Multimedia mobile communication systems with high-speed radio transmission supported by asynchronous transfer mode (ATM) technologies have been intensively studied over the last few years. Smaller radio zones termed microcells and picocells will be used in this kind of mobile communication systems for the purpose of high-speed radio transmission. When the coverage of a radio zone is smaller, the amount of traffic per radio zone is relatively low. It is not possible to use the cable circuits connecting the switch and base stations in an efficient manner because of the lack of the scale effect of traffic. With smaller radio zones, moreover, handoff occurs frequently as a mobile station moves. The switch is required a large capacity to handle the processing of frequent handoffs. This paper proposes a mobile network architecture controlled by the concentrated grouping of base stations. A special feature of this configuration is the ability of the network's switches to efficiently accommodate numerous base stations that control small radio zones. It can also lighten the handoff control load of switches; the effect of handoff frequency reduction is evaluated with computer simulation.

This paper proposes a group synchronization mechanism which synchronizes slave destinations with the master destination for stored media in multicast communications. At the master and slave destinations, an intra-stream and an inter-stream synchronization mechanisms which were previously proposed by the authors are employed to output the master media stream and slave media streams synchronously. We achieve group synchronization by adjusting the output timing of the master media stream at each slave destination to that at the master destination. We also deal with control of joining an in-progress multicast group. The paper presents experimental results using an interconnected ATM-Ethernet LAN, which is a kind of heterogeneous network. In our experimental system, stored voice and video streams are multicast from a source to plural destinations distributed among distinct networks, and then they are synchronized and output. Furthermore, the paper demonstrates the effectiveness of the mechanism.

We address, in this paper, the main features of hybrid modes propagating in a rectangular waveguide partially filled with pseudochiral Ω-slabs. For the particular case of a uniaxial Ω-slab, we show that LSE and LSM hybrid modes can propagate in this inhomogeneously filled rectangular waveguide. The influence of the Ω-parameter, which characterizes the magnetoelectric tensors of the bianisotropic slab, on LSM modes is analyzed--namely an increase in the bandwidth for monomodal operation is reported. In addition, a field displacement effect and a variable phase shift proportional to the change of the Ω-parameter are attained. Finally, it is shown that the propagation characteristics are independent of the direction of propagation and so, unlike the case of magnetically biased ferrite loading, reciprocal devices can be achieved.

The concept of controlled resource sharing and dynamic quality of service (QoS) on the next generation Internet has attracted much attention recently. It is suggested that, by imposing real-time revision of shared resource allocated to individual media streams or data flows according to user/application QoS demand and resource availability, more balanced and efficient multimedia services can be provided. In this paper, we present an Adaptive Control Framework (ACF), which is developed for controlled resource sharing and dynamic QoS in real-time multimedia service. We discuss main elements of ACF including 1) Control schemes applicable in the framework, and 2) Control mechanisms used in ACF. It is clearly shown in this paper that, with control schemes and mechanisms incorporated in ACF and supportive algorithms and protocols for ACF applications on the Internet, more flexible service and better overall performance in terms of packet loss, latency, signal-noise ratio and re-synchronization delay, can be offered.

This letter proposes a diffusion model that considers both mobility and multimedia based on the user population process to examine the effects of multimedia in mobile communications. As an application example of this model, the shared bandwidth that can be used by one user in packet communications is evaluated. In this model, the user speed and variation in the number of users in a cell are interrelated with respect to mobility. By examining the shared bandwidth behavior based on multimedia teletraffic characteristics, assuming that the number of simultaneously-communicating users within a cell have self-similarity, we found that shared bandwidth and its variance are not dependent on self-similarity but that variance in the shared bandwidth is dependent on user speed.

Recently, it is required to transfer continuous media over networks without QoS guarantee. In these networks, network congestion will cause transmission delay variance which degrades the quality of continuous media itself. This paper proposes a new protocol using a congestion control with two level rate control in the data transfer level and the coding level. It introduces a TCP-like congestion control mechanism to the rate control of data transfer level, which can detect the QoS change quickly, and adjust the coding rate of continuous media with time interval long enough for its quality. The performance evaluation through software simulation with multiplexing continuous media traffics and TCP traffics shows that the proposed protocol works effectively in the case of network congestion.

