This paper reduces system imbalance by replacing the single-switch converter with a synchronized double-switch converter based on two active switches technique and hybrid balance technique, including active balance and passive balance for common mode noise reduction. The system balance is experimentally evaluated by the common mode rejection ratio (CMRR). Finally, examples show that the CMRR of the single-switch converter is improved from 1.67 dB to 32.04 dB when the double-converter with two active switches technique is applied and to 41.5 dB when the double-switch converter with hybrid balance technique is applied.

The minimum mean square error (MMSE) multiple antenna transmission scheme for a code division multiple access (CDMA) system was recently developed by Choi and Perreau [1]. In this paper, we first show that the zero-forcing (ZF) transmit beamformer for multiple antenna CDMA system has the same form as the MMSE beamformer given by Choi and Perreau. We then develop an analytical method to obtain a closed-form expression of the bit error rate (BER) of the ZF transmit beamformer when there are channel estimation errors. The analytical and simulation results show good agreement, and confirm the importance of accurate channel state information (CSI) at the transmitter when using the ZF transmit beamformer.

To achieve scalability and security, large networks are often structured hierarchically as a collection of domains. In hierarchical networks, the topology and QoS parameters of a domain have to be first aggregated before being propagated to other domains. However, topology aggregation may distort useful information. Although spanning tree aggregation can perfectly encode attribute information of symmetric networks, it can not be applied to asymmetric networks directly. In this paper, we propose a spanning tree based attribute aggregation method for asymmetric networks. The time complexity of the proposed method and the space complexity of its resulted aggregated topology are the same with that of the spanning tree aggregation method in symmetric networks. This method can guarantee that the attributes of more than half of the links in the networks are unaltered after aggregation. Simulation results show that the proposed method achieves the best tradeoff between information accuracy and space complexity among the existing asymmetric attribute aggregation methods.

The objective of this paper is to survey the Generalized Multi-Protocol Label Switching (GMPLS) based recovery technology for optical transport networks. This paper introduces standardization activities of the GMPLS based recovery technology in the Internet Engineering Task Force (IETF), and recent progress of related experiments. In addition, this paper extracts requirements for the GMPLS based recovery technology through the evaluation of existing network elements, which can be client nodes of the optical transport networks. The results of field evaluations on the GMPLS based recovery technology are also introduced in this paper. Then, this paper addresses the issues for future deployment of the GMPLS based recovery technology for the optical transport networks.

This paper describes a new method to detect speech segments online with identifying gender attributes for efficient dual gender-dependent speech recognition and broadcast news captioning. The proposed online speech detection performs dual-gender phoneme recognition and detects a start-point and an end-point based on the ratio between the cumulative phoneme likelihood and the cumulative non-speech likelihood with a very small delay from the audio input. Obtaining the speech segments, the phoneme recognizer also identifies gender attributes with high discrimination in order to guide the subsequent dual-gender continuous speech recognizer efficiently. As soon as the start-point is detected, the continuous speech recognizer with paralleled gender-dependent acoustic models starts a search and allows search transitions between male and female in a speech segment based on the gender attributes. Speech recognition experiments on conversational commentaries and field reporting from Japanese broadcast news showed that the proposed speech detection method was effective in reducing the false rejection rate from 4.6% to 0.53% and also recognition errors in comparison with a conventional method using adaptive energy thresholds. It was also effective in identifying the gender attributes, whose correct rate was 99.7% of words. With the new speech detection and the gender identification, the proposed dual-gender speech recognition significantly reduced the word error rate by 11.2% relative to a conventional gender-independent system, while keeping the computational cost feasible for real-time operation.

With the rapid adoption of mobile devices and location based services (LBS), applications provide with nearby information like recommending sightseeing resort are becoming more and more popular. In the mean time, traffic congestion in cities led to the development of mobile public transportation systems. In such applications, mobile devices need to communicate with servers via wireless communications and servers should process queries from tons of devices. However, because users can not neglect the payment for the wireless communications and server capacities are limited, decreasing the communications made between central servers and devices and reducing the burden on servers are quite demanding. Therefore, in this paper, we propose a cost-effective intelligent public transportation system, ACE-INPUTS, which utilizes a mobile device to retrieve the bus routes to reach a destination from the current location at the lowest wireless communication cost. To accomplish this task, ACE-INPUTS maintains a small amount of information on bus stops and bus routes in a mobile device and runs a heuristic routing algorithm based on such information. Only when a user asks more accurate route information or calls for a "leave later query", ACE-INPUTS entrusts the task to a server into which real-time traffic and bus location information is being collected. By separating the roles into mobile devices and servers, ACE-INPUTS is able to provide bus routes at the lowest wireless communication cost and reduces burden on servers. Experimental results have revealed that ACE-INPUTS is effective and scalable in most experimental settings.

