JunHwan LEE Yoshihisa KISHIYAMA Tomoaki OHTSUKI Masao NAKAGAWA
In a time-invariant wireless channel, the multipath that exceeds the cyclic prefix (CP) or the guard interval (GI) causes orthogonal frequency division multiplexing (OFDM) systems to hardly achieve high data rate transmission due to the inter-symbol interference (ISI) and the inter-carrier interference (ICI). In this paper the new canceller scheme, named as Double Window Cancellation and Combining (DWCC) is proposed. It includes the entire symbol interval, delayed by multipath as a signal processing window and intends to improve the performance by combining the double windows that can be formed by the pre- and post-ISI cancellation and reconstruction to the received OFDM symbol interfered by the multipath exceeding the guard interval. The proposed scheme has two algorithm structures of the DWCC-I and -II which are distinguished by the operational sequence (Symbol-wise or Group-wise) to the OFDM symbols of the received packet and by the selection of the processing window in the iterative decision feedback processing. Since the performance of the canceller is dependant on the equalization, particularly on the initial equalization, the proposed schemes operate with the time and frequency domain equalizer in the initial and the iterative symbol detection, respectively. For the verification of the proposed schemes, each scheme is evaluated in the turbo coded OFDM for low (QPSK) and high level modulation systems (16QAM, 64QAM), and compared with the conventional canceller with respect to the performance and computational complexity. As a result, the proposed schemes do not have an error floor even for 64QAM in a severe frequency selective channel.
Takayuki KATO Keiichi YAMAGUCHI Yasuhiko KURIYAMA Hiroshi YOSHIDA
This paper presents a miniaturized dual-mode Doherty PA module applicable for an HPSK signal and an OFDM 64-QAM signal. Dual-mode operation with identical hardware is realized by introducing a bias switching technique, which changes bias conditions of amplifiers according to transmission signals, and employing dual-mode matching circuits, which are designed based on the results of load-pull measurements using an HPSK signal and an OFDM 64-QAM signal. The Doherty PA module consists of a Doherty stage and a gain stage. Two GaAs-HBTs for a Doherty stage and one GaAs-HBT for a gain stage are integrated onto a 1 mm-square single GaAs-MMIC. In the HPSK mode, maximum output power of 26.7 dBm, power added efficiency (PAE) of 41%, and power gain of 27 dB are obtained in the condition that adjacent channel leakage power ratio (ACLR) is under -38 dBc. In the OFDM 64-QAM mode, maximum output power of 21.0 dBm, PAE of 27%, and power gain of 28 dB are obtained under EVM < 3.0%. This is the first multi-mode Doherty PA module suitable for multi peak to average power ratio (PAPR) signals.
In this paper, we propose a novel open-loop Automatic Frequency Control (AFC) circuit suitable for 64QAM point-to-multipoint (P-MP) burst communications. The proposed AFC contains two frequency offset detectors. One estimates the phase rotation over long intervals to obtain accurate estimates at the cost of phase ambiguity. The other estimates the phase rotation over short intervals and its output is used to resolve the ambiguity in the following phase ambiguity compensator. Thus, the proposed AFC circuit calculates the phase rotation over sufficiently long periods to yield accurately estimate the carrier frequency offset while suppressing the phase-unwrapping problem. The proposed AFC approaches the Cramer-Rao bound (CRB) and so achieves very small residual frequency offset. The proposed AFC circuit can be implemented with much smaller circuit scale than the conventional devices. Computer simulations and experiments confirm that its residual frequency error is less than of 10-5 for the frame format considered; this performance is sufficient for the 64QAM -40 Mbaud system targeted.
Dah-Chung CHANG Wei-Tsen LIN Yung-Fang CHEN
A new Kalman carrier synchronization algorithm is developed for high-order QAM transmission to reduce complexity compared to the conventional Kalman approach. The state model in the proposed algorithm employs only phase, instead of both phase and frequency, as in the conventional method. A reduced-observation model is also introduced to eliminate matrix operations in the Kalman recursions. Simulations results show that the one-state Kalman algorithm has better performance and lower complexity than the two-state Kalman algorithm. The cable modem downstream system is applied to demonstrate the effectiveness of the proposed algorithm.
