We propose an architecture for a 1-bit band-pass delta-sigma modulator (BP-DSM) that outputs concurrent multiband RF signals. The proposed BP-DSM consists of parallel bandpass filters (BPFs) in the feedback loop to suppress the quantization noise at each target frequency band while maintaining the stability. Each BPF is based on second-order parallel infinite impulse response (IIR) filters. This architecture can unify and reconfigure the split BPFs according to the number of bands. The architecture complexity is proportional to the bandwidth of each RF signal and is independent of the carrier spacing between the bands. The conventional architecture of a concurrent multiband digital modulator, reported previously, has multiple input ports to the dedicated BPF at each band and so it cannot be efficiently integrated. Measurements show that the proposed architecture is feasible for transmitting a concurrent dual-band and a triple-band by changing the 1-bit digital data stream while keeping a data transmission rate of 10Gb/s. We demonstrate that the proposed architecture outputs the signal with LTE intra-band and inter-band carrier aggregation on 0.8GHz, 2.1GHz and 3.5GHz, each with 40MHz bandwidth in 120MHz aggregated bandwidth, whose bandwidth surpasses the bandwidth with carrier aggregation of LTE-A up to 100MHz. Adjacent channel leakage ratios of -49dBc and -46dBc are achieved at 3.5GHz in the concurrent dual-band and triple-band, respectively.

The 1-bit band-pass delta-sigma modulator (BP-DSM) achieves high resolution by using the oversampling technique. This method allows direct RF signal transmission from a digitally modulated signal, using a 1-bit digital pulse train. However, it has been previously reported that the adjacent channel leakage ratio (ACLR) in a target frequency band degrades due to the pulse transition mismatch between rising and falling waveforms in the time domain. This paper clarifies that the spurious distortion in BP-DSM is caused by the asymmetricity of the waveform about the center of an eye pattern in the time axis, and proposes a 1-bit BP-DSM with the compensator consisting of a fractional delay filter and a binary data differentiator to cancel out the asymmetry in the target frequency band. This can accurately provide a wideband cancellation signal with more than 100MHz bandwidth, including the adjacent channel, within 50dB power dynamic range. Using long term evolution (LTE) signals with 5MHz bandwidth at 0.8GHz, we simulated the spurious distortion, performing various combinations of rising and falling times in the eye pattern, and the proposed 1-bit BP-DSM always achieved high ACLR, up to 60dB, in 140MHz bandwidth, under all conditions.

60GHz wireless communication requires analog baseband circuits having a bandwidth of about 1GHz. This paper presents a wide bandwidth current-mode low pass filter technique which involves current amplifiers, resistors and capacitors. The proposed current-mode filter is obtained by replacing an integrator employing an op-amp with another integrator employing a current amplifier. With the low input impedance current amplifier having little variation of the input impedance, the proposed filter is expected to improve linearity and power efficiency. The proposed current amplifier which employs super source follower topology with complementary input is suitable for the filter because of its class AB operation. Although simulation results shows the conventional current amplifier which employs super source follower topology without the complementary input has 12Ω variation and 30Ω input impedance, the proposed current amplifier has 1Ω variation and 21Ω input impedance. A fourth order 1GHz bandwidth filter which involves the proposed current amplifiers is designed in a 65nm CMOS technology. The filter can achieve IIP3 of 1.3dBV and noise of 0.6mVrms with power consumption of 13mW under supply voltage of 1.2V according to simulation results with layout parasitic extraction models. Active area of the filter is 380μm×170μm.

This paper presents accurate DC and high frequency power-supply rejection (PSR) models for low drop-out (LDO) regulators using different types of active loads and pass transistors. Based on the proposed PSR model, we suggest design guidelines to achieve a high DC PSR or flat bandwidth (BW) by choosing appropriate active loads and pass transistors. Our PSR model captures the intricate interaction between the error amplifiers (EAs) and the pass devices by redefining the transfer function of the LDO topologies. The accuracy of our model has been verified through SPICE simulation and measurements. Moreover, the measurement results of the LDOs fabricated using the 0.18 µm CMOS process are consistent with the design guidelines suggested in this work.

