Blocking artifacts are introduced in many block-based coding systems, and its reduction can significantly improve the subjective quality of compressed video. The H.264/AVC uses an in-loop deblocking filter to remove the blocking artifacts. The filter considers some coding conditions in its adaptive deblocking filtering such as coded block pattern (CBP), motion vector, macroblock type, etc. for inter-predicted blocks, however, it does not consider much for intra-coded blocks. In this paper, we utilize the human visual system (HVS) characteristic and the local characteristic of image blocks to modify the boundary strength (BS) of the intra-deblocking filter in order to gain improvement in the subjective quality and also to reduce the complexity in filtering intra coded slices. In addition, we propose a low-complexity deblocking method which utilizes the correlation between vertical and horizontal boundaries of a block in inter coded slices. Experimental results show that our proposed method achieves not only significant gain in the subjective quality but also some PSNR gain, and reduces the computational complexity of the deblocking filter by 36.23% on average.

We report a 40-Gb/s and highly accurate intensity limiter with a single Erbium-Doped Fiber Amplifier (EDFA) for low-power-consumption driving intensity limiting. The intensity limiter based on self-phase modulation with an appropriate pre-chirping procedure makes it possible, which provides a highly accurate limiting of less than 0.01 dB. We fed 40-Gb/s signals with 2.69 dB intensity fluctuation and 4.7 dB improvement on the receiver sensitivity was obtained for a bit error rate of 10-9 by using a numerical simulation.

This paper describes two promising millimeter-wave measurement techniques suitable for biological materials. One is reflection-geometry imaging using a low-coherence signal, and the other is millimeter-wave ellipsometry. Imaging porcine tissue during the desiccation process, we found the temporal variation of the reflection intensity to be well explained by an exponential decrease of the relative dielectric constant. Ellipsometry results showed that the complex relative dielectric constant also decreased exponentially with time during the desiccation process and that for bovine tissue the gradients for the real and imaginary parts of the constant were different. The implications of these results on the distribution of water in biological tissues are discussed.

There has recently been much research on content-based image retrieval (CBIR) that uses image features including color, shape, and texture. In CBIR, feature extraction is important because the retrieval result depends on the image feature. Query-by-sketch image retrieval is one of CBIR and query-by-sketch image retrieval is efficient because users simply have to draw a sketch to retrieve the desired images. In this type of retrieval, selecting the optimum feature extraction method is important because the retrieval result depends on the image feature. We have developed a query-by-sketch image retrieval method that uses an edge relation histogram (ERH) as a global and local feature intended for binary line images. This histogram is based on the patterns of distribution of other line pixels centered on each line pixel that have been obtained by global and local processing. ERH, which is a shift- and scale-invariant feature, focuses on the relation among the edge pixels. It is fairly simple to describe rotation- and symmetry-invariant features, and query-by-sketch image retrieval using ERH makes it possible to perform retrievals that are not affected by position, size, rotation, or mirroring. We applied the proposed method to 20,000 images in the Corel Photo Gallery. Experimental results showed that it was an effective means of retrieving images.

In OFDM-based cognitive radio systems, due to the out-of-band leakage from the secondary transmission, the interference to primary users must be considered in order to guarantee the quality of service of the primary transmission. For multiuser cognitive radio systems, there exist two crucial issues in resource allocation: fairness and efficiency, in order to balance the two issues, we proposed a new utility-based cross-layer resource allocation algorithm, which can not only control the interference to primary users caused by secondary users, but also balance the spectral efficiency and fairness among cognitive users. Further, the optimal NP-hard resource allocation problem in multiuser OFDM-based systems is reduced to the sub-optimal solution by dividing the original problem into the subcarrier allocation problem and the power allocation problem. It is shown that the proposed algorithm can obtain the best performance in terms of the average rate or the utility among existing algorithms, and at the same time, all the users obtain fair resource allocation.

