A 60 GHz direct conversion transceiver which employs amplitude/phase imbalance cancellation technique is newly proposed. By using the proposed technique, the receive path of the transceiver achieves less than 0.2 dB of amplitude error and less than 3 of phase error at 60 GHz bands over a 10 GHz bandwidth, which relaxes the design accuracy required for baluns used in the transceiver. It also employs a simple and fast calibration algorithm to adjust the locking range of the divide-by-3 injection locked divider in the phase locked loop. Fabricated in 90 nm CMOS technology, the transceiver achieves a low power consumption of 230 mW in transmit mode and 173 mW in receive mode. The output spectrum of 1.76 Gsps π/2-BPSK/QPSK modulation shows the excellent distortion and spurious suppression that meet the IEEE802.11ad draft standard.

In this paper, we present the roles played by millimeter-waves in the realization of an Internet of Things (IoT) society. Millimeter-waves are becoming essential frequency resources, enabling ultra-high-speed wireless networks supporting massive data traffic and high-resolution sensor devices. Multiple antenna technologies such as phased arrays, sector antennas, and MIMO signal processing are key technologies for putting these into practical use. In this paper, various examples of integration of multi-antenna systems are shown, as well as demonstration on 60GHz-band millimeter-wave wireless access and 79GHz-band high-resolution radar. We also propose applications to ITS for an IoT society, combining millimeter-wave wireless access and radar sensors, and discuss technical issues to be solved in the future.

Triggered by the explosion of mobile traffic, 5G (5th Generation) cellular network requires evolution to increase the system rate 1000 times higher than the current systems in 10 years. Motivated by this common problem, there are several studies to integrate mm-wave access into current cellular networks as multi-band heterogeneous networks to exploit the ultra-wideband aspect of the mm-wave band. The authors of this paper have proposed comprehensive architecture of cellular networks with mm-wave access, where mm-wave small cell basestations and a conventional macro basestation are connected to Centralized-RAN (C-RAN) to effectively operate the system by enabling power efficient seamless handover as well as centralized resource control including dynamic cell structuring to match the limited coverage of mm-wave access with high traffic user locations via user-plane/control-plane splitting. In this paper, to prove the effectiveness of the proposed 5G cellular networks with mm-wave access, system level simulation is conducted by introducing an expected future traffic model, a measurement based mm-wave propagation model, and a centralized cell association algorithm by exploiting the C-RAN architecture. The numerical results show the effectiveness of the proposed network to realize 1000 times higher system rate than the current network in 10 years which is not achieved by the small cells using commonly considered 3.5GHz band. Furthermore, the paper also gives latest status of mm-wave devices and regulations to show the feasibility of using mm-wave in the 5G systems.

This paper presents a 60 GHz analog/digital beamforming receiver that effectively suppresses interference signals, targeting the IEEE 802.11ad/WiGig standard. Combining two-stream analog frontends with interference rejection digital signal processing, the analog beamforming steers the antenna beam to the desired direction while the digital beamforming provides gain suppression in the interference direction. A prototype has been built with 40 nm CMOS analog frontends as well as offline baseband digital signal processing. Measurements show a 3.1 dB EVM advantage over conventional two-stream diversity during a packet collision situation.

This paper presents a programmable wideband low pass filter (LPF) with Continuous-Time (CT)/Discrete-Time (DT) hybrid architecture. Unlike the conventional DT LPF, the proposed LPF eliminates sample & hold circuits, enabling to expand available bandwidth. The transfer function and the influence of the circuit imperfection are derived from CT/DT hybrid analysis. A prototype has been fabricated in 40 nm CMOS process. The proposed LPF achieves 2.5 GHz bandwidth by wideband equalization, which offers capacitance ratio (Cratio) and clock frequency (fCK) programmability. The proposed LPF occupies only 0.048 mm2 of active area.

The Direct Sampling Mixer (DSM) with a complex coefficient transfer function is demonstrated. The operation theory