This paper presents a high power efficient pulse VCO with tail-filter for the chip-scale atomic clock (CSAC) application. The stringent power and clock stability specifications of next-generation CSAC demand a VCO with ultra-low power consumption and low phase noise. The proposed VCO architecture aims for the high power efficiency, while further reducing the phase noise using tail filtering technique. The VCO has been implemented in a standard 45nm SOI technology for validation. At an oscillation frequency of 5.0GHz, the proposed VCO achieves a phase noise of -120dBc/Hz at 1MHz offset, while consuming 1.35mW. This translates into an FoM of -191dBc/Hz.

This paper presents a high jitter performance injection-locked clock multiplier (ILCM) using an ultra-low power (ULP) voltage-controlled oscillator (VCO) for IoT application in 65-nm CMOS. The proposed transformer-based VCO achieves low flicker noise corner and sub-100µW power consumption. Double cross-coupled NMOS transistors sharing the same current provide high transconductance. The network using high-Q factor transformer (TF) provides a large tank impedance to minimize the current requirement. Thanks to the low current bias with a small conduction angle in the ULP VCO design, the proposed TF-based VCO's flicker noise can be suppressed, and a good PN can be achieved in flicker region (1/f3) with sub-100µW power consumption. Thus, a high figure-of-merit (FoM) can be obtained at both 100kHz and 1MHz without additional inductor. The proposed VCO achieves phase noise of -94.5/-115.3dBc/Hz at 100kHz/1MHz frequency offset with a 97µW power consumption, which corresponds to a -193/-194dBc/Hz VCO FoM at 2.62GHz oscillation frequency. The measurement results show that the 1/f3 corner is below 60kHz over the tuning range from 2.57GHz to 3.40GHz. Thanks to the proposed low power VCO, the total ILCM achieves 78 fs RMS jitter while using a high reference clock. A 960 fs RMS jitter can be achieved with a 40MHz common reference and 107µW corresponding power.

Supporting quality-of-service (QoS) of multimedia communications over IEEE 802.11 based ad hoc networks is a challenging task. This paper develops a simple 3-D Markov chain model for queuing analysis of IEEE 802.11 MAC layer. The model is applied for performance analysis of voice communications over IEEE 802.11 single-hop ad hoc networks. By using the model, we finish the performance optimization of IEEE MAC layer and obtain the maximum number of voice calls in IEEE 802.11 ad hoc networks as well as the statistical performance bounds. Furthermore, we design a fully distributed call admission control (CAC) algorithm which can provide strict statistical QoS guarantee for voice communications over IEEE 802.11 ad hoc networks. Extensive simulations indicate the accuracy of the analytical model and the CAC scheme.

This paper presents a fully integrated yet compact receiver front-end for Sub-GHz applications such as Internet-of-Things (IoT). The low noise amplifier (LNA) matching network leverages an inductance boosting technique. A relatively small on-chip inductor with a compact area achieves impedance matching in such a low frequency. Moreover, a passive-mixer-first mode bypasses the LNA to extend the receiver dynamic-range. The passive mixer provides matching to the 50Ω antenna interface to eliminate the need for additional passive components. Therefore, the receiver can be fully-integrated without any off-chip matching components. The flipped-voltage-follower (FVF) cell is adopted in the low pass filter (LPF) and the variable gain amplifier (VGA) for its high linearity and low power consumption. Fabricated in 65nm LP CMOS process, the proposed receiver front-end occupies 0.37mm2 core area, with a tolerable input power ranging from -91.5dBm to -1dBm for 500kbps GMSK signal at 924MHz frequency. The power consumption is 1mW power under a 1.2V supply.

An energy efficient modulator for an ultra-low-power (ULP) 60-GHz IEEE transmitter is presented in this paper. The modulator consists of a differential duobinary coder and a semi-digital finite-impulse-response (FIR) pulse-shaping filter. By virtue of differential duobinary coding and pulse shaping, the transceiver successfully solves the adjacent-channel-power-ratio (ACPR) issue of conventional on-off-keying (OOK) transceivers. The proposed differential duobinary code adopts an over-sampling precoder, which relaxes timing requirement and reduces power consumption. The semi-digital FIR eliminates the power hungry digital multipliers and accumulators, and improves the power efficiency through optimization of filter parameters. Fabricated in a 65nm CMOS process, this modulator occupies a core area of 0.12mm2. With a throughput of 1.7Gbps/2.6Gbps, power consumption of modulator is 24.3mW/42.8mW respectively, while satisfying the IEEE 802.11ad spectrum mask.

This paper presents a miniaturized transformer-based ultra-low-power (ULP) LC-VCO with embedded supply pushing reduction techniques for IoT applications in 65-nm CMOS process. To reduce the on-chip area, a compact transformer patterned ground shield (PGS) is implemented. The transistors with switchable capacitor banks and associated components are placed underneath the transformer, which further shrinking the on-chip area. To lower the power consumption of VCO, a gm-stacked LC-VCO using the transformer embedded with PGS is proposed. The transformer is designed to provide large inductance to obtain a robust start-up within limited power consumption. Avoiding implementing an off/on-chip Low-dropout regulator (LDO) which requires additional voltage headroom, a low-power supply pushing reduction feedback loop is integrated to mitigate the current variation and thus the oscillation amplitude and frequency can be stabilized. The proposed ULP TF-based LC-VCO achieves phase noise of -114.8dBc/Hz at 1MHz frequency offset and 16kHz flicker corner with a 103µW power consumption at 2.6GHz oscillation frequency, which corresponds to a -193dBc/Hz VCO figure-of-merit (FoM) and only occupies 0.12mm2 on-chip area. The supply pushing is reduced to 2MHz/V resulting in a -50dBc spur, while 5MHz sinusoidal ripples with 50mVPP are added on the DC supply.