This paper proposes an SoC test architecture generation framework. It contains a database, which stores the test cost information of several DFTs for every core, and a DFT selection part which performs DFT selection for minimizing the test application time using this database in the early phase of the design flow. Moreover, the DFT selection problem is formulated and the algorithm that solves this problem is proposed. Experimental results show that bottlenecks in test application time when using a single DFT method for all cores in an SoC is reduced by performing DFT selection from two types of DFTs. As a result, the whole test application time is drastically shortened.

This paper proposes a test generation method using several partly compacted test plan tables for RTL data paths. Combinational modules in data paths are tested using several partly compacted test plan tables. Each partly compacted test plan table is generated from each grouped test plan set and is used to test combinational modules corresponding to the grouped test plans. The values of control signals in a partly compacted test plan table are supplied by a test controller. This paper also proposes the architecture of a test controller which can be synthesized in a reasonable amount of time, and proposes a test plan grouping method to shorten test length for data paths under a test controller area constraint. Experimental results for benchmarks show that the test lengths are shortened by 4 to 36% with -9 to 8% additional test controller area compared with the test generation method using test plans.

Since scan testing is not based on the function of the circuit, but rather the structure, it is considered to be both a form of over testing and under testing. Moreover, it is important to test VLSIs using the given function. Since the functional specifications are described explicitly in the FSMs, high test quality is expected by performing logical fault testing and timing fault testing. This paper proposes a fault-dependent test generation method to detect specified fault models completely and to increase defect coverage as much as possible under the test length constraint. We present experimental results for MCNC'91 benchmark circuits to evaluate bridging fault coverage, transition fault coverage, and statistical delay quality level and to show the effectiveness of the proposed test generation method compared with a stuck-at fault-dependent test generation method.

In recent years, to meet strict time-to-market constraints, it has become difficult for only one semiconductor design company to design a VLSI. Thus, design companies purchase IP cores from third-party IP vendors and design only the necessary parts. On the other hand, since IP cores have the disadvantage that copyright infringement can be easily performed, logic locking has to be applied to them. Functional logic locking methods using TTLock are resilient to SAT attacks however vulnerable to FALL attacks. Additionally, it is difficult to design logic locking based on TTLock at the gate level. This paper proposes a logic locking method, CRLock, based on SAT attack and FALL attack resistance at the register transfer level. The CRLock is a logic locking method for controllers at RTL in which the designer selects a protected input pattern and modifies the controller based on the protection input pattern. In experimental results, we applied CRLock to MCNC'91 benchmark circuits and showed that all circuits are resistant to SAT and FALL attacks.

Linear feed-forward/feedback shift registers are used as an effective tool of testing circuits in various fields including built-in self-test and secure scan design. In this paper, we consider the issue of testing linear feed-forward/feedback shift registers themselves. To test linear feed-forward/feedback shift registers, it is necessary to generate a test sequence for each register. We first present an experimental result such that a commercial ATPG (automatic test pattern generator) cannot always generate a test sequence with high fault coverage even for 64-stage linear feed-forward/feedback shift registers. We then show that there exists a universal test sequence with 100% of fault coverage for the class of linear feed-forward/feedback shift registers so that no test generation is required, i.e., the cost of test generation is zero. We prove the existence theorem of universal test sequences for the class of linear feed-forward/feedback shift registers.

As LSIs are two-dimensional structures, the number of external pins increases at a lower rate than the corresponding increase in the number of gates on the LSI. Therefore, the number of flip-flops on a scan path increases as the density of gates on LSIs rises, resulting in longer test application times. In this paper, three novel DFT strategies aimed at reducing test application time are proposed. DFT strategy 1 is a full scan design method with test point insertion, DFT strategy 2 is a partial scan design method, and DFT strategy 3 is a partial scan design method with test point insertion. Experimental results show that these DFT strategies reduced the test application times by 45% to 82% compared with conventional full scan design methods.

We will present a partial scan design method based on n-fold line-up structures in order to achieve high fault efficiency and reduce test pattern generation time for practical LSIs. We will also present a partial scan design method based on the state justification of pure load/hold FFs in order to achieve high fault efficiency and reduce the number of scan FFs for practical LSIs with lots of load/hold FFs. Experimental results for practical LSIs show that our presented methods can achieve high fault efficiency (more than 99%) and reduce the number of scan FFs for the LSI with lots of load/hold FFs.

In at-speed scan testing, capture power is a serious problem because the high power dissipation that can occur when the response for a test vector is captured by flip-flops results in excessive voltage drops, known as IR-drops, which may cause significant capture-induced yield loss. In low capture power test generation, the test vectors that violate capture power constraints in an initial test set are defined as capture-unsafe test vectors, while faults that are detected solely by capture-unsafe test vectors are defined as unsafe faults. It is necessary to regenerate the test vectors used to detect unsafe faults in order to prevent unnecessary yield losses. In this paper, we propose a new low capture power test generation method based on fault simulation that uses capture-safe test vectors in an initial test set. Experimental results show that the use of this method reduces the number of unsafe faults by 94% while requiring just 18% more additional test vectors on average, and while requiring less test generation time compared with the conventional low capture power test generation method.

In recent years, the growing density and complexity of VLSIs have led to an increase in the numbers of test patterns and fault models. Test patterns used in VLSI testing are required to provide high quality and low cost. Don't care (X) identification techniques and X-filling techniques are methods to satisfy these requirements. However, conventional X-identification techniques are less effective for application-specific fields such as test compaction because the X-bits concentrate on particular primary inputs and pseudo primary inputs. In this paper, we propose a don't care identification method for test compaction. The experimental results for ITC'99 and ISCAS'89 benchmark circuits show that a given test set can be efficiently compacted by the proposed method.

This paper proposes a test generation method using a compacted test table and a test generation method using a compacted test plan table for RTL data path circuits with DFT where hierarchical test generations are applicable. Moreover, a heuristic algorithm for a compacted test plan table generation is proposed. The proposed methods could shorten test lengths for some RTL data path circuits compared with the conventional hierarchical test generation method.

High power dissipation can occur by high launch-induced switching activity when the response to a test pattern is captured by flip-flops (FFs) in at-speed scan testing, resulting in excessive IR drop. IR drop may cause significant capture-induced yield loss in the deep submicron era. It is known that test modification methods using X-identification and X-filling are effective to reduce power dissipation in the capture cycle. Conventional low power dissipation oriented X-filling methods consecutively select FFs and assign values to decrease the number of transitions on the FFs. In this paper, we propose a novel low power dissipation oriented X-filling method using SAT Solvers that conducts simultaneous X-filling for some FFs. We also proposed a selection order of FFs based on a correlation coefficient between transitions of FFs and power dissipation. Experimental results show that the proposed method was effective for ISCAS'89 and ITC'99 benchmark circuits compared with justification-probability-based fill.