than expectation.

Co-containing ferrite thin-film/Mn-Zn ferrite thin-film double-layered perpendicular media were prepared using reactive ECR sputtering and magnetron sputtering methods, and their magnetic and structural properties and recording characteristics were studied. The Mn-Zn ferrite thin-film backlayer had saturation magnetization of 3.5 kG and coercivity of 60 Oe. Reproduced voltage for the Co-containing ferrite thin-film/Mn-Zn ferrite thin-film double-layered medium was about twice of that for the Co-containing ferrite single-layer medium.

As head-disk spacing is reduced, the effects caused by inter-molecular level interactions between head-slider and disk media are becoming a severe stability concern of head-slider's positioning in both flying height and track following directions. Therefore, there is a need to explore simple but effective methods for characterizing two dimensional (2D) stability. Ideally methods should be easy to implement in both the laboratory and in the quality control of disk drive and component manufacturing. A reading process based in-situ method is explored in this work. The method is simple and can effectively reveal the 2D stability of the head-slider in both laboratory and manufacturing environments. The results obtained also suggest that the observable sway mode vibration of the suspension can be excited earlier than the air-bearing vibration mode, when the flying height is reduced.

The tectonic activities that precede significant earthquakes release electromagnetic (EM) waves that can be used as earthquake precursors. We have been observing EM radiation in the ELF (extremely low frequency) band at about 40 observation stations in Japan for predicting significant earthquakes. The recorded signals contain, however, several noise components generated from the ionosphere, human activity, and so on. Most background noise in observed signal is attributed to lightning in the tropics. This paper proposes method based on PCA (principal component analysis) to extract signals from large data sets. The good performance of the proposed method is confirmed.

An analysis method based on the FD-TD and radiation mode expansion methods and its simulation tool are developed for calculating circuit characteristics and parameter values of passive MMIC (Monolithic Microwave Integrated Circuits) elements having multilayer structure. For straight multilayer microstrip lines and coplanar waveguides, it is possible to calculate characteristic impedance, effective permittivity, transverse field distribution of guided modes, etc. For various multilayer microstrip and coplanar waveguide elements, it is possible to calculate scattering parameters, radiated power, radiation patterns, etc. As an example of application of the present technique, effects of inclusion of lower permittivity layer in the substrate on transmission and radiation characteristics are investigated for right-angled microstrip bends.

So far, a lot of analyses have been performed on the edge-guide mode isolator with one short edge. However, the detailed characteristics such as the influence of shape of a metal strip and the thickness of a ferrite substrate have not been revealed. This paper clarifies the influence of the structure on the frequency response both experimentally and numerically. The numerical analysis is performed by the FDTD method. The numerical results indicate that the frequency response does not depend on the thickness of ferrite substrate but does on the shape of the metal strip. Furthermore, based on the numerical results, the experiment is carried out on the prototype isolator. All the results provide a theory of the optimum design on the isolator.

In this paper, we describe our study on a novel high-frequency magnetic field probe based both on the BiRIG rotation magnetization (RM) phenomenon and the third-generation optical probing scheme. First, we explain our experimental investigation on RF sensitivity and frequency response of the RM-based Faraday effect in a commercially available Bi-substituted rare-earth iron garnet plate. Second, we report on the implementation of fiber-optic magneto-optic (MO) probe heads with bandwidths of 10 GHz or broader, which have been brought about by careful arrangement of the magnetization axis of a single-domain crystal and the highly sensitive fiber-edge optical probing scheme. Third, we describe a few RF magnetic field distribution measurements carried out successfully over GHz-band microstrip line circuits. The results of the study imply the substantial potential of the present MO probe head for the RF current visualization.

In this study, the frequency and spatial properties of undesired electromagnetic radiation distribution around a simple printed circuit board (PCB) model, which only has the mismatching printed line (PL) and ground, are estimated. Finite difference time domain (FDTD) modeling is developed for the analysis space, which is 500 400 51 mm3 in size, around the PCB. As the driving clock pulse has a very wide frequency bandwidth, ranging from kHz to GHz, basic and precise investigation of the noise emission mechanism from the basic model is performed. The results of the magnetic field Hx on the PCB as determined by FDTD simulation, and those of the experiment, driven by a clock pulse, agree well. The results show that although this approach is basic and simple, it becomes clear that the frequency and spatial characteristics of the electric and magnetic field near the PCB are influenced by the wavelength of the frequency and appling the driving clock pulse, and the low-frequency component of the electromagnetic distribution around the PCB is larger than the high-frequency components. It is suggested that the low-frequency noise problem should be carefully considered.

As a new material, silver (Ag) coated fabric has been developed, and its use for shielding electromagnetic radiation is expected. In this paper, seven kinds of Ag coated fabrics, woven, knitted and nonwoven by Ag coated fibers, are prepared, and placed over a PCB with a microstrip line, which is used as a noise source. By measuring the input impedance of the microstrip line, the distance between the PCB and the fabric is fixed to 8 mm to reduce the coupling paths. The shielding effect SE of those fabrics was compared by measuring the magnetic near-field with a small shielded-loop probe. In the results, the resonance frequency is dependent on the fabric's length, as well as the case of a copper sheet. Comparing the texture, the SE of woven and nonwoven fabrics is larger than the knitted fabric. Comparing with the copper sheet, the SE of the fabrics is smaller below 200 MHz, but elsewhere is almost the same.

We have thoroughly investigated the effect of on-chip decoupling capacitors on the simultaneous switching noise (SSN) and the radiated emission. Furthermore, we have successfully demonstrated an efficient design method for on-chip decoupling capacitors on an 8-bit microcontroller without increasing the die size, which results in more than 10 dB of suppressed radiated emission.

To estimate the electromagnetic noise radiated from a printed circuit board (PCB) driven by a switching device, the finite difference time domain (FDTD) simulation method implementing the switching transistor is developed. The electric and magnetic field distributions on the signal line driven by a switching transistor are calculated or measured. These calculated and measured results show good agreement. The electric and magnetic field noises at typical impedance conditions modeled for the switching condition, i.e., the ON or OFF state of the transistor, are estimated by the FDTD calculation. The variation of the radiation noise when the switching transistor is turned ON or OFF is large at 216 MHz, whose input impedance of the signal line is small. It is speculated that the noise radiation at the 10 Ω signal source impedance condition that is modeled for the ON condition shows good agreement with the noise distributions at the driving condition.

In testing the possible biological effects of electromagnetic exposure from cellular telephones in small animals such as mice, it is essential to realize a highly localized head exposure as close as possible to that due to cellular telephones in humans. In this study, a 1.5GHz exposure setup was developed which has a highly localized specific absorption rate (SAR) of 2W/kg in the mouse brain and a low whole-body averaged SAR of 0.27W/kg. The low whole-body averaged SAR was realized by using a flexible magnetic sheet attachment on the mouse holder. Its validity has been carefully examined by both numerical simulation with an anatomically based mouse model and experimental simulation with a solid mouse phantom. Good agreement was obtained between the numerical and experimental results, which confirmed the effectiveness of the magnetic sheet attachment to the mouse holder.