The adiabatic quantum flux parametron (AQFP) is an energy-efficient, high-speed superconducting logic device. To observe the tiny output currents from the AQFP in experiments, high-speed voltage drivers are indispensable. In the present study, we develop a compact voltage driver for AQFP logic based on a Josephson latching driver (JLD), which has been used as a high-speed driver for rapid single-flux-quantum (RSFQ) logic. In the JLD-based voltage driver, the signal currents of AQFP gates are converted into gap-voltage-level signals via an AQFP/RSFQ interface and a four-junction logic gate. Furthermore, this voltage driver includes only 15 Josephson junctions, which is much fewer than in the case for the previously designed driver based on dc superconducting quantum interference devices (60 junctions). In measurement, we successfully operate the JLD-based voltage driver up to 4 GHz. We also evaluate the bit error rate (BER) of the driver and find that the BER is 7.92×10-10 and 2.67×10-3 at 1GHz and 4GHz, respectively.

We experimentally evaluated random number sequences generated by a superconducting hardware random number generator composed of a Josephson-junction oscillator, a rapid-single-flux-quantum (RSFQ) toggle flip-flop (TFF), and an RSFQ AND gate. Test circuits were fabricated using a 10 kA/cm2 Nb/AlOx/Nb integration process. Measurements were conducted in a liquid helium bath. The random numbers were generated for a trigger frequency of 500 kHz under the oscillating Josephson-junction at 29 GHz. 26 random number sequences of 20 kb length were evaluated for bias voltages between 2.0 and 2.7 mV. The NIST FIPS PUBS 140-2 tests were used for the evaluation. 100% pass rates were confirmed at the bias voltages of 2.5 and 2.6 mV. We found that the Monobit test limited the pass rates. As numerical simulations suggested, a detailed evaluation for the probability of obtaining “1” demonstrated the monotonical dependence on the bias voltage.

We have studied on thermally assisted nano-structured transistors made of superconductor ultra-thin films. These transistors potentially work as interface devices for Josephson-CMOS (complementary metal oxide semiconductor) hybrid memory systems, because they can generate a high output voltage of sub-V enough to drive a CMOS transistor. In addition, our superconductor transistors are formed with very fine lines down to several tens of nm in widths, leading to very small foot print enabling us to make large capacity hybrid memories. Our superconductor transistors are made with niobium titanium nitride (NbTiN) thin films deposited on thermally-oxidized silicon substrates, on which other superconductor circuits or semiconductor circuits can be formed. The NbTiN thickness dependence of the critical temperature and of resistivity suggest thermally activated vortex or anti-vortex behavior in pseudo-two-dimensional superconducting films plays an important role for the operating principle of the transistors. To show the potential that the transistors can drive MOS transistors, we analyzed the driving ability of the superconductor transistors with HSPICE simulation. We also showed the turn-on behavior of a MOS transistor used for readout of a CMOS memory cell experimentally. These results showed the high potential of superconductor transistors for Josephson-CMOS hybrid memories.

We present circuit implementations for computing exponentials and logarithms suitable for rapid single-flux-quantum (RSFQ) logic. We propose hardware algorithms based on the sequential table-lookup (STL) method using the radix-2 signed-digit representation that achieve high-throughput, digit-serial calculations. The circuits are implemented by processing elements formed in systolic-array-like, regularly-aligned pipeline structures. The processing elements are composed of adders, shifters, and readouts of precomputed constants. The iterative calculations are fully overlapped, and throughputs approach the maximum throughput of serial processing. The circuit size for calculating significand parts is estimated to be approximately 5-10 times larger than that of a bit-serial floating-point adder or multiplier.

We report the successful operation of a low-power arithmetic logic unit (ALU) based on a low-voltage rapid single-flux-quantum (LV-RSFQ) logic circuit, whereby a dc bias current is fed to circuits from lowered constant-voltage sources through small resistors. Both the static and dynamic energy consumptions are reduced because of the reduction in the amplitudes of voltage pulses across the Josephson junctions, with a trade-off of slightly slower switching speeds. The designed bias voltage was set to 0.25mV, which is one-tenth that of our standard RSFQ circuit design. We investigated several issues related to such low-voltage operation, including margins and timing design. To achieve successful operation, we tuned the circuit parameters in the logic gate design and carefully controlled the timing by considering the interference of pulse signals. We show test results for the low-voltage ALU in on-chip high-speed testing. The circuit was fabricated using the AIST Nb/AlOx/Nb Advanced Process with a critical current density of 10kA/cm2. We verified that arithmetic and logical operations were correctly implemented and obtained dc bias margins of 18% at a target clock frequency of 20GHz and achieved a maximum clock frequency of 28GHz with a power consumption of 28µW. These experimental results indicate energy efficiency of 3.6 times that of the standard RSFQ circuit design.