Data-Over-Cable Service Interface Specifications v1.1 (DOCSIS v1.1), developed for data transmissions over Hybrid Fiber Coaxial (HFC) networks, defines five upstream services for supporting per-flow Quality of Services (QoS). The cable modem termination system (CMTS) must periodically grant upstream transmission opportunities to the QoS flows based on their QoS parameters. However, packets may violate QoS requirements when several flows demand the same interval for transmission. This study proposes a two-phase, i.e., the scheduling sequence determination phase and the minislot assignment phase, minislot scheduling algorithm to reduce the QoS violation rate. In the scheduling sequence determination phase, the flow whose packets are most unlikely to violate QoS is scheduled first. Then, in the minislot assignment phase, the scheduler allocates to a flow the available interval where the likelihood of packet violation is minimum. Simulation results demonstrate that our scheduling algorithm can reduce the QoS violation rate by 80-35% over that of the first-come-first-serve-random-selection algorithm. It increases the utilization by 25% as well. The two-phase minislot scheduling algorithm can work within the DOCSIS v1.1 framework.

It is shown that the effective secret-key size of TOYOCRYPT-HS1 stream cipher is only 96 bits, although the secret key consists of 128 bits. This characteristic opens a door for developing an algorithm for cryptanalysis based on the time-memory-data trade-off with the overall complexity significantly smaller than the exhaustive search over the effective key space.

In many cryptographic protocols, a common-key encryption is used to provide a secure data-transmission channel. More precisely, the general idea of protocols is to have an encryption provide data authenticity as well as data confidentiality. In fact, there are known to be quite a few ways to provide both forms of security, however none of them are optimized enough to be efficient. We present a new encryption mode that uses a random number generator (RNG). Assuming the security of the RNG, we can prove not only perfect secrecy, but also message authentication. The proven probability of a successful forgery is (n-1)/(2b-1), where b is the number of bits in a block and n is the number of ciphertext blocks. The proposed scheme achieves very high practicality due to the potential advantages in efficiency. When we use a computationally secure RNG, such as instance a pseudorandom number generator PRNG, we have advantages in efficiency; in addition to the PRNG parallel computation, the scheme requires only a single-path process on the data stream so that even a limited hardware resource can operate an encryption of a very long data stream. We demonstrate the practicality of our scheme, by showing a realistic parameter set and the evaluations of its performance.

The function of a message authentication code (MAC) is to verify the validity of a whole message. The disadvantage of usual MACs is that a receiver can not check its validity until the receipt of a message is finished. Hence, usual MACs are not suitable for verifying a large amount of data such as video and audio (called stream). In this letter, we propose a MAC such that the validity of a stream can be consecutively verified without waiting for the end of the reception. In addition, we show its implementations: one is based on practical hash functions, and the other is based on universal hash functions.

We will discuss a novel non-contact removal technique of optical fiber coating in continuous and uninterrupted manner with hot air stream. We observed little degradation of the tensile strength of the optical fiber after removing the protective polymer coating and the mean breaking tensile strength of the stripped optical fiber using non-contact removal method was 5.1 GPa.

This paper aims to provide a robust multiuser detection structure that adaptively tracks signature waveform distortion for CDMA multipath signals. In practical wireless environment, multipath fading leads to signature waveform distortion that severely degrades the performance of the linear multiuser detectors (LMDs) designed by exploiting the original signature waveform. In what follows, an iterative algorithm is proposed to track the signature waveform perturbation. The rationale of adaptive processing is based on the subspace method and the Minimum Variance Distortionless Response (MVDR) beamforming concept. Performance evaluation reveals that the proposed adaptive multiuser detection structure reduces the impact of signature waveform perturbation on the performance of the LMDs to a great extent. Moreover, the proposed iterative algorithm is near-far resistant since both the subspace method and the MVDR beamforming technique are energy independent to the interferers.