This paper investigates the use of the affine transformation matrix when employing principal component analysis (PCA) to compress the data of 3D animation models. Satisfactory results were achieved for the common 3D models by using PCA because it can simplify several related variables to a few independent main factors, in addition to making the animation identical to the original by using linear combinations. The selection of the principal component factor (also known as the base) is still a subject for further research. Selecting a large number of bases could improve the precision of the animation and reduce distortion for a large data volume. Hence, a formula is required for base selection. This study develops an automatic PCA selection method, which includes the selection of suitable bases and a PCA separately on the three axes to select the number of suitable bases for each axis. PCA is more suitable for animation models for apparent stationary movement. If the original animation model is integrated with transformation movements such as translation, rotation, and scaling (RTS), the resulting animation model will have a greater distortion in the case of the same base vector with regard to apparent stationary movement. This paper is the first to extract the model movement characteristics using the affine transformation matrix and then to compress 3D animation using PCA. The affine transformation matrix can record the changes in the geometric transformation by using 44 matrices. The transformed model can eliminate the influences of geometric transformations with the animation model normalized to a limited space. Subsequently, by using PCA, the most suitable base vector (variance) can be selected more precisely.

The dependence of arcing duration and energy in break operations for automotive relays was analysed with breaking current/voltage waveforms. Endurance tests were conducted with AgSnO2, AgNi10 and AgNi0.15 contacts under the loads of resistance, lamp and inductance, respectively, at 14 VDC. The experimental results shows breaking current (or break arc) duration is usually low and stable before welding occurs. The welding may appear suddenly or randomly without any preceding cumulated increases in the arc duration, the quantity of electric charges, nor the arcing energy. The welded contacts may be re-opened in the later break operation and, thereafter, can keep on working normally for many times.

Excitation of plasmons on the surface of a metal grating placed in planar or conical mounting is investigated in detail. Most of the results of numerical computations are compared with experimental data. When a TM wave illuminates a metal grating, total or partial absorption of incident light occurs at angles of incidence at which the plasmon surface waves are excited. In planar mounting the absorption is generally strong and nearly total absorption is observed. While in conical mounting, it is not so strong as that in the planar mounting case and a considerable amount of incident power is reflected. This, however, is accompanied by enhanced TM-TE mode conversion and the greater part of the reflected wave is in the TE polarization. The reciprocal of the TM-wave efficiency, hence, is a practical measure in finding the angles of incidence at which the plasmons are excited. Because the angles are sensitive functions of the refractive index of a material over the grating surface, this phenomenon can be used as an index sensor.

Motion estimation (ME) is a computation intensive procedure in H.264. In ME for variable block sizes, an effective scan ordering method has been devised for early termination of absolute difference computation when the termination does not affect the performance. The new ME circuit with effective scan ordering can reduce the amount of computation by 70% compared to JM8.2 and by 30% compared to the disable approximation unit (DAU) approach.

Ag and Pd electrical contact pairs are separated at constant separating speeds (5, 10 and 20 mm/s) in a DC 42 V/8.4 A resistive circuit. The motion of the breaking arc is observed with a high-speed video camera. For Ag contacts, the motion of the breaking arc becomes stable at a certain critical gap at separating speeds of 10 mm/s and 20 mm/s, and the breaking arc moves extensively at the separating speed of 5 mm/s. For Pd contacts, the breaking arc moves extensively regardless of the separating speed. These results are attributed to the following causes. For Ag contacts, the difference in the motion of arc spots at each separating speed is changed by the difference in the total energy input to the contacts. For Pd contacts, the temperature of the contact surfaces is kept high because of the lower thermal conductivity of Pd than Ag.

The large PAPR of orthogonal frequency division multiplexing (OFDM) transmission is one of the serious problems for mobile communications that require severe power saving. Iterative clipping and filtering is an effective method for the PAPR reduction of OFDM signals. This paper evaluates PAPR reduction effect with a graded band-limiting filter in the iterative clipping and filtering method. The evaluation result by computer simulation shows that the excellent peak reduction effect can be obtained in the fewer iteration numbers by using a roll-off filter instead of the conventional rectangular filter, and the iteration number with the roll-off filter achieving the same PAPR is fewer by twice. The result confirms that the clipping and filtering method by using a graded band-limiting filter can achieve low peak OFDM transmission with less computational complexity.

This paper deals with the random number generation problem under the framework of a separate coding system for correlated memoryless sources posed and investigated by Slepian and Wolf. Two correlated data sequences with length n are separately encoded to nR1, nR2 bit messages at each location and those are sent to the information processing center where the encoder wish to generate an approximation of the sequence of independent uniformly distributed random variables with length nR3 from two received random messages. The admissible rate region is defined by the set of all the triples (R1,R2,R3) for which the approximation error goes to zero as n tends to infinity. In this paper we examine the asymptotic behavior of the approximation error inside and outside the admissible rate region. We derive an explicit lower bound of the optimal exponent for the approximation error to vanish and show that it can be attained by the universal codes. Furthermore, we derive an explicit lower bound of the optimal exponent for the approximation error to tend to 2 as n goes to infinity outside the admissible rate region.

