Direct sequence code division multiple access (DS-CDMA) is attractive for mobile radio use because of its inherently high capacity. There is great demand for mobile radio to offer multimedia services. This means that various service rates and qualities should be supported. DS-CDMA systems are flexible and can accommodate various user rates easily so these demands can be met. As many users will occupy the same frequency band simultaneously, the traffic capacity of a DS-CDMA system is determined by interference power. Interference cancellation is one of the important techniques in decreasing interference power at the demodulation stage and thus increasing traffic capacity. In this paper, we propose the delayed symbol combining interference canceller which can suppress the interference from various users sending at different information rates. Performance of the proposed method is calculated by computer simulations. Furthermore, the effect of adding forward error correction to the proposed canceller is also evaluated by computer simulations. In the quasi static flat fading environment, it is found that the Eb/No degradation due to interference is suppressed to 3 dB at BER=10-3 with 24 users. In the quasi static frequency selective fading environment, it is found that the required Eb/No of the frequency selective fading canceller is about 11 dB better than that of the flat fading canceller for the target BER of 10-3. It is found that BER<10-3 is achieved with forward error correction and bit interleaving even when the maximum Doppler frequency normalized by low data bit rate is 0. 0008 and Eb/No is 20 [dB] in frequency selective fading and 30 [dB] in flat fading.

In multilevel block modulation codes for QPSK and 8-PSK modulation, a construction of binary component codes is given. These codes have a good minimum Euclidean distance by using different forms of the dependency properties of the binary component codes. Interdependency among component codes is formed by using the binary component subcodes which are derived by the coset decomposition of the binary component codes. The algebraic structures of the codes are investigated to find out how interdependency among component codes gives a good minimum Euclidean distance. First, it is shown that cyclic codes over ZM for M-PSK (M=4,8), where the coding scheme is given by Piret, can be constructed by forming specific interdependency among binary component codes for proposed multilevel coding method. Furthermore, it is shown that better minimum Euclidean distance than above can be obtained by modifying the composition of interdependency among binary component codes. These proposed multilevel codes have algebraic structure of additive group and cyclic property over GF(M). Finally, error performances are compared with those of some code's reference modulation scheme for transmitting the same number of information bits.

This paper presents a design of CMOS Chua-type analog chaos circuit by using a signal-flow-graph (SFG) method. In this circuit, the transmittance of a nonlinear element is realized by an OTA with a feedback resistor, and other linear elements are realized by op-amp based circuits. The proposed circuit is insensitive to the finite admittance of OTA's and to the parasitics of resistors except a feedback resistor in the nonlinear element. The performance and chaotic behavior of the proposed circuit are confirmed by SPICE simulations.

A single-chip GaAs Transmit/Receive (T/R)-MMIC front-end has been developed which is applicable to 1. 9-GHz personal communication terminals such as digital cordless phones. This chip is fabricated using a planar self-aligned gate FET useful for low-cost and high-volume production. The chip integrates RF front-end analog circuits a power amplifier, a T/R-switch, and a low-noise amplifier. Additionally integrated are a newly developed voltage-doubler negative-voltage generator (VDNVG) and a control logic circuit to control transmit and receive functions, enabling both a single-voltage operation and an enhanced power handling capability of the switch, even under a single low-voltage supply condition of 2 V. The power amplifier incorporated onto the chip is capable of delivering a 21 dBm output power at a 39% efficiency, and a 30 dB associated gain with a 2 V single power supply in the transmit mode. The gain and efficiency are higher than those of the previously reported amplifier operating with a 2 V single power supply. The VDNVG produces a step-up voltage of 2. 9 V as well as a negative voltage of -1. 8 V from a 2 V power supply, operating with a charge time of less than 0. 25 µs. The control logic circuit on the chip has a newly designed interface circuit utilizing the step-up voltage and negative voltage, thereby enabling the chip to handle high power outputs over 24 dBm with a low operating voltage of 2 V. In the receive mode, a 1. 7 dB noise figure and a 0. 6 dB insertion loss are achieved with a current dissipation of 3. 6 mA. The developed MMIC, which is the first reported 2 V single-voltage operation T/R-MMIC front-end, is expected to contribute to the size and weight reductions in personal communication terminals.

