An adaptively phase-shift controlled self-injection locked VCO is described. A self-injection locking technique is effective to reduce phase noise. However, a conventional self-injection locked VCO has drawbacks of discontinuous frequency sweep which means narrow bandwidth, and large variation of phase noise. Our proposed adaptively phase-shift controlled self-injection locked VCO overcomes these drawbacks by detecting phase-shift of the self-injection feedback and controlling the phase-shift depending on sweep of the oscillation frequency. This paper describes analysis of relationships between the discontinuity and feedback phase-shift of the self-injection locked VCO. In addition, a VCO-IC which includes a Ka-band VCO and a phase detector is designed and fabricated in 0.18um SiGe BiCMOS technology. Measurement results of the proposed self-injection locked VCO using the fabricated IC show the improvement to the drawbacks. In the proposed self-injection locked VCO, the oscillation frequency sweep is continuous and the phase noise variation is less than 5 dB.

It is shown that an infinite lumped-element LC- ladder network generates all Bessel functions Jn(t) of the first kind as a response to a single non-zero initial condition. Closed-form expressions for the voltage responses in the time domain are presented if the LC- ladder is driven by a step-like input voltage.

This paper proposes a coarse-fine Time-to-Digital Converter (TDC), based on a Ring-Tapped Delay Line (RTDL). The TDC achieves the picosecond's level timing resolution and microsecond's level dynamic range at low cost. The TDC is composed of two coarse time measurement blocks, a time residue generator, and a fine time measurement block. In the coarse blocks, RTDL is constructed by redesigning the conventional Tapped Delay Line (TDL) in a ring structure. A 12-bit counter is employed in one of the two coarse blocks to count the cycle times of the signal traveling in the RTDL. In this way, the input range is increased up to 20.3µs without use of an external reference clock. Besides, the setup time of soft-edged D-flip-flops (SDFFs) adopted in RTDL is set to zero. The adjustable time residue generator picks up the time residue of the coarse block and propagates the residue to the fine block. In the fine block, we use a Vernier Ring Oscillator (VRO) with MOS capacitors to achieve a scalable timing resolution of 11.8ps (1 LSB). Experimental results show that the measured characteristic curve has high-level linearity; the measured DNL and INL are within ± 0.6 LSB and ± 1.5 LSB, respectively. When stimulated by constant interval input, the standard deviation of the system is below 0.35 LSB. The dead time of the proposed TDC is less than 650ps. When operating at 5 MSPS at 3.3V power supply, the power consumption of the chip is 21.5mW. Owing to the use of RTDL and VRO structures, the chip core area is only 0.35mm × 0.28mm in a 0.35µm CMOS process.

The impact of non-ideal delay line (DL) along with group delay ripple (GDR) on the performance of ultra wide bandwidth (UWB) system has not yet been studied in previous literatures. In this paper, according to the currently designed DLs, we propose a statistical GDR model to achieve a practical UWB DL, and investigate the degradation in average bit error rate (BER) caused by the GDR for the transmitted-reference (TR) UWB communication systems. According to the analysis results, an improved autocorrelation receiver (AcR) is proposed. Through Monte Carlo simulations, the great performance improvement of the proposed AcR is verified by comparing it with the conventional TR AcR under non-ideal DL conditions. The proposed receiver framework is simple enough to enable a tractable analysis, and provides valuable insights for designing a practical TR UWB AcR that experiences GDR.

A hybrid buffer structured optical packet switch and its scheduling algorithm are presented for a limited number of tunable wavelength convertors (TWCs) and internal wavelengths. The hybrid buffer consists of the fiber delay line (FDL) buffer and the electronic buffer. With the proposed algorithm, it could lead realizable packet loss reduction that the LAUC-VF algorithm with only the FDL buffer does not reach. Also, we optimized the number of TWCs and internal wavelengths of the hybrid buffer structured OPS. For the fully shared TWC structure, the optimum number of TWCs and internal wavelengths to guarantee minimum packet loss is evaluated to prevent resource waste under the hybrid buffer.

