Wireless personal area networks (WPANs) will play an important role in next-generation communication networks. Currently, two technologies are being considered for the physical layer of WPANs, based on the two ultra wideband (UWB) standards, namely, multiband orthogonal frequency division multiplexing (MB-OFDM) UWB and direct-sequence (DS) UWB. The coexistence issue of these two types of WPANs in the same coverage area, raises new issues and introduces new problems which should be dealt with to avoid performance degradation. In particular, efficient radio resource management (RRM) in such environments is challenging. Indeed, the coexistence of heterogenous UWB based WPANs (UPANs) has an ad hoc nature, which requires RRM approaches that are different from traditional infrastructure-based ones. In this paper, we propose new algorithms for two RRM modules in heterogeneous UPANs, namely, radio access technology (RAT) selection and vertical handoff (VHO). To improve the overall performance of the system, our design considers possible narrowband interference (NBI) in the environment as well as the link outage probability, in the decision process. We also provide an analytical model based on a 4D Markov process to study the system in equilibrium and derive the performance metrics, namely, the new-call and handoff-call blocking probabilities, throughput and average carried traffic. Numerical results and comparisons show that our design achieves enhanced performance in terms of throughput and grade of service (GoS).

In recent years, heterogeneous cellular network (HetNet) topology has been attracting much attention. HetNet, which is a network topology with low power base stations installed inside the cell range of conventional macrocells, can realize network capacity enhancement through the effects of macrocell offloading and cell shrinkage. Due to the heterogeneity nature of HetNet, network designers should carefully consider about the interference management, resource allocation, user association and cell range expansion. These issues have been well studied in recent literatures. However, one of the important problems which has not been well investigated in conventional works is the base station (BS) deployment problem in HetNet. This paper investigates the optimal pico base station deployment in heterogeneous cellular networks especially with the existence of hotspots. In this paper, pico BS locations are optimized together with other network parameters including spectrum splitting ratio and signal-to-interference-noise ratio (SINR) bias for cell range expansion to maximize the total system rate, by considering two spectrum allocation strategies, i.e. spectrum overlapping and spectrum splitting. Numerical results show that the optimized pico BS locations can improve the system rate, the average user rate and outage user rate in HetNet with hotspots.

In this paper, we consider a multi-cell cognitive radio network (CRN), which overlays a multi-cell primary network. To manage the coexistence, a primary-willingness based coexistent architecture and a novel intra-cell spectrum overlay and inter-cell spectrum underlay sharing method are proposed. In the system, primary base stations will broadcast pilot signals and interference margins to assist the CRN for interference channel evaluation and power control. Subject to the interference margins imposed by the primary network, we define a utility (payoff) function that can represent the secondary system performance while taking into account the co-channel interference among secondary cells. A distributed resource allocation scheme is devised to guarantee the primary performance, and at the same time, maximize the secondary utility without any cooperation among cognitive base stations (CBS). Quality of Service among users is also considered by the scheme such that the instantaneous data rate for each secondary user is larger than a given minimum rate. The resource allocation problem can be decomposed into two subproblems: subchannel allocation and distributed power allocation game (DPAG). We prove that there exists a Nash equilibrium in the DPAG and the equilibrium is unique. Moreover, the DPAG is also Pareto optimal in some constrained environments, that is, no CBS can further improve its performance without impairing others. The proposed algorithm turns out to converge to an equilibrium within a small number of iterations.

We present a multiband LTE SAW-less CMOS transmitter with source-follower-driven passive mixers, envelope-tracked RF-programmable gain amplifiers (RF-PGAs), and Marchand Baluns. A driver stage for passive mixers is realized by a source follower, which enables a quadrature modulator (QMOD) to achieve low noise performance at a 1.2 V supply and contributes to a small-area and low-power transmitter. An envelope-tracking technique is adopted to improve the linearity of RF-PGAs and obtain a better Evolved Universal Terrestrial Radio Access Adjacent Channel Leakage power Ratio (E-UTRA ACLR). The Marchand balun covers more frequency bands than a transformer and is more suitable for multiband operation. The proposed transmitter, which also includes digital-to-analog converters and a phase-locked loop, is implemented in a 65-nm CMOS process. The implemented transmitter achieves E-UTRA ACLR of less than -42 dBc and RX-band noise of less than -158 dBc/Hz in the frequency range of 700 MHz–2.6 GHz. These performances are good enough for multiband LTE and SAW-less operation.