With appropriate geometry configurations, bistatic Synthetic Aperture Radar (SAR) can break through the limitations of monostatic SAR for forward-looking imaging. Thanks to such a capability, bistatic forward-looking SAR (BFSAR) has extensive potential applications. This paper develops a frequency-domain imaging algorithm for translational invariant BFSAR. The algorithm uses the method of Lengendre polynomials expansion to compute the two dimensional point target reference spectrum, and this spectrum is used to perform the range cell migration correction (RCMC), secondary range compression and azimuth compression. In particular, the Doppler-centroid and bistatic-range dependent interpolation for residual RCMC is presented in detail. In addition, a method that combines the ambiguity and resolution theories to determine the forward-looking imaging swath is also presented in this paper.

High phase noise is a common problem in ring oscillators. Continuous conduction of the transistor in an analog tuning method degrades the phase noise of ring oscillators. In this paper, a digital control tuning which completely switches the transistors on and off, and a 1/f noise reduction technique are employed to reduce the phase noise. A 14-bit control signal is employed to obtain a small frequency step and a wide tuning range. Furthermore, multiphase ring oscillator with a sub-feedback loop topology is used to obtain a stable quadrature outputs with even number of stages and to increase the output frequency. The measured DCO has a frequency tuning range from 554 MHz to 2.405 GHz. The power dissipation is 112 mW from 1.8 V power supply. The phase noise at 4 MHz offset and 2.4 GHz center frequency is -134.82 dBc/Hz. The FoM is -169.9 dBc/Hz which is a 6.3 dB improvement over the previous oscillator design.

We propose a coherent optical and radio seamless network concept that allows broadband access without deployment of additional optical fibers within an optical fiber dead zone while enhancing network resilience to disasters. Recently developed radio-over-fiber (RoF) and digital coherent detection technologies can seamlessly convert between optical and radio signals. A millimeter-wave radio with a capacity greater than 10 Gb/s and high-speed digital signal processing is feasible for this purpose. We provide a preliminary demonstration of a high-speed, W-band (75–110 GHz) radio that is seamlessly connected to an optical RoF transmitter using a highly accurate optical modulation technique to stabilize the center frequencies of radio signals. Using a W-band digital receiver with a sensitivity of -37 dBm, we successfully transmitted an 18.6 Gb/s quadrature-phase-shift-keying signal through both air and an optical fiber.

In our privious paper, we proposed an algorithm that determines delay times of a timed Petri net from the structural information of a signaling pathway, but Petri net structures containing cycles and inhibitory arcs were not considered. This paper provides conditions for cycle-contained Petri nets to have reasonable delay times. Furthermore, handling of inhibitory arcs are discussed in terms of the reaction rate of inhibitory interaction in signaling pathway, especially the conversion process of Petri net with inhibitory arc to the one without inhibitory arc is given.

This paper describes mobile backhaul optical access network designs for future cellular systems, in particular, for those systems that exploit coordinated multipoints (CoMP) transmission/reception techniques. Wavelength-division-multiplexing passive optical networks (WDM-PON) are primarily considered and two proposals to enhance mobile backhaul capability of WDM-PONs for CoMP are presented. One is physical X2 links that support dedicated low latency and high capacity data exchange between base stations (BSs). The other is multicasting in WDM-PONs. It effectively reduces data/control transmission time from central node to multiple BSs joining CoMP. Evaluation results verify that the proposed X2 links and the multicasting enable more BSs to join CoMP by enhancing the mobile backhaul capability, which results in improved service quality for users.

