This paper presents a hippocampal cognitive prosthesis chip designed for restoring the ability to form new long-term memories due to hippocampal system damage. The system-on-chip (SOC) consists of a 16-channel micro-power low-noise amplifier (LNA), high-pass filters, analog-digital converters (ADCs), a 16-channel spike-sorter, a generalized Laguerre-Volterra model multi-input, multi-output (GLVM-MIMO) hippocampal processor, an 8-channel neural stimulator and peripheral circuits. The proposed LNA achieved a voltage gain of 50dB, input-referred noise of 3.95µVrms, and noise efficiency factor (NEF) of 3.45 with the power consumption of 3.3µW. High-pass filters with a 300-Hz bandwidth are used to filter out the unwanted local field potential (LFP). 4 12-bit successive approximation register (SAR) ADCs with a signal-to-noise-and-distortion ratio (SNDR) of 63.37dB are designed for the digitization of the neural signals. A 16-channel spike-sorter has been integrated in the chip enabling a detection accuracy of 98.3% and a classification accuracy of 93.4% with power consumption of 19µW/ch. The MIMO hippocampal model processor predict output spatio-temporal patterns in CA1 according to the recorded input spatio-temporal patterns in CA3. The neural stimulator performs bipolar, symmetrical charge-balanced stimulation with a maximum current of 310µA, triggered by the processor output. The chip has been fabricated in 40nm standard CMOS technology, occupying a silicon area of 3mm2.

The total number of solar power-producing facilities whose Feed-in Tariff (FIT) Program-based ten-year contracts will expire by 2023 is expected to reach approximately 1.65 million in Japan. If the facilities that produce or consume renewable energy would increase to reach a large number, e.g., two million, blockchain would not be capable of processing all the transactions. In this work, we propose a blockchain-based electricity-tracking platform for renewable energy, called ‘ZGridBC,’ which consists of mutually cooperative two novel decentralized schemes to solve scalability, storage cost, and privacy issues at the same time. One is the electricity production resource management, which is an efficient data management scheme that manages electricity production resources (EPRs) on the blockchain by using UTXO tokens extended to two-dimension (period and electricity amount) to prevent double-spending. The other is the electricity-tracking proof, which is a massive data aggregation scheme that significantly reduces the amount of data managed on the blockchain by using zero-knowledge proof (ZKP). Thereafter, we illustrate the architecture of ZGridBC, consider its scalability, security, and privacy, and illustrate the implementation of ZGridBC. Finally, we evaluate the scalability of ZGridBC, which handles two million electricity facilities with far less cost per environmental value compared with the price of the environmental value proposed by METI (=0.3 yen/kWh).

In CRYPTO 2019, Gohr first introduced the deep learning method to cryptanalysis for SPECK32/64. A differential-neural distinguisher was obtained using ResNet neural network. Zhang et al. used multiple parallel convolutional layers with different kernel sizes to capture information from multiple dimensions, thus improving the accuracy or obtaining a more round of distinguisher for SPECK32/64 and SIMON32/64. Inspired by Zhang's work, we apply the network structure to other ciphers. We not only improve the accuracy of the distinguisher, but also increase the number of rounds of the distinguisher, that is, distinguish more rounds of ciphertext and random number for DES, Chaskey and PRESENT.

Since the dark channel prior (DCP)-based dehazing method is ineffective in the sky area and will cause the problem of too dark and color distortion of the image, we propose a novel dehazing method based on sky area segmentation and image fusion. We first segment the image according to the characteristics of the sky area and non-sky area of the image, then estimate the atmospheric light and transmission map according to the DCP and correct them, and then fuse the original image after the contrast adaptive histogram equalization to improve the details information of the image. Experiments illustrate that our method performs well in dehazing and can reduce image distortion.