A UWB impulse array antenna (IAA) utilizing a novel electrical scanning system with tapped delay lines is proposed and its usefulness is experimentally verified. The experimental antenna is composed of impulse generators installed in each antenna element and tapped delay lines used for creating transmitting trigger signals, which is a simple circuit configuration. It is shown that the output phase of the transmitting wave can be controlled by controlling the period of the trigger signal, and beam direction can be controlled from -30 deg to +30 deg by changing the trigger frequency from Fc-2 kHz to Fc+2 kHz. Evaluation of this antenna as a short range radar is carried out and distance resolution of 25 cm and angle resolution below 10 deg are obtained.

A high-throughput on-chip monitoring circuit with a digital output is proposed for the variations of the NMOS and PMOS threshold voltages. A voltage-controlled delay line (VCDL) and a time-to-digital converter (TDC) are used to convert a small difference in analog voltage into a large difference in time delay. This circuit was applied to the transistors of W = 10 µm and L = 0.18 µm in a 1616 array matrix fabricated with a 0.18-µm process. The measurement of the threshold voltage shows that the maximum peak-to-peak intra-chip variation of NMOS and PMOS transistors are about 31.7 mV and 32.2 mV, respectively, for the temperature range from -25 to 75. The voltage resolutions of NMOS and PMOS transistors are measured to be 1.10 mV/bit and 3.53 mV/bit at 25, respectively. The 8-bit digital code is generated for the threshold voltage of a transistor in every 125 ns, which corresponds to the 8-MHz throughput.

This paper proposes a new overlay transmission system for wireless LAN with RTS/CTS exchange. Conventional timing synchronization schemes may fail in the presence of inter-system interference, because they have not been designed for overlay transmission. In the proposed system, a transmitter estimates the transmission timing of the next wireless LAN DATA frame, and then sends its DATA frame at almost the same time as the estimated transmission timing to easily establish timing synchronization at the receiver. Moreover, we employ a tapped delay line adaptive array antenna at both transmitter and receiver to effectively suppress interference due to overlay transmission in a rich multipath propagation environment. The frame error rate performances of the proposed system and the IEEE 802.11a wireless LAN are evaluated through computer simulations that assume an exponentially decaying 8-path non-line-of-sight fading channel and include a timing synchronization process. Simulation results demonstrate that the proposed system can achieve overlay transmission while avoiding interference in a rich multipath propagation environment.

This paper presents a Time Difference Amplifier (TDA) that amplifies the input time difference into the output time difference. Cross coupled chains of variable delay cells with the same number of stages are applicable for TDA, and the gain is adjusted via the closed-loop control. The TDA was fabricated using 65 nm CMOS and the measurement results show that the time difference gain is 4.78 at a nominal power supply while the designed gain is 4.0. The gain is stable enough to be less than 1.4% gain shift under 10% power supply voltage fluctuation.

We focus on non-conflicting construction of an optical multistage feedforward network to emulate the N-to-1 output buffer multiplexer by using switched fiber delay line (SDL). In [1], Y.T. Chen et al. presented a sufficient condition (an upper bound) for the number of delay lines required for such a multiplexer with variable length bursts. In this paper, we first give an improved upper bound. Then we develop a framework to construct an arrival case of bursts which can be used to achieve a necessary condition (a lower bound). These results are further extended to the feedforward construction of N-to-N output buffer switch. Through simulation and performance comparison, we find that the new bounds can significantly decrease the hardware cost for constructing both the feedforward SDL-based multiplexer and output buffer switch while still provide the same performance as that of the old ones.

We propose an implementation of the tapped delay line adaptive array (TDLAA) at the base station for improving the BER performance of asynchronous multi-user mobile communication over fast fading channels using multiple antennas. The data of each user at the mobile station, which applies two transmit antennas, are encoded by Space Time Block Code (STBC). The proposed scheme transmits the pilot signal and information data in alternate time slots. We derive performance criteria for designing such a scheme under the assumption that the fading is classified as fast fading. We show that the proposed scheme can suppress co-channel interference (CCI) and defeat Doppler spread effectively.

