A conflict detection support method for combining additional telecommunication services with existing services is proposed. In this method, telecommunication services are described by the STR (State Transition Rule) method which specifies a set of state transition rules. Though conflict detection in the past depended on manual analysis by the designer, with this method, conflict candidates are mechanically narrowed down and indicated to the designer. All conflicts between five actual telecommunication service descriptions are detected in an experiment using a system developed in line with the proposed method.

This paper presents a protocol verification method which verifies that the behaviors of a protocol meet requirements. In this method, a protocol specification is expressed as Extended Finite State Machines (EFSM's) that can handle variables, and requirements are expressed using a branching-time temporal logic for a concise and unambiguous description. Using the acyclic expansion algorithm extended such that it can deal with EFSM's, the verification method first generates a state transition graph consisting of executable transitions for each process. Then a branching-time temporal logic formula representing a requirement is evaluated on one of the generated graphs which is relevant to the requirement. An executable state transition graph for each process is much smaller than a global state transition graph which has been used in the conventional verification techniques to represent the behaviors of the whole protocol system consisting of all processes. The computation for generating the graphs is also reduced to much extent for a large complex protocol. As a result, the presented method achieves efficient verification for requirements regarding a state of a process, transmission and reception of messages by a process, varibales of a process and sequences that interact among processes. The validity of the method is illustrated in the paper by the verification of a path-updating protocol for requirements such as process state reachability or fair termination among processes.

This paper describes MENDELS ZONE, a Petri-net-based concurrent programming environment, which is especially suitable for cooperating discrete event systems. MENDELS ZONE adopts MENDEL net, which is a type of high level (hierarchical colored) Petri net. One of the characteristics of the MENDEL nets is a process-oriented hierarchy like CCS, which is different from the subnet-oriented hierarchy in the Jensen's hierarchical colored Petri net. In a process-oriented hierarchy, a hierarchical unit is a process, which is more natural for cooperating and decentralized discrete event control systems. This paper also proposes a design methodology for MENDEL nets. Although many Petri net tools have been proposed, most tools support only drawing, simulation, and analysis of Petri nets; few tools support the design methodology for Petri nets. While Petri nets are good final design documents easy to understand, analyzable, and executable it is often difficult to write Petri nets directly in an earlier design phase when the system structure is obscure. A proposed design methodology makes a designer to construct MENDEL nets systematically using causality matrices and temporal logic. Furthemore, constructed MENDEL nets can be automatically compiled into a concurrent programming language and executed on a parallel computer.

A job shop system typically seen in flexible manufacturing systems (FMS) is a system composed of a set of machines and a various kind of jobs processed with the machines. A production system of semiconductor fabrication is an example of job shop systems, which has main features of repetitive processes of one part and set-up times required for machines processing different types of parts. On the other hand, timed Petri nets are used for modelling and analyzing a wide variety of discrete event systems. There are many applications of timed Petri nets to the scheduling problems of job shop systems. The performance evaluation and steady state behaviors are studied by using the maximum cycle time of timed marked graphs. The aim of this paper is to propose a new model for production systems including repetitive processes and set-up time requirements which enables the quantitative analysis of real time system performance. In job shop systems such as a semiconductor fabrication system, it takes considerable amount of set-up time to prepare different types of chemical reactions and the model should take account of a set-up time for each machine. We focus upon the relationship between facility utilization factor and production cycle time in the steady state. In the proposed model, the minimum total set-up time can be attained. Quantitative relationship between utilization factor and production cycle time is derived by using the proposed model. A utilization factor of a system satisfying a given limit of the cycle time is evaluated, and the improvement of the utilization factor is considered. Conversely, we consider the improvement of the cycle time of a system satisfying a given limit of utilization factor.

In most of the methods proposed so far to design approximately linear phase IIR digital filters (IIR DFs), the design takes place only in the time or in the frequency domain. However, when both magnitude and phase responses are considered, IIR DFs with better frequency responses can be obtained if their characteristics in both domains are taken into account. This paper proposes a design method for approximately linear phase IIR DFs, which is based on parameter estimation techniques in the time domain followed by a nonlinear optimization algorithm in the frequency domain. Several examples are presented, illustrating the proposed method.