The design of an electron gun was examined from the viewpoints of pre-focus lens, main lens, corner focus and cathode current. Accordingly, multi-beam electron gun has been developed to catch up with the remarkable progress of resolution in computer peripheral devices such as digital still cameras and video boards. Multi-beam electron gun has two slot beam apertures of G1 for one cathode, and a key point of its design is to realize two-beam simultaneous convergence and focusing. To satisfy this condition, the divergence angles of electron beam bundles were designed. With this multi-beam electron gun that is superior in both of beam spot size and drive voltage, the 5 million pixels CRT could be realized.

This paper presents the performance of the Directionally Constrained Minimization of Power (DCMP) and the Zero-Forcing (ZF) in the Angular Spread (AS) environment. To obtain the optimal weights for both methods, the Extended Array Mode Vector (EAMV) is employed. It is known that the EAMV represents the instantaneous AS as well as the instantaneous DOA in the slow fading channel. As a result, it is shown that the DCMP and the ZF using the EAMV estimates can improve the Signal-to-Interference-plus-Noise Ratio (SINR) considerably, as compared with those using the Direction of Arrival (DOA) information only. At the same time, the intrinsic problems causing the performance loss in the DCMP and the ZF are revisited. From this, the reasons for the performance deterioration are analyzed, in relation with the AS, the number of samples, the number of antenna elements, and the spatial correlation coefficient of the signals. It follows that the optimal signal combining techniques using the EAMV estimates can diminish such effects.

The present paper describes the finite difference time domain (FDTD) analysis of the light-beam diffraction from two- and three-dimensional (2-D and 3-D) magneto-optical (MO) disk structures. First, we show that the proposed new FDTD formulation is valid for MO disk medium and can avoid the divergence of fields encountered during the conventional FDTD calculations. Second, as the application of the present method to more complicated models, the main- and cross-polarized diffracted fields are numerically calculated for 2-D and 3-D four-layered MO disk models. The phase differences between two kinds of polarized components are shown. The results obtained here indicate that the proposed FDTD formulation can be applied to more complicated MO disk structures.

An optically controlled beamforming technique is a very effect procedure for phased array antenna control. We have built a Fourier optical processing beamforming network. In the optical processor, we use optical waveguide arrays and a GRIN micro lens in order to reduce the size and weight of the processor, optical coupling losses, mechanical destabilization, and optical alignment difficulties. This paper describes the characteristics of a one-dimensional Fourier optical processor, and shows the configurations of both its transmitting and receiving modes, which we have constructed. We demonstrate multiple signal generation, and beam steering for transmission in the X-band. Furthermore, we configure the beamformer for reception using the phase information of local signals form the optical processor. We additionally demonstrate the beam steering of the received X-band RF signal. Experimental results confirm the feasibility of the Fourier optical processing beamforming network.

Several configurations of millimeter wave Gaussian Beam Antennas (GBAs) are studied in this paper. A GBA is a quasi-planar radiating structure comprising a plano-convex half-wavelength Fabry-Perot (FP) resonator excited by a guided source or by a printed source. Both partially transparent mirrors of the resonator are formed with two-dimensional metal meshes. GBAs have very low side lobes, because of the gaussian distribution of the aperture electric field. They can be efficiently used in Wireless Local Area Networks in the 60 GHz band. After a brief presentation of intrinsic properties of FP cavities illuminated by a plane wave under normal incidence, performances of four passive GBAs are described and compared to theoretical results: the first two configurations concern cavities fed either by a waveguide (GBA#1), or by a pyramidal horn antenna (GBA#2); in the last two ones, the cavities are excited by a linearly polarized microstrip patch antenna (GBA#3), or by a coaxial-probe circularly polarized antenna array (GBA#4). These various examples enable to deduce and to compare typical radiation performances of GBAs, depending on (i) the feeding technique (planar or guided), on (ii) the geometry of the FP resonator (radius of curvature, grid parameters) and on (iii) the polarization (linear or circular). In particular, for a planar primary source, it is shown that the directivity and the efficiency of GBAs are respectively in the range [15.5 dB-23.5 dB] and [20%-50%], if power reflectivities of both mirrors are higher than 96.5% and lower than 99.5%, and if the radius of curvature of the cavity varies between 30λ0 and 1600λ0.

