Recent advances of Web information systems such as e-commerce and e-learning have created very large but hidden demands on conceptual multiresolution analysis for more generalized information analysis, cognition and modeling. To meet the demands in a general way, its modeling is formulated based on modern algebraic topology. To be specific, the modeling formulation is worked out in an incrementally modular abstraction hierarchy with emphasis on the two levels of the hierarchy appropriate for conceptual modeling: the adjunction space level and the cellular structured space level. Examples are shown to demonstrate the usefulness of the presented model as well as an implementation of a flower structure case.

We developed compact high-power photonic millimeter-wave emitter (PME) modules for 60-GHz fiber radio links. The PME chip is a monolithic integration of a uni-traveling-carrier photodiode (UTC-PD) and an antenna. One module was fabricated by attaching the chip and a plastic housing to a metal substrate, and the equivalent-isotropic radiated power (EIRP) of over 8 dBm was obtained with weak directivity of the radiated pattern. This module is suitable for point-to-multi-point communication. It is very compact, 29 24 6 mm. A module whose antenna gain was increased by attaching a dielectric lens to it was also fabricated, and the estimated EIRP of 18 dBm was obtained. This type of module is suitable for point-to-point communication and it too is compact, 29 24 17.5 mm. We achieved high-speed error-free data transmission of 1.25- and 2.5-Gbit/s phase-shift keyed (PSK) signal. The maximum distances of free-space propagation were estimated to be 18.2 and 8.9 m at bit rates of 1.25 and 2.5 Gbit/s, respectively.

A new technique for optical generation of high-purity millimeter-wave (mm-wave) signals--namely, by synthesizing the outputs from cascadingly phase-locked multiple semiconductor lasers--was developed. Firstly, a high-spectral-purity mm-wave signal was optically generated by heterodyning the outputs from two phase-locked external-cavity semiconductor lasers. The beat signal was detected by a p-i-n photodiode whose output was directly coupled to a coax-waveguide converter followed by a W-band harmonic mixer. By constructing an optical phase-locked loop (OPLL), a high-spectral-purity mm-wave signal with an electrical power of 2.3 µW was successfully generated at 110 GHz with an rms phase fluctuation of 57 mrad. Secondly, the frequency of the mm-wave signal was extended by use of three cascadingly phase-locked semiconductor lasers. This technique uses a semiconductor optical amplifier (SOA) to generate four-wave-mixing (FWM) signals as well as to amplify the input signals. When the three lasers were appropriately tuned, two pairs of FWM signals were nearly degenerated. By phase-locking the offset frequency in one of the nearly degenerated pairs, the frequency separations among the three lasers were kept at a ratio of 1:2. Thus, we successfully generated high-purity millimeter-wave optical-beat signals at frequencies at 330.566 GHz with an rms phase fluctuation of 0.38 rad. A detailed analysis of the phase fluctuations was carried out on the basis of measured power spectral densities. The possibility of extending the mm-wave frequency up to 1 THz by using four cascadingly phase-locked lasers was also discussed.

The forbidden state problem is to synthesize a control policy for preventing a Petri net from reaching any state in its forbidden set. In this paper, we address a liveness preserving version of the forbidden state problem for lossy Petri nets. During the process of keeping Petri nets out of the set of their forbidden states, a control policy does not disable a live marking. We present a method to solve the above problem based on fixed point computations. We show that for lossy Petri nets, the problem is decidable. From a practical viewpoint, the problem associated with our fixed point approach is 'state explosion. ' In order to overcome this problem, we propose a symbolic approach, which uses Boolean functions for implicitly representing the set of states. We use Boolean functions for representing reachable markings. Thus OBDDs, compact representations of Boolean functions, can reduce the time and space involved in solving the forbidden state problem described in this paper.

Recently, layer-4 (L4) switches have been widely used as load balancing front-end routers for Web server clusters. The typical L4 switch attempts to balance load among the servers by estimating load using the load metrics measured in the front-end and/or the servers. However, insufficient load metrics, measurement overhead, and feedback delay often cause misestimate of server load. This may incur significant dynamic load imbalance among the servers particularly when the variation of requested content is high. In this paper, we propose a new content sniffer based load distribution strategy. By sniffing the requests being forwarded to the servers and by extracting load metrics from them, the L4 switch with our strategy more timely and accurately estimates server load without the help of back-end servers. Thus it can properly react to dynamic load imbalance among the servers under various workloads. Our experimental results demonstrate substantial performance improvements over other load balancing strategies used in the typical L4 switch.