MTDMA (Multimedia, Multimode TDMA) system has been developed for the 3rd generation mobile communications. An adaptive modulation technique is employed, which select 16 QAM or QPSK modulations fit for the O (Indoor Office)/P (Outdoor to Indoor and Pedestrian) communication environments. The maximum user rate of 4 Mbps is realized. Basic specification is described for O, P and V environments.

This paper compares the BER performance of two types of pilot channel-based coherent Rake combining achievable by the use of weighted multi-slot averaging (WMSA) channel estimation filter in DS-CDMA transmission links. One is for the time-multiplexed pilot channel and the other is for the parallel pilot channel. The WMSA channel estimation filter weights and averages the received pilot over a period of several slots to improve the BER performance. We propose the WMSA channel estimation filters for time-multiplexed pilot and parallel pilot structures. Achievable BER performance under frequency-selective fading environments is computer simulated. The simulation results show that almost same BER performance can be achieved for both pilot channel structures when the same energy is allocated to the pilot.

This paper proposes the Dual Zipfian Model addressing how to describe HTTP access trends in large-scale data communication networks, and discusses how to design the capacity of address cache tables in an edge router of the networks. We show that destination addresses of packets can be characterized by two types of Zipf's law. Fundamental concept of the Dual Zipfian Model is in complementary use of these laws, and we can derive the relationship between the number of accesses and the number of destination addresses. Experimental results show that the relation gives a good approximation. Applying this relation, we derive cache hit probabilities of the address cache table that incorporates high-speed address resolution. Using the probabilities, design issues including the capacity of the cache tables and aging algorithms of cache entries are also discussed.

For usage in fading environments, the idea of utilizing radio signal processing with software programmable devices promises greater flexibility and functionality. However, to realize these benefits very high performance DPSs and AD converters are required, especially for adaptive antennas with CDMA. One potential method of reducing the implementation complexity is to employ multicarrier (MC) modulation as it allows parallel signal processing in addition to its benefits in combating fading and ISI effects. This paper proposes a system utilizing MC DS/CDMA and a recursive adaptive array antenna processing algorithm for estimating the array response vector (array manifold) and hence the optimal weights. In order to evaluate this system performance results obtained through computer simulations are presented. The proposed MC system improves the accuracy of the direction-of-arrival (DOA) estimation of the signal by 2 degrees as compared with a single carrier system. It is also shown that the proposed adaptive array antenna algorithm for MC DS/CDMA reduces the number of iterations of the power method significantly and allows parallel processing of the adaptive algorithm.

Performance of optical asynchronous code-division multiple-access (CDMA) systems with double optical hard-limiters is analyzed in the presence of avalanche photodiode (APD) noise and thermal noise. Optical orthogonal codes (OOC's) are employed as signature sequence codes. In the analysis, chips are assumed to be synchronous among users: the chip synchronous case. Thus, the performance results in the upper bound on the performance of the asynchronous system. The results show that the optical asynchronous CDMA systems with double optical hard-limiters have good performance in the presence of the APD noise and the thermal noise even when the number of simultaneous users is large.

A communication system which attains an efficient amalgamation of base station (BS) type cellular communication and non-BS type direct communication for mobile terminals (MTs), "cellularad-hoc united communication system," is proposed. In this system, whether a cellular system or an ad-hoc communication system is chosen by distance and whether the condition is good or not between communicating MTs. In other words, when two terminals are relatively near each other and are in sufficient conditions to communicate directly, they select the ad-hoc communication, while for other cases they use the cellular system. The proposed system was confirmed to have effective channel usage and low battery consumption from the simulation results. It can be also said that this system is suited especially for MTs which tend to communicate with closer partners such as operational mobile robots and autonomous carrier vehicles.

Two types of CPW-fed active antenna for television receivers, printed on thin dielectric film, are analyzed numerically and experimentally and their broadband operations are reported. The actual gain of the receiving active antenna is expressed in terms of the transducer power gain of the amplifier circuit and the effective length of the passive antenna. Between the feed point of the passive antenna element and the CPW, the silicon transistor 2SC2585 or 2SC3604 is integrated with a dipole antenna or loop antenna. The actual gains of a dipole antenna with 24 cm length are more than 8 dBd (relative gain to the standard half-wave dipole) at frequencies from 470 to 770 MHz for television channels 13-62 in Japan. In the case of a loop antenna with a size of 25. 8 cm12 cm, actual gains of more than 3. 5 dBd are obtained for channels 1-12, from 90 to 222 MHz, and more than 6. 5 dBd for channels 13-62, from 470 to 770 MHz.