A novel tunneling field-effect transistor (TFET) featuring the sigma-shape embedded SiGe sources and recessed channel is proposed. The gate facing the source effectively focuses the E-field at the tip of the source and eliminates the gradual turn-on issue of planar TFETs. The fabrication scheme modified from the state-of-the-art 45 nm/32 nm CMOS technology flows provides a unique benefit in the co-integrability and the control of ID-VGS characteristics. The feasibility is verified with TCAD process simulation of the device with 14 nm of the gate dimension. The device simulation shows 5-order change in the drain current with a gate bias change less than 300 mV.

A smart meter, a component of smart grid systems, has low computational capability. This is in contrast to data collection units (DCUs) and meter data management servers (MDMSs). In this study, we propose a lightweight signature scheme and an authentication and report protocol that can reduce computational overhead and facilitate efficient operation of these three components in smart grid systems. The proposed signature scheme, called the linear map digital signature scheme (LMDSS), uses properties of linear maps and matrix operations; hence, it has low computational requirements. The proposed protocol is a delegation-based authentication protocol that uses an intermediate node, DCU. Using the proposed protocol, authentication of a DCU can be completed by a hash function. To evaluate the performance of the scheme and protocol, we implemented signature schemes, ours and others, and simulated the proposed protocol to obtain analytical results. We also proved that the scheme is secure by using a random oracle and analyzing the security of the protocol based on possible attack scenarios.

Low-complexity joint subcarrier and power allocation is considered. The applied criterion is to minimize the transmission power while satisfying the users' rate requirements. Subcarrier and power allocation are separately applied. Fixed spectrum efficiency is assumed to simplify the subcarrier allocation. We show that under fixed spectrum efficiency, power allocation can be obtained by solving some sets of linear equations. Simulation result shows the effectiveness of the proposed algorithm.

In this paper, we study the problem of joint resource allocation in the two-way relay system, where a pair of multi-antenna users wish to exchange information via multi-antenna amplify-and-forward relay under orthogonal frequency-division multiplexing (OFDM) modulation. We formulate a sum-rate maximization problem subject to a limited power constraint for each user and relay. Our resource allocation strategy aims at finding the best pairing scheme and optimal power allocation over subchannels in frequency and space domains. This turns out to be a mixed integer programming problem. We then derive an asymptotically optimal solution though the Lagrange dual decomposition approach. Finally, simulation results are provided to demonstrate the performance gain of the proposed algorithms.

For a development of energy harvesting system, the fact of radio waves and ambient RF (Radio Frequency) sources, including passive devices along with novel circuits, are very closely related to mobile charging devices and energy storage system. The use of schottky diode and voltage multiplier circuits to express on the ambient RF sources surrounding the system is one way that has seen a sudden rise in use for energy harvesting. Practically speaking, the RF and ambient sources can be provided by active and passive devices such as inductors, capacitors, diode, etc. In this paper, we present a schottky based voltage multiplier circuits for mobile charging device which integrate the power generation module with radio wave generation module. We also discuss that multi-stage schematic, e.g., three-stage schottky diode based voltage multiplier circuits, for a continuing effort on energy harvesting system.

Modern field programmable gate arrays (FPGAs) with heterogeneous resources are partially reconfigurable. Existing methods of reconfiguration-aware floorplanning have limitations with regard to homogeneous resources; they solve only a part of the reconfigurable problem. In this paper, first, a precise model for partially reconfigurable FPGAs is formulated, and then, a two-phase floorplanning approach is presented. In the proposed approach, resource distribution is taken into consideration at all times. In the first step, a resource-aware insertion-after-remove perturbation is devised on the basis of the multi-layer sequence pair constraint graphs, and resource-aware slack-based moves (RASBM) are made to satisfy resource requirements. In the second step, a resource-aware fixed-outline floorplanner is used, and RASBM are applied to pack the reconfigurable regions on the FPGAs. Experimental results show that the proposed approach is resource- and reconfiguration-aware, and facilitates stable floorplanning. In addition, it reduces the wire-length by 4–28% in the first step, and by 12% on average in the second step compared to the wire-length in previous approaches.