Single image deraining is an ill-posed problem which also has been a long-standing issue. In past few years, convolutional neural network (CNN) methods almost dominated the computer vision and achieved considerable success in image deraining. Recently the Swin Transformer-based model also showed impressive performance, even surpassed the CNN-based methods and became the state-of-the-art on high-level vision tasks. Therefore, we attempt to introduce Swin Transformer to deraining tasks. In this paper, we propose a deraining model with two sub-networks. The first sub-network includes two branches. Rain Recognition Network is a Unet with the Swin Transformer layer, which works as preliminarily restoring the background especially for the location where rain streaks appear. Detail Complement Network can extract the background detail beneath the rain streak. The second sub-network which called Refine-Unet utilizes the output of the previous one to further restore the image. Through experiments, our network achieves improvements on single image deraining compared with the previous Transformer research.

Convolutional Neural Networks (CNNs) have shown remarkable performance in image recognition tasks. In this letter, we propose a new CNN model called the EnsNet which is composed of one base CNN and multiple Fully Connected SubNetworks (FCSNs). In this model, the set of feature maps generated by the last convolutional layer in the base CNN is divided along channels into disjoint subsets, and these subsets are assigned to the FCSNs. Each of the FCSNs is trained independent of others so that it can predict the class label of each feature map in the subset assigned to it. The output of the overall model is determined by majority vote of the base CNN and the FCSNs. Experimental results using the MNIST, Fashion-MNIST and CIFAR-10 datasets show that the proposed approach further improves the performance of CNNs. In particular, an EnsNet achieves a state-of-the-art error rate of 0.16% on MNIST.

Speech emotion recognition (SER) has been a complex and difficult task for a long time due to emotional complexity. In this paper, we propose a multitask deep learning approach based on cascaded attention network and self-adaption loss for SER. First, non-personalized features are extracted to represent the process of emotion change while reducing external variables' influence. Second, to highlight salient speech emotion features, a cascade attention network is proposed, where spatial temporal attention can effectively locate the regions of speech that express emotion, while self-attention reduces the dependence on external information. Finally, the influence brought by the differences in gender and human perception of external information is alleviated by using a multitask learning strategy, where a self-adaption loss is introduced to determine the weights of different tasks dynamically. Experimental results on IEMOCAP dataset demonstrate that our method gains an absolute improvement of 1.97% and 0.91% over state-of-the-art strategies in terms of weighted accuracy (WA) and unweighted accuracy (UA), respectively.

The application of time-series prediction is very extensive, and it is an important problem across many fields, such as stock prediction, sales prediction, and loan prediction and so on, which play a great value in production and life. It requires that the model can effectively capture the long-term feature dependence between the output and input. Recent studies show that Transformer can improve the prediction ability of time-series. However, Transformer has some problems that make it unable to be directly applied to time-series prediction, such as: (1) Local agnosticism: Self-attention in Transformer is not sensitive to short-term feature dependence, which leads to model anomalies in time-series; (2) Memory bottleneck: The spatial complexity of regular transformation increases twice with the sequence length, making direct modeling of long time-series infeasible. In order to solve these problems, this paper designs an efficient model for long time-series prediction. It is a double pyramid bidirectional feature fusion mechanism network with parallel Temporal Convolution Network (TCN) and FastFormer. This network structure can combine the time series fine-grained information captured by the Temporal Convolution Network with the global interactive information captured by FastFormer, it can well handle the time series prediction problem.

Uncovered muck truck detection aims to detect the muck truck and distinguish whether it is covered or not by dust-proof net to trace the source of pollution. Unlike traditional detection problem, recalling all uncovered trucks is more important than accurate locating for pollution traceability. When two objects are very close in an image, the occluded object may not be recalled because the non-maximum suppression (NMS) algorithm can remove the overlapped proposal. To address this issue, we propose a Location First NMS method to match the ground truth boxes and predicted boxes by position rather than class identifier (ID) in the training stage. Firstly, a box matching method is introduced to re-assign the predicted box ID using the closest ground truth one, which can avoid object missing when the IoU of two proposals is greater than the threshold. Secondly, we design a loss function to adapt the proposed algorithm. Thirdly, a uncovered muck truck detection system is designed using the method in a real scene. Experiment results show the effectiveness of the proposed method.

