Yun WU Xingyu PAN Jieming YANG
Photovoltaic power is an important part of sustainable development. Accurate prediction of photovoltaic power can improve energy utilization and prevent resource waste. However, the volatility and uncertainty of photovoltaic power make power prediction difficult. Although Informer has achieved good prediction results in the field of time series prediction, it does not put forward a good solution for the volatility of series and the leakage of future information when stacking. Therefore, this paper proposes a photovoltaic power prediction model based on VMD-Informer-DCC. Firstly, Spearman’s feature selector was used to screen the sequence features. Then, the VMD layer was added to the encoder of Informer to decompose the feature sequence to reduce the volatility of the feature sequence. Finally, the dilated causal convolutional layer was used to replace the Self-attention distilling of Informer, which expanded the receptive field of Informer information extraction and ensured the causality of time series prediction. To verify the effectiveness of the model, this paper uses the dataset of a photovoltaic power plant in Jilin Province in 2021 to conduct a large number of experiments. The results show that the VMD-Informer-DCC model has high prediction accuracy and wide applicability.
Guangmiao ZENG Rongjie WANG Ran HAN
Because solar energy is intermittent and a ship's power-system load fluctuates and changes abruptly, in this work, the solar radiation parameters were adjusted according to the latitude and longitude of the ship and the change of the sea environment. An objective function was constructed that accounted for the cost and service life simultaneously to optimize the configuration of the marine diesel engine hybrid energy system. Finally, the improved artificial bee colony algorithm was used to optimize and obtain the optimal system configuration. The feasibility of the method was verified by ship navigation tests. This method exhibited better configuration performance optimization than the traditional methods.
Dai TAGUCHI Takaaki MANAKA Mitsumasa IWAMOTO Kazuko SAKUMA Kaname WATARIGUCHI Masataka KAWAHARA
Organic photoconductors (OPC) have been an important research and development topics for high quality electrophotography. By using electric field induced optical second harmonic generation (EFISHG) measurement, we can probe carrier processes in electrophotographic processes such as photo carrier generation, carrier separation, and carrier transportation for copier image production. We here selectively probe charge generation and accumulation in charge generation layer and charge transport layer in multilayer structure OPCs. We studied charge accumulation in OPC under illumination (wavelength 635nm) of double-layer-type OPC with structure of hole transport layer coated on charge generation layer. The result showed that light absorption efficiently produces free holes and electrons in the charge generation layer, followed by excessive hole accumulation at the CG/CT interface due to photo-conducting effect of CG layer. The short-wavelength irradiation at 405nm induced photovoltaic effect. These results demonstrated that the EFISHG measurement is useful to selectively probe carrier process in one layer of the multilayer OPC and to the discussion of carrier process for electrophotographic image productions.
The thin film organic photovoltaic cells (OPVs) using organic semiconductors are inferior to oxgen-resistance and water-resistance, and the OPVs have a drawback that the photoelectric conversion efficiency (η) is low. For high efficiency of the OPVs, control of bulk heterojunction (BHJ) structure in the active layer is demanded. Therefore, it is thought that we can control the BHJ structure easily if we can bring a change in the aggregated structure and the crystallinity of the BHJ structure by introducing the third component that is different from the organic semiconductor into the activity layer. In this study, we introduced peptide consisting of phenylalanine of 2 molecules into the active layer prepared by poor solvent addition effect for the organic thin film solar cells and intended to try high efficiency of the organic thin film solar cells and examined the electrochemistry characteristic of the cells.
Sirous TALEBI Ehsan ADIB Majid DELSHAD
This paper presents a high step-up DC-DC converter for low voltage sources such as solar cells, fuel cells and battery banks. A novel non isolated Zero-Voltage Switching (ZVS) interleaved DC-DC boost converter condition is introduced. In this converter, by using coupled inductor and active clamp circuit, the stored energy in leakage inductor is recycled. Furthermore, ZVS turn on condition for both main and clamp switches are provided. The active clamp circuit suppresses voltage spikes across the main switch and the voltage of clamp capacitor leads to higher voltage gain. In the proposed converter, by applying interleaved technique, input current ripple and also conduction losses are decreased. Also, with simple and effective method without applying any additional element, the input ripple due to couple inductors and active clamp circuit is cancelled to achieve a smooth low ripple input current. In addition, the applied technique in this paper leads to increasing the life cycle of circuit components which makes the proposed converter suitable for high power applications. Finally an experimental prototype of the presented converter with 40 V input voltage, 400 V output voltage and 200 W output power is implemented which verifies the theoretical analysis.
