This paper describes the circuit design and experimental results of a video-rate 10-b analog-to-digital converter (ADC) suitable for consumer video products, such as high-definition TV sets. Triple-stage conversion scheme combined with two new conversion methods, "Dynamic Sliding Reference Method" and "Triangular Interpolation Method," and an internal Bi-CMOS Sample/Hold circuit have been developed. These conversion methods require no adjustment circuit to fit reference voltages between conversion stages and realize small active area. As a result, a maximum conversion frequency of 16 MHz, acceptable SNRs of 56 dB and 48 dB for 10 kHz and 8 MHz input frequency respectively and small DNLE of 0.75 LSB have been achieved. This ADC is fabricated with 1.2 µm Bi-CMOS technology and integrates very small number of bipolar transistors of 2 K on a small active area of 2.52.7 mm2 and consumes 350 mW.

This paper presents a mathematical formulation of a data path allocation and floorplanning problem using the mixed integer linear programming, and shows some experimental results. We assume that a data flow graph and the scheduled result are given in advance. The chip area and total wire length are used for the quality measures of the solution for the problem. This method is applied to some examples, and compared with the other method reported previously in the points of the solution and computation time.

For the efficient circuit simulation, several direct/relaxation-based mixed mode simulation techniques have been studied. This paper proposes the combination of selective trace, which is well-known in the logic simulation, with dynamic network separation. In the selective trace method, the time points to be analyzed are selected for each subcircuit. Since the separation technique enables the analysis of each subcircuit independently, it is possible to skip solving the latent subcircuits, according to selective trace. Selecting the time points in accordance with activity of each subcircuit is analogous to multirate numerical integration technique used in the waveform relaxation algorithm.

This paper describes mixed gas systems of SO2 and NO2 which are the essential corrosive gases in an ordinary atmospheric environment of electronic parts. It describes the corrosion product compositions and the behavior of copper in mixed and separate gases. Results of our tests show the following: (1) The weight of corrosion products with the SO2-NO2 mixed gas approximate the sum of those with the individual gases, however, the corrosion products of SO2 are affected by NO2. (2) Tests of the SO2-NO2 mixed gas closely simulates tests of electronic parts in the ordinary atmospheric environment.

This letter presents an algorithm named SPM which generates test patterns for single stuck-at faults in synchronous sequential circuits based on a product machine traversal method. The new idea presented in this letter is partitioned image computation combined with a mixed breadth-first/depth-first search. Image computation is carried out in partitioned manner by substituting constant logical values to some input variables. This brings about significant reduction in storage requirement during image computation. A test generator based on SPM achieved 100% fault efficiency for the ISCAS'89 benchmark circuits with not more than 32 flip-flops.

A technique for reducing fiber four-wave mixing (FWM) in multichannel transmissions is proposed. Birefringent elements are inserted on the way of transmission lines. Due to the effect of birefringent elements on the polarization states, the effective crosstalk due to FWM is expected to be 3/16 of that in the worst case in conventional systems.

This paper discusses the development of a monolithic image-rejection mixer with very wide-band (about 60% of the center frequency) image rejection characteristics for 16-QAM digital microwave radio communication receivers. The mixer can be commonly used in 4-, 5-, and 6-GHz bands, which reduces the cost. The mixer consists of a wide-band 90splitter, in-phase divider and drain LO injection mixers. They are designed on a single 2.81.8 mm2 GaAs chip based on a uniplanar MMIC lumped-constant element technique. The mixer achieved an image rejection ratio of greater than 25 dB and a conversion loss of less than 2 dB at a wide LO frequency range from 3.5 to 6.5 GHz, without consuming any DC power.

