We present a physics-based circuit simulator employing the Monte Carlo (MC) particle technique, which serves as a bridge between the small-device physics and the circuit designs. Two different geometries of GaAs-MESFET's are modeled and analyzed by the simulator. The Y-parameters of the devices are extracted from the transient currents, and then translated into the S-parameters. The cut-off frequency (fT) is estimated from the Y-parameters. The minimum noise figure (Fmin) is also estimated by evaluating the fluctuation in the stationary current. The device, having the n+-region placed just at the drain side of the gate, exhibits the better performances in both fT and Fmin. The analysis on the equivalent circuit (EC) elements reveals that its better performances are mainly due to the reduced gate-source capacitance (Cgs) and the increased transconductance (gm0), which result from the shortened effective gate length (Lg) caused by the termination of the depletion region at the gate edge. The termination of the depletion region, however, causes the increase of the electric field, which results in the higher heat generation rate near the gate edge. It is proven that the physics-based circuit simulator developed here is fully effective to see the inside of the small-device and to model it for the millimeter-wave circuit design.

An 18 GHz-band Microwave Monolithic Integrated Circuit (MMIC) diode linearizer using a parallel capacitor with a bias feed resistance is presented. The newly employed parallel capacitor is able to control gain and phase deviations of the linearizer. This implies that the gain deviation of the linearizer can be controlled without changing the phase deviation. The presented linearizer can compensate the distortion of an amplifier sufficiently. The operation principle of the linearizer with the parallel capacitor is investigated. It is clarified that the gain deviation can be adjusted without changing the phase deviation by using the parallel capacitor. Two variable gain buffer amplifiers and the core part of the linearizer which consists of a diode, a bias feed resistor, and a capacitor are fabricated on the MMIC chip. The amplifiers cancel the frequency dependence of the core part of the linearizer to improve bandwidth of the MMIC. Further, the amplifiers contribute to earn low reflection and compensate insertion loss of the linearizer. The MMIC chip is size of 2.5 mm 1 mm. The linearizer has demonstrated improvement of 3rd Inter-Modulation Distortion (IMD3) of 12 dB at 18 GHz and improvement of more than 6 dB between 17.8 GHz and 18.6 GHz.

A millimeter-wave radio access system has a number of features that makes it appealing as one approach to broadband communications. However, for a millimeter-wave system to come into wide use, it must be miniaturized and the associated costs reduced. We have succeeded in realizing a compact 156 Mbps radio transceiver with a 38 GHz band optimizing RF architecture. We also adopted newly developed three-dimensional laminated MCMs using low cost plastic composite materials. It was confirmed in the initial experiments that this millimeter-wave wireless LAN equipment can cover a sufficient service area for broadband telecommunications in an indoor environment.

We have developed a 2 GHz band superconducting 8-pole tunable quasi-elliptic function filter on sapphire substrate. The tunable filter has a sharp skirt characteristic by transmission zeros. And the tunable filter uses a low-cost substrate of sapphire. An adjustment of center frequency for the filter is realized by a tunable technique with a piezoelectric bending actuator. The tunable filter realized center frequency shift of 7.62 MHz with conditions of bandwidth change of 0.5% and ripple change of 0.25 dB. Center frequency of the 8-pole quasi-elliptic function filter agreed with the designed value. Given these features, a superconducting filter with a sharp skirt characteristic for next-generation mobile RF applications is expected to be realized by applying these filters.

Whispering-Gallery mode resonator method has been presented for complex permittivity evaluation of low loss dielectric materials in millimeter wave region. As a problem, it has been found that the evaluation error slightly dependens on the frequency for a sample. It comes from approximated analysis which is used in the procedure. In this paper, a mode-matching method is applied to this evaluation technique to have improvement of the measrued results. It is confirmed experimentally that reliability of the presented method is improved for the millimeter wave permittivity measurement.

So far, a lot of analyses have been performed on the edge-guide mode isolator with one short edge. However, the detailed characteristics such as the influence of shape of a metal strip and the thickness of a ferrite substrate have not been revealed. This paper clarifies the influence of the structure on the frequency response both experimentally and numerically. The numerical analysis is performed by the FDTD method. The numerical results indicate that the frequency response does not depend on the thickness of ferrite substrate but does on the shape of the metal strip. Furthermore, based on the numerical results, the experiment is carried out on the prototype isolator. All the results provide a theory of the optimum design on the isolator.

