In lossy image/video encoding, there is a compromise between the number of bits and the extent of distortion. Optimizing the allocation of bits to different sources, such as frames or blocks, can improve the encoding performance. In intra-frame encoding, due to the dependency among macro blocks (MBs) introduced by intra prediction, the optimization of bit allocation to the MBs usually has high complexity. So far, no practical optimal bit allocation methods for intra-frame encoding exist, and the commonly used method for intra-frame encoding is the fixed-QP method. We suggest that the QP selection inside an image/a frame can be optimized by aiming at the constant perceptual quality (CPQ). We proposed an iteration-based bit allocation scheme for H.264/AVC intra-frame encoding, in which all the local areas (which is defined by a group of MBs (GOMBs) in this paper) in the frame are encoded to have approximately the same perceptual quality. The SSIM index is used to measure the perceptual quality of the GOMBs. The experimental results show that the encoding performance on intra-frames can be improved greatly by the proposed method compared with the fixed-QP method. Furthermore, we show that the optimization on the intra-frame can bring benefits to the whole sequence encoding, since a better reference frame can improve the encoding of the subsequent frames. The proposed method has acceptable encoding complexity for offline applications.

Compared to the traditional functional dependency (FD), the extended conditional functional dependency (CFD) has shown greater potential for detecting and repairing inconsistent data. CFDMiner is a widely used algorithm for mining constant-CFDs. But the search space of CFDMiner is too large, and there is still room for efficiency improvement. In this paper, an efficient pruning strategy is proposed to optimize the algorithm by reducing the search space. Both theoretical analysis and experiments have proved the optimized algorithm can produce the consistent results as the original CFDMiner.

Chen proposed an image quality assessment method to evaluate image quality at a ratio of noise in an image. However, Chen's method had some drawbacks that unnoticeable noise is reflected in the evaluation or noise position is not accurately detected. Therefore, in this paper, we propose a new image quality measurement scheme using the mean-centered WLNI (Weber's Law Noise Identifier) and the saliency map. The experimental results show that the proposed method outperforms Chen's and agrees more consistently with human visual judgment.

The tree-based routing approach has been known as an efficient method for node mobility management and data packet transmission between two long-distance parties; however, its parameter adjustment must balance control overhead against the convergence speed of topology information according to node mobility. Meanwhile, location-based routing works more efficiently when the distance between the source and destination is relatively short. Therefore, this paper proposes a roadside unit (RSU) based hybrid routing protocol, called RSU-HRP that combines the strengths of both protocols while offsetting their weaknesses. In RSU-HRP, the tree construction is modified to take into account the link and route quality to construct a robust and reliable tree against high node mobility, and an optimized broadcast algorithm is developed to reduce control overhead induced by the advertisement message periodically sent from a roadside unit. In addition, the two routing methods are selectively used based on the computed distance in hops between a source and a destination. Simulation results show that RSU-HRP far outperforms TrafRoute in terms of packet delivery ratio, end-to-end delay, and control overhead in both Vehicle-to-Infrastructure and Vehicle-to-Vehicle communication models.

Reduced-reference (RR) image quality assessment (IQA) algorithm aims to automatically evaluate the distorted image quality with partial reference data. The goal of RR IQA metric is to achieve higher quality prediction accuracy using less reference information. In this paper, we introduce a new RR IQA metric by quantifying the difference of discrete cosine transform (DCT) entropy features between the reference and distorted images. Neurophysiological evidences indicate that the human visual system presents different sensitivities to different frequency bands. Moreover, distortions on different bands result in individual quality degradations. Therefore, we suggest to calculate the information degradation on each band separately for quality assessment. The information degradations are firstly measured by the entropy difference of reorganized DCT coefficients. Then, the entropy differences on all bands are pooled to obtain the quality score. Experimental results on LIVE, CSIQ, TID2008, Toyama and IVC databases show that the proposed method performs highly consistent with human perception with limited reference data (8 values).

