Yuma MURAKAWA Yuhei SADANDA Takashi HIKIHARA
This paper discusses the parallelization of boost and buck converters. Passivity-based control is applied to each converter to achieve the asymptotic stability of the system. The ripple characteristics, error characteristics, and time constants of the parallelized converters are discussed with considering the dependency on the feedback gains. The numerical results are confirmed to coincide with the results in the experiment for certain feedback gains. The stability of the system is also discussed in simulation and experiment. The results will be a step to achieve the design of parallel converters.
Koichi HIRAYAMA Jun-ichiro SUGISAKA Takashi YASUI
We propose the design method of a compact long-wavelength-pass filter implemented in a two-dimensional metal-dielectric-metal (MDM) waveguide with three stubs using a transmission line model based on a low-pass prototype filter, and present the wavelength characteristics for filters in an MDM waveguide based on 0.5- and 3.0-dB equal-ripple low-pass prototype filters.
This paper addresses the problem of developing an efficient fault-tolerant routing method for 2D mesh Network-on-Chips (NoCs) to realize dependable and high performance many core systems. Existing fault-tolerant routing methods have two critical problems of high communication latency and low node utilization. Unlike almost all existing methods where packets always detour faulty nodes, we propose a novel and unique approach that packets can pass through faulty nodes. For this approach, we enhance the common NoC architecture by adding switches and links around each node and propose a fault-tolerant routing method with no virtual channels based on the well-known simple XY routing method. Simulation results show that the proposed method reduces average communication latency by about 97.1% compared with the existing method, without sacrificing fault-free nodes.
Po-Yu KUO Chia-Hsin HSIEH Jin-Fa LIN Ming-Hwa SHEU Yi-Ting HUNG
A novel low power sense-amplifier based flip-flop (FF) is presented. By using a simplified SRAM based latch design and pass transistor logic (PTL) circuit scheme, the transistor-count of the FF design is greatly reduced as well as leakage power performance. The performance claims are verified through extensive post-layout simulations. Compared to the conventional sense-amplifier FF design, the proposed circuit achieves 19.6% leakage reduction. Moreover, the delay, and area are reduced by 21.8% and 31%, respectively. The performance edge becomes even better when the flip-flop is integrated in N-bit register file.
Lu LU Guangxia LI Tianwei LIU Siming LI Shiwei TIAN
Positioning information plays a significant role in multi-unmanned aerial vehicles (UAVs) applications. Traditionally, the positioning information is widely provided by Global Navigation Satellite System (GNSS) due to its good performance and global coverage. However, owing to complicated flight environment or signal blockage, jamming and unintentional interference, the UAVs may fail to locate themselves by using GNSS alone. As a new method to resolve these problems, cooperative positioning, by incorporating peer-to-peer range measurements and assisted information, has attracted more and more attentions due to its ability to enhance the accuracy and availability of positioning. However, achieving good performance of cooperative positioning of multi-UAVs is challenging as their mobility, arbitrary nonlinear state-evolution, measurement models and limited computation and communication resources. In this paper, we present a factor graph (FG) representation and message passing methodology to solve cooperative positioning problem among UAVs in 3-dimensional environment where GNSS cannot provide services. Moreover, to deal with the nonlinear state-evolution and measurement models while decreasing the computation complexity and communication cost, we develop a distributed algorithm for dynamic and hybrid UAVs by means of Spherical-Radial Cubature Rules (CR) method with belief propagation (BP) and variational message passing (VMP) methods (CRBP-VMP) on the FG. The proposed CRBP deals with the highly non-linear state-evolution models and non-Gaussian distributions, the VMP method is employed for ranging message, gets the simpler message representation and can reduce communication cost in the joint estimation problem. Simulation results demonstrate that the higher positioning accuracy, the better convergence as well as low computational complexity and communication cost of the proposed CRBP-VMP algorithm, which can be achieved compared with sum-product algorithm over a wireless network (SPAWN) and traditional Cubature Kalman Filters (CKF) method.
Zhijie CHEN Peiyuan WAN Ning LI
This paper discusses non-ideal issues in a fully passive noise shaping successive approximation register analog-to-digital converter. The fully passive noise shaping techniques are realized by switches and capacitors without operational amplifiers to be scalable and power efficient. However, some non-ideal issues, such as parasitic capacitance, comparator noise, thermal noise, will affect the performance of the noise shaping and then degrade the final achievable resolution. This paper analyzes the effects of the main non-ideal issues and provides the design reference for fully passive noise shaping techniques. The analysis is based on 2nd order fully passive noise shaping SAR ADC with an 8-bit architecture and an OSR of 4.