Behavioral extraction from circuit description is a useful technique for logic design verification. We have proposed a technique of extraction from combinational circuits and developed a prototype system. To use this system practically, it is necessary to deal with sequential circuits. In this paper, we will present a new technique to extract behavioral descriptions from synchronous sequential circuits which include some flip-flops. Flip-flops are classified to two types. The one is a part of control registers. The other is a part of data registers. Behavior of the circuit with control registers is described by the state transition. Behavior of the circuit with data registers is described by the movement of data among registers. There are many circuits, as micro processors, which realize a function after some times of state transitions occurred. In such circuits, it is more important to abstract the function than to extract each state transition. We have progressed our system to extract such behaviors.

Recently, Burch et al. proposed symbolic model checking method to verify sequential machines formally. The method, which is based on logic function manipulation using binary decision diagram, can handle large sequential machines that cannot be handled by the conventional techniques. The expressive power of Computational Tree Logic (CTL), which was used by Burch et al., is not very powerful, for example, CTL cannot describe repetition of events. This papers shows an extension of the symbolic model checking algorithm to Branching time regular temporal logic (BRTL), which has been proposed by the authors as an improvement of CTL in terms of expressive power. The implemented verifier based on the proposed algorithm could verify behaviors of a microprocessor composed of approximately 1,600 gates and 68 flipflops.

Recent trends in down-sizing have resulted in the development of client server systems for many industries. This paper considers the application of stochastic Petri nets with general firing times for modeling of a concatenated client server system and the use of discrete-event simulation methods for stochastic Petri nets to study its behavior. This approach enables us to assess the most appropriate resource set of a concatenated client server system on the quantitative basis of the performability and the occurrence of system down conditions. Thus, system consultation, a new application of stochastic Petri nets, is presented.

The pursuit of higher availability has resulted in the development of fault tolerant systems for many industries. However, system characteristics that can be perceived by the customer have never been diagnosed quantitatively. This paper considers the application of stochastic Petri nets with general firing times to modeling of a fault tolerant system and the use of discrete-event simulation methods for stochastic Petri nets to study the behavior of the system. The stochastic Petri net model incorporates factors that compose the system as well as those that accompany it, including RAS characteristics of products, personnel arrangements, and system management. By modeling the behavioral aspect of each factor, it is possible to diagnose a fault tolerant system quantitatively on the basis of customer impact.

We developed a 32-bit pseudorandom number generator (RNG) operating at liquid nitrogen temperature based on HEMT ICs. It generates maximum-length-sequence codes whose primitive polynomial is X47+X42+1 with the period of 247-1 clock cycle. We designed and fabricated three kinds of cryogenic HEMT IC for this system: A 1306-gate controller IC, a 3319-gate pseudorandom number generator (RNG) IC, and a buffer IC containing a 4-kb RAM and 514 gates. We used 0.6-µm gate-length Se-doped GaAlAs/GaAs HEMTs. Interconnects were Al for the first layer and Au/Pt/Ti for the second layer with a SiON insulator between them. The HEMT ICs have direct-coupled FET logic (DCFL) gates internally and emitter-coupled logic (ECL) compatible input-putput buffers. The unloaded basic delay of the DCFL gate was 17 ps/gate with a power consumption of 1.4 mW/gate at liquid nitrogen temperature. We used an automatic cryogenic wafer probe we developed and an IC tester for function tests, and used a high-speed performance measuring system we also developed with a bandwidth of more than 20 GHz for high-speed performance tests. Power dissipations were 3.8 W for the controller IC, 4.5 W for the RNG IC, and 3.0 W for the buffer IC. The RNG IC, the largest of the three HEMT ICs, had a maximum operating clock rate of 1.6 GHz at liquid nitrogen temperature. We submerged a specially developed zirconium ceramic printed circuit board carrying the HEMT ICs in a closed-cycle cooling system. The HEMT ICs were flip-chip-packaged on the board with bumps containing indium as the principal component. We confirmed that the RNG system operates at liquid nitrogen temperature and measured a minimum system clock period of 1.49 ns.