Bayarpurev MONGOL Takaya YAMAZATO Hiraku OKADA Masaaki KATAYAMA
Pulse-shaping OFDM is well-known that it performs well in a mobile environment compared with conventional OFDM. However, in a highly mobile environment intersymbol and intercarrier interferences (ISI/ICIs) increase and can no longer be neglected. These ISI/ICIs deteriorate the performance of the systems. Proper channel equalization is needed for further improvement of the systems. In this paper, a more general case, namely Biorthogonal Frequency Division System based on Offset QAM (BFDM/OQAM) is considered. We propose a multi-input multi-output (MIMO) transversal filter to equalize the time-frequency dispersive channel. Tap weights are calculated using the zero-forcing (ZF) algorithm. We also propose maximum-likelihood channel estimator and its low-complexity version. The proposed system can significantly improve the performance of BFDM/OQAM systems in the highly mobile environment.
Hiroshi YOSHIOKA Yushi SHIRATO Kazuji WATANABE
We propose a novel simplified Viterbi equalizer for high symbol rate FWA (Fixed Wireless Access) systems carrying 64QAM signals. Reduced complexity and improved performance are achieved adopting two approaches. The first one is reducing the number of survival paths, taking advantage of the large D/U common in LOS (line of sight) communications. The second one is using a multi-stage process to generate desired signal replicas based on their likelihoods. Computer simulations confirm that the proposed replica generation method offers a performance improvement of about 1 dB and the proposed Viterbi equalizer offers reduced complexity with no performance penalty compared to full Viterbi equalizer.
The paper presents an adaptive algorithm named adaptive threshold nonlinear algorithm for use in adaptive filters in the complex-number domain (c-ATNA) in applications to digital QAM systems. Although the c-ATNA is very simple to implement, it makes adaptive filters highly robust against impulse noise and at the same time it ensures filter convergence as fast as that of the well-known LMS algorithm. Analysis is developed to derive a set of difference equations for calculating transient behavior as well as steady-state performance. Experiment with simulations and theoretical calculations for some examples of filter convergence in the presence of Contaminated Gaussian Noise demonstrates that the c-ATNA is effective in combating impulse noise. Good agreement between simulated and theoretical convergence proves the validity of the analysis.
In this paper, we present a new all-digital carrier recovery loop for high-order quadrature amplitude modulation (QAM) signal constellations. The proposed approach is a blind phase-frequency detector structure that consists of a phase detector, a phase offset estimator, a frequency offset estimator, and a digital control oscillator. Compared to previous related approaches, the proposed algorithm provides a wider acquisition range and a more accurate estimation of frequency and phase offsets. These features are demonstrated by simulation results of the DOCSIS (Data-Over-Cable Service Interface Specifications) cable modem system.
Jung Seok LIM Kwangmin HYUN Dongweon YOON Sang Kyu PARK
We derive and analyze a bit error rate (BER) expression of a Gray coded rectangular QAM (R-QAM) signal with maximal ratio combining (MRC) diversity reception over Nakagami-n (Rician) fading channels. The derived result is provided in terms of the Whittaker function and the confluent hypergeometric function. Because the derived expression is general, it can readily allow numerical evaluation for various cases of practical interest such as line-of-sight (LOS) or satellite communication channel analysis.
Hristo KOSTADINOV Hiroyoshi MORITA Nikolai MANEV
In this paper we present the exact expressions for the bit error probability over a Gaussian noise channel of coded QAM using single error correcting integer codes. It is shown that the proposed integer codes have a better performance with respect to the lower on the bit error probability for trellis coded modulation.
