A transceiver employing hierarchical constellation encodes two hierarchies with different levels of protection and selectively decodes one or both of them, resulting in constellation inconsistency of encoding and decoding. Therefore, a conventional ordered successive interference cancellation (OSIC) receiver, which restores the signals as they are transmitted, can not be compatible with the constellation inconsistency. To mitigate this problem, an OSIC detector with the individual received bit rate per data stream is first designed. To further improve the error performance, the proposed detector is modified, for which distinct criteria are used for demodulation and cancellation. It is shown that the proposed detector achieves spectrally efficient detection while guaranteeing reliable communication.

In this letter, we develop a behavioral metric with which spamming botnets can be quickly identified with respect to their residing IP blocks. Our method aims at line-speed operation without deep inspection, so only TCP/IP header fields of the passing packets are examined. However, the proposed metric yields a high-quality receiver operating characteristics (ROC), with high detection rates and low false positive rates.

This paper proposes a new multi-band received signal strength (MRSS) fingerprinting based indoor location system, which employs the frequency diversity on the conventional single-band received signal strength (RSS) fingerprinting based indoor location system. In the proposed system, the impacts of frequency diversity on the enhancements of positioning accuracy are analyzed. Effectiveness of the proposed system is proved by experimental approach, which was conducted in non line-of-sight (NLOS) environment under the area of 103 m2 at Yagami Campus, Keio University. WLAN access points, which simultaneously transmit dual-band signal of 2.4 and 5.2 GHz, are utilized as transmitters. Likewise, a dual-band WLAN receiver is utilized as a receiver. Signal distances calculated by both Manhattan and Euclidean were classified by K-Nearest Neighbor (KNN) classifier to illustrate the performance of the proposed system. The results confirmed that Frequency diversity attributions of multi-band signal provide accuracy improvement over 50% of the conventional single-band.

Cooperative relaying (CR) is a promising technique to provide spatial diversity by combining multiple signals from source and relay stations. In the present paper, the impact and use of the asymmetric property in bi-directional CR under asymmetric traffic conditions are discussed assuming that CR involves one communication pair and one relay station in a time division duplex (TDD) system. The asymmetric property means that the average communication quality differs for each transmission direction because of the difference in signal power between the combined signals for each direction. First, numerical results show the asymmetric property of bi-directional CR. Next, in order to evaluate the impact of the asymmetric property, the optimal relay position and resource allocation are compared to those in simple multi-hop relaying, which does not have the asymmetric property. Numerical results show that, in order to maximize the overall quality of bi-directional communication, the optimal relay position in CR depends on the offered traffic ratio, which is defined as the traffic ratio of each transmission direction, while the offered traffic ratio does not affect the optimal relay position in multi-hop relaying. Finally, the asymmetric property is used to enhance the overall quality. Specifically, a high overall quality can be achieved by, for example, opportunistically switching to the transmission direction with higher quality. Under asymmetric traffic conditions, weighted proportionally fair scheduling (WPFS), which is proposed in the context of downlink scheduling in a cellular network, is applied to transmission direction switching. Numerical results reveal that WPFS provides a high overall quality and that the quality ratio is similar to the offered traffic ratio.

A post-wall center-feed waveguide consisting of T-junctions is proposed for reducing the slot-free area of a parallel plate slot array antenna. The width of the slot-free area is reduced from 2.6 λ0 to 2.1 λ0. A sidelobe level in the E-plane is expected to be suppressed lower than that of the conventional center-feed antenna using cross-junctions. The method of moments with solid-wall replacement designs initially the T-junctions and HFSS including the post surfaces modifies only the reflection cancelling post. We have designed and fabricated a 61.25 GHz model antenna with uniform aperture illumination. The sidelobe level in the E-plane is suppressed to -9.5 dB while that of a conventional cross-junction type is -7.8 dB. Also, we suppress it to -13.8 dB by introducing a -8.3 dB amplitude tapered distribution in the array of the radiation slot pairs.

Correction factors are presented for estimating the RF electromagnetic field strength in the compliance assessment of human exposure from an indoor RF radio source in the frequency range from 800 MHz to 3.5 GHz. The correction factors are derived from the increase in the spatial average electric field strength distribution, which is dependent on the building materials. The spatial average electric field strength is calculated using relative complex dielectric constants of building materials. The relative complex dielectric constant is obtained through measurement of the transmission and reflection losses for eleven kinds of building materials used in business office buildings and single family dwellings.

In this paper, we present a new composite transistor circuit design technique that provides superior performance enhancement to analog circuits. By adding a composite transistor to the cascode-compensated amplifier, it has achieved a 102 dB DC gain, and a 37.6 MHz unity gain bandwidth while driving a 2 nF heavy capacitive load at a single 1.8 V supply. In the comparison of power-bandwidth and power-speed efficiencies on figures of merit, it offers significantly high values with respect to the reported state-of-the-art works. By employing the composite transistor in a linear regulator powered by a 3.3 V supply to generate a 1.8 V output voltage, it has shown fast recovery response at various load current transients, having a 1% settling time of 0.1 µS for a 50 mA or 100 mA step, while a 1% settling time of 0.36 µS for a maximum 735 mA step under a capacitive load of 10 µF with a 1 Ω ESR resistor. The simulated load regulation is 0.035% and line regulation is 0.488%. Comparing its results with other state-of-art LDO reported results, it also validates the significant enhanced performance of the proposed composite-transistor-based design in terms of speed, current driving capability and stability against changes in environmental parameters. All the proposed designs are simulated using chartered semiconductor (CSM) 1.8 V/3.3 V 0.18 µm CMOS triple-well process technology with thin/thick oxide options and BSIM3 model parameters.