Hiroyuki NAKAMOTO Hong GAO Atsushi MURAMATSU
This paper presents a thin, compact beacon transmitter operating without needing battery replacement by using a photovoltaic (PV) film harvester. The beacon is formed of a power-control circuit (PCC) that can monitor small amounts of power from the harvester and properly control mode switching at low-power consumption. This leads to the realization of a maintenance-free beacon requiring no battery replacement. The beacon prototype is 55×20×2 mm in size and has a PV cell of 3 cm2. It allows a start-up operation from just 44-lux illuminance. The PV area required for the operation can be 1.7 times smaller than that of conventional beacons, thanks to the current saving with appropriate sequential control of the PCC. Since the beacon makes operation possible in emergency stairs, underground passages and other dark places, the application field for Internet of things (IoT) services can be expanded. Furthermore, a beacon equipped with a secondary battery (BSB: Beacon with Secondary Battery) can be configured by adding a charge-discharge power monitoring circuit. The BSB transmits an advertising packet during the daytime while charging surplus power, and works using the stored power during the night; this results in a continuous operation for one week with one transmission every 3 seconds even at 0-lux illuminance. Without developing a new radiofrequency chip or module, commercial low-power devices can be easily adjusted depending on the application by adding appropriate power-control circuits. We are convinced that this design scheme will be effective as a rapid design proposal for IoT services.
Toshifumi KOBORI Norihiko KAMATA Takeshi FUKUDA
An optical intensity distribution under light irradiation in the organic photovoltaic cell affects the absorbance of the active layer, which determines the photovoltaic performance. In this research, we evaluated the optimum thickness of the organic active layer with poly[4,8-bis(5-(2-ethylhexyl)thiophen-2-yl)benzo[1,2-b;4,5-b']dithiophene-2,6-diyl-alt-(4-(2-ethylhexyl)-3-fluorothieno[3,4-b]thiophene-)-2-carboxylate-2-6-diyl)] and [6,6]-phenyl C71-butyric acid methyl ester. The spectral response of external quantum efficiency was good agreement with the simulated optical intensity distribution within a device stack as a function of the position and the wavelength. As a result, the highest photoconversion efficiency of 10.1% was achieved for the inverted device structure.
Efficiency of the photovoltaic-assisted UHF CMOS rectifier, which is one example realization of the synergistic ambient energy harvesting concept, has been improved by symmetric PV cell structure. Balanced biasing for the n-channel and p-channel diode-connected MOSFETs realized by the symmetric PV cells effectively compensates Vths and prevents useless leakage current, resulting in the improved efficiency of the rectifier under low input power conditions. In addition, by extending the balanced biasing concept, output-voltage-boosted PV cell structure was proposed and found to be effective for further improving the efficiency of the rectifier. As a result, under a typical indoor lighting condition of 300lx, power conversion efficiency of 25.4% was achieved at -20dBm of 920MHz RF input and 47kΩ output loading conditions, being 3.6 times larger than a conventional rectifier without PV assistance.
Koji KOTANI Takumi BANDO Yuki SASAKI
A photovoltaic (PV)-assisted CMOS rectifier was developed for efficient energy harvesting from ambient radio waves as one example of the synergistic energy harvesting concept. The rectifier operates truly synergistically. A pn junction diode acting as a PV cell converts light energy to DC bias voltage, which compensates the threshold voltage (Vth) of the MOSFETs and enhances the radio frequency (RF) to DC power conversion efficiency (PCE) of the rectifier even under extremely low input power conditions. The indoor illuminance level was sufficient to generate gate bias voltages to compensate Vths. Although the same PV cell structure for biasing nMOS and pMOS transistors was used, photo-generated bias voltages were found to become unbalanced due to the two-layered pn junction structures and parasitic bipolar transistor action. Under typical indoor lighting conditions, a fabricated PV-assisted rectifier achieved a PCE greater than 20% at an RF input power of -20dBm, a frequency of 920MHz, and an output load of 47kΩ. This PCE value is twice the value obtained by a conventional rectifier without PV assistance. In addition, it was experimentally revealed that if symmetric biasing voltages for nMOS and pMOS transistors were available, the PCE would increase even further.