In this paper, we propose a transmitter structure in digital QAM systems where pre-compensator compensates for nonlinearity with "memory effects" at the output amplifier. The nonlinearity is modeled as a linear time-invariant filter cascaded by memoryless nonlinearity (Wiener model), whereas the pre-compensator comprises an FIR-type adaptive filter that follows a memoryless predistorter based on a series expansion with orthogonal polynomials for digital QAM data. The predistorter and the adaptive filter of the pre-compensator are stochastically and directly adapted using the error signal. The theoretically optimum parameters of the predistorter are approximately solved whence the steady-state mean square compensation error is calculated. Simulations show that the proposed pre-compensator can be adapted to achieve a sufficiently small compensation error, restoring the original QAM constellation through linearization and equalization of the nonlinearity with memory effects.
Hyoungsik NAM Tae Hun KIM Yongchul SONG Jae Hoon SHIM Beomsup KIM Yong Hoon LEE
This paper describes the design of a programmable QAM transceiver for VDSL applications. A 12-b DAC with 64-dB spurious-free dynamic range (SFDR) at 75-MS/s and an 11-b ADC with 72.3-dB SFDR at 70-MS/s are integrated in this complete physical layer IC. A digital IIR notch filter is included in order to not interrupt existing amateur radio bands. The proposed dual loop AGC adjusts the gain of a variable gain amplifier (VGA) to obtain maximum SNR while avoiding saturation. Using several low power techniques, the total power consumption is reduced to 300-mW at 1.8-V core and 3.3-V I/O supplies. The transceiver is fabricated in a 0.18-µm CMOS process and the chip size is 5-mm 5-mm. This VDSL transceiver supports 13-Mbps data rate over a 9000-ft channel with a BER < 10-7.
Kwangmin HYUN Dongweon YOON Sang Kyu PARK
General closed-form expressions are derived and analyzed for the exact bit error rate (BER) performance of the arbitrary rectangular Gray coded QAM signal in conjunction with maximal-ratio combining (MRC) diversity on frequency non-selective slow m-distributed Nakagami fading channel. The analyses consider four channel models, independent and identical, independent and nonidentical, identical but correlated, and arbitrary correlated fading. Numerical results demonstrate error performance improvement with the use of MRC diversity reception. The new expressions presented here are suitable for evaluating various cases of practical interest on wireless communication channels.
Hyeongseok YU Byung Wook KIM Jun-Dong CHO
In this paper, an area efficient VLSI architecture of decision feedback equalizer is derived accommodating 64/256 QAM modulators. This architecture is implemented efficiently in VLSI structure using EDA tools due to its regular structure. The method is to employ a time-multiplexed design scheme, so-called Folding, which executes multiple operation on a single functional unit. In addition, we define a new folding set by grouping the adjacent filter taps with data transfer having the same processing sequence between blocks and perform the internal data-bit optimization. By doing so, the computational complexity is reduced by performance optimization and also silicon area is reduced by using a shared operator. Moreover, through the performance and convergence time comparison of the various LMS (e.g. LMS, data signed LMS, error signed LMS, signed-signed LMS) ) coefficient updating algorithms, we identify an optimum LMS algorithm scheme suitable for the low complexity, high performance and high order (64 and 256) QAM applications for the presented Fractionally Spaced Decision Feedback Equalizer. We simulated the proposed design scheme using SYNOPSYSTM and SPWTM.
Jong-Ho LEE Jae-Choong HAN Seong-Cheol KIM
In this letter, iterative sequence estimation technique based on expectation-maximization (EM) algorithm is considered for quadrature amplitude modulation (QAM)-orthogonal frequency division multiplexing (OFDM) signals. For QAM-OFDM signaling, the optimal EM algorithm requires high computational complexity due to the inversion of complex matrix executed at each iteration. To avoid this problem, we propose a sub-optimal iterative sequence estimation algorithm with some approximations, which results in reduced computational complexity for QAM-OFDM signals. Moreover, we use two different approaches to obtain initial estimate for beginning iteration of proposed algorithm. One is for less time-dispersive but fast fading channel and the other is for highly time-dispersive but relatively slow fading channel. The bit error rate (BER) performances of the proposed algorithm are evaluated using computer simulations. The results show that the proposed algorithm performs nearly as well as the optimal EM algorithm.