This paper presents a mathematically simple method of maximum SINR (Signal to Interference plus Noise Ratio) design of broadband MIMO (Multiple Input Multiple Output) communication systems adopting TDL (Tapped Delay Line) structure for spatio-temporal processing in both transmitter and receiver sides. The weight vectors in both ends are determined alternately, optimizing one side by fixing the other, and this operation is repeated until the SINR converges. The performance of MIMO systems using the proposed approach is investigated through computer simulations, and it is demonstrated that, though it requires high computational cost, the TDL structure brings high ability to mitigate the influence of frequency selective fading, particularly when the duration of the delay profile is long. Moreover, experimental results show that the equable distribution of the resources (weights and delay units) to both arrays is better choice than the concentration of them to one side of the transmitter or receiver.

Acoustic field analysis results of surface acoustic wave dispersive delay lines using inclined chirp IDTs on a Y-Z LiNbO3 substrate are described. The calculated results are compared with optical measurements. The angular spectrum of the plane wave method is applied to calculation of the acoustic fields considering the anisotropy of the SAW velocity by using the polynomial approximation. Acoustic field propagating along the Z-axis of the substrate, which is the main beam excited by the inclined chirp IDT, shows asymmetric distribution between the +Z and -Z directions. Furthermore the SAW beam propagating in a slanted direction with an angle of +18 from the Z axis to the X-axis is observed. It is described that the SAW beam propagating in a slanted direction is the first side lobe excited by the inclined chirp IDT. The acoustic field shows asymmetric distribution along the X-axis because of the asymmetric structure of the inclined chirp IDT. Finally, acoustic field of a two-IDT connected structure which consists of the same IDTs electrically connected in series is presented. The acoustic field of the two-IDT connected structure is calculated to be superposed onto the calculated result of the acoustic field exited by one IDT on the calculated result shifted along the X-axis. Two SAW beams excited by IDTs are observed. The distributions of the SAW beams are not in parallel. The calculated results show good agreement with the optical measurement results.

In an effort to reduce switch cost, we present the optimum numbers of tunable wavelength converters (TWCs) and internal wavelengths required for contention resolution of asynchronous and variable length packets, in the optical packet switch (OPS) with the shared fiber delay line (FDL) buffer. To optimize TWCs and internal wavelengths related to OPS design cost, we proposed a scheduling algorithm for the limited TWCs and internal wavelengths. For three TWC alternatives (not shared, partially shared, and fully shared cases), the optimum numbers of TWCs and internal wavelengths to guarantee minimum packet loss are evaluated to prevent resource waste. Under a given load, TWCs and internal wavelengths could be significantly reduced, guaranteeing the same packet loss as the performance of an OPS with full TWCs and internal wavelengths.

This paper presents a simple method to determine weights of single carrier multiple input multiple output (MIMO) broadband communication systems adopting tapped delay line (TDL) structure in receiver side for the effective communication under frequency selective fading (FSF) environment. First, assuming the perfect knowledge of the channel matrix in both arrays, an iterative design method of transmitter and receiver weights is proposed. In this approach, both weights are determined alternately to maximize signal to noise plus interference ratio (SINR) by fixing the weight of one side while optimizing the other, and this operation is repeated until SINR converges. Next, considering the case of uninformed transmitter, maximum SINR design method of MIMO system is extended for space time block coding (STBC) scheme working under FSF. Through computer simulations, it is demonstrated that the proposed schemes achieves higher SINR than conventional method with delay-less structure, particularly for the fading with long duration.