This paper describes a VLSI processor architecture designed for a back-propagation accelerator. Three techniques are used to accelerate the simulation. The first is a multi-processor approach where a neural network simulation is suitable for parallel processing. By constructing a ring network using several processors, the simulation speed is multiplied by the number of the processors. The second technique is internal parallel processing. Each processor contains 4 multipliers and 4 ALUs that all work in parallel. The third technique is pipelining. The connections of eight functional units change according to the current stage of the back-propagation algorithm. Intermediate data is sent from one functional unit to another without being stored in extra registers and data is processed in a pipeline manner. The data is in 24-bit floating point format (18-bit mantissa and 6-bit oxponent). The chip has about 88,000 gates, including microcode ROM for processor control, the processor is designed using 0.8-µm CMOS gate arrays, and the estimated performance at 40 MHz is 20 million connection updates per second (MCUPS). For a ring network with 4 processors, performance can be enhanced up to 90 MCUPS.

This paper deals with the sub-problems of generating a mask pattern from the logical description of a large-scale CMOS circuit. The large-scale layout can be generated in divide-and-conquer style: divide a given circuit into a set of sub-circuits, generate the layout of each sub-circuit, and merge the resulting layouts to create the whole layout. This paper proposes a layout synthesis algorithm for a sub-circuit with physical constraints for the synthesis scheme above. The physical constraints considered here are the relative placement of logic cells (sets of logic gates) and the routing constraint based on the costs of wiring layers and vias. These constraints will be given by the global optimizer in a two-dimensional layout synthesis routine, and they should be kept at the subsequent one-dimensional layout synthesis for a sub-circuit. The latter is also given for enhancing the circuit performance by limiting the usage of wiring layers and vias for special net such as a clock net. The placement constraint is maintained using PQ-tree, a tree structure representing a set of restricted permutations of elements. One-dimensional layout synthesis determines the placement of transistors by the enhanced pairwise exchanging method under the PQ-tree representation. The routing constraints is considered in the newly developed line-search routing method using a cost-based searching. Experimental results for practical standard cells, including up to 200 transistors, prove that the algorithms can produce the layouts comparable to handcrafted cells. Also on a two-dimensional layout synthesis using the algorithms, the results for benchmark circuits of Physical Design Workshop 1989, i.e., MCNC benchmark circuits, are superior to the best results exhibited at Design Automation Conference 1990.

Net-Oriented Analysis and Design (NOAD) is defined as three items: (1) Various nets are utilized as an effective modeling method. (2) Inter-relationships among verious nets are determined. (3) Verification or analysis methods for nets are provided and they are implemented based on the mathematical theory, that is Net theory. Very few methods have been presented to satisfy these three items. For example, the Real-Time SA method covers item (1) only. The Object-Oriented Analysis and Design method (OOA/OOD) covers items (1) and (2). NOAD can be regarded as an extension to OOA/OOD. This paper discusses how effectively various nets have been used in actual software development support metnods and tools and evaluates such several methods and tools from the NOAD viewpoint.

This paper describes a programming system, K-NET for the development of control software for flexible manufacturing systems composed of robots, numerically-controlled machines, transfer machines and automatic storage/retrieval systems. K-NET is based on a high-level Petri net which makes it simple to express operational functions such as synchronization, interlock and concurrence in sequence control. Petri net in K-NET is colored one in which tokens have attributes, and timed one which can provide a notion of stochastic time. K-NET provides many kinds of boxes having specific functions, and gates specified the firing condition and the token flow control with IF-THEN rules. On the other hand, procedural language can be also used for information processing. K-NET can support all development stages including general design, detailed design, programming and testing. K-NET has an editor to input control specifications expressed with Petri net; a simulator to verify edited specifications; a generator to convert the net to C source programs for a computer or to ladder diagrams for a programmable controller; a reporter to print control specifications; and a monitor to display controller status in real-time. K-NET has been used in the development of control software for an automated guided vehicle system, and results show a 2/3rds cost-saving over development with conventional methods in which only procedural language is used.

This paper describes the performance evaluation of the Translation Look-aside Buffer (TLB) for highly integrated microprocessors, especially concerning the TLB in the SPARC Reference MMU specification. The analysis covers configurations, the number of entries, and replacement algorithms for the instruction TLB and the data TLB, which are assumed to be practically integrated on one die. We also present performance improvement using a Page Table Cache (PTC). We evaluate some types of TLB configurations with software simulation and excute the Systems Performance Evaluation Cooperative (SPEC) programs.