The next generation mobile communications systems must support multimedia communications services as well as conventional voice service. DS-CDMA is regarded as the most promising candidate, because it is indispensable to cope with multimedia. The system capacity of DS-CDMA system is limited by the total interference level. As a result, in DS-CDMA systems many users suffer very poor communication quality if the total interference level exceeds this limit. Therefore, this paper considers smoothing interference fluctuation using the difference between voice and data in a type of QoS (quality of service). In other words, voice communication is suitable for a loss system because the quality of voice communication is delay-sensitive. On the other hand, data communication is suitable for a waiting system because the quality of data communication is non-delay-sensitive. This paper focuses on a system that applies a circuit switching method for voice traffic and a reservation type packet switching method for data traffic and proposes a data traffic control method. In this proposed data traffic control method, a base station controls data transmission from a mobile station to utilize unused voice traffic resources. As a result, the proposed method achieves highly efficient use of the radio spectra by smoothing interference fluctuation in DS-CDMA systems. This paper evaluates the performance level of the proposed method from a system capacity standpoint. It is shown that the proposed method achieves higher system capacity in voice/data integrated transmission.

A RAKE combiner based on a matched filter (MF) can be relatively easily implemented since the despread signal components that have propagated along different paths appear sequentially at the MF output. An important design problem is how to accurately select the paths having sufficiently large signal-to-noise power ratios (SNRs). This paper proposes a simple path selection algorithm that uses two selection thresholds. The first threshold is to select the paths that provide largest SNRs. However, as the total received signal power (sum of the signal powers of all paths) decreases, some of the selected paths become noisy. Therefore, we introduce a second threshold that discards the noisy or noise-only paths from among those selected by the first threshold. We apply the proposed path selection algorithm to a pilot symbol-assisted coherent RAKE combiner and find by computer simulations a near optimum set of the two thresholds in frequency selective multipath Rayleigh fading channels. Several power delay profile shapes are considered. The simulation results demonstrate that the MF-based RAKE combiner with the two selection thresholds can achieve a bit-error-rate (BER) performance close to the ideal case (i. e. , the paths to be used for RAKE combining are selected for each power delay profile such that the required signal energy per information bit-to-noise spectrum density ratio (Eb/N0) is minimized).

To enhance the anti-fading technique of direct sequence code division multiple access (DS/CDMA) schemes in land mobile radio communication systems, a two-dimensional RAKE reception (2D-RAKE) scheme in beam space digital beam forming (BS-DBF) antenna configuration is proposed. The proposed scheme is applied to cellular base stations where the received signals in the reverse link are relieved from multipath fading by means of enhanced RAKE combining in spacial and temporal domains. Fundamental performance in the reverse link under multipath fading environments is investigated by computer simulation applying a wideband propagation channel model.

The Future Public Land Mobile Telecommunication Systems (FPLMTS) standards have made it quite clear that in the near future, the capability in doing wireless data transmission will become necessary in order to make the tether-free use of multimedia applications possible. CDMA is considered the most appropriate and probable radio access method of FPLMTS for its high capacity and flexibility in accommodation of multimedia and variable rate users. In order to further increase the capacity of CDMA system, several techniques have been studied and proposed such as an interference canceller and adaptive array antenna. We propose the novel multi-user detection type interference cancellation technique named SRIC (Symbol Ranking type IC) in this paper. SRIC is very feasible for its small amount of operation compared with other multi-user detection type ICs and can be added to a base station with slight alteration according to the requirement of higher capacity. The performance of SRIC depends on the method of calculating the likelihood. We studied three methods. In order to reduce the operations, we tried to propose two more methods. We confirmed that SRIC can make the system capacity about three times greater than that of a conventional RAKE receiver. We also confirmed that SRIC can be reduce its operations very much at some sacrifice of their performance. There are nine variants of SRIC, which have a trade off between performance and amount of operation. We can choose one of them which is most fit to our requirement. The first operation of SRIC is common with that of a conventional RAKE receiver. Therefore, SRIC can be introduced to conventional systems afterwards by inserting the interference canceller block which functions replica generation, removal, and ranking between output of a RAKE receiver and FEC decoder.