This paper first formulates the optimal instantaneous resource allocation, including path selection, power allocation and subchannel scheduling with proportional fairness in MIMO, OFDMA and relay-enhanced network. The joint optimization problem is a NP-hard one with non-linear constraints. To simplify this problem, we first propose a water-filling method named 'CP-AP w PF' to adaptively allocate power only among transmitting antennas. Then, a modified iterative water-filling algorithm named 'AP-AP w PF' is proposed to achieve adaptive power allocation on each subchannel by using the Jensen's inequality. Simulation shows that 'AP-AP w PF' algorithm improves the throughput for cell-edge users, and achieve a tradeoff between maximizing system throughput and assuring individual QoS.

In OFDM-based cognitive radio systems, due to the out-of-band leakage from the secondary transmission, the interference to primary users must be considered in order to guarantee the quality of service of the primary transmission. For multiuser cognitive radio systems, there exist two crucial issues in resource allocation: fairness and efficiency, in order to balance the two issues, we proposed a new utility-based cross-layer resource allocation algorithm, which can not only control the interference to primary users caused by secondary users, but also balance the spectral efficiency and fairness among cognitive users. Further, the optimal NP-hard resource allocation problem in multiuser OFDM-based systems is reduced to the sub-optimal solution by dividing the original problem into the subcarrier allocation problem and the power allocation problem. It is shown that the proposed algorithm can obtain the best performance in terms of the average rate or the utility among existing algorithms, and at the same time, all the users obtain fair resource allocation.

A direction-of-arrival estimation (DoA) scheme that uses a uniform circular array (UCA) is proposed for near-field sources, where multiple pairs-of-subarrays exist with central symmetry. First, multiple generalized ESPRIT (G-ESPRIT) spectrums are obtained by applying the conventional G-ESPRIT algorithm to each of multiple pairs-of-subarrays. Second, a parallel spectrum is found by adding up the reciprocals of these G-ESPRIT spectrums and taking the reciprocal of the total. The locations of peaks in the parallel spectrum give the DoAs being estimated. When a DoA approaches the translation direction of two subarrays, the conventional G-ESPRIT spectrum is broken by a false peak. Since the translation directions of pairs-of-subarrays are different from each other, the false peak, due to the DoA approaching one of translation directions, does not exist simultaneously in all G-ESPRIT spectrums. The parallel concatenation of the spectrums suppresses the false peak and enhances the true DoA peaks. Simulation shows that the proposed scheme reduces the root mean square error of the DoA estimation, compared with the conventional G-ESPRIT algorithm.

Network slicing for wide-area coordinated packet processing has attracted attentions for improving efficiency of handling network traffic. We have recently proposed a tag-based network slicing mechanism called OpenTag, and introduced the prototype implementation of the OpenTag redirector on an evaluation board. In this paper, we investigate the integration of the OpenTag redirector into a commercial network device. Our contributions are three-fold: (1) designing the architecture aiming OpenTag-capable intermediaries embedded on commercial network devices, (2) implementing a prototype of the embedded OpenTag redirector using the Advanced Mezzanine Card (AMC) which has an OCTEON network processor, (3) showing our implementation can tolerate high bandwidth environment.

Current distributions induced on a circular disk of conductor are analyzed rigorously for an electric dipole incidence, when the source dipole is polarized parallel to the disk and located at an arbitrary position, and they are evaluated numerically. As the height of the dipole increases, the current distribution of the dipole approaches that of the plane wave incidence. Using a multiple precision arithmetic, numerical data for the current distribution are obtained for larger radii of a disk than the former approach.

