Efficient multiplexing of ultra-reliable and low-latency communications (URLLC) and enhanced mobile broadband (eMBB) traffic, as well as ensuring the various reliability requirements of these traffic types in 5G wireless communications, is becoming increasingly important, particularly for vertical services. Interference management techniques, such as coordinated inter-cell scheduling, can enhance reliability in dense cell deployments. However, tight inter-cell coordination necessitates frequent information exchange between cells, which limits implementation. This paper introduces a novel RAN slicing framework based on centralized frequency-domain interference control per slice and link adaptation optimized for URLLC. The proposed framework does not require tight inter-cell coordination but can fulfill the requirements of both the decoding error probability and the delay violation probability of each packet flow. These controls are based on a power-law estimation of the lower tail distribution of a measured data set with a smaller number of discrete samples. As design guidelines, we derived a theoretical minimum radio resource size of a slice to guarantee the delay violation probability requirement. Simulation results demonstrate that the proposed RAN slicing framework can achieve the reliability targets of the URLLC slice while improving the spectrum efficiency of the eMBB slice in a well-balanced manner compared to other evaluated benchmarks.

Direct-current biased optical orthogonal frequency division multiplexing (DCO-OFDM) converts bipolar OFDM signals into unipolar non-negative signals by introducing a high DC bias, which satisfies the requirement that the signal transmitted by intensity modulated/direct detection (IM/DD) must be positive. However, the high DC bias results in low power efficiency of DCO-OFDM. An adaptively biased optical OFDM was proposed, which could be designed with different biases according to the signal amplitude to improve power efficiency in this letter. The adaptive bias does not need to be taken off deliberately at the receiver, and the interference caused by the adaptive bias will only be placed on the reserved subcarriers, which will not affect the effective information. Moreover, the proposed OFDM uses Hartley transform instead of Fourier transform used in conventional optical OFDM, which makes this OFDM have low computational complexity and high spectral efficiency. The simulation results show that the normalized optical bit energy to noise power ratio (Eb(opt)/N0) required by the proposed OFDM at the bit error rate (BER) of 10-3 is, on average, 7.5 dB and 3.4 dB lower than that of DCO-OFDM and superimposed asymmetrically clipped optical OFDM (ACO-OFDM), respectively.

In this paper, we investigated the overfitting characteristics of nonlinear equalizers based on an artificial neural network (ANN) and the Volterra series transfer function (VSTF), which were designed to compensate for optical nonlinear waveform distortion in optical fiber communication systems. Linear waveform distortion caused by, e.g., chromatic dispersion (CD) is commonly compensated by linear equalizers using digital signal processing (DSP) in digital coherent receivers. However, mitigation of nonlinear waveform distortion is considered to be one of the next important issues. An ANN-based nonlinear equalizer is one possible candidate for solving this problem. However, the risk of overfitting of ANNs is one obstacle in using the technology in practical applications. We evaluated and compared the overfitting of ANN- and conventional VSTF-based nonlinear equalizers used to compensate for optical nonlinear distortion. The equalizers were trained on repeated random bit sequences (RRBSs), while varying the length of the bit sequences. When the number of hidden-layer units of the ANN was as large as 100 or 1000, the overfitting characteristics were comparable to those of the VSTF. However, when the number of hidden-layer units was 10, which is usually enough to compensate for optical nonlinear distortion, the overfitting was weaker than that of the VSTF. Furthermore, we confirmed that even commonly used finite impulse response (FIR) filters showed overfitting to the RRBS when the length of the RRBS was equal to or shorter than the length of the tapped delay line of the filters. Conversely, when the RRBS used for the training was sufficiently longer than the tapped delay line, the overfitting could be suppressed, even when using an ANN-based nonlinear equalizer with 10 hidden-layer units.

Information-theoretic security and computational security are fundamental paradigms of security in the theory of cryptography. The two paradigms interact with each other but have shown different progress, which motivates us to explore the intersection between them. In this paper, we focus on Multi-Party Computation (MPC) because the security of MPC is formulated by simulation-based security, which originates from computational security, even if it requires information-theoretic security. We provide several equivalent formalizations of the security of MPC under a semi-honest model from the viewpoints of information theory and statistics. The interpretations of these variants are so natural that they support the other aspects of simulation-based security. Specifically, the variants based on conditional mutual information and sufficient statistics are interesting because security proofs for those variants can be given by information measures and factorization theorem, respectively. To exemplify this, we show several security proofs of BGW (Ben-Or, Goldwasser, Wigderson) protocols, which are basically proved by constructing a simulator.