We propose a method of the precise frequency tuning in millimeter wave (MMW) generation using a Mach-Zehnder-modulator-based flat comb generator (MZ-FCG). The MZ-FCG generates a flat comb signal where the comb spacing is exactly the same as the frequency of a radio-frequency signal driving the MZ-FCG. Two modes are extracted from the comb signal by using optical filters. One of them was modulated by a phase modulator, creating precisely frequency-controllable sidebands. In the experiment, typical phase modulation was used. By photomixing of the extracted two modes using a high-speed photodiode, MMW signals with precisely frequency-controllable sidebands are generated. By changing the modulation frequency, the frequency of MMW signals can be continuously tuned. In this scheme, there are two methods for the frequency tuning of MMW signals; one is a coarse adjustment which corresponds to the comb spacing, and the other is fine tuning by the phase-modulation. It was demonstrated that the intensity fluctuation of the upper sideband of the modulated MMW signal was less than 1 dB, and the frequency fluctuation was less than the measurement resolution (300 Hz).

A direction-of-arrival estimation (DoA) scheme that uses a uniform circular array (UCA) is proposed for near-field sources, where multiple pairs-of-subarrays exist with central symmetry. First, multiple generalized ESPRIT (G-ESPRIT) spectrums are obtained by applying the conventional G-ESPRIT algorithm to each of multiple pairs-of-subarrays. Second, a parallel spectrum is found by adding up the reciprocals of these G-ESPRIT spectrums and taking the reciprocal of the total. The locations of peaks in the parallel spectrum give the DoAs being estimated. When a DoA approaches the translation direction of two subarrays, the conventional G-ESPRIT spectrum is broken by a false peak. Since the translation directions of pairs-of-subarrays are different from each other, the false peak, due to the DoA approaching one of translation directions, does not exist simultaneously in all G-ESPRIT spectrums. The parallel concatenation of the spectrums suppresses the false peak and enhances the true DoA peaks. Simulation shows that the proposed scheme reduces the root mean square error of the DoA estimation, compared with the conventional G-ESPRIT algorithm.

The important issue of an adaptive scheduling scheme is to maximize throughput while providing fair services to all users, especially under strict quality of service requirements. To achieve this goal, we consider the problem of multiuser scheduling under a given fairness constraint. A novel Adaptive Fairness and Throughput Control (AFTC) approach is proposed to maximize the network throughput while attaining a given min-max fairness index. Simulation results reveal that comparing to straightforward methods, the proposed AFTC approach can achieve the desired fairness while maximizing the throughput with short convergence time, and is stable in dynamic scenarios. The trade-off between fairness and throughput can be accurately controlled by adjusting the scheduler's parameters.

Three-dimensional (3D) video service is expected to be introduced as a next-generation television service. Stereoscopic video is composed of two 2D video signals for the left and right views, and these 2D video signals are encoded. Video quality between the left and right views is not always consistent because, for example, each view is encoded at a different bit rate. As a result, the video quality difference between the left and right views degrades the quality of stereoscopic video. However, these characteristics have not been thoroughly studied or modeled. Therefore, it is necessary to better understand how the video quality difference affects stereoscopic video quality and to model the video quality characteristics. To do that, we conducted subjective quality assessments to derive subjective video quality characteristics. The characteristics showed that 3D video quality was affected by the difference in video quality between the left and right views, and that when the difference was small, 3D video quality correlated with the highest 2D video quality of the two views. We modeled these characteristics as a subjective quality metric using a training data set. Finally, we verified the performance of our proposed model by applying it to unknown data sets.

This paper presents a second-order ΔΣ analog-to-digital converter (ADC) operating in a time domain. In the proposed ADC architecture, a voltage-controlled delay unit (VCDU) converts an input analog voltage to a delay time. Then, the clocks outputs from a gated ring oscillator (GRO) are counted during the delay time. No switched capacitor or opamp is used. Therefore, the proposed ADC can be implemented in a small area and with low power. For that reason, it has process scalability: it can keep pace with Moore's law. A time error is propagated to the second GRO by a multi-stage noise-shaping (MASH) topology, which provides second-order noise-shaping. In a standard 40-nm CMOS process, a SNDR of 45 dB is achievable at input bandwidth of 16 kHz and a sampling rate of 8 MHz, where the power is 408.5 µW. Its area is 608 µm2.