This paper proposes a new distributed connection establishment scheme involving several competing network providers in a multimedia telecommunications environment. This connection establishment scheme, which is based on the concept of open competitive bidding, enables mutual selection by users and network providers. By employing this proposed scheme, both network providers and users can pursue their own objectives, according to their own bidding and awarding strategies. In this paper, a simple bidding strategy for network providers is presented, and the effectiveness of this strategy is evaluated by means of computer simulation. It is shown that each network provider can improve its profit by adopting this strategy. In this paper, an example of utility functions for users is presented, and the effectiveness of the mechanism with which users can select a network provider is also evaluated by means of computer simulation. Each user can improve his/her utility by selecting an appropriate network provider based on this utility function.

In this paper, quasi-Gaussian filter, quasi-median filter and locally adaptive filters are introduced. A new adaptive vector filter based on noise estimate is proposed to suppress Gaussian and/or impulse noise. To estimate the type and degree of noise corruption, a noise detector and an edge detector are introduced, and two key parameters are obtained to characterize noise in color image. After globally estimating the type and degree of noise corruption, different locally adaptive filters are properly chosen for image enhancement. All noisy images, used to test filters in experiments, are generated by PaintShopPro and Photoshop software. Experimental results show that the new adaptive filter performs better in suppressing noise and preserving details than the filter in Photoshop software and other filters.

We propose a motion estimation algorithm using less gray level images, which are composed of bits pixels lower than 8 bits pixels. Threshold values for generating low bits pixels from 8 bits pixels are simply determined as median values of pixels in a macro block. The proposed algorithm reduces the computational complexity of motion estimation at less expense of video quality. Moreover, median cut quantization can be applied to multilevel images and combined with a lot of fast algorithms to obtain more effective algorithms.

The current Internet does not offer any quality of service guarantees or support to Internet multimedia applications such as Internet telephony and video-conferencing, due to the best-effort nature of the Internet. Their performance may be adversely affected by network congestion. Also, since these applications commonly employ the UDP transport protocol, which lacks congestion control mechanisms, they may severely overload the network and starve other applications. We present an overview of recent research efforts in developing adaptive delivery models for Internet multimedia applications, which dynamically adjust the transmission rate according to network conditions. We classify the approaches used to develop adaptive delivery models with brief descriptions of representative research work. We then evaluate the approaches based on important design issues and performance criteria, such as the scalability of the control mechanism, responsiveness in detecting and reacting to congestion, and ability to accommodate receiver heterogeniety. Some conclusions are developed regarding the suitability of particular design choices under various conditions.

The intermediate language (IL) modularizes a compiler into target processor independent and dependent parts, called the front-end and the back-end. By adding a new back-end, it is possible to port existing software from one processor to another. This paper presents a new efficient approach to achieve multiple targeting to quite different architectures using different processors as well, by translating from one IL into other existing ILs. This approach makes it possible to reuse existing back-ends. It has been successfully applied to a commercial-scale project for porting public switching system software. Since the target ILs were not predictable in advance, we provided an abstract syntax tree (AST) with attributes accessible by abstract data type (ADT) interface to convey the source language information from our front-end to back-ends. It was translated into several ILs that were developed independently. These translations made the compiler available in a very short time for different cross-target platforms and on several workstations we needed. The structure of this AST and the mapping to these ILs are presented, and retargeting cost is evaluated.

In this paper, we focus on the evaluation of the Erlang capacity for multimedia DS-CDMA systems supporting the multi-class services with different transmission rates, bit error rates, traffic activity factors in the reverse link. The number of concurrent users of the corresponding service group is modeled as a K-dimension Markov chain. Then, the Erlang capacity for the multimedia system can be found based on a K-dimension M/M/m loss system. For an IS-95 type DS-CDMA system, supporting voice/data services, the capacity bounds are depicted in conjunction with the 2-dimensional Markov chain. Furthermore, it is observed that the Erlang capacity with respect to the each service group should be balanced to enhance the total system Erlang capacity. Finally, the channel reservation scheme is considered to increase the total system Erlang capacity.