This paper newly proposes a hollow ferrite waveguide which consists of a microstrip line loaded on two ferrite slabs with adjacent air gap. Dispersion relation of magnetostatic surface wave in the waveguide is derived by the two dimensional analysis, and reciprocal behavior for parallel bias magnetic field and nonreciprocal behavior for antiparallel bias magnetic field are shown. Propagation characteristic of magnetostatic surface wave in the hollow ferrite waveguide are experimentally demonstrated under both parallel and antiparallel bias magnetic field directions. Strong nonreciprocal behavior in the hollow guide was found for case of antiparallel bias field configuration. These experimental results are mostly in agreement with the dispersion diagram. A nonreciprocal four port junction is demonstrated as an application of the hollow ferrite waveguide.

A compact high-temperature superconducting (HTS) bandpass filter (BPF) using coplanar waveguide (CPW) meander-line parallel-circuited resonators is proposed for microwave receiver applications. The design theory is presented based on a conventional filter theory with J-inverters. Also, analytical and numerical studies of the meander-line resonator are carried out in terms of equivalent circuit values, the resonant frequency, and the unloaded Q. Two- and four-stage 0.05 dB ripple Chebyshev BPFs at 2 GHz with relative bandwidth 60 MHz are fabricated with the metalorganic deposition (MOD)-derived YBCO films on LaAlO3 substrates and their performance are demonstrated. The measured frequency characteristics and the unloaded quality factors agree well with the theoretical and numerical results and the validity of the design theory is confirmed.

We present a design and implementation of a QoS control mechanism in an Adaptive Multimedia Communication System (AMCS) using multiagent-based computing technology. In this paper, we first define functional requirements for AMCS. Subsequently we describe the design and implementation of AMCS with a knowledge-based multiagent framework to fulfill the functional requirements. Moreover we evaluate the adaptability of the prototype systems of AMCS with the operational situations observed in its experiments. From the result of the experiments, we conclude that the multiagent-based design and implementation is reasonable for construction of AMCS.

An element consist of a slot and a post is designed for canceling the reflection in a rectangular waveguide by the method of moments. For reducing the computation time in practical design of the element with a wide range of coupling strength for an array, only the axial uniform currents on the post surface are considered. This approximation is valid when the post for reflection-canceling is far enough from the slot. The post location is determined by this simple analysis for both transverse and longitudinal slots with typical coupling strength. Measured results using 4 GHz-band standard waveguides reveal that the assumption of uniform line currents on the post surface is acceptable. The design is further extended to demonstrate its applicability to a practical array design by considering a wide range of coupling strength.

This paper studies the local Poisson property of aggregated IP traffic. First, it describes the scenario where IP traffic presents a Poisson-like characteristic within some limited range of time scales when packets from independent traffic streams are aggregated. Each of the independent traffic streams corresponds to a series of correlated IP packets such as those of a transport connection. Since the Poisson-like characteristic is observed only within some limited range of time scales, we call this characteristic the local Poisson property. The limited range of time scales of the local Poisson property can be estimated from a network configuration and characteristics of transport connections. Second, based on these observations, we seek the possibility to apply an ordinary Poisson process to evaluation of the packet loss probability in IP networks. The analytical investigation, where IP traffic is modeled by a superposition of independent branching Poisson processes that presents the local Poisson property, suggests that the packet loss probability can be estimated by a finite-buffer queue with a Poisson process when the buffer size is within a certain range. The investigation is verified by simulations. These findings expand the applicability of conventional Poisson-based approaches to IP network design issues.

This paper proposes a technique for indexing, clustering and retrieving images based on their edge features. In this technique, images are decomposed into several frequency bands using the Haar wavelet transform. From the one-level decomposition sub-bands an edge image is formed. Next, the higher order auto-correlation function is applied on the edge image to extract the edge features. These higher order autocorrelation features are normalized to generate a compact feature vector, which is invariant to shift, image size. We used direction cosine as measure of distance not to be influenced by difference of each image's luminance. Then, these feature vectors are clustered by a self-organizing map (SOM) based on their edge feature similarity. The performed experiments show higher precision and recall of this technique than traditional ways in clustering and retrieving images in a large image database environment.

An ultra-low power 4.3 GHz Synchronous Oscillator (SO) is presented, integrated in a 0.25 µm BiCMOS SiGe technology, to act as the RF loop of an UMTS double-loop synthesizer. This SO is tunable in order to counteract technology discrepancies. Hence, the synchronization range is smaller, reducing unwanted synchronization and improving the frequency generation accuracy. This 1.8 V SO provides a -115 dBc/Hz phase noise at 100 kHz offset, consuming only 3.6 mW.