In this paper, a novel beam selection transmit diversity (BSTD) scheme is proposed for the downlink transmission of frequency division duplex (FDD) based DS-CDMA system. As a combination of selection transmit diversity and steering vector based beamforming, the BSTD scheme provides diversity gain as well as reducing multiple access interference in downlink. Moreover, to have a better understanding, the performance of the BSTD is also compared with other schemes. The comparison results show that the BSTD would be a promising candidate for the downlink transmission if both performance and implementation complexity are considered.

This letter introduces an alternative adaptive beamforming with the total computational load of about O(3N) where N denotes the number of antenna elements. The proposed technique finds a weight vector that maximizes the received signal power at the array output by searching for the suboptimal phase of each weight in a multipath fading CDMA mobile communication environment.

Precise and quick multi-beam forming including null control will be one of the key technologies for the future satellite communication systems utilizing SDMA (Space Division Multiple Access) and DOA (Direction of Arrival) estimation. In order to realize the precise multi-beam forming, calibration procedure is indispensable since there are several unavoidable factors that degrade the multi-beam patterns of the array. Particularly amplitude and phase imbalance between RF circuits needs to be calibrated frequently and quickly when the array system exists in changeable environment since the imbalance easily occurs due to thermal characteristics of each RF circuit. This paper proposes a simple and high-speed remote calibration scheme compensating for amplitude and phase imbalance among RF circuits of a transmitting adaptive array antenna onboard satellite. This calibration is conducted at a remote station such as a gateway station on the ground in the satellite communication system, by utilizing the received signal including the temporally multiplexed orthogonal codes transmitted from the array antenna onboard satellite. Since the calibration factors for all the antenna elements can be simultaneously obtained by the parallel digital signal processing, calibration time can be drastically reduced. The accuracy of this calibration is estimated by simulation. Simulation results show that the amplitude imbalance among RF circuits can be suppressed within the range from -0.5 dB to +0.25 dB for the initial imbalance ranging from -2 dB to +3.5 dB, phase imbalance can be suppressed within the range of -3 deg. to +3 deg. for the initial imbalance ranging from -120 or +180 deg. by this method. The amplitude and phase deviations among the elements can be suppressed within 0.36 dB and 2.5 degrees, respectively, in 80% of probability. Simulation results also show that this calibration method is valid under the relatively bad carrier-to-noise conditions such as -10 dB at the receiver. Good improvement of the multi-beam patterns by this calibration is shown under the low carrier-to-noise ratio condition.

The worldwide availability of the Industrial Scientific and Medical (ISM) bands has prompted the proposal of several communication systems for indoor application at the 2.4 and 5 GHz bands. Although adaptive array antennas have been thoroughly investigated for various outdoor scenarios, their application to indoor communications has been overlooked. Experimental results indicating that conventional array antenna techniques exhibit poor performance when implemented indoors have recently been published. An important peculiarity of the indoor channel is the coexistence of both near-field and far-field propagating waves. Therefore, algorithms that can indifferently cope with both near-field and far-field wavefronts for source location and beamforming are desirable. In this paper, the following are presented. First, a mathematical analysis of the performance of array antennas in the indoor environment is taken up. Second, a new, simple, cost-effective and statistically coherent scheme, the Adaptive Sampling algorithm, is proposed for location estimation of sources anywhere from near field to far field. It is shown that the proposed algorithm achieves ubiquitous source location, allowing for symmetric uplink/downlink beamforming with seamless performance. Finally, the performance of the proposed Adaptively Sampled Array Antenna is performance analyzed via computer simulations under the specifications of the IEEE802.11b DS Wireless Local Area Network (W-LAN).

In this paper, we report on our recent work in designing and developing an optical waveguide and optical integrated circuit for optical BFN in adaptive multibeam array antenna. We introduce a new integrated Ti:LiNbO3 waveguide and prove that it is able to yield large birefringence and birefringence dispersion. We present a new technique using a microwave-modulated optical wave to measure the birefringence in integrated Ti:LiNbO3 optical waveguides. The measuring results show that the new waveguide has a birefringence of 0.08 and birefringence dispersion of 0.05 µm-1 at optical wavelength of 1.55 µm. When the new Ti:LiNbO3 is applied to form a integrated optical waveguide array in optical beamforming network, it is shown that microwave phase shifts within the range of [-180, +180] is achieved by tuning the optical wavelength 10 nm around 1.55 µm.