Takuya HORIOKA Zhaokui WANG Shigeki NAKA Hiroyuki OKADA
We have optimized and evaluated organic thin-film solar cell devices with a structure of graded junction. The graded junction consisting of donor and accepter materials was fabricated by varying the deposition rates of both materials with a continuous grading, using two evaporation sources of cupper phthalocyanine and fullerene as p- and n-type materials, respectively. By evaluating device characteristics, optimized device structure ITO/CuPc (10 nm)/graded layer (35 nm)/C60 (15 nm)/BCP (10 nm)/Ag (100 nm) with an efficiency of 1.36% was obtained. In the structure, short-circuit current density was the largest and existence of larger voltage dependence in current density was observed. In addition, we have measured temperature dependences of current density versus voltage characteristics in the graded organic solar cell under illumination. The carrier extraction was enhanced by changing voltage possibly due to the internal electric field of the graded junction.
This paper introduces the basics of energy harvesters and demonstrates two specific vibratory-type energy harvesters developed at the University of Hyogo. The fabrication and evaluation results of the vibratory-type energy harvesters, which employ electrostatic and electromagnetic mechanisms, are described. The aim of developing these devices is to realize a power source for an autonomous human monitoring system. The results of harvesting from actual human activities obtained using a data logger are also described. Moreover, challenges in the power management of electronic circuitry used for energy harvesting are briefly discussed.
Takeshi FUKUDA Kenji TAKAGI Norihiko KAMATA Jungmyoung JU Yutaka YAMAGATA
We demonstrated the reduced surface roughness of poly (3-hexylthiophene) (P3HT):(6,6)-phenyl-C61-butyric acid methyl ester (PCBM) thin films with different ratios fabricated by the electrospray deposition (ESD) method. Aggregated structures were observed at the lower voltage, and the uniformity became bad at the higher voltage. Anyway, the minimum root mean square (RMS) roughness was 1.46 nm by optimizing the applied voltage.
Eiji ITOH Yuji HIGUCHI Daisuke FURUHATA
We investigated the photovoltaic properties of multilayered devices consisting of ITO/oxide/Tetraphenyl porphyrin (H2TPP)/Fullerene (C60)/Bathocuproine (BCP)/Al structures. The VOC markedly increases with the insertion of NiO and MoO3 hole collection layers. However, the "kink" behaviors and temperature dependent properties are observed for the devices with and without MoO3 especially for the thick H2TPP film. We demonstrated the analysis of the photovoltaic properties using the Poole-Frenkel and Schottky models based on the dielectric behaviors of porphyrin and MoO3 layers.
Youn-Ok CHOI Zheng-Guo PIAO Geum-Bae CHO
This study examined the performance improvement of a photovoltaic (PV) array and inverter as well as their design, construction, and post-operation and management, which will become the key elements in future PV systems. In addition, it evaluated the performance characteristics of a 50 kW grid-connection PV system in Korea. According to the result of the evaluation, the PV array showed approximately 10% efficiency. The inverter was indicated to operate at > 90% efficiency regularly at > 400 W/m2 irradiation. The capture losses (Lc), system losses (Ls) and performance ratio were approximately 0.9 h/d, 0.3 h/d, and > 70%, respectively, indicating that the system was operating stably. In addition, while the Ls decreased rapidly due to the efficiency of the inverter, the performance ratio decreased markedly with increasing Lc due to the increase in temperature when the reference yield was > 5.0 h/d.
Chang Wook AHN Ju Yeop CHOI Dong-Ha LEE Jinung AN
This paper presents an adaptive maximum power point tracking (MPPT) algorithm. The aim is to dynamically adjust the step length for updating duty ratio (or operating voltage) so as to make full utilization of the output power of photovoltaic (PV) systems, even under the rapidly changing atmospheric conditions. To this end, the average slope in terms of voltage and power is exploited for reducing the harmful effect of noise and error (incurred in measurement or quantization) on the slope. Also, a statistical decision-making scheme is employed for reliably deciding the time instant at which atmospheric conditions actually change. Empirical study has adduced grounds for its dominance over existing references.