The role of an optical low-pass filter (OLPF) in a digital still camera is to remove the high spatial frequencies that cause aliasing, thereby enhancing the image quality. However, this also causes some loss of detail. Yet, when an image is captured without the OLPF, moiré generally appears in the high spatial frequency region of the image. Accordingly, this paper presents a moiré reduction method that allows omission of the OLPF. Since most digital still cameras use a CCD or a CMOS with a Bayer pattern, moiré patterns and color artifacts are simultaneously induced by aliasing at high spatial frequencies. Therefore, in this study, moiré reduction is performed in both the luminance channel to remove the moiré patterns and the color channel to reduce color smearing. To detect the moiré patterns, the spatial frequency response (SFR) of the camera is first analyzed. The moiré regions are identified using patterns related to the SFR of the camera and then analyzed in the frequency domain. The moiré patterns are reduced by removing their frequency components, represented by the inflection point between the high-frequency and DC components in the moiré region. To reduce the color smearing, color changing regions are detected using the color variation ratios for the RGB channels and then corrected by multiplying with the average surrounding colors. Experiments confirm that the proposed method is able to reduce the moiré in both the luminance and color channels, while also preserving the detail.

With the growth of cloud-based services, cloud data centers are experiencing large growth. A key component in a cloud data center is the network technology deployed. In particular, Ethernet technology, commonly deployed in cloud data centers, is already envisioned for 10 Tbps Ethernet. In this paper, we study and analyze the makespan, workload execution times, and virtual machine migrations as the network speed increases. In particular, we consider homogeneous and heterogeneous data centers, virtual machine scheduling algorithms, and workload scheduling algorithms. Results obtained from our study indicate that the increase in a network's speed reduces makespan and workloads execution times, while aiding in the increase of the number of virtual machine migrations. We further observed that the number of migrations' behaviors in relation to the speed of the networks also depends on the employed virtual machines scheduling algorithm.

In the case of a disaster such as an earthquake or a tsunami, the city, town, and village administration usually issues an evacuation advisory and other information through the Outdoor Public Address Speakers for the disaster reduction broadcasting system covering its area of jurisdiction. However, in areas those have previous experience of a disaster, people frequently voice the lack of audibility of the disaster reduction broadcast. In this research, we conducted a questionnaire survey on the residents in the central area of Ishinomaki City, Miyagi Prefecture, who are the victims of the Great East Japan Earthquake Disaster, on the audible quality of outdoor public address (PA) speakers of the disaster reduction broadcasting system so as to understand the current state of such broadcasts and to propose ideal methods of sending and receiving information at the time of a future disaster.

Selective visual attention is an integral mechanism of the human visual system that is often neglected when designing perceptually relevant image and video quality metrics. Disregarding attention mechanisms assumes that all distortions in the visual content impact equally on the overall quality perception, which is typically not the case. Over the past years we have performed several experiments to study the effect of visual attention on quality perception. In addition to gaining a deeper scientific understanding of this matter, we were also able to use this knowledge to further improve various quality prediction models. In this article, I review our work with the aim to increase awareness on the importance of visual attention mechanisms for the effective design of quality prediction models.

The emerging three-dimensional (3D) technology is considered as a promising solution for achieving better performance and easier heterogeneous integration. However, the thermal issue becomes exacerbated primarily due to larger power density and longer heat dissipation paths. The thermal issue would also be critical once FPGAs step into the 3D arena. In this article, we first construct a fine-grained thermal resistive model for 3D FPGAs. We show that merely reducing the total power consumption and/or minimizing the power density in vertical direction is not enough for a thermal-aware 3D FPGA backend (placement and routing) flow. Then, we propose our thermal-aware backend flow named TherWare considering location-based heat balance. In the placement stage, TherWare not only considers power distribution of logic tiles in both lateral and vertical directions but also minimizes the interconnect power. In the routing stage, TherWare concentrates on overall power minimization and evenness of power distribution at the same time. Experimental results show that TherWare can significantly reduce the maximum temperature, the maximum temperature gradient, and the temperature deviation only at the cost of a minor increase in delay and runtime as compared with present arts.