Jingjing SI Yinbo CHENG Kai LIU
Generalized approximate message passing (GAMP) is introduced into distributed compressed sensing (DCS) to reconstruct jointly sparse signals under the mixed support-set model. A GAMP algorithm with known support-set is presented and the matching pursuit generalized approximate message passing (MPGAMP) algorithm is modified. Then, a new joint recovery algorithm, referred to as the joint MPGAMP algorithm, is proposed. It sets up the jointly shared support-set of the signal ensemble with the support exploration ability of matching pursuit and recovers the signals' amplitudes on the support-set with the good reconstruction performance of GAMP. Numerical investigation shows that the joint MPGAMP algorithm provides performance improvements in DCS reconstruction compared to joint orthogonal matching pursuit, joint look ahead orthogonal matching pursuit and regular MPGAMP.
Yifei LIU Yuan ZHAO Jun ZHU Bin TANG
A novel Nyquist Folding Receiver (NYFR) based passive localization algorithm with Sparse Bayesian Learning (SBL) is proposed to estimate the position of a spaceborne Synthetic Aperture Radar (SAR).Taking the geometry and kinematics of a satellite into consideration, this paper presents a surveillance geometry model, which formulates the localization problem into a sparse vector recovery problem. A NYFR technology is utilized to intercept the SAR signal. Then, a convergence algorithm with SBL is introduced to recover the sparse vector. Furthermore, simulation results demonstrate the availability and performance of our algorithm.
This paper presents a 6th-order quadrature bandpass delta sigma AD modulator (QBPDSM) with 2nd-order image rejection using dynamic amplifier and noise coupling (NC) SAR quantizer embedded by passive adder for the application of wireless communication system. A novel complex integrator using dynamic amplifier is proposed to improve the energy efficiency of the QBPDSM. The NC SAR quantizer can realize an additional 2nd-order noise shaping and 2nd-order image rejection by the digital domain noise coupling technique. As a result, the 6th-order QBPDSM with 2nd-order image rejection is realized by two complex integrators using dynamic amplifier and the NC SAR quantizer. The SPICE simulation results demonstrate the feasibility of the proposed QBPDSM in 90nm CMOS technology. Simulated SNDR of 76.30dB is realized while a sinusoid -3.25dBFS input is sampled at 33.3MS/s and the bandwidth of 2.083MHz (OSR=8) is achieved. The total power consumption in the modulator is 6.74mW while the supply voltage is 1.2V.
Kyu-Ha SONG San-Hae KIM Woo-Jin SONG
When time difference of arrival (TDOA)-based bearing measurements are used in passive triangulation, the accuracy of localization depends on the geometric relationship between the emitter and the sensors. In particular, the localization accuracy varies with the geometric conditions in TDOA-based direction finding (DF) for bearing measurement and lines of bearing (LOBs) crossing for triangulation. To obtain an accurate estimate in passive triangulation using TDOA-based bearing measurements, we shall use these bearings selectively by considering geometric dilution of precision (GDOP) between the emitter and the sensors. To achieve this goal, we first define two GDOPs related to TDOA-based DF and LOBs crossing geometries, and then propose a new hybrid GDOP by combining these GDOPs for a better selection of bearings. Subsequently, two bearings with the lowest hybrid GDOP condition are chosen as the inputs to a triangulation localization algorithm. In simulations, the proposed method shows its enhancement to the localization accuracy.
Masato WATANABE Junichi HONDA Takuya OTSUYAMA
Multi-static Primary Surveillance Radar (MSPSR) has recently attracted attention as a new surveillance technology for civil aviation. Using multiple receivers, Primary Surveillance Radar (PSR) detection performance can be improved by synthesizing the reflection characteristics which change due to the aircraft's position. In this paper, we report experimental results from our proposed optical-fiber-connected passive PSR system with transmit signal installed at the Sendai Airport in Japan. The signal-to noise ratio of experimental data is evaluated to verify moving target detection. In addition, we confirm the operation of the proposed system using a two-receiver setup, to resemble a conventional multi-static radar. Finally, after applying time correction, the delay of the reflected signal from a stationary target remains within the expected range.