The influence of the gate voltage or base pair ratio modulation on the λ-DNA FET performance was examined. The result of the gate voltage modulation indicated that the captured electrons in the guanine base of the λ-DNA molecules greatly influenced the Id-Vd characteristics, and that of the base pair ratio modulation indicated that the tendency of the conductivity was partly clarified by considering the activation energy of holes and electrons and the length and numbers of the serial AT or GC sequences over which the holes or electrons jumped. In addition, the influence of the dimensionality of the DNA molecule on the conductivity was discussed theoretically.

Aiming at the problem of “energy hole” caused by random distribution of nodes in large-scale wireless sensor networks (WSNs), this paper proposes an adaptive energy-efficient balanced uneven clustering routing protocol (AEBUC) for WSNs. The competition radius is adaptively adjusted based on the node density and the distance from candidate cluster head (CH) to base station (BS) to achieve scale-controlled adaptive optimal clustering; in candidate CHs, the energy relative density and candidate CH relative density are comprehensively considered to achieve dynamic CH selection. In the inter-cluster communication, based on the principle of energy balance, the relay communication cost function is established and combined with the minimum spanning tree method to realize the optimized inter-cluster multi-hop routing, forming an efficient communication routing tree. The experimental results show that the protocol effectively saves network energy, significantly extends network lifetime, and better solves the “energy hole” problem.

Convolutional Neural Networks (CNNs) and Transformers have achieved remarkable performance in detection and classification tasks. Nevertheless, their feature extraction cannot consider both local and global information, so the detection and classification performance can be further improved. In addition, more and more deep learning networks are designed as more and more complex, and the amount of computation and storage space required is also significantly increased. This paper proposes a combination of CNN and transformer, and designs a local feature enhancement module and global context modeling module to enhance the cascade network. While the local feature enhancement module increases the range of feature extraction, the global context modeling is used to capture the feature maps' global information. To decrease the model complexity, a shared sublayer is designed to realize the sharing of weight parameters between the adjacent convolutional layers or cross convolutional layers, thereby reducing the number of convolutional weight parameters. Moreover, to effectively improve the detection performance of neural networks without increasing network parameters, the optimal transport assignment approach is proposed to resolve the problem of label assignment. The classification loss and regression loss are the summations of the cost between the demander and supplier. The experiment results demonstrate that the proposed Combination of CNN and Transformer with Shared Sublayer (CCTSS) performs better than the state-of-the-art methods in various datasets and applications.

As a potential member of next generation wireless communications, the reconfigurable intelligent surface (RIS) can control the reflected elements to adjust the phase of the transmitted signal with less energy consumption. A novel RIS-assisted index modulation scheme is proposed in this paper, which is named the generalized reflected phase modulation (GRPM). In the GRPM, the transmitted bits are mapped into the reflected phase combination which is conveyed through the reflected elements on the RIS, and detected by the maximum likelihood (ML) detector. The performance analysis of the GRPM with the ML detector is presented, in which the closed form expression of pairwise error probability is derived. The simulation results show the bit error rate (BER) performance of GRPM by comparing with various RIS-assisted index modulation schemes in the conditions of various spectral efficiency and number of antennas.

A city-level digital twin is a critical enabling technology to construct a smart city that helps improve citizens' living conditions and quality of life. Currently, research and development regarding the digital replica city are pursued worldwide. However, many research projects only focus on creating the 3D city model. A mechanism to involve key players, such as data providers, service providers, and application developers, is essential for constructing the digital replica city and producing various city applications. Based on this motivation, the authors of this paper are pursuing a research project, namely Decentralized Digital Twin EcoSystem (D2EcoSys), to create an ecosystem to advance (and self-grow) the digital replica city regarding time and space directions, city services, and values. This paper introduces an overview of the D2EcoSys project: vision, problem statement, and approach. In addition, the paper discusses the recent research results regarding networking technologies and demonstrates an early testbed built in the Kashiwa-no-ha smart city.

Low confusion coefficient values can make side-channel attacks harder for vector Boolean functions in Block cipher. In this paper, we give new results of confusion coefficient for f ⊞ g, f ⊡ g, f ⊕ g and fg for different Boolean functions f and g, respectively. And we deduce a relationship on the sum-of-squares of the confusion coefficient between one n-variable function and two (n - 1)-variable decomposition functions. Finally, we find that the confusion coefficient of vector Boolean functions is affine invariant.