The present study proposes a method for estimation of subjective image quality, for combinations of display physical factors, based on the Mahalanobis-Taguchi system in the field of quality engineering. The proposed method estimates subjective image quality by the estimated equation based on the Mahalanobis-Taguchi System and subjective evaluation experiments using the method of successive categories for images of which parameters are combinations of gamma, maximum luminance and minimum luminance. The estimated image quality is in good agreement with the experimental subjective image quality.

Perceptually optimized missing texture reconstruction via neighboring embedding (NE) is presented in this paper. The proposed method adopts the structural similarity (SSIM) index as a measure for representing texture reconstruction performance of missing areas. This provides a solution to the problem of previously reported methods not being able to perform perceptually optimized reconstruction. Furthermore, in the proposed method, a new scheme for selection of the known nearest neighbor patches for reconstruction of target patches including missing areas is introduced. Specifically, by monitoring the SSIM index observed by the proposed NE-based reconstruction algorithm, selection of known patches optimal for the reconstruction becomes feasible even if target patches include missing pixels. The above novel approaches enable successful reconstruction of missing areas. Experimental results show improvement of the proposed method over previously reported methods.

Adherence to coding conventions during the code production stage of software development is essential. Benefits include enabling programmers to quickly understand the context of shared code, communicate with one another in a consistent manner, and easily maintain the source code at low costs. In reality, however, programmers tend to doubt or ignore the degree to which the quality of their code is affected by adherence to these guidelines. This paper addresses research questions such as “Do violations of coding conventions affect the readability of the produced code?”, “What kinds of coding violations reduce code readability?”, and “How much do variable factors such as developer experience, project size, team size, and project maturity influence coding violations?” To respond to these research questions, we explored 210 open-source Java projects with 117 coding conventions from the Sun standard checklist. We believe our findings and the analysis approach used in the paper will encourage programmers and QA managers to develop their own customized and effective coding style guidelines.

Digital video signals are subject to several distortions due to compression processes, transmission over noisy channels or video processing. Therefore, the video quality evaluation has become a necessity for broadcasters and content providers interested in offering a high video quality to the customers. Thus, an objective no-reference video quality assessment metric is proposed based on the sigmoid model using spatial-temporal features weighted by parameters obtained through the solution of a nonlinear least squares problem using the Levenberg-Marquardt algorithm. Experimental results show that when it is applied to MPEG-2 streams our method presents better linearity than full-reference metrics, and its performance is close to that achieved with full-reference metrics for H.264 streams.

Current mobile communication terminals are equipped with multiple RF circuits that cover all frequency bands assigned for the communication. In order to make efficient use of frequency spectrum and to reduce circuits in a terminal, a low-loss reconfigurable RF filter is necessary to flexibly change RF frequencies. In this paper, a new reconfigurable bandpass filter (BPF) having eight-frequency (three-bit) selection capability is proposed. It employs branch-line switched type variable resonators that provide low insertion loss. One of the design issues is how to control pass bandwidths among selectable frequencies. In order to analyze the bandwidth variation of the reconfigurable BPF, we calculate the changes of external Q and coupling coefficients. It is shown that the inductive coupling design can achieve less variation of bandwidth for the reconfigurable BPF, compared with commonly used capacitive coupling design. A prototype BPF on a printed circuit board with high dielectric constant substrate has been fabricated and evaluated in 2 GHz bands. It presents performance very close to the design results with respect to insertion loss, center frequency and passband bandwidth. Low insertion loss of less than 1 dB is achieved among the eight frequencies.