The aim of this study is to develop a new whole-body averaged specific absorption rate (SAR) estimation method based on the external-cylindrical field scanning technique. This technique is adopted with the goal of simplifying the dosimetry estimation of human phantoms that have different postures or sizes. An experimental scaled model system is constructed. In order to examine the validity of the proposed method for realistic human models, we discuss the pros and cons of measurements and numerical analyses based on the finite-difference time-domain (FDTD) method. We consider the anatomical European human phantoms and plane-wave in the 2 GHz mobile phone frequency band. The measured whole-body averaged SAR results obtained by the proposed method are compared with the results of the FDTD analyses.

Recently, a graph labeling technique based on prime numbers has been suggested for reducing the costly transitive closure computations in RDF query languages. The suggested prime number graph labeling provides the benefit of fast query processing by a simple divisibility test of labels. However, it has an inherent problem that originates with the nature of prime numbers. Since each prime number must be used exclusively, labels can become significantly large. Therefore, in this paper, we introduce a novel optimization technique to effectively reduce the problem of label overflow. The suggested idea is based on graph decomposition. When label overflow occurs, the full graph is divided into several sub-graphs, and nodes in each sub-graph are separately labeled. Through experiments, we also analyze the effectiveness of the graph decomposition optimization, which is evaluated by the number of divisions.

A composite right/left-handed transmission line (CRLH-TL) using substrate integrated waveguide (SIW) with floating-conductor (SIW-type CRLH-TL) for microwave and millimeter wave frequencies has been proposed by the authors. This paper proposes a new configuration that is shield type of the SIW-type CRLH-TL, which can suppress the radiation from the exposed floating-conductors, and shows that even if the shielded structure is used, the SIW-type CRLH-TL supports the LH mode as well as the prototype. Proposed CRLH-TL consists of a SIW with slot apertures (part 1), a dielectric film with floating-conductors (part 2) and a SIW without lower conductor (part 3). A shielded SIW-type CRLH-TL for X--K band (with wide LH mode bandwidth of 6 GHz and transition frequency of 16 GHz) that satisfies the balance condition is designed. Dispersion diagram and S-parameters are derived numerically, and typical field distributions of RH and LH transmission and the zeroth-order resonance are shown. Measured result agrees well with theoretical result, by considering the accuracy performance and loss factors of the fabricated CRLH-TL. Proposed CRLH-TL has advantage of simple manufacturing, because the parts 1--3 are composed of simple planar periodic structure. It is expected to be one of the basic structure of CRLH-TL or components such as LH coupler above 10 GHz or millimeter wave frequency.

The construction of EM absorber and frequency selective shielding has been investigated by using two dimensional metal fiber array (MFA) composites. The MFA composite shows a resonant type frequency dispersion in the complex relative permittivity spectra (εr = εr' - jεr") having a negative εr' region. The frequency characteristics of the conventional ferrite-rubber EM absorber can be improved by combining with the negative permittivity property of the MFA composite. A frequency selective shielding can be achieved by the evanescent EM wave propagation in the layered MFA composite structure.

In order to determine exposure compliance with the electromagnetic fields from a base station's antenna in the far-field region, we should calculate the spatially averaged field value in a defined space. This value is calculated based on the measured value obtained at several points within the restricted space. According to the ICNIRP guidelines, at each point in the space, the reference levels are averaged over any 6 min (from 100 kHz to 10 GHz) for the general public. Therefore, the more points we use, the longer the measurement time becomes. For practical application, it is very advantageous to spend less time for measurement. In this paper, we analyzed the difference of average values between 6 min and lesser periods and compared it with the standard uncertainty for measurement drift. Based on the standard deviation from the 6 min averaging value, the proposed minimum averaging time is 1 min.

Post-wall waveguide slot arrays are potential candidates for millimeter-wave systems. The modeling of the post-walls by the equivalent solid-walls in terms of guided wavelength is indispensable for intensive optimization of slot design for reducing computational load. In the single mode waveguide slot arrays, the modeling errors of the post-wall waveguide by the solid-wall waveguide are serious especially for the transversely located slots. The S-parameter prediction errors become larger as we increase the height of the waveguide to utilize the low-loss advantage of the waveguide. The authors propose a novel post-wall waveguide structure, named as a connected post-wall (C-PW), to enhance the equivalence. The C-PW waveguide keeps enhanced equivalence to the solid-walls even for a larger substrate height. The predictions are confirmed by simulations and measurements. An 8-element linear array of reflection-cancelling slot pairs is designed by using the equivalent solid-wall model to demonstrate the feasibility of the simple design in the C-PW.