In this paper, we propose a heuristic planning method to efficiently accommodate dynamic multilayer path (MLP) demand in multilayer networks consisting of a Time Division Multiplexing (TDM) layer and a Wavelength Division Multiplexing (WDM) layer; the goal is to achieve the flexible accommodation of increasing capacity and diversifying path demands. In addition to the grooming of links at the TDM layer and the route and frequency slots for the elastic optical path to be established, MLP requires the selection of an appropriate operational mode, consisting of a combination of modulation formats and symbol rates supported by digital coherent transceivers. Our proposed MLP planning method defines a planning policy for each of these parameters and embeds the values calculated by combining these policies in an auxiliary graph, which allows the planning parameters to be calculated for MLP demand requirements in a single step. Simulations reveal that the choice of operational mode significantly reduces the blocking probability and demonstrate that the edge weights in the auxiliary graph allow MLP planning with characteristics tailored to MLP demand and network requirements. Furthermore, we quantitatively evaluate the impact of each planning policy on the MLP planning results.

Network Functional Virtualization (NFV) is a high-performance network interconnection technology that allows access to traditional network transport devices through virtual network links. It is widely used in cloud computing and other high-concurrent access environments. However, there is a long delay in the introduction of software NFV solutions. Other hardware I/O virtualization solutions don't scale very well. Therefore, this paper proposes a virtualization implementation method on 100Gbps high-speed Field Programmable Gate Array (FPGA) network accelerator card, which uses FPGA accelerator to improve the performance of virtual network devices. This method uses the single root I/O virtualization (SR-IOV) technology to allow 256 virtual links to be created for a single Peripheral Component Interconnect express (PCIe) device. And it supports data transfer with virtual machine (VM) in the way of Peripheral Component Interconnect (PCI) passthrough. In addition, the design also adopts the shared extensible queue management mechanism, which supports the flexible allocation of more than 10,000 queues on virtual machines, and ensures the good isolation performance in the data path and control path. The design provides high-bandwidth transmission performance of more than 90Gbps for the entire network system, meeting the performance requirements of hyperscale cloud computing clusters.

To achieve the extreme high data rate and extreme coverage extension requirements of 6G wireless communication, new spectrum in sub-THz (100-300GHz) and non-terrestrial network (NTN) are two of the macro trends of 6G candidate technologies, respectively. However, non-linearity of power amplifiers (PA) is a critical challenge for both sub-THz and NTN. Therefore, high power efficiency (PE) or low peak to average power ratio (PAPR) waveform design becomes one of the most significant 6G research topics. Meanwhile, high spectral efficiency (SE) and low out-of-band emission (OOBE) are still important key performance indicators (KPIs) for 6G waveform design. Single-carrier waveform discrete Fourier transform spreading orthogonal frequency division multiplexing (DFT-s-OFDM) has achieved many research interests due to its high PE, and it has been supported in 5G New Radio (NR) when uplink coverage is limited. So DFT-s-OFDM can be regarded as a candidate waveform for 6G. Many enhancement schemes based on DFT-s-OFDM have been proposed, including null cyclic prefix (NCP)/unique word (UW), frequency-domain spectral shaping (FDSS), and time-domain compression and expansion (TD-CE), etc. However, there is no unified framework to be compatible with all the enhancement schemes. This paper firstly provides a general description of the 6G candidate waveforms based on DFT-s-OFDM enhancement. Secondly, the more flexible TD-CE supporting methods for unified non-orthogonal waveform (uNOW) are proposed and discussed. Thirdly, a unified waveform framework based on DFT-s-OFDM structure is proposed. By designing the pre-processing and post-processing modules before and after DFT in the unified waveform framework, the three technical methods (NCP/UW, FDSS, and TD-CE) can be integrated to improve three KPIs of DFT-s-OFDM simultaneously with high flexibility. Then the implementation complexity of the 6G candidate waveforms are analyzed and compared. Performance of different DFT-s-OFDM enhancement schemes is investigated by link level simulation, which reveals that uNOW can achieve the best PAPR performance among all the 6G candidate waveforms. When considering PA back-off, uNOW can achieve 124% throughput gain compared to traditional DFT-s-OFDM.