An important area in visual communications is the restoration of image sequences degraded by channel and noise. Since a nonlinearity is commonly involved in image transmitting procedure, an adaptive nonlinear equalizer is required. In this paper we address this problem by proposing a 3D adaptive nonlinear filter, namely the 3D adaptive Volterra filter with an LMS type of adaptation algorithm. This adaptive filter is used for equalizing an unknown 2-D channel with some point-wise nonlinearity and restoring image sequences degraded by this channel. Prior to filtering, motion is estimated from the sequence and compensated for. For this purpose, a robust region-recursive Higher Order Statistics (HOS) based motion estimation method is employed. The overall combination is able to adequately remove undesired effects of communication channel and noise. The performance of this algorithm is examined using real image sequences demonstrated by experimental results.

The equidistortion principle[1] has recently been proposed as a basic principle for design of an optimal vector quantization (VQ) codebook. The equidistortion principle adjusts all codebook vectors such that they have the same contribution to quantization error. This paper introduces a novel VQ codebook design algorithm based on the equidistortion principle. The proposed algorithm is a variant of the law-of-the-jungle algorithm (LOJ), which duplicates useful codebook vectors and removes useless vectors. Due to the LOJ mechanism, the proposed algorithm can establish the equidistortion condition without wasting learning steps. This is significantly effective in preventing performance degradation caused when initial states of codebook vectors are improper to find an optimal codebook. Therefore, even in the case of improper initialization, the proposed algorithm can achieve minimization of quantization error based on the equidistortion principle. Performance of the proposed algorithm is discussed through experimental results.

This letter introduces a chaotic circuit consisting of one linear 2-port VCCS, one hysteresis 2-port VCCS, and two capacitors. The circuit has double screw attractors, quad screw attractors and co-existence states of them. Since the system is piecewise linear, attractors existence condition can be described using exact piecewise solutions. Using a simple test circuit, typical phenomena are verified in the laboratory.

A minor component analysis approach based on the generalized sidelobe canceler is presented to realize the blind suppression of multiple-access interference in multicarrier code division multiple access systems. With a rough user-code and timing estimations, this proposed method of less computation performs the same as minimum mean square error detectors and outperforms existing blind detectors. Simulation results illustrate the effectiveness of the blind multiuser detection.

Various optical fiber connectors have been developed during the 20 years since optical fiber communications systems were first put into practical use. As the domain of optical fiber communication systems expanded from trunk lines to subscriber lines and customer premises the main focus changed from performance improvement to miniaturization and cost reduction. This paper describes the technical background, recent trends in standard optical connectors, and recent issues related to photonic connection technologies.

Telecom- and Signal Relays with gastight plastic sealed housings enables the usage of inert and highly insulating gases. Although plastic sealed housings are used, optimized designs can keep the gas during the entire life of more than 25 years. The application of this technology allows the application of highly insulting gases like SF6 and result in a significant reduction of the relay size as reduced physical dimensions can be applied. With unchanged distances a significantly better dielectric performance can be achieved, without a relevant cost increase. Furthermore the inert switching atmosphere increases the switching characteristics or reduces the consumption of precious metals for the contacts. Even the usage of less precious metals like tungsten or ruthenium might be possible for switching typical telecommunication signals.

A three-mode switched-LNA has been developed using a 0.25 µm SiGe BiCMOS technology. The LNA features low noise figure (NF) performance, while achieving both low dissipation power and low distortion characteristics. The proposed MOSFET switch incorporating a newly developed switch circuit with a triple-well structure, which changes the LNA's mode, provides a parasitic capacitance of just 0.52 times that of a conventional MOSFET switch. This results in a significant NF improvement, by 0.16-0.33 dB, for the three-mode switched-LNA compared to a conventional LNA. Extensive studies of the MOSFET switch with regard to the structural parameters and the doping profiles are reported. Experimental results and the overall performance of a trial IC incorporating the three-mode switched-LNA are also given.

This paper describes the design, fabrication, and measurement of a sequential-rotation microstrip-array antenna for Electronic Toll Collection System (ETCS). The ETCS is made possible by using roadside equipment with a radiation pattern that can accurately pinpoint the designated communication area, without interference from other lanes. The sequential-rotation microstrip-array antenna is designed and an absorber attached to the antenna is considered to reduce the side lobe level (SLL) for the antenna of ETCS. Results show that the antenna yields a return loss at a center frequency of -20.675 dB, an axial ratio of 1.15 dB, and a gain of 20.26 dBi.

Design patterns can be regarded as an approach to encapsulate and reuse good design practices. However, most design patterns are specified using informal text and examples. To obtain all of the benefits of patterns, formal specification and tool support are indispensable. This paper proposes a Design Pattern Specification Language (DPSL) that is both manageable and effective. The DPSL provides software developers with the capability to treat design patterns as concrete design units without lowering abstraction. To demonstrate the usability of our DPSL and its application in design modeling, we have developed a prototype tool that supports the DPSL in UML diagrams. This prototype allows us to demonstrate the tool's support possibilities and the usability of patterns for software development applications.