This paper describes a mixed mode circuit simulation by the direct and relaxation-based methods with dynamic network partitioning. For the efficient circuit simulation by the direct method, the algorithms with circuit partitioning and latency technique have been studied. Recently, the hierarchical decomposition and latency and their validities have been researched. Network tearing techniques enable independent analysis of each subnetwork except for the local datum nodes. Therefore, if the local datum nodes are also torn, each subnetwork is separated entirely. Since the network separation is based on relaxation approach, the implementation of the separation technique in the circuit simulation by the direct method corresponds to performing the mixed mode simulation by the direct and relaxation-based methods. In this paper, a dynamic "network separation" technique based on the tightness of the coupling between subnetworks is suggested. Then, by the introduction of dynamic network separation into the simulator SPLIT with hierarchical decomposition and latency, the mixed mode circuit simulator, which selects the direct method or the relaxation method and determines the block size of the latent circuit dynamically and suitably, is constructed.

This paper proposes fiber optic link configurations for use in microwave and millimeter-wave transmission Higher frequencies,such as millimeter-waves, are well suited to transmission of broadband signals. Photodiodes can operate simultaneously as optical detectors and microwave frequency mixers thanks to their inherent nonlinearities. This allows us to increase the output radio frequncy. But, this also generates undesired spurious frequencies, necessitating the use of microwave filters. We discuss here two fiber optic link configurations, i.e., balanced/image canceling photodiode mixing links utilizing the combination of microwave functional components and optical devices to suppress the local/image frequency without filters. These configurations are experimentally investigated at microwave frequencies and local/image frequency suppression is successfully demonstrated.

The performance of a traveling wave Mach-Zehnder external optical modulator (EOM) mixer is described and compared with a conventional diode mixer's performance. Additionally, by incorporating external circuitry, the EOM mixer can provide single sideband suppression in addition to the inherent local oscillator suppression. The basic frequency mixing function of the EOM mixer is first described theoretically and then extended to the sideband suppression case. The performance of both configurations is also presented. Achievable electrical isolation between LO (carrier) and RF (upconverted data signal at LOIF) frequencies is greater than 95 dB and total link conversion loss is 37 dB in this demonstration with a laser diode source. Sideband suppression of greater than 43 dB with respect to the desired sideband at the photodetector output is achieved.

This paper presents a method for LSI implementation of a long-tap acoustic echo canceller algorithm using the residue number system (RNS) and the mixed-radix number system (MRS). It also presents a quantitative comparison of echo canceller architectures, one using the RNS and the other using the binary number system (BNS). In the RNS, addition, subtraction, and multiplication are executed quickly but scaling, overflow detection, and division are difficult. For this reason, no echo canceller using the RNS has been implemented. We therefore try to design an echo canceller architecture using the RNS and the NLMS algorithm. It is shown that the echo canceller algorithm can be effectively implemented using the RNS by introducing the MRS. The quantitative comparison of echo canceller architectures shows that a long-tap acoustic echo canceller can be implemented more effectively in terms of chip size and power dissipation by the architecture using the RNS.

Thin-film YBCO Josephson junctions were successfully fabricated by a pulsed excimer laser ablation, and the mixing experiments in the microwave region (820 GHz) were carried out at the temperature of 77 K. The IF output maximum was obtained at the bias voltage midway between the zero and the first Shapiro steps for the fundamental mixing. For the 2nd harmocic mixing, the IF output maximum was obtained at a zero bias voltage, and the conversion efficiency was -14 dB at the microwave frequency of 18 GHz. These results strongly suggest that the fabricated thin-film Josephson junctions work well at the temperature of 77 K as detectors and mixers in the microwave regions (820 GHz).

This paper proposes an MMIC image rejection mixer and an MMIC balanced mixer employing multilayer microstrip lines and high-electron-mobility-field-effect-transistor (HEMT)s with a LUFET configuration (line-unified HEMT module). The advantage of the mixers is remarkable chip size reduction by the combination of the two technologies. The multilayer microstrip line, in which one microstrip line is placed upon another, is used for stacking passive circuits, e.g. a 90 hybrid and distributed lines, to reduce the chip-area occupied by transmission lines, and to allow flexible line allocation. The line-unified HEMT module provides all functions required for in-phase/out-of-phase power divider/combiners in HEMT electrode and unified coplanar lines configuration. A 29-32 GHz image rejection mixer and a 3-27 GHz balanced mixer are realized in only 1.6 mm 1.0 mm and 1.8 mm 1.2 mm MMIC chip size, respectively.