We implemented all-fiber delay line using linearly chirped fiber Bragg gratings (CFBG), which can be applicable for reflectometry or optical coherence tomography (OCT). Compared with the previously reported delay lines, the proposed fiber-based optical delay line has in principle novel advantages such as automatic dispersion cancellations without additional treatment and a gain in optical delay that is dependent on parameters of used CFBGs. Dispersion compensation in optical delay line (ODL), which is the indispensable problem in bulk optics based ODL, is demonstrated in fiber by using two identical but reversely ordered CFBGs. Amplified variable optical delay of around 2.5 mm can be obtained by applying small physical stretching of one of CFBGs in the proposed scheme. The operational principles of the all-fiber variable optical delay line, which are based on the distributed reflection characteristic of a CFBG employed, are described. Especially properties such as in-line automatic dispersion cancellation and amplified optical delay under strain are dealt. To demonstrate the properties of the proposed scheme, which is theoretical consequences under assumptions, an all-fiber optical delay line have been implemented using fiber optic components such as fiber couplers and fiber circulators. With the implanted ODL, the group delay and amplified optical delay length was measured with/without strain. The wavelength independent group delay measured within reflection bandwidth of the CFBG has proved the property of automatic dispersion cancellations in the proposed fiber delay line. Optical delay length of 2.5 mm was obtained when we apply small physical stretching to the CFBG by 100 µm and this is expressed by the amplification factor of 25. Amplification factor 25, which is less than theoretical value of 34 due to slipping of fiber in the fiber holder, shows that the proposed scheme can provide large optical delay with applying small physical stretching to the CFBG. We measure slide glass thickness to check the performance of the fiber delay line and the good agreement in measured and physical thickness of slide glass (1 mm thick) validates the potential of proposed delay line in the applications of optical reflectometry and OCT. We also discuss the problem and the solution to improve the performance.

Optical Burst Switching (OBS) has been developed as an efficient switching technique to exploit the capacity provided by Wavelength Division Multiplexing (WDM) transmission technology for the next generation optical Internet. One critical design issue in OBS is how to provide Quality-of-Service (QoS) on optical networks. In order to provide the service differentiation, we propose in this paper a buffer allocation algorithm to schedule bursts at the edge OBS nodes, a bandwidth allocation algorithm and a Fiber Delay Line (FDL) allocation algorithm to schedule bursts at the core OBS nodes. We also introduce a new burst assembly technique in which the burst is generated either when the sum of the collected packet sizes reaches the maximum threshold or when the burst assembling time reaches the timeout limit. Our simulation results show that the proposed algorithms achieve the controllable burst loss probability for different service classes. The bandwidth allocation algorithm performs very well at the core OBS nodes in terms of the low loss probability.

We study photonic packet switches to support asynchronously arriving variable-length packets. A scheduler for contention resolution is operated in electrical domain even when data street of the buffer is provided in optical domain. In this scheme, the scheduler may be a bottleneck. To compensate the gap of high-speed optical transmission and slow-speed electronic processing, we propose a multi-stage fiber delay line (FDL) buffer architecture that forms a tree structure in which each node has a block of FDLs and a scheduler. This is especially useful for output-buffer switches in which scheduling complexity is proportional to the number of ports of the packet switch. Through a newly-developed approximate analytical method, we show the optimum unit length of the fiber delay lines to decrease packet loss probability. We also show the sufficient number of FDLs in the two-stage buffer.

This letter describes consecutive zero and one bits detection circuits designed for a 1.25 Gbit/s burst mode laser driver realized in a SiGe 0.35 µm BiCMOS technology with 3.3 V power supply. The architecture is based on a frequency divider and a delay line counting per four consecutive zero or one bits. The detector was designed with high-speed split-output stage flip-flops modified to have a reset input. Experimental results validate the design of the detector.

We propose an optical packet switch (OPS) using a hybrid buffer structure for the contention resolution of asynchronous variable length packets. The hybrid buffer consists of a fiber delay line (FDL) buffer as the prime buffer and a shared electronic buffer as the supplementary buffer. For the performance evaluation, a modified void filling scheduling algorithm that can be applied to the OPS was proposed. Simulation results show that the use of the electronic buffer together with the FDL buffer significantly reduce the number of FDLs required for contention resolution and considerably lower packet loss.