Improvement of the on/off ratio in organic field-effect transistors through the use of pentacene and molybdenum trioxide (MoO3) layers was attempted via the preparation of a discontinuous MoO3 layer using a mesh mask. We prepared three types of devices. Device A had a conventional top-contact structure with an n-type Si wafer and a 200-nm-thick SiO2 film onto which we deposited a 70-nm-thick pentacene film and a 30-nm-thick layer of Au top electrodes. Devices B and C had a similar structure to device A but received a continuous and a discontinuous MoO3 layer, respectively. The off current in Device B was remarkably high; in contrast, the off current in Device C was reduced and dependent on the separation of the MoO3 layer. It was deduced that the high resistance of the area without MoO3 contributed to the reduced off current.

In this report, solar cell characteristics were evaluated by doping the active layer CH3NH3PbI3 (MAPbI3) with 3.0 vol% and 6.0 vol% of potassium ion (KI) in an inverse-structured perovskite solar cells (PSCs). The Tauc plots of the absorbance characteristics and the ionization potential characteristics show that the top end of the valence band shifted by 0.21eV in the shallow direction from -5.34eV to -5.13eV, and the energy band gap decreased from 1.530eV to 1.525eV. Also, the XRD measurements show that the lattice constant decreased from 8.96Å to 8.93Å when KI was doped. The decrease in the lattice constant indicates that a part of the A site is replaced from methylammonium ion (MAI) to KI. In the J-V characteristics of the solar cell, the mean value of Jsc improved from 7.0mA/cm2 without KI to 8.8mA/cm2 with 3.0 vol% of KI doped and to 10.2mA/cm2 with 6.0 vol% of KI doped. As a result, the mean value of power-conversion efficiency (PCE) without KI was 3.5%, but the mean value of PCE improved to 5.2% with 3.0 vol% of KI doped and to 4.5% with 6.0 vol% of KI doped. Thus, it has shown that it is effective to dope KI to MAIPBI3, which serves as the active layer, even in the inverse-structured PSCs.

Lead bromide-based perovskite organic-inorganic quantum-well films incorporated polycyclic aromatic chromophores into the organic layer (in other words, hybrid quantum-wells combined lead bromide semiconductor and organic semiconductors) were prepared by use of the spin-coating technique from the DMF solution in which PbBr2 and alkyl ammonium bromides which were linked polycyclic aromatics, pyrene, phenanthrene, and anthracene. When the pyrene-linked methyl ammonium bromide, which has a relatively small molecular cross-section with regard to the inorganic semiconductor plane, was employed, a lead bromide-based perovskite structure was successfully formed in the spin-coated films. When the phenanthrene-linked and anthracene-linked ammonium bromides, whose chromophore have large molecular cross-sections, were employed, lead bromide-based perovskite structures were not formed. However, the introduction of longer alkyl chains into the aromatics-linked ammonium bromides made it possible to form the perovskite structure.

An enzymatic biofuel cell (BFC) that uses lactic acid in human sweat as fuel to generate electricity is an attractive power source for wearable devices. A BFC capable of generating electricity with human sweat has been developed. It comprised a flexible tattoo seal type battery with silver oxide vapor deposited on a flexible material and conductive carbon nanotubes printed on it. The anode and cathode in this battery were arranged in a plane (planar type). This work proposes a thin laminated enzymatic BFC by inserting a cellulose nanofiber (CNF) sheet between two electrodes to absorb human sweat (stack-type). Optimization of the anode and changing the arrangement of electrodes from planar to stack type improved the output and battery life. The stack type is 43.20μW / cm2 at 180mV, which is 1.25 times the maximum power density of the planar type.