High frequency and low power 128/129 dual modulus prescaler ICs are developed for mobile communication applications, using 0.5 µm GaAs MESFET technology. Provided with an on-chip voltage regulator, a prescaler IC with an input amplifier operates in a wide frequency range from 200 MHz to 1,500 MHz at input power from -15 dBm to +17 dBm at the temperature of -30 to +120 with supply voltage of 2.7 V, 3.0 V and 5.0 V. At the same time, it demonstrated its low power characteristics consuming 3.68 mA with 3.0 V at +30 in operation, 0.16 mA while powered-off. Another prescaler IC without an input amplifier operates up to 1,650 MHz with Vdd=2.7 V, 3.0 V and 5.0 V at +30, dissipating 2.74 mA/3.0 V.

In this paper, the software structure for telecommunication user support are discussed, and it is proposed to apply knowledge processing technology to the software. Capabilities of telecommunications networks are becoming quite complicated, and the number of service items and parameters which have to be selected and memorized will become too large for telecommunications end users to make full use of the network capabilities. As such, more effort should be focused on assisting telecommunications end users to use the network and providing user friendly human interfaces of the network. However, this kind of software has additional type of requirements other than those for protocol handling software and call control software, and the realization of such support software has not yet been fully studied. To realize such support software, this paper stressed the realization of the user-system interface. Especially identified in this paper are meaning-based interpretation of user inputs to permit the handling of synonyms and multivocations, and a method to access the database in the support system without consideration of its data schema. To satisfy these objectives, this paper has proposed that the application data should be represented in both a character string and a meaning representation, and that the thesauruses should have the attribute-value relation. In line with these studies, an experimental system called CAPRIS (CAlling PRocedure Instruction System) was developed. It is used to assist the calling party in a telecommunications network to find an appropriate contact point depending on the purpose of the communication. Implementation of CAPRIS is completed and it was confirmed that all the functions described in this paper were actually realized. Some functional experiments were performed on CAPRIS, and the system was concluded to realize satisfactory user-friendliness.

The subject of the paper is the minimum initial marking problem for scheduling in timed Petri net PN: given a vector X of nonnegative integers, a P-invariant Y of PN and a nonnegative integer π, find an initial marking M minimizing the value YtrM among those initial marking M such that there is a scheduling σ having the total completion time τ(σ)π with respect M , X and PN (a sequence of transitions, with the first transition firable on M , such that every transition t can fire prescribed number X(t) of times). The paper shows NP-hardness of the problem and proposes two approximation algorithms with their experimental evaluation.

The paper proposes a combined delay model to manipulate the variance of the delay time of logic elements and a new timing verification method based on the theory of regular expressions. With the delay time of logic elements such as TTL SN7400, the minimum delay time (dm), the maximum delay time (dM), and the typical delay time are specified in the manual, and the delay time of an element is one in the interval between dm and dM. Here we assume a discrete time, and we manipulate the variance of the delay time as a set of output strings corresponding to each delay time. We call the model as the combined delay model. Since many output strings are generated with a single input string, the usual timing simulation method cannot be applied. We propose a timing verification method using a behavior extraction method of logic circuits with respect to a time string set: with respect to the specified input set, the method extracts the output string set of each element in the circuit. We devised (1) a mechanism to keep the correspondence between a primary input string and an output string with respect to the primary input string, (2) a mechanism to manipulate the nondeterminism included in the combined delay model, and (3) an event-driven like data compaction method in representing finite automata. We focused on the hazard detection problem and the verification of asynchronous circuits, and show the effectiveness of our method with medium sized circuit with 100 elements or so. The method includes the state explosion, but the data compaction method and the extraction for only the specified input set are useful to control the state explosion.

The effectiveness of traffic shaping for VBR traffic is analyzed. Evaluation results prove that traffic shaping can improve link efficiency for most forms of bursty VBR traffic and that link efficiency gains of more than 250% can be expected without the shaping delay imposing any significant QOS deterioration. Traffic shaping increases the link efficiency to about 80% for traffic with short burst repetition periods. The traffic shaping techniques and analytical results described herein can be employed in the traffic management of future B-ISDN/ATM networks.