Recently, there has been a surge of interest in Artificial Intelligence (AI) and its applications have been considered in various fields. Mobile networks are becoming an indispensable part of our society, and are considered as one of the promising applications of AI. In the Beyond 5G/6G era, AI will continue to penetrate networks and AI will become an integral part of mobile networks. This paper provides an overview of the collaborations between networks and AI from two categories, “AI for Network” and “Network for AI,” and predicts mobile networks in the B5G/6G era. It is expected that the future mobile network will be an integrated infrastructure, which will not only be a mere application of AI, but also provide as the process infrastructure for AI applications. This integration requires a driving application, and the network operation is one of the leading candidates. Furthermore, the paper describes the latest research and standardization trends in the autonomous networks, which aims to fully automate network operation, as a future network operation concept with AI, and discusses research issues in the future mobile networks.

We have proposed autonomous network diagnosis platform for operation of future large capacity and virtualized network, including 5G and beyond 5G services. As for the one candidate of information collection and analyzing function blocks in the platform, we proposed novel optical sensing techniques that utilized tapped raw signal data acquired from digital coherent optical receivers. The raw signal data is captured before various digital signal processing for demodulation. Therefore, it contains various waveform deformation and/or noise as it experiences through transmission fibers. In this paper, we examined to detect two possible failures in transmission lines including fiber bending and optical filter shift by analyzing the above-mentioned raw signal data with the help of machine learning. For the purpose, we have implemented Docker container applications in WhiteBox Cassini to acquire real-time raw signal data. We generated CNN model for the detections in off-line processing and used them for real-time detections. We have confirmed successful detection of optical fiber bend and/or optical filter shift in real-time with high accuracy. Also, we evaluated their tolerance against ASE noise and invented novel approach to improve detection accuracy. In addition to that, we succeeded to detect them even in the situation of simultaneous occurrence of those failures.

With the gradually increase of the application of new energy in microgrids, Electric Spring (ES), as a new type of distributed compensation power electronic device has been widely studied. The Generalized Electric Spring (G-ES) is an improved topology, and the space limitation problem in the traditional topology is solved. Because of the mode of G-ES use in the power grid, a reasonable solution to the voltage loss of the critical section feeder is needed. In this paper, the voltage balance equation based on the feedforward compensation coefficient is established, and a two cascade control strategy based on the equation is studied. The first stage of the two cascade control strategy is to use communication means to realize the allocation of feedforward compensation coefficients, and the second stage is to use the coefficients to realize feedforward fixed angle control. Simulation analysis shows that the proposed control strategy does not affect the control accuracy of the critical load (CL), and effectively improves the operational range of the G-ES.

Until today, digital image watermarking has not been large-scale used in the industry. The first reason is that the watermarking efficiency is low and the real-time performance cannot be satisfied. The second reason is that the watermarking scheme cannot cope with various attacks. To solve above problems, this paper presents a multi-domain based digital image watermarking scheme, where a fast DFT (Discrete Fourier Transform) based watermarking method is proposed for synchronization correction and an IWT-DCT (Integer Wavelet Transform-Discrete Cosine Transform) based watermarking method is proposed for information embedding. The proposed scheme has high efficiency during embedding and extraction. Compared with five existing schemes, the robustness of our scheme is very strong and our scheme can cope with many common attacks and compound attacks, and thus can be used in wide application scenarios.

In the current heterogeneous wireless communication system, the sharp rise in energy consumption and the emergence of new service types pose great challenges to nowadays radio access network selection algorithms which do not take care of these new trends. So the proposed energy efficiency based multi-service heterogeneous access network selection algorithm-ESRS (Energy Saving Radio access network Selection) is intended to reduce the energy consumption caused by the traffic in the mobile network system composed of Base Stations (BSs) and Access Points (APs). This algorithm models the access network selection problem as a Multiple-Attribute Decision-Making (MADM) problem. To solve this problem, lots of methods are combined, including analytic Hierarchy Process (AHP), weighted grey relational analysis (GRA), entropy theory, simple additive weight (SAW), and utility function theory. There are two main steps in this algorithm. At first, the proposed algorithm gets the result of the user QoS of each network by dealing with the related QoS parameters, in which entropy theory and AHP are used to determine the QoS comprehensive weight, and the SAW is used to get each network's QoS. In addition to user QoS, parameters including user throughput, energy consumption utility and cost utility are also calculated in this step. In the second step, the fuzzy theory is used to define the weight of decision attributes, and weighted grey relational analysis (GRA) is used to calculate the network score, which determines the final choice. Because the fuzzy weight has a preference for the low energy consumption, the energy consumption of the traffic will be saved by choosing the network with the least energy consumption as much as possible. The simulation parts compared the performance of ESRS, ABE and MSNS algorithms. The numerical results show that ESRS algorithm can select the appropriate network based on the service demands and network parameters. Besides, it can effectively reduce the system energy consumption and overall cost while still maintaining a high overall QoS value and a high system throughput, when compared with the other two algorithms.