Direct-current superconducting quantum interference device (dc-SQUID) based on intrinsic Josephson junction (IJJ) has been fabricated using Bi2Sr2CaCu2O8+δ (Bi-2212) films grown on MgO substrates with surface steps. The superconducting loop parallel to the film surface across the step edge contains two IJJ stacks along the edge. The number of crystallographically stacked IJJ for each SQUIDs were 40, 18 and 3. Those IJJ SQUIDs except for one with 40 stacked IJJs revealed clear periodic modulation of the critical current for the flux quanta through the loops. It is anticipated that phase locking of IJJ has an effect on the modulation depth of the IJJ dc-SQUID.

The supercomputer, “Fugaku”, which ranked number one in multiple supercomputing lists, including the Top500 in June 2020, has various power control features, such as (1) an eco mode that utilizes only one of two floating-point pipelines while decreasing the power supply to the chip; (2) a boost mode that increases clock frequency; and (3) a core retention feature that turns unused cores to the low-power state. By orchestrating these power-performance features while considering the characteristics of running applications, we can potentially gain even better system-level energy efficiency. In this paper, we report on the performance and power consumption of Fugaku using SPEC HPC benchmarks. Consequently, we confirmed that it is possible to reduce the energy by about 17% while improving the performance by about 2% from the normal mode by combining boost mode and eco mode.

The demand for low-latency transmission of large-capacity video, such as 4K and 8K, is increasing for various applications such as live-broadcast program production, sports viewing, and medical care. In the broadcast industry, low-latency video transmission is required in remote production, an emerging workflow for outside broadcasting. For ideal remote production, long-distance transmission of uncompressed 8K60p video signals, ultra-low latency less than 16.7 ms, and PTP synchronization through network are required; however, no existing video-transmission system fully satisfy these requirements. We focused on optical transport technologies capable of long-distance and large-capacity communication, which were previously used only in telecommunication-carrier networks. To fully utilize optical transport technologies, we propose the first-ever video-transmission system architecture capable of sending and receiving uncompressed 8K video directly through large-capacity optical paths. A transmission timing control in seamless protection switching is also proposed to improve the tolerance to network impairment. As a means of implementation, we focused on whitebox transponder, an emerging type of optical transponder with a disaggregation configuration. The disaggregation configuration enables flexible configuration changes, additional implementations, and cost reduction by separating various functions of optical transponders and controlling them with a standardized interface. We implemented the ultra-low-latency video-transmission system utilizing whitebox transponder Galileo. We developed a hardware plug-in unit for video transmission (VideoPIU), and software to control the VideoPIU. In the video-transmission experiments with 120-km optical fiber, we confirmed that it was capable of transmitting uncompressed 8K60p video stably in 1.3 ms latency and highly accurate PTP synchronization through the optical network, which was required in the ideal remote production. In addition, the application to immersive sports viewing is also presented. Consequently, excellent potential to support the unprecedented applications is demonstrated.

One key to implementing the smart city is letting the smart space know where and how many people are. The visual method is a scheme to recognize people with high accuracy, but concerns arise regarding potential privacy leakage and user nonacceptance. Besides, being functional in a limited environment in an emergency should also be considered. We propose a real-time people counting and tracking system based on a millimeter wave radar (mmWave) as an alternative to the optical solutions in a restaurant. The proposed method consists of four main procedures. First, capture the point cloud of obstacles and generate them using a low-cost, commercial off-the-shelf (COTS) mmWave radar. Next, cluster the individual point with similar properties. Then the same people in sequential frames would be associated with the tracking algorithm. Finally, the estimated people would be counted, tracked, and shown in the next frame. The experiment results show that our proposed system provided a median position error of 0.17 m and counting accuracy of 83.5% for ten insiders in various scenarios in an actual restaurant environment. In addition, the real-time estimation and visualization of people's numbers and positions show a potential capability to help prevent crowds during the pandemic of Covid-19 and analyze customer visitation patterns for efficient management and target marketing.