Kyota HATTORI Masahiro NAKAGAWA Masaru KATAYAMA Jun-ichi KANI
The traffic of the future metro network will dynamically change not only in volume but also in destination to support the application of virtualization technology to network edge equipment such as cloud edges to achieve cost-effectiveness. Therefore, the future metro network will have to accommodate traffic cost-effectively, even though both the traffic volume and the traffic destination will change dynamically. To handle to this trend, in this paper, we propose a future metro network architecture based on Next-Generation Passive Optical Network Stage 2 systems that offers cost-effectiveness while supporting virtual machine migration of cloud edges. The basic idea of the proposed method is sharing a burst-mode receiver between the continuous-mode transmitters and burst-mode transmitters. In this paper, we show the feasibility and effectiveness of the proposed method with experiments on prototype systems, and simulations for the preliminary evaluation of network capital expenditure.
Kohei WATABE Toru MANO Takeru INOUE Kimihiro MIZUTANI Osamu AKASHI Kenji NAKAGAWA
Traffic matrix (TM) estimation has been extensively studied for decades. Although conventional estimation techniques assume that traffic volumes are unchanged between origins and destinations, packets are often lost on a path due to traffic burstiness, silent failures, etc. Counting every path at every link, we could easily get the traffic volumes with their change, but this approach significantly increases the measurement cost since counters are usually implemented using expensive memory structures like a SRAM. This paper proposes a mathematical model to estimate TMs including volume changes. The method is established on a Boolean fault localization technique; the technique requires fewer counters as it simply determines whether each link is lossy. This paper extends the Boolean technique so as to deal with traffic volumes with error bounds that requires only a few counters. In our method, the estimation errors can be controlled through parameter settings, while the minimum-cost counter placement is determined with submodular optimization. Numerical experiments are conducted with real network datasets to evaluate our method.
Shuenn-Yuh LEE Cheng-Pin WANG Chuan-Yu SUN Po-Hao CHENG Yuan-Sun CHU
This study proposes a multiple-output differential-input operational transconductance amplifier-C (MODI OTA-C) filter with an impedance scaler to detect cardiac activity. A ladder-type fifth-orderButterworth low-pass filter with a large time constant and low noise is implemented to reduce coefficient sensitivity and address signal distortion. Moreover, linearized MODI OTA structures with reduced transconductance and impedance scaler circuits for noise reduction are used to achieve a wide dynamic range (DR). The OTA-based circuit is operated in the subthreshold region at a supply voltage of 1 V to reduce the power consumption of the wearable device in long-term use. Experimental results of the filter with a bandwidth of 250 Hz reveal that DR is 57.6 dB, and the harmonic distortion components are below -59 dB. The power consumption of the filter, which is fabricated through a TSMC 0.18 µm CMOS process, is lower than 390 nW, and the active area is 0.135 mm2.
By exploiting the inherent sparsity of wireless channels, the channel estimation in an orthogonal frequency division multiplexing (OFDM) system can be cast as a compressed sensing (CS) problem to estimate the channel more accurately. Practically, matching pursuit algorithms such as orthogonal matching pursuit (OMP) are used, where path delays of the channel is guessed based on correlation values for every quantized delay with residual. This full search approach requires a predefined grid of delays with high resolution, which induces the high computational complexity because correlation values with residual at a huge number of grid points should be calculated. Meanwhile, the correlation values with high resolution can be obtained by interpolation between the correlation values at a low resolution grid. Also, the interpolation can be implemented with a low pass filter (LPF). By using this fact, in this paper we substantially reduce the computational complexity to calculate the correlation values in channel estimation using CS.
Takashi MAEHATA Suguru KAMEDA Noriharu SUEMATSU
The 1-bit digital radio frequency (DRF) transmitter using a band-pass delta-sigma modulator (BP-DSM) can output a radio frequency (RF) signal carrying a binary data stream with a constant data rate regardless of the carrier frequency, which makes it possible to transmit RF signals over digital optical links with a constant bit rate. However, the optical link requires a line coding, such as 8B10B or 64B66B, to constrain runlength and disparity, and the line coding corrupts the DRF power spectrum owing to additional or encoded data. This paper proposes a new line coding for BP-DSM, which is able to control the runlength and the disparity of the 1-bit data stream by adding a notch filter to the BP-DSM that suppresses the low frequency components. The notch filter stimulates the data change and balances the direct current (DC) components. It is demonstrated that the proposed line coding shortens the runlength from 50 bits to less than 8 bits and reduces the disparity from several thousand bits to 5 bits when the 1-bit DRF transmitter outputs an LTE signal with 5 MHz bandwidth, when using carrier frequencies from 0.5GHz to 2GHz and an output power variation of 60dB.