In this paper, we propose an efficient requantization method for transcoding of MPEG video. Transcoding is the process of converting a compressed video format to another different compressed video format. We propose an simple and efficient transcoding by requantization in which MPEG coded video at high bit-rate is converted into MPEG bitstream at lower bit-rate. To reduce a image quality degradation, we use HVS (Human Visual System). By using this effect, the part of image in high activity region is coarsely quantized without seriously degrading the image quality. Experimental results show that the proposed method can provide good performance.

This paper describes the design of a 2.7 V operational, 200 MS/s, 14-bit CMOS D/A converter (DAC). The DAC consists of 63 current cells in matrix form for an upper 6-bit sub-DAC, and 8 current cells and R-2R ladder resistors for a lower 8-bit sub-DAC. A source degeneration resistor, for which a transistor in the triode operational region is used, is connected to the source of a MOS current source transistor in a current cell in order to reduce the influence of threshold voltage (Vth) variation and to satisfy the differential nonlinearity error specification as a 14-bit DAC. In conventional high-speed and high-resolution DACs that have the same design specifications described here, spurious-free dynamic range (SFDR) characteristics commonly deteriorate drastically as the frequency of the reconstructed waveform increases. The causes of this deterioration were carefully examined in the present study, finding that the deterioration is caused in part by the input-data-dependent time-constant change at the output terminal. Unexpected current flow in parasitic capacitors associated with current sources causes the change in the output current depending on the input data, resulting in time-constant change. In order to solve this problem, we propose a new output circuit to fix the voltage at the node where the outputs of the current sources are combined. SPICE circuit simulation demonstrates that 63 dB of SFDR characteristics for the 90 MHz reconstructed waveform at the output can be realizable when the supply voltage is 2.7 V, the clock rate is 200 MS/s, and the power dissipation is estimated to be 300 mW.

The low phase noise, low supply voltage 1.3 GHz CMOS VCO has been realized by 0.25 µm standard CMOS technology without any trimming and any tuning. The phase noise characteristics of -109 dBc/Hz and -123 dBc/Hz at 100 kHz offset and 500 kHz offset were achieved from carrier, respectively, with 1.3 GHz oscillation frequency at 1.4 V supply voltage. The performance of 1.4 V supply voltage phase noise was superior to that of 2.0 V supply voltage phase noise due to low output impedance current source. The tuning ranges of 13.3%, 16.6%, and 20.1% for 1.4 V, 1.8 V, and 2.0 V supply voltage were achieved, respectively. The amplifier consisted of one pair of PMOS differential stage with large gate length NMOS current source to realize low supply voltage operation and to avoid flicker noise contribution for phase noise. The on-chip spiral inductor consisted of three terminals arranged in a special shape to obtain high Q and small chip area. The power dissipation of this VCO was 22.4 mW without buffer amplifier.

An experimental equation of V-I characteristics of breaking arc was investigated in the air at atmospheric pressure. Material of the contact pair is Ag, Au, Cu and Ni. Supply voltage is set to 42, 48 and 54 V. The electrical resistance of experimental circuit is 5 Ω. The time evolutions of arc voltage, arc current and gap length were measured, simultaneously. V-I characteristics were obtained from those measured values. The dependence of the arc voltage on the gap length was represented by an approximate formula as a straight line in order to obtain the experimental equation. And the dependence of the strength of electric field of arc column on the supply voltage was approximated to a straight line. Using these approximate formulae, the experimental equation of the dependence of the arc voltage on the arc current was obtained with the gap length as a parameter. It was shown that the experimental equation agreed with experimental data in the experimental conditions for each contact material.

Arc duration of silver contacts was measured with fixed short gap under the condition of different constant gaps and different constant currents, which are close to the minimum arc current of the contact material. The results indicated that the arc occurred even at the current less than the minimum arc current. The arc duration varies in different operations at the same testing condition and it distributes exponentially in the time range up to 100 microseconds. The time constant τ and the extinction rate λ of the distribution were calculated, and related to the arc current. It was assured by silver electrode arc that, even below the so-called minimum arc current, arc ignition may occur but, in this case, the arc duration is momentary, and, as the arc current decreases, the arc extinction rate becomes large.

The interrupting characteristics of low voltage current limiting circuit breakers have directly relationship with the magnitude and distribution of magnetic field produced by contact system and splitter plates. In order to analyze the influence of configuration of contact system on current limiting characteristics, 3D magnetic field of arc chamber (including contact system, arc, splitter plates) is calculated. Furthermore, the electromagnetic repulsion force of movable contact is also calculated. The results can be used to improve configuration of arc quenching chamber. The cooperation between operating mechanism and electromagnetic repulsion force is also analyzed in this paper.