Adaptive arrays have been recognized as an attractive mean for overcoming multipath fading and interference rejection in the field of mobile communications. In, an adaptive array applicable to single-user spread spectrum (SS) systems has been proposed. In this system, any a priori information concerning incoming signal, even the spreading code and synchronization, is not necessary while it achieves equalizing, beamforming and despreading of a received signal, simultaneously. In this paper, we propose a multistage blind adaptive array antenna based on the above-mentioned adaptive algorithm in order to realize blind signal processing that is applicable to multi-user SS systems. Behavior and performance of the proposed multistage system are examined through computer simulations.

The design, fabrication, and characterization of monolithic analog phase shifters based on barium-strontium-titanate (BST) coated sapphire substrates with continuously variable 180and 360phase-shift ranges are presented. The phase shifter using a single series resonated termination can provide 180phase shift with the chip area of 4 mm 4 mm. A double series resonated termination in a parallel connection can reach over 370phase shift with better than 6.8 dB-loss at 2.4 GHz. Also, an all-pass network phase shifter composed of only lumped LC elements was described here. This phase shifter demonstrated 160phase shift with an insertion loss of 3.1 dB 1 dB and return loss of better than 10 dB at 2.4 GHz. The total size of the phase shifter is only 2.4 mm 2.6 mm, which is the smallest reported BST phase shifter operating at S-band, to the best of the authors' knowledge.

In this paper a digital frequency domain RFI (Radio Frequency Interference) cancellation scheme for DMT (Discrete Multitone) based VDSL (Very high speed Digital Subscriber Line) systems is presented. The proposed algorithm has been optimized and characterized in terms of complexity and performance. Optimizations were also performed from an implementation point of view by deducing key dependencies among our RFI model coefficients that let us drastically reduce the size of the memories involved. System simulations showed the effectiveness of the canceller: in terms of VDSL performance parameters such as bit rate, the optimized cancellation scheme recovers almost totally the performance degradation due to RFI.

We report in this paper, the performance of AlGaN/GaN HFETs in the context of high power, low noise and high temperature operations, along with a comparison of their characteristics with other conventional technologies. Finally, a single stage modulator driver for long haul optical communications is presented as an example of application of the GaN-based devices high power handling capabilities.

Future electric lights will be comprised of white LEDs (Light Emitting Diodes). White LEDs with a high power output are expected to serve in the next generation of lamps. In this paper, an indoor visible data transmission system utilizing white LED lights is proposed. In the proposed system, these devices are used not only for illuminating rooms but also for an optical wireless communication system. This system is suitable for private networks such as consumer communication networks. However, it remains necessary to investigate the properties of white LEDs when they are used as optical transmitters. Based on numerical analyses and computer simulations, it was confirmed that the proposed system could be used for indoor optical transmission.

This paper proposes a novel extraction method of line parameters for multi-coupled lines on high-speed and high-density PCBs, where it uses TDR measurement in time domain and S-parameter measurement in frequency domain. The accuracy of the proposed method have been verified experimentally by comparing the crosstalk noise in the time domain, where (1) the proposed method extracts RLGC matrices by measuring the test pattern, (2) the crosstalk noise is obtained through SPICE simulation using the extracted RLGC matrices, and (3) the SPICE-simulated crosstalk noise is compared with the measured crosstalk noise. From the crosstalk noise comparison, the proposed method is proven to be very accurate. For N-coupled lines, the proposed method doesn't require expensive 2N-port probe for N-coupled lines but only two-port probe, which provides a simple, accurate, and economic extraction method of line parameters for multi-coupled line on the PCB. In the early stage of PCB design, the proposed method is very useful, because it extracts accurate interconnection parameters of each test board and enables to compensate various side effects due to the variation of PCB fabrication process. Also, the proposed method is necessary to analyze the signal integrity of future high-density and high-speed digital system on PCBs.

An attenuation measurement system, which employs a traceable inductive voltage divider (IVD) at 1 kHz as a reference standard and dual channel intermediate frequency (IF) substitution method, is developed as an attenuation standard in the frequency range of 5 GHz to 12 GHz. The basic properties of the system are experimentally investigated and the expanded standard uncertainty of the system is estimated to be 0.0018 dB for 20 dB and 0.026 dB for 80 dB attenuation.