A novel analysis model for post-wall waveguide T-junctions is proposed. Equivalent solid-walls for the post-walls to have equal guided wavelength are corrected in the analysis model so that the wall thickness for the coupling windows is set to the difference in the width between the post-wall and the solid-wall waveguides. The accuracy of the proposed model is confirmed by comparing it to an HFSS analysis for the real structure of the post-wall waveguide T-junction including the post surfaces. 61.25 GHz model antennas are fabricated for experimental verification. The reflection of the antenna designed by the modified analysis model is suppressed to below -15 dB over a 5.6 GHz bandwidth, while that in the antenna designed by the conventional model is larger than -15 dB around the design frequency.

Context-aware systems detect user's physical and social contexts based on sensor networks, and provide services that adapt to the user accordingly. Representing, detecting, and managing the contexts are important issues in context-aware systems. Composition of contexts is a useful method for these works, since it can detect a context by automatically composing small pieces of information to discover service. Danger-aware services are a kind of context-aware services which need description of relations between a user and his/her surrounding objects and between users. However when applying the existing composition methods to danger-aware services, they show the following shortcomings that (1) they have not provided an explicit method for representing composition of multi-user' contexts, (2) there is no flexible reasoning mechanism based on similarity of contexts, so that they can just provide services exactly following the predefined context reasoning rules. Therefore, in this paper, we propose a two-stage composition method based on context similarity to solve the above problems. The first stage is composition of the useful information to represent the context for a single user. The second stage is composition of multi-users' contexts to provide services by considering the relation of users. Finally the danger degree of the detected context is computed by using context similarity between the detected context and the predefined context. Context is dynamically represented based on two-stage composition rules and a Situation theory based Ontology, which combines the advantages of Ontology and Situation theory. We implement the system in an indoor ubiquitous environment, and evaluate the system through two experiments with the support of subjects. The experiment results show the method is effective, and the accuracy of danger detection is acceptable to a danger-aware system.

Chinese new words and their part-of-speech (POS) are particularly problematic in Chinese natural language processing. With the fast development of internet and information technology, it is impossible to get a complete system dictionary for Chinese natural language processing, as new words out of the basic system dictionary are always being created. A latent semi-CRF model, which combines the strengths of LDCRF (Latent-Dynamic Conditional Random Field) and semi-CRF, is proposed to detect the new words together with their POS synchronously regardless of the types of the new words from the Chinese text without being pre-segmented. Unlike the original semi-CRF, the LDCRF is applied to generate the candidate entities for training and testing the latent semi-CRF, which accelerates the training speed and decreases the computation cost. The complexity of the latent semi-CRF could be further adjusted by tuning the number of hidden variables in LDCRF and the number of the candidate entities from the Nbest outputs of the LDCRF. A new-words-generating framework is proposed for model training and testing, under which the definitions and distributions of the new words conform to the ones existing in real text. Specific features called "Global Fragment Information" for new word detection and POS tagging are adopted in the model training and testing. The experimental results show that the proposed method is capable of detecting even low frequency new words together with their POS tags. The proposed model is found to be performing competitively with the state-of-the-art models presented.

In this letter, a new CCM material, adding Ni powder to a conventional CCM, for X-band applications is designed and analyzed to improve the SE. To obtain the SE of the fabricated CCM accurately, material constants of the CCM of the permittivity and permeability were extracted using transmission/reflection measurements. Using the material constants derived from the measurement, the SE was calculated and the results were verified using a commercial full-wave three-dimensional electromagnetic wave simulator. The SE of the proposed the CCM was improved by approximately 4 dB in the X band compared to that of a conventional CCM. The CCM proposed in this paper can be applied as a shielding material as well as for housing of various communication systems and electrical instruments.

In ubiquitous sensor networks, the estimation accuracy of a node location is limited due to the presence of non-line-of-sight (NLOS) paths. To mitigate the NLOS effects, this letter proposes a simple algorithm where NLOS identification is carried out using angle-of-arrival (AOA). Simulation results show that the use of AOA improves NLOS identification rates and location estimation accuracy.

A new signature scheme of MPKC is proposed. It is created by perturbing a traditional encryption scheme in two ways. The proposed perturbation polynomials successfully reinforce the Matsumoto-Imai cryptosystem This new signature scheme has a structure very difficult to cryptanalyze. Along with the security against algebraic attacks, its security against existing attacks is discussed. The experimental data imply that the scheme can create a both lightweight and secure signature system.

A HfO2 as the charge-storage layer with the physical thickness thinner than 4 nm in silicon-oxide-high-k oxide-oxide-silicon (SOHOS) flash memory was investigated. Compared to the conventional silicon-oxide-nitride-oxide-silicon (SONOS) flash memory, the SOHOS shows the slow operational speed and exhibits the poorer retention characteristics. These are attributed to the thin physical thickness below 4 nm and the crystallization of the HfO2 to contribute the lateral migration of the trapped charge in the trapping layer during high temperature annealing process.