State-of-the-art background subtraction and foreground detection methods still face a variety of challenges, including illumination changes, camouflage, dynamic backgrounds, shadows, intermittent object motion. Detection of foreground elements via the robust principal component analysis (RPCA) method and its extensions based on low-rank and sparse structures have been conducted to achieve good performance in many scenes of the datasets, such as Changedetection.net (CDnet); however, the conventional RPCA method does not handle shadows well. To address this issue, we propose an approach that considers observed video data as the sum of three parts, namely a row-rank background, sparse moving objects and moving shadows. Next, we cast inequality constraints on the basic RPCA model and use an alternating direction method of multipliers framework combined with Rockafeller multipliers to derive a closed-form solution of the shadow matrix sub-problem. Our experiments have demonstrated that our method works effectively on challenging datasets that contain shadows.

The IEEE 802.11 wireless LAN (WLAN) is based on carrier sense multiple access with collision avoidance (CSMA/CA) protocol. CSMA/CA uses a backoff mechanism to avoid collisions among stations (STAs). One disadvantage of backoff mechanisms is that STAs must wait for some period of time before transmission, which degrades spectral efficiency. Moreover, a backoff algorithm cannot completely avoid collisions. We have proposed a novel medium access control (MAC) scheme called the visual recognition-based medium access control (VRMAC) scheme, which uses an LED-camera communication technique. STAs send media-access request messages by blinking their LEDs in VRMAC scheme. An access point (AP) receives the messages via its camera, and then allocates transmission opportunities to the STAs by transmitting control frames. Since the transmission rate of the LED-camera communication is lower than WLAN transmission, the delay of access requesting causes and it could decrease the system throughput of the VRMAC system based WLAN. We reveal the effect of the delay for TCP flows and propose enhanced access procedures to eliminate the effect of the delay. Our simulation results demonstrate that VRMAC scheme increases the system throughput in UDP and TCP traffic. Moreover, the scenario-based evaluations reveal that VRMAC scheme also decreases the session delay which is a metric of quality of experience (QoE) for TCP applications.

In this letter, we propose a new intra-field deinterlacing algorithm based on an edge dependent weighted filter (EDWF). The proposed algorithm consists of three steps: 1) calculating the gradients of three directions (45°, 90°, and 135°) in the local working window; 2) achieving the weights of the neighboring pixels by exploiting the edge information in the pixel gradients; 3) interpolating the missing pixel using the proposed EDWF interpolator. Compared with existing deinterlacing methods on different images and video sequences, the proposed algorithm improves the peak signal-to-noise-ratio (PSNR) while achieving better subjective quality.

Support of incoming traffic differentiation and Quality of Service (QoS) assurance is very important for the development of high performance packet switches, capable of separating traffic flows. In our previous paper, we proposed the implementation of two buffers at each crosspoint of a crossbar fabric that leads to the Dual Crosspoint Queued (DCQ) switch. Inside DCQ switch, one buffer is used to store the real-time traffic and the other for the non-real-time traffic. We also showed that the static priority algorithms can provide the QoS only for the real-time traffic due to their greedy nature that gives the absolute priority to that type of traffic. In order to overcome this problem, in our paper we propose the DCQ switch with the Largest Weighted Occupancy First scheduling algorithm that provides the desired QoS support for both traffic flows. Detailed analysis of the simulation results confirms the validity of proposed solution.

The current development of video quality assessment algorithms suffers from the lack of available video sequences for training, verification and validation to determine and enhance the algorithm's application scope. The Joint Effort Group of the Video Quality Experts Group (VQEG-JEG) is currently driving efforts towards the creation of large scale, reproducible, and easy to use databases. These databases will contain bitstreams of recent video encoders (H.264, H.265), packet loss impairment patterns and impaired bitstreams, pre-parsed bitstream information into files in XML syntax, and well-known objective video quality measurement outputs. The database is continuously updated and enlarged using reproducible processing chains. Currently, more than 70,000 sequences are available for statistical analysis of video quality measurement algorithms. New research questions are posed as the database is designed to verify and validate models on a very large scale, testing and validating various scopes of applications, while subjective assessment has to be limited to a comparably small subset of the database. Special focus is given on the principles guiding the database development, and some results are given to illustrate the practical usefulness of such a database with respect to the detailed new research questions.