In this paper, a quasi-synchronous code-division multiple-access (QS-CDMA) is investigated for application in the reverse link of a microcellular or indoor mobile communication environment. In a QS-CDMA system, the relative time delay between the signals of different users is normally restricted within a few chips. Generalized orthogonal (GO) codes added with guard chips are employed as the spreading sequences in this paper and the strict timing error restrictions for BPSK and M-QAM modulation schemes are derived based on the correlation properties of GO code set which determines the multiple access interference (MAI). The results reveal that the system employing GO code set with bigger GO zone can tolerate more serious timing error, and higher order modulation schemes require stricter synchronization. Based on the system model presented, the BER performance for BPSK and M-QAM is evaluated by Gaussian Approximation (GA) and Monte Carlo simulation. The system capacity in terms of acquirable total bit rates are also evaluated, revealing that if system synchronization error is limited within the GO zone, M-QAM scheme can be utilized to improve the system capacity.
We present the channel capacity, specifically the mutual information, of an additive white Gaussian noise (AWGN) channel in the presence of phase noise, and investigate the effect of phase noise impairment on powerful error-correcting codes (ECCs) that normally operate in low signal-to-noise ratio (SNR) regions. This channel-induced impairment is common in digital coherent transmission systems and is caused by imperfect carrier tracking of the phase error detector for coherent demodulation. It is shown through semi-analytical derivation that decreasing the information rate from its ideal capacity to an information rate lower than its inherent capacity significantly mitigates the impairment caused by phase noise, and that operating systems in the low SNR region also lessen the phase noise impairment by transforming typical phase noise behavior into Gaussian-like behavior. We also demonstrate by computer simulation using turbo-trellis coded modulation (TTCM) with high-order quadrature amplitude modulation (QAM) signals that the use of capacity-approaching codes (CACs) makes transmission systems invulnerable to phase noise. To verify the effect of CACs on phase noise, simulation results of TTCM are also compared to that of trellis-coded modulation (TCM), which is used as an example of a conventional ECC operating at a relatively high SNR.
We experimentally demonstrated a remote antenna system based on a millimeter-wave (MMW) over fiber scheme for 622-Mbps broadband fixed wireless access systems. In this system, the format of the RF signal is based on a four-carrier signal in which each carrier is modulated by using 64-QAM, to reduce the complexity of the RF system in comparison with the single-carrier QAM system using many more signal-points than 64. The remote antenna system based on the IF-over-fiber scheme was also experimentally demonstrated, as well as the MMW over fiber scheme for comparison. From the experimental results, we found that the remote antenna system based on the MMW over fiber scheme is effective not only from the viewpoints of miniaturization of the remote antenna station and ability to provide a stable millimeter-wave frequency, but also from the viewpoint of link performances such as allowable dynamic range and power penalty, even though the scheme's E/O and O/E devices have a higher cost.
Minjoong RIM Jaemin AHN Yeon-soo KIM
When decision-directed channel estimation is used for QAM-OFDM systems, the optimal filter shape depends on the amplitudes of the modulated symbols as well as the channel characteristics. In this letter we propose a simple channel estimation method for multi-level-amplitude-modulated systems, which can effectively suppress the estimation variances with a small filter. Using the proposed method the implementation cost can be reduced and possibly better results might be obtained by avoiding the estimation bias due to large-sized filtering.
This paper derives a set of orthogonal polynomials for a complex random variable that is uniformly distributed in two dimensions (2D). The polynomials are used in a series expansion to approximate memoryless nonlinearities in digital QAM systems. We also study stochastic identification of nonlinearities using the orthogonal polynomials through analysis and simulations.