The complexity and scale of Networks-on-Chip (NoCs) are growing as more processing elements and memory devices are implemented on chips. However, under strict power budgets, it is also critical to lower the power consumption of NoCs for the sake of energy efficiency. In this paper, we therefore present three novel input unit designs for on-chip routers attempting to shrink their power consumption while still conserving the network performance. The key idea behind our designs is to organize buffers in the input units with characteristics of the network traffic in mind; as in our observations, only a small portion of the network traffic are long packets (composed of multiple flits), which means, it is fair to implement hybrid, asymmetric and reconfigurable buffers so that they are mainly targeting at short packets (only having a single flit), hence the smaller power consumption and area overhead. Evaluations show that our hybrid, asymmetric and reconfigurable input unit designs can achieve an average reduction of energy consumption per flit by 45%, 52.3% and 56.2% under 93.6% (for hybrid designs) and 66.3% (for asymmetric and reconfigurable designs) of the original router area, respectively. Meanwhile, we only observe minor degradation in network latency (ranging from 18.4% to 1.5%, on average) with our proposals.

The transfer distance of the wireless power transfer (WPT) system with relay coil is longer, so this technology have a better practical perspective. But the location of the relay coil has a great impact on the transmission efficiency of the WPT system, and it is not easy to analyze. In order to research the influence law of the relay coil location on the transmission efficiency and obtain the optimal location, the paper firstly proposes the concept of relay coil location factor. And based on the location factor, a novel method for studying the influence of the relay coil location on the transmission efficiency is proposed. First, the mathematical model between the transmission efficiency and the location factor is built. Next, considering the transfer distance, coil radius, coil turns and load resistance, a lot of simulations are carried out to analyze the influence of the location factor on the transmission efficiency, respectively. The influence law and the optimal location factor were obtained with different parameters. Finally, a WPT system with relay coil was built for experiments. And the experiment results verify that the theoretical analysis is correct and the proposed method can simplify the analysis progress of the influence of relay coil location on the transmission efficiency. Moreover, the proposed method and the research conclusions can provide guidance for designing the multiple coils structure WPT system.

Social relationships (e.g., couples, opponents) are the foundational part of society. Social relation atmosphere describes the overall interaction environment between social relationships. Discovering social relation atmosphere can help machines better comprehend human behaviors and improve the performance of social intelligent applications. Most existing research mainly focuses on investigating social relationships, while ignoring the social relation atmosphere. Due to the complexity of the expressions in video data and the uncertainty of the social relation atmosphere, it is even difficult to define and evaluate. In this paper, we innovatively analyze the social relation atmosphere in video data. We introduce a Relevant Visual Concept (RVC) from the social relationship recognition task to facilitate social relation atmosphere recognition, because social relationships contain useful information about human interactions and surrounding environments, which are crucial clues for social relation atmosphere recognition. Our approach consists of two main steps: (1) we first generate a group of visual concepts that preserve the inherent social relationship information by utilizing a 3D explanation module; (2) the extracted relevant visual concepts are used to supplement the social relation atmosphere recognition. In addition, we present a new dataset based on the existing Video Social Relation Dataset. Each video is annotated with four kinds of social relation atmosphere attributes and one social relationship. We evaluate the proposed method on our dataset. Experiments with various 3D ConvNets and fusion methods demonstrate that the proposed method can effectively improve recognition accuracy compared to end-to-end ConvNets. The visualization results also indicate that essential information in social relationships can be discovered and used to enhance social relation atmosphere recognition.

With the rapid increase in the amount of data communication in 5G networks, there is a strong demand to reduce the power of the entire network, so the use of highly power-efficient millimeter-wave (mm-wave) networks is being considered. However, while mm-wave communication has high power efficiency, it has strong straightness, so it is difficult to secure stable communication in an environment with blocking. Especially when considering use cases such as autonomous driving, continuous communication is required when transmitting streaming data such as moving images taken by vehicles, it is necessary to compensate the blocking problem. For this reason, the authors examined an optimum radio access technology (RAT) selection scheme which selects mm-wave communication when mm-wave can be used and select wide-area macro-communication when mm-wave may be blocked. In addition, the authors implemented the scheme on a prototype device and conducted field tests and confirmed that mm-wave communication and macro communication were switched at an appropriate timing.

Different types of malicious attacks have been increasing simultaneously and have become a serious issue for cybersecurity. Most attacks leverage domain URLs as an attack communications medium and compromise users into a victim of phishing or spam. We take advantage of machine learning methods to detect the maliciousness of a domain automatically using three features: DNS-based, lexical, and semantic features. The proposed approach exhibits high performance even with a small training dataset. The experimental results demonstrate that the proposed scheme achieves an approximate accuracy of 0.927 when using a random forest classifier.