We developed a comprehensive simulation system for evaluating satellite-based navigation services in highly built-up areas; the system can accommodate Global Positioning System (GPS) multipath effects, as well as line-of-sight (LOS) and dilution of position (DOP) issues. For a more realistic simulation covering multipath and diffracted signal propagations, a 3D-ray tracing method was combined with a satellite orbit model and three-dimensional (3D) geographic information system (GIS) model. An accuracy estimation model based on a 3D position determination algorithm with a theoretical delay-locked loop (DLL) correlation computation could measure the extent to which multipath mitigation improved positioning accuracy in highly built-up areas. This system could even capture the multipath effect from an invisible satellite, one of the greatest factors in accuracy deterioration in highly built-up areas. Further, the simulation results of satellite visibility, DOP, and multipath occurrence were mapped to show the spatial distribution of GPS availability. By using object-oriented programming, our simulation system can be extended to other global navigation satellite systems (GNSSs) simply by adding the orbital information of the corresponding GNSS satellites. We demonstrated the applicability of our simulation system in an experimental simulation for Shinjuku, an area of Tokyo filled with skyscrapers.

An adaptive subcarrier allocation (SA) algorithm is proposed for both the enhancement of system capacity and the practical implementation in a clustered OFDM system. The proposed algorithm is based on the two dimensional comparison of the channel gain in both rows and columns of the channel matrix to achieve higher system capacity. Simulation results demonstrate that the proposed algorithm outperforms the SA algorithm based on only one dimensional comparison in terms of system capacity, and furthermore, it performs as well as the optimal SA algorithm at relatively low computational cost.

Estimating the generalization error is one of the key ingredients of supervised learning since a good generalization error estimator can be used for model selection. An unbiased generalization error estimator called the subspace information criterion (SIC) is shown to be useful for model selection, but its range of application is limited to linear learning methods. In this paper, we extend SIC to be applicable to non-linear learning.

A hierarchical representation formed by an octree for a volume ray casting is a well-known data structure to skip over transparent regions requiring little preprocessing and storage. However, it accompanies unnecessary comparison and level shift between octants. We propose a new data structure named half-skewed octree, which is an auxiliary octree to support the conventional octree. In preprocessing step, a half-skewed octree selects eight different child octants in each generation step compared with the conventional octree. During rendering, after comparing an octant of the conventional octree with corresponding octant of the half-skewed octree simultaneously at the same level, a ray chooses one of two octants to jump over transparent regions farther away. By this method, we can reduce unnecessary comparison and level shift between octants. Another problem of a conventional octree structure is that it is difficult to determine a distance from the boundary of a transparent octant to opposite boundary. Although we exploit the previously proposed distance template, we cannot expect the acceleration when a ray direction is almost parallel to the octant's boundary. However, our method can solve it without additional operations because a ray selects one octant to leap farther away. As a result, our approach is much faster than the method using conventional octree while preserving image quality and requiring minimal storage.

A method for flexibly allocating and reallocating optical access network (OAN) resources, including fibers and equipment, using the constraint satisfaction problem (CSP) is described. OAN resource allocation during service delivery provisioning involves various input conditions and allocation sequences, so an OAN resource allocation method has to support various workflow patterns. Furthermore, exception processing, such as reallocating OAN resources once they are allocated, is inevitable, especially during the spread of service using optical fiber and during the deployment of an optical access network. However, it is almost impossible to describe all workflow patterns including exception processes. Improving the efficiency of these exception processes, as well as that of the typical processes, is important for reducing the service delivery time. Describing all these patterns and process flows increases development cost. The CSP can be used to search for solutions without having to fix the process sequence and input conditions beforehand. We have formulated the conditions for OAN resource allocation and reallocation as a CSP. Use of this method makes it possible to handle various allocation workflow patterns including exception processes. Evaluation of the solution search time demonstrated its feasibility.

Orthogonal frequency division multiplexing (OFDM) is one of the promising transmission techniques for next generation mobile communication systems. Accurate channel estimation is essential for coherent OFDM signal transmission. So far, many pilot-assisted channel estimation schemes have been proposed. In the case of packet transmission, each received packet can be repeatedly processed by decision feedback to improve the channel estimation accuracy, resulting in a decision directed block iterative channel estimation (DD-BICE). However, decision feedback of erroneously detected data symbols degrades the packet error rate (PER) or bit error rate (BER) performance. In this paper, theoretical analysis is presented for the DD-BICE taking into account the decision feedback errors assuming quadrature phase shift keying (QPSK) data modulation. A 2-dimensional (2D) averaging filter is used for reducing the negative impact of decision feedback errors. The impacts of 2D averaging filter and antenna diversity reception are discussed and the validity of the theoretical analysis is confirmed by computer simulation.

The traffic with asymmetry between uplink and downlink has recently been getting remarkable on mobile communication systems providing multimedia communication services. In the future mobile communications, the accommodation of asymmetric traffic is essential to realize efficient multimedia mobile communication systems. This paper discusses asymmetric traffic accommodation in CDMA/FDD cellular packet communication systems and proposes its efficient scheme using an adaptive cell sizing technique. In the proposed scheme, each base station autonomously controls its coverage area so that almost the same communication quality can be achieved across the service area under the asymmetric traffic conditions. We present some numerical examples to demonstrate the effectiveness of the proposed scheme by using computer simulation. The simulation results show that, under asymmetric traffic conditions, the proposed scheme can provide fair communication quality across the service area in both links and can improve total transmission capacity in the uplink.