We have improved the optical beam induced resistance change (OBIRCH) system so as to detect (1) a current path as small as 10-50 µA from the rear side of a chip, (2) current paths in silicide lines as narrow as 0. 2 µm, (3) high-resistance Ti-depleted polysilicon regions in 0. 2 µm wide silicide lines, and (4) high-resistance amorphous thin layers as thin as a few nanometers at the bottoms of vias. All detections were possible even in observation areas as wide as 5 mm 5 mm. The physical causes of these detections were characterized by focused ion beam and transmission electron microscopy.

This paper presents a novel transmission diversity scheme for code division multiple access system. Conventional diversity receivers in mobile stations require space and complicated circuits, however, the proposed diversity schemes present significant diversity effect without any diversity equipment at the mobile station. It is possible to use the transmitter diversity at the base station by using the feature of time division duplex (TDD) which has strongly correlated fading patterns in both forward and reverse link. Computer simulation is performed to evaluate the performance of the proposed systems for single user environment. The performance of the system 1, which select best situated antenna, is analyzed and the BER performance for multiple access is presented.

One-dimensional Cellular Automata (CA's) are considered as potential pseudorandom pattern generators to generate highly random parallel patterns with simple hardware configurations. A class of linear, binary, and of nearest neighbor (radius = 1) CA's is referred to here as elementary ones. This paper investigates operations of such CA's with fixed boundary conditions when non-null boundary values are applied to them. By modifying transition matrices of elementary CA's to include the influence of boundary values, structures of state transition diagrams are determined.

Future satellite communication systems will be developed at Ka-band (20/30 GHz) owing to the relatively wide frequency allocation and current freedom from terrestrial interference for multimedia services. A serious disadvantage of the Ka-band, however, is the very high atmospheric attenuation in rainy weather. Quasi-synchronous CDMA drastically reduces the effect of self-noise with several interesting features of CDMA for mobile communications such as flexible frequency reuse, the capability of performing soft-handover and a lower sensitivity to interference. This paper evaluates the performance of a quasi-synchronous CDMA return link for a Ka-band geostationary satellite communication system. For a fixed satellite channel whose characteristics depend on weather conditions, the signal envelope and phase for this channel is modeled as Gaussian. The bit error and outage probability, and the detection loss due to imperfect chip timing synchronization is analytically evaluated and the system capacity degradation due to the weather condition is estimated. Two cases of general and worst conditions are evaluated, in which i) rain attenuation ii) nonlinearity of transponder are considered. The two cases consist of the general case in which all users are affected by rainy weather, and the worst case in which only the user of interest, not multiple access interferers, is affected by rain attenuation. The results for the two cases of rainy weather clearly show that quasi-synchronous CDMA eases the power control requirements and has less sensitivity to imperfect power control. When dealing with the impact of the satellite transponder nonlinearity in addition to the rain attenuation, the shift of optimum amplifier operating point is shown so that [Eb/N0]sat, defined as the sum of the Eb/N0 value required to obtain a BER equal to Pb at a given output backoff (OBO) and the value of the OBO itself, tends to decrease, and higher BER impairment is given, since the rain attenuation results in the same effect as the additive input backoff (IBO) at the satellite transponder input. As the BER increases, the optimum [Eb/N0]sat and IBO decrease that result in the shift of optimum operating point.

Three types of ternary decision diagrams (TDDs) are considered: AND -TDDs, EXOR-TDDs, and Kleene-TDDs. Kleene-TDDs are useful for logic simulation in the presence of unknown inputs. Let N(BDD:f), N(AND-TDD:f), and N(EXOR-TDD:f) be the number of non-terminal nodes in the BDD, the AND-TDD, and the EXOR-TDD for f, respectively. Let N(Kleene-TDD:) be the number of non-terminal nodes in the Kleene -TDD for , where is the regular ternary function corresponding to f. Then N(BDD:f) N(TDD:f). For parity functions, N(BDD:f)=N(AND-TDD:f)=N(EXOR-TDD:f)=N(Kleene-TDD:). For unate functions,N(BDD:f)=N(AND-TDD:f). The sizes of Kleene-TDDs are O(3n/n), and O(n3) for arbitrary functions, and symmetric functions, respectively. There exist a 2n-variable function, where Kleene-TDDs require O(n) nodes with the best order, while O(3n) nodes in the worst order.