Although there are many multimedia presentation systems on the market, they have some shortcomings and most of them only can work on one single computer, and few of them can work on Web. Thus, in the thesis we develop a network multimedia presentation system to let users easily design the multimedia presentation without restriction on technology or presentation time and place. Our system includes 3 main components: User Interface that includes temporal specification editor, spatial specification editor and multimedia object interface, Presentation Interface and Knowledge Base. There is a dynamic homepage generator in our system and we propose a displaying algorithm based on the Allen's theory, that there exist 13 temporal relationships between two intervals, for synchronizing the media objects.

This paper describes low-power architecture-methodologies for programmable multimedia processors, which will become major functional units in System-On-a-Chip. After brief review on multimedia processing and low-power considerations, recent programmable chips, including MPUs and DSPs, are investigated in terms of low-power implementation. In order to show the difference of the low-power approaches between programmable processors and ASIC processors, a single-chip MPEG-2 encoder is also included as an example of ASIC design.

This paper describes the implementation and demonstration of local networks for the hyper-media photonic information network (HM-PIN), a candidate for the information service platform offering broadcast and telecommunication services. In addition, the feasibility of the HM-PIN is also demonstrated using prototype local network systems. This local network adopts architecture based on wavelength-division-multiplexing (WDM) and broadcast-and-select (B&S) switching, and supports all HM-PIN services except inter-local-network communication. The major issues of this proposed network are the technologies that support many broadcast channels and reduce channel selection cost. This paper also considers the combination of WDM technology and three alternatives: electrical TDM, subcarrier multiplexing (SCM or electrical FDM), and optical TDM (O-TDM). Three 128 ch (8 wavelengths 16 channels) WDM B&S prototype systems are built to demonstrate the feasibility of the proposed HM-PIN. In WDM/SCM, 30 and 20 Mb/s channels are realized as 16-QAM and 64-QAM, and 155 Mb/s channels are realized by WDM/TDM. Moreover, these three prototypes were connected to form a small HM-PIN and applications such as video distribution and IP datagram cut-through are demonstrated. Furthermore, the delay and throughput of the HM-PIN are evaluated by connecting a local network to a 200-km WDM-ring backbone network. Our discussions and demonstrations confirm the impact and feasibility of the proposed hyper-media photonic information network.

This paper reviews the hyper-media photonic information network (HM-PIN) concept as a candidate of innovative future networks based on photonic technologies. The HM-PIN having a universal network interface integrates a variety of information services: telecommunications, newspapers, magazines, TV broadcasts and the growing collection of information servers. This network fundamentally offers three items: (1) bi-directional real-time channels with 10-Mbit/s-class or higher bit rate, (2) multipoint connections including multicasting/broadcasting, (3) high accessibility to information. These items are derived from the constraints of the conventional telephone networks and the Internet. By applying photonic technologies, the HM-PIN can be implemented as follows: The local network (the service platform) of the HM-PIN can be achieved by using a wavelength-division-multiplexing (WDM) broadcast-and-select (B&S) architecture that offers broadband multipoint connections (one-to-many, many-to-many) based on an inherent full-mesh topology. The WDM B&S local network will be able to support 10,000 to 100,000 channels (each with 10-Mbit/s or more bandwidth) by using optical and electrical multiplexing techniques. The backbone network can be constructed by combining photonic asynchronous transfer mode (ATM) switching systems and WDM transmission systems (including cross-connects). Two deployment scenarios of the HM-PIN (cost-oriented and service-oriented deployment scenarios) are also described for smoothly introducing the HM-PIN even before the cost issue is solved. The HM-PIN based on photonic technologies will be a future network service platform that greatly enhances communication services.