One key requirement for achieving network virtualization is resource isolation among slices (virtual networks), that is, to avoid interferences between slices of resources. This paper proposes two methods, per-slice shaping and per-link policing for network-resource isolation (NRI) in terms of bandwidth and delay. These methods use traffic shaping and traffic policing, which are widely-used traffic control methods for guaranteeing QoS. Per-slice shaping utilizes weighted fair queuing (WFQ) usually applied to a fine-grained flow such as a flow from a specific server application to a user. Since the WFQ for fine-grained flows requires many queues, it may not scale to a large number of slices with a large number of virtual nodes. Considering that the purpose of NRI is not thoroughly guaranteeing QoS but avoiding interferences between slices, we believe per-slice (not per virtual link) shaping satisfies our objective. In contrast, per-link policing uses traffic policing per virtual link. It requires less resource and achieves less-strict but more-scalable isolation between hundreds of slices (500 to 700 slices in estimation). Our results show that both methods perform NRI well but the performance of the former is better in terms of delay. Accordingly, per-slice shaping (with/without policing) is effective for delay-sensitive services while per-link policing may be sufficiently used for the other types of services.

A garbage collector relieves programmers from manual memory management and improves productivity and program reliability. However, there are many other finite system resources that programmers must manage by themselves, such as sockets and database connections. Growing resource leaks can lead to performance degradation and even program crashes. This paper presents the automatic resource collection approach called Resco (RESource COllector) to tolerate non-memory resource leaks. Resco prevents performance degradation and crashes due to resource leaks by two steps. First, it utilizes monitors to count resource consumption and request resource collections independently of memory usage when resource limits are about to be violated. Second, it responds to a resource collection request by safely releasing leaked resources. We implement Resco based on a Java Virtual Machine for Java programs. The performance evaluation against standard benchmarks shows that Resco has a very low overhead, around 1% or 3%. Experiments on resource leak bugs show that Resco successfully prevents most of these programs from crashing with little increase in execution time.

In order to reduce cost and improve efficiency, many data centers adopt virtualization solutions. The advent of virtualization allows multiple virtual machines hosted on a single physical server. However, this poses new challenges for resource management. Web workloads which are dominant in data centers are known to vary dynamically with time. In order to meet application's service level agreement (SLA), how to allocate resources for virtual machines has become an important challenge in virtualized server environments, especially when dealing with fluctuating workloads and complex server applications. User experience is an important manifestation of SLA and attracts more attention. In this paper, the SLA is defined by server-side response time. Traditional resource allocation based on resource utilization has some drawbacks. We argue that dynamic resource allocation directly based on real-time user experience is more reasonable and also has practical significance. To address the problem, we propose a system architecture that combines response time measurements and analysis of user experience for resource allocation. An optimization model is introduced to dynamically allocate the resources among virtual machines. When resources are insufficient, we provide service differentiation and firstly guarantee resource requirements of applications that have higher priorities. We evaluate our proposal using TPC-W and Webbench. The experimental results show that our system can judiciously allocate system resources. The system helps stabilize applications' user experience. It can reduce the mean deviation of user experience from desired targets.

Source coding with a helper is one of the most fundamental fixed-length source coding problem for correlated sources. For this source coding, Wyner and Ahlswede-Korner showed the achievable rate region which is the set of rate pairs of encoders such that the probability of error can be made arbitrarily small for sufficiently large block length. However, their expression of the achievable rate region consists of the sum of indefinitely many sets. Thus, their expression is not useful for computing the achievable rate region. This paper deals with correlated sources whose conditional distribution is related by a binary-input output-symmetric channel, and gives a parametric form of the achievable rate region in order to compute the region easily.

This paper is concerned with coding theorems in the optimistic sense for separate coding of two correlated general sources X1 and X2. We investigate the achievable rate region Ropt (X1,X2) such that the decoding error probability caused by two encoders and one decoder can be arbitrarily small infinitely often under a certain rate constraint. We give an inner and an outer bounds of Ropt (X1,X2), where the outer bound is described by using new information-theoretic quantities. We also give two simple sufficient conditions under which the inner bound coincides with the outer bound.