In wideband direct sequence code division multiple access (W-CDMA), employing an adaptive antenna array is a very promising technique to reduce severe multiple access interference (MAI) especially from high rate users. This paper proposes a fast and accurate two-step beam tracking algorithm implemented in a pilot symbol-assisted coherent adaptive antenna array diversity (CAAAD) receiver and evaluates its performance both by computer simulation and laboratory experiments. In the proposed scheme, the receiver antenna weights are updated by using both the signal-to-interference power ratio (SIR) measurements employing multiple sets of antenna weights (MSAW) and an adaptive algorithm based on the minimum mean square error (MMSE) criterion, in which other sets except for a original set of antenna weights are simply generated by a original set. Computer simulation results show that antenna weights of a four-antenna CAAAD receiver using the proposed beam tracking algorithm tracks changes in the direction of arrival (DOA) of the desired user at up to 34.3 degrees/sec, which corresponds to 215 km/h at 100 m from a base station. We also confirm based on the experiments in a radio anechoic room that the generated antenna weights track the DOA changes up to 12.3 degrees/sec.

This paper compares the path detection probability for Rake combining and the BER performance of packet transmission with the length of TPKT = 10 (20) msec using the coherent adaptive antenna array diversity (CAAAD) receiver with those using a multi-beam receiver employing fixed antenna weights both with four antennas in a multipath fading channel in the W-CDMA reverse link. Laboratory experimental results elucidate that the required average received signal energy per bit-to-background noise spectrum density (Eb/N0) at the detection probability of 90% of at least one path and of two paths for the fading maximum Doppler frequency of fD = 5 (80) Hz using a multi-beam receiver with the number of beams equal to NBeam = 12 was decreased by approximately 1.0 (1.0) dB and 2.0 (2.0) dB, respectively, compared to that using the CAAAD receiver with the step size of µ= 10-2 for the average received SIR of the desired user of -12 dB in a 2-path Rayleigh fading channel with average equal power in a 5-user environment. We also found that the required average received Eb/N0 at the average BER of 10-3 using the multi-beam receiver was decreased by approximately 5.0 (2.5) dB compared to that of the CAAAD receiver with µ= 10-2, and the loss of the required average received Eb/N0 compared to that of CAAAD with sufficiently converged receiver antenna weights was approximately 2.0 (1.0) dB for TPKT = 10 (20) msec when the average received SIR = -12 dB in a 5-user environment.

Conventional adaptive array antenna processing must access signals on all of the array antenna elements. However, because the low-cost electronically steerable passive array radiator (ESPAR) antenna only has a single-port output, all of the signals on the antenna elements cannot be observed. In this paper, a technique for adaptively controlling the loaded reactances on the passive radiators, thus forming both beam and nulls, is presented for the ESPAR antenna. The adaptive algorithm is based on the steepest gradient theory, where the reactances are sequentially perturbed to determine the gradient vector. Simulations show that the ESPAR antenna can be adaptive. The statistical performance of the output SIR of the ESPAR antenna is also given.

This paper focuses on a multi-beam combining scheme for DS-CDMA systems, which has RAKE combiners in multiple overlapped beams, in order to increase the reverse link capacity of DS-CDMA. This scheme is a very attractive technique because the maximal ratio combining (MRC) is carried out in space and time domains. However, in a practical situation, since the terminals in own sector are not uniformly located, the interference levels in respective beams are different. Therefore, receivers at the base station do not achieve ideal combining. This paper proposes a multi-beam combining scheme for DS-CDMA systems using weighting factor based on interference level of each beam. A fast closed loop transmission power control (TPC) scheme for the multi-beam combining system is also proposed. It is confirmed by computer simulation that the proposed scheme has excellent performance in the reverse link even if terminals in own sector are not uniformly located.