The security of biometric authentication systems against impersonation attack is usually evaluated by the false accept rate, FAR. The false accept rate FAR is a metric for zero-effort impersonation attack assuming that the attacker attempts to impersonate a user by presenting his own biometric sample to the system. However, when the attacker has some information about algorithms in the biometric authentication system, he might be able to find a “strange” sample (called a wolf) which shows high similarity to many templates and attempt to impersonate a user by presenting a wolf. Une, Otsuka, Imai [22],[23] formulated such a stronger impersonation attack (called it wolf attack), defined a new security metric (called wolf attack probability, WAP), and showed that WAP is extremely higher than FAR in a fingerprint-minutiae matching algorithm proposed by Ratha et al. [19] and in a finger-vein-patterns matching algorithm proposed by Miura et al. [15]. Previously, we constructed secure matching algorithms based on a feature-dependent threshold approach [8] and showed that if the score distribution is perfectly estimated for each input feature data, then the proposed algorithms can lower WAP to a small value almost the same as FAR. In this paper, in addition to reintroducing the results of our previous work [8], we show that the proposed matching algorithm can keep the false reject rate (FRR) low enough without degrading security, if the score distribution is normal for each feature data.

This paper proposes a dynamic bandwidth allocation algorithm that improves the network performance and bandwidth sharing efficiency in the upstream channels of a hybrid passive optical network (PON) that combines a fiber-to-the-home (FTTH) access network and wireless sensor networks (WSNs). The algorithm is called the adaptive limited dynamic bandwidth allocation (ALDBA) algorithm. Unlike existing algorithms, the ALDBA algorithm is not limited to controlling just FTTH access networks, it also supports WSNs. For the proposed algorithm, we investigate the difference in the lengths of generated data packets between the FTTH terminals and sensor nodes of WSN to effectively evaluate the end-to-end average packet delay, bandwidth utilization, time jitter, and upstream efficiency. Two variants of the proposed algorithm and a limited service (LS) scheme, which is an existing well-known algorithm, are compared under non-uniform traffic conditions without taking into consideration priority scheduling. We demonstrate the proposed scheme through simulation by generating a realistic network traffic model, called self-similar network traffic. We conducted a detailed simulation using several performance parameters to validate the effectiveness of the proposed scheme. The results of the simulation showed that both ALDBA variants outperformed the existing LS scheme in terms of average packet delay, bandwidth utilization, jitter, and upstream efficiency for both low and high traffic loads.

As one innovative research that heavily depends on the network virtualization for its realization and deployment on an Internet-scale, we propose an approach to utilize user resources in information-centric network (ICN). We try to fully benefit from the in-network cache that is one attractive feature of ICN by expanding the in-network cache indirectly based on the user resources. To achieve this, in this paper, we focus on how to encourage users to contribute their resources in ICN. Through simulations, we examine a feasibility of our approach and an effect of user participation on the content distribution performance in ICN. We also briefly discuss how the network virtualization technique can be utilized for our research in terms of its evaluation and deployment.

In this paper, we derive a fast polynomial basis multiplier for GF(2m) defined by pentanomials xm+xk3+xk2+xk1+1 with 1 ≤ k1 < k2 < k3 ≤ m/2 using the presented method by Park and Chang. The proposed multiplier has the time delay TA+(2+⌈log2(m-1)⌉) TX or TA+(3+⌈log2(m-1)⌉) TX which is the lowest one compared with known multipliers for pentanomials except for special types, where TA and TX denote the delays of one AND gate and one XOR gate, respectively. On the other hand, its space complexity is very slightly greater than the best known results.

In OFDM systems, residual inter-block interference can be suppressed by a time-domain equalizer that blindly shortens the effective length of a channel impulse response. To further improve the performance of blind equalizers, we propose a channel shortening method that attempts to maximize the minimum FFT output power over data subcarriers. Simulation results indicate that the max-min strategy has performance improvement over a conventional channel shortening method.