This paper reviews the hyper-media photonic information network (HM-PIN) concept as a candidate of innovative future networks based on photonic technologies. The HM-PIN having a universal network interface integrates a variety of information services: telecommunications, newspapers, magazines, TV broadcasts and the growing collection of information servers. This network fundamentally offers three items: (1) bi-directional real-time channels with 10-Mbit/s-class or higher bit rate, (2) multipoint connections including multicasting/broadcasting, (3) high accessibility to information. These items are derived from the constraints of the conventional telephone networks and the Internet. By applying photonic technologies, the HM-PIN can be implemented as follows: The local network (the service platform) of the HM-PIN can be achieved by using a wavelength-division-multiplexing (WDM) broadcast-and-select (B&S) architecture that offers broadband multipoint connections (one-to-many, many-to-many) based on an inherent full-mesh topology. The WDM B&S local network will be able to support 10,000 to 100,000 channels (each with 10-Mbit/s or more bandwidth) by using optical and electrical multiplexing techniques. The backbone network can be constructed by combining photonic asynchronous transfer mode (ATM) switching systems and WDM transmission systems (including cross-connects). Two deployment scenarios of the HM-PIN (cost-oriented and service-oriented deployment scenarios) are also described for smoothly introducing the HM-PIN even before the cost issue is solved. The HM-PIN based on photonic technologies will be a future network service platform that greatly enhances communication services.

This paper describes the implementation and demonstration of local networks for the hyper-media photonic information network (HM-PIN), a candidate for the information service platform offering broadcast and telecommunication services. In addition, the feasibility of the HM-PIN is also demonstrated using prototype local network systems. This local network adopts architecture based on wavelength-division-multiplexing (WDM) and broadcast-and-select (B&S) switching, and supports all HM-PIN services except inter-local-network communication. The major issues of this proposed network are the technologies that support many broadcast channels and reduce channel selection cost. This paper also considers the combination of WDM technology and three alternatives: electrical TDM, subcarrier multiplexing (SCM or electrical FDM), and optical TDM (O-TDM). Three 128 ch (8 wavelengths 16 channels) WDM B&S prototype systems are built to demonstrate the feasibility of the proposed HM-PIN. In WDM/SCM, 30 and 20 Mb/s channels are realized as 16-QAM and 64-QAM, and 155 Mb/s channels are realized by WDM/TDM. Moreover, these three prototypes were connected to form a small HM-PIN and applications such as video distribution and IP datagram cut-through are demonstrated. Furthermore, the delay and throughput of the HM-PIN are evaluated by connecting a local network to a 200-km WDM-ring backbone network. Our discussions and demonstrations confirm the impact and feasibility of the proposed hyper-media photonic information network.

In this paper, we introduce a processor called Media Core Processor (MCP), which targets a system solution for consumer multimedia products. MCP is a heterogeneous multi-processor system designed to guarantee full frame MPEG decoding, and to reduce power consumption. In our processor architecture, each processing unit is optimized to support various characteristics of media processing. All processing units work in parallel in a macro-pipeline manner, thereby achieving high utilization of the processing units. A performance evaluation shows that audio/video full-frame decoding can be realized on 54 MHz operating frequency without any support from external hardware or a CPU. In addition, the high programmability of the MCP provides flexibility and reduces the time-to-market.

This paper describes a new reconfigurable processor architecture called REMARC (Reconfigurable Multimedia Array Coprocessor). REMARC is a small array processor that is tightly coupled to a main RISC processor. It consists of a global control unit and 64 16-bit processors called nano processors. REMARC is designed to accelerate multimedia applications, such as video compression, decompression, and image processing. These applications typically use 8-bit or 16-bit data therefore, each nano processor has a 16-bit datapath that is much wider than those of other reconfigurable coprocessors. We have developed a programming environment for REMARC and several realistic application programs, DES encryption, MPEG-2 decoding, and MPEG-2 encoding. REMARC can implement various parallel algorithms which appear in these multimedia applications. For instance, REMARC can implement SIMD type instructions similar to multimedia instruction extensions for motion compensation of the MPEG-2 decoding. Furthermore, the highly pipelined algorithms, like systolic algorithms, which appear in motion estimation of the MPEG-2 encoding can also be implemented efficiently. REMARC achieves speedups ranging from a factor of 2.3 to 21.2 over the base processor which is a single issue processor or 2-issue superscalar processor. We also compare its performance with multimedia instruction extensions. Using more processing resources, REMARC can achieve higher performance than multimedia instruction extensions.