Xuewan ZHANG Wenping GE Xiong WU Wenli DAI
Sparse code multiple access (SCMA) based on the message passing algorithm (MPA) for multiuser detection is a competitive non-orthogonal multiple access technique for fifth-generation wireless communication networks Among the existing multiuser detection schemes for uplink (UP) SCMA systems, the serial MPA (S-MPA) scheme, where messages are updated sequentially, generally converges faster than the conventional MPA (C-MPA) scheme, where all messages are updated in a parallel manner. In this paper, the optimization of message scheduling in the S-MPA scheme is proposed. Firstly, some statistical results for the probability density function (PDF) of the received signal are obtained at various signal-to-noise ratios (SNR) by using the Monte Carlo method. Then, based on the non-orthogonal property of SCMA, the data mapping relationship between resource nodes and user nodes is comprehensively analyzed. A partial codeword transmission of S-MPA (PCTS-MPA) with threshold decision scheme of PDF is proposed and verified. Simulations show that the proposed PCTS-MPA not only reduces the complexity of MPA without changing the bit error ratio (BER), but also has a faster convergence than S-MPA, especially at high SNR values.
Kohei TERASHIMA Kazuhiro WAKO Yasuyuki FUJIHARA Yusuke AOYAGI Maasa MURATA Yosei SHIBATA Shigetoshi SUGAWA Takahiro ISHINABE Rihito KURODA Hideo FUJIKAKE
We have developed the high speed bandpass liquid crystal filter with narrow full width at half maximum (FWHM) of 5nm for real-time multi spectral imaging systems. We have successfully achieved short wavelength-switching time of 30ms by the optimization of phase retardation of thin liquid crystal cells.
For more flexible and efficient use of radio spectrum, reconfigurable RF devices have important roles in the future wireless systems. In 5G mobile communications, concurrent multi-band operation using new SHF bands is considered. This paper presents a new configuration of dual-band SHF BPF consisting of a low SHF three-bit reconfigurable BPF and a high SHF BPF. The proposed dual-band BPF employs direct parallel connection without additional divider/combiner to reduce circuit elements and simplify the BPF. In order to obtain a good isolation between two passbands while achieving a wide center frequency range in the low SHF BPF, input/output impedances and external Qs of BPFs are analyzed and feedbacked to the design. A high SHF BPF design method with tapped transmission line resonators and lumped-element coupling is also presented to make the BPF compact. Two types of prototypes; all inductor-coupled dual-band BPF and C-L-C coupled dual-band BPF were designed and fabricated. Both prototypes have low SHF reconfigurable center frequency range from 3.5 to 5 GHz as well as high SHF center frequency of 8.5 GHz with insertion loss below 2.0 dB.
Jingjing SI Jing XIANG Yinbo CHENG Kai LIU
Generalized approximate message passing (GAMP) can be applied to compressive phase retrieval (CPR) with excellent phase-transition behavior. In this paper, we introduced the cartoon-texture model into the denoising-based phase retrieval GAMP(D-prGAMP), and proposed a cartoon-texture model based D-prGAMP (C-T D-prGAMP) algorithm. Then, based on experiments and analyses on the variations of the performance of D-PrGAMP algorithms with iterations, we proposed a 2-stage D-prGAMP algorithm, which makes tradeoffs between the C-T D-prGAMP algorithm and general D-prGAMP algorithms. Finally, facing the non-convergence issues of D-prGAMP, we incorporated adaptive damping to 2-stage D-prGAMP, and proposed the adaptively damped 2-stage D-prGAMP (2-stage ADD-prGAMP) algorithm. Simulation results show that, runtime of 2-stage D-prGAMP is relatively equivalent to that of BM3D-prGAMP, but 2-stage D-prGAMP can achieve higher image reconstruction quality than BM3D-prGAMP. 2-stage ADD-prGAMP spends more reconstruction time than 2-stage D-prGAMP and BM3D-prGAMP. But, 2-stage ADD-prGAMP can achieve PSNRs 0.2∼3dB higher than those of 2-stage D-prGAMP and 0.3∼3.1dB higher than those of BM3D-prGAMP.