Tetsuya TAIMA Toshihiro YAMANARI Kohjiro HARA Kazuhiro SAITO
We succeeded to fabricate p-n heterojunction and bulkheterojunction small-molecular-weight organic thin-film solar cells by combination of dry (p-type = zinc phthalocyanine, n-type = fullerene) and wet (p-type = tetra-tert-butyl zinc phthalocyanine, n-type = [6,6]-phenyl-C61-buteric acid methyl ester) processes. Relationship between morphologies of semiconducting layers and photovoltaic properties was investigated. The p-n heterojunction organic thin-film solar cells based on dry process, where surface roughness was approximately 2 nm, showed the highest power conversion efficiency of 1.3% in this paper.
Tetsuya TAIMA Masayuki CHIKAMATSU Yuji YOSHIDA Kazuhiro SAITO Kiyoshi YASE
We fabricated organic p-n heterojunction, p-i-n heterojunction and all-i-layer photovoltaic cells of a zinc phthalocyanine (ZnPc)/1:1 codeposition (ZnPc:C60)/C60 structure with Al cathode. We investigated the effects of the device structure and the cathode material on the photovoltaic properties. The thickness of the i-layer was changed as 0 nm (= p-n heterojunction), 10 nm (= p-i-n heterojunction) or 50 nm (= all-i-layer) with the total thickness of 50 nm. We also changed cathode materials from Al to low-workfunction Mg:Ag electrode. Photovoltaic properties, i.e., short-circuit current density, fill factor and power conversion efficiency, were strongly influenced by the device structure and cathode material. Finally, the power conversion efficiency showed a maximum (1.5%) with the p-i-n structure and a Mg:Ag cathode under Air Mass 1.5 global solar conditions.
Satoshi TANEZAKI Toshio MATSUSHIMA Seiichi MUROYAMA
We describe a simulation method and design for a stand-alone hybrid power supply system composed of a wind turbine generator and photovoltaic modules. The system has been developed to supply power for telecommunications equipment in areas with no commercial power sources. We also report a comparison of the simulation results with actual measured data. The results show that the hybrid system can function effectively as a power supply for telecommunications equipment.
Yousuke NOZAKI Kazuya AKIYAMA Toshiaki YACHI Hiroshi KAWAGUCHI Kosuke KUROKAWA
Stand-alone photovoltaic (PV) power systems are potential power sources for telecommunications equipment especially equipment installed outdoors. To be practical, they must have a high conversion efficiency and a long lifetime. We have proposed a stand-alone photovoltaic power system that uses electric double-layer capacitors (EDLCs) and lead acid batteries as power storage devices. This system smooths out the fluctuations in power generated by the PV array by using the EDLC's charge-and-discharge power; this reduces the number of battery charge-and-discharge cycles. We simulated the system's operating characteristics and evaluated the photovoltaic array mismatching loss, system conversion loss, battery contribution factor, averaged battery state-of-charging, and maximum depth-of-discharging. The results show that the system is effective at reducing the mismatching loss and battery contribution factor, so the system efficiency is expected to be improved by using high conversion efficiency DC-DC converters. Moreover the system can maintain the averaged battery state-of-charging during operation. This indicates that smaller batteries can be used. The maximum depth-of-discharging can be kept lower than in the conventional system. Consequently, the proposed system should have a longer battery lifetime.
Mitsuyoshi ONODA Kazuya TADA Katsumi YOSHINO
Unique characteristics such as quenching of photoluminescence and improvement of photovoltaic effect were observed in acceptor polymer, (cyano-substituted poly (p-phenylene vinylene)), CN-PPV/donor polymer (poly(3-hexylthiophene), P3HT composites. By taking account of the difference in electronic energy states of both CN-PPV and P3HT, these characteristics are interpreted in terms of photoinduced charge transfer between CN-PPV and P3HT and formation of fractal network.