In this paper, a miniaturized absorptive/transmissive radome with switchable passband and wide absorbing band is designed. Pin diodes are loaded on the radome in order to obtain switchable passband and miniaturized unit cells, while the resistor loaded double square loops are used to absorb the incident wave. The total thickness of the radome is only 4.5mm. Its transmission and absorbing properties are verified by both synthetic experiments and measurements in the anechoic chamber. Furthermore, the switchable passband of the radome is also evaluated using a waveguide simulator.

The performance of devices based on two dimensional (2D) materials is significantly affected upon prolonged exposure to atmosphere. We analyzed time based environmental degradation of electrical properties of HfS2 field effect transistors. Atmospheric entities like oxygen and moisture adversely affect the device surface and reduction in drain current is observed over period of 48 hours. Two corrective measures, namely, PMMA passivation and vacuum annealing, have been studied to address the diminution of current by contaminants. PMMA passivation prevents the device from environment and reduces the effect of Coulomb scattering. Improvement in current characteristics signifies the importance of dielectric passivation for 2D materials. On the other hand, vacuum annealing is useful in removing contaminants from the affected surface. In order to figure out optimum process conditions, properties have been studied at various annealing temperatures. The improvement in drain current level was observed upon vacuum annealing within optimum range of annealing temperature.

A linear-correction method is developed for source position and velocity estimation using time difference of arrival (TDOA) and frequency difference of arrival (FDOA) measurements. The proposed technique first obtains an initial source location estimate using the first-step processing of an existing algebraic algorithm. It then refines the initial localization result by estimating via weighted least-squares (WLS) optimization and subtracting out its estimation error. The new solution is shown to be able to achieve the Cramer-Rao lower bound (CRLB) accuracy and it has better accuracy over several benchmark methods at relatively high noise levels.

We propose a pre-filtering system for blind equalization in order to separate orthogonal frequency division multiplexing (OFDM) symbols in a multiple-input multiple-output (MIMO) - OFDM system. In a conventional blind MIMO-OFDM equalization without the pre-filtering system, there is a possibility that originally transmitted streams are permutated, resulting in the receiver being unable to retrieve desired signals. We also note that signal permutation is different for each subcarrier. In order to solve this problem, each transmitted stream of the proposed MIMO-OFDM system is pre-filtered by a unique allpass filter. In this paper, the pre-filter is referred to as transmit tagging filter (TT-Filter). At a receiver, an inverse filter of the TT-filter is used to blindly equalize a MIMO channel without permutation problem. Further, in order to overcome the issue of phase ambiguity, this paper introduces blind phase compensation.

The Android pattern unlock is a widely adopted graphical password system that requires a user to draw a secret pattern connecting points arranged in a grid. The theoretical security of pattern unlock can be defined by the number of possible patterns. However, only upper bounds of the number of patterns have been known except for 3×3 and 4×4 grids for which the exact number of patterns was found by brute-force enumeration. In this letter, we present the first lower bound by computing the minimum number of visible points from each point in various subgrids.

Anonymous password-based authentication protocols are designed to provide not only password-based authentication but also client anonymity. In [22], Qian et al. proposed a simple anonymous password-based authentication protocol (SAPAKE). In this paper, we reconsider the SAPAKE protocol [22] by first showing that an (third party) active attacker can impersonate the server and compute a session key with probability 1. After giving a formal model that captures such attacks, we propose a simple and secure anonymous password-based authentication (for short, S2APA) protocol that provides security against modification attacks on protocol-specific values and is more efficient than YZWB09/10 [32], [33] and SAPAKE [22]. Also, we prove that the S2APA protocol is AKE-secure against active attacks as well as modification attacks under the computational Diffie-Hellman problem in the random oracle model, and provides unconditional client anonymity against a semi-honest server, who honestly follows the protocol.

We prepared alumina passivation films for p-type silicon substrates by sol-gel wet process mainly using aluminum isopropoxide (Al(O-i-Pr)3) as a precursor material. The precursor solution was spin-coated onto p-type silicon substrates and then calcined for 1 hour in air. Minority carrier lifetime of the passivated wafers was evaluated for different calcination temperature conditions. We also compared the passivation quality of the alumina passivation films using different alumina precursor, aluminum acetylacetonate (Al(acac)3). Obtained effective minority carrier lifetime indicated that the lifetime is strongly depends on the calcination temperature. The substrate calcined below 400°C shows relatively short lifetime below 100 µsec. On the other hand, the substrate calcined around 500°C to 600°C indicates lifetime from 250 to 300 µsec. Calcination temperature dependence of the lifetime for the samples using Al(O-i-Pr)3 precursors shows almost the same as that using Al(acac)3.

We fabricated silicon solar cells with spin-coated sol-gel alumina passivation layers on the rear side. Spin-coated alumina passivation films have moderate passivation quality and are inferior to atomic layer deposited passivation films. However, low-cost and low temperature process of the sol-gel deposition is still beneficial for the cells using commercially available Cz silicon wafers. Thus, we consider an applicability of the spin-coated alumina passivation layer for rear side passivation. Dependence of cell efficiency on contact spacing and contact diameter of a rear electrode was investigated by both experiments and numerical calculation. The experimental results indicated that conversion efficiency of the cell is enhanced from 9.1% to 11.1% by optimizing an aperture ratio and contact spacing of the rear passivation layers. Numerical calculation indicated that small contact diameter with low aperture ratio of a rear passivation layer is preferable to achieve good cell performance in our experimental condition. We confirmed the effectivity of the spin-coated alumina passivation films for rear surface passivation of the low-cost silicon solar cells.

This paper presents a scheme that digitally cancels the unwanted phase components generated by the transmitter's laser and the receiver's local oscillator laser; such components place a substantial limit on the performance of coherent transceivers monolithically integrated with lasers in a photonic integrated circuit (PIC). Our cancellation proposal adopts the orthogonal polarization approach to provide a reference that is uncorrelated with the data signal. We elaborate on the principle of our proposal and its digital signal processing (DSP) algorithm. Experiments on a VCSEL with a linewidth of approximately 300MHz verify that our proposal can overcome the inherent phase noise limitations indicated by simulations and experiments. Our cancellation algorithm in conjunction with CMA-based polarization control is demonstrated and evaluated to confirm the feasibility of our proposal. The achievement of greatly relaxed laser linewidth will offer a significant benefit in offsetting the technical and cost requirements of coherent transceiver PICs with lasers. Therefore, our cancellation proposal is an enabling technology for the successful deployment of future coherent-based passive optical network (PON) systems.

The Android pattern unlock is a popular graphical password scheme, where a user is presented a 3×3 grid and required to draw a pattern on the onscreen grid. Each pattern is a sequence of at least four contact points with some restrictions. Theoretically, the security level of unlock patterns is determined by the size of the pattern space. However, the number of possible patterns is only known for 3×3 and 4×4 grids, which was computed by brute-force enumeration. The only mathematical formula for the number of possible patterns is a permutation-based upper bound. In this article, we present an improved upper bound by counting the number of “visible” points that can be directly reached by a point.

Many important problems in communication networks, transportation networks, and logistics networks are solved by the minimization of cost functions. In general, these can be complex optimization problems involving many variables. However, physicists noted that in a network, a node variable (such as the amount of resources of the nodes) is connected to a set of link variables (such as the flow connecting the node), and similarly each link variable is connected to a number of (usually two) node variables. This enables one to break the problem into local components, often arriving at distributive algorithms to solve the problems. Compared with centralized algorithms, distributed algorithms have the advantages of lower computational complexity, and lower communication overhead. Since they have a faster response to local changes of the environment, they are especially useful for networks with evolving conditions. This review will cover message-passing algorithms in applications such as resource allocation, transportation networks, facility location, traffic routing, and stability of power grids.

Design of lumped-element immittance inverters which support dual-frequency operation and tuning of both operational frequencies is presented. Unique properties of the dual-composite right/left-handed transmission lines (D-CRLH TL) give an opportunity to design immittance inverters with two non-multiple operational frequencies and a stop band between them. Replacement of capacitors of D-CRLH TL unit cells with variable ones enables inverter tunability. Tunability analysis of such immittance inverters is given. It is shown that a tuning range of the operational frequencies is limited by a tolerable variation of the inverter parameter. The design concept is verified by results of electromagnetic simulation and measured frequency characteristics of fixed (non-tunable) as well as tunable dual-frequency immittance inverters and dual-band filters using the inverters.

This paper proposes a new and simple microstrip bandpass filter structure for the design of a fully canonical transversal array filter. The filter is constructed by the parallel arrangement of microstrip even- and odd-mode half-wavelength resonators. In this filter, transmission zeros (TZs) are not produced by cross couplings used in conventional filter designs, but by an intrinsic negative coupling of the odd-mode resonators having open ends with respect to the even-mode resonators with shorted ends. Thus, the control of the resonant frequency and the external Q factor of each resonator makes it possible to form both a specified passband and TZs. As an example, a fully canonical bandpass filter with 2-GHz center frequency, 6% bandwidth, and four TZs is synthesized with a coupling-matrix optimization, and its structural parameters are designed. The designed filter achieves a rapid roll-off and low-loss passband response, which can be confirmed numerically and experimentally.

This paper proposes an opamp-free solution to implement single-phase-clock controlled noise shaping in a SAR ADC. Unlike a conventional noise shaping SAR ADC, the proposal realizes noise shaping by charge redistribution, which is a passive technique. The passive implementation has high power efficiency. Meanwhile, since the proposal maintains the basic architecture and operation method of a traditional SAR ADC, it retains all the advantages of a SAR ADC. Furthermore, noise shaping helps to improve the performance of SAR ADC and relaxes its non-ideal effects. Designed in a 65-nm CMOS technology, the prototype realizes 58-dB SNDR based on an 8-bit C-DAC at 50-MS/s sampling frequency. It consumes 120.7-µW power from a 0.8-V supply and achieves a FoM of 14.8-fJ per conversion step.

A triplexer is presented by using bandpass filters (BPFs) which consist of two-stage of wideband resonator and additional open-circuited stubs. The resonator is firstly proposed by using a coupled-line and an inductive element loaded transmission line. This resonator produces the wide passband by a dual-mode resonance, high attenuation level at stopbands, and the steepness at the edge of the passband due to the attenuation poles. In order to understand the behavior of the resonator, the conditions for resonances and attenuation poles are especially solved and their current densities are analyzed by an electromagnetic simulation. Secondly, three types of wideband BPFs are constituted and finally a wideband triplexer is composed by using these BPFs. The basic characteristics of the proposed BPFs and the matching methodology enable to realize the triplexer whose desired passbands are around 3.1-5.1 GHz, 5.85-7.85 GHz, and 8.6-10.6 GHz with high isolation performance at the other passbands. The proposed triplexer is predominance in the flexible bandwidth or wide operating frequency range. All the BPFs and the triplexer are implemented on a planar printed circuit board assuming the use of the microstrip line structure.

A compact millimeter-wave three-pole dual-band bandpass filter (BPF) by using substrate-integrated waveguide (SIW) dual-mode cavities is developed in this paper. The proposed filter consists of three SIW dual-mode cavities, in which the TE201 and TE102 modes are used to form two passbands. The center frequencies of the two passbands can be readily changed by varying the lengths and/or widths of the SIW cavities. Meanwhile three transmission zeros are produced with appropriate design of the input and output of the SIW cavities, which increase significantly the isolation between the two passbands and their roll-off rate of attenuations. The dual-band BPF filter is designed, fabricated and measured. The measured center frequencies of the two passbands are 26.75GHz and 31.55GHz, respectively. The 3dB-passbands are 26.35-27.15GHz (3%) and 31.29-31.81GHz (1.6%), respectively, with maximum insertion loss of 2.64dB and 4.2dB, respectively, and return loss larger than 12dB in both passbands. A good agreement between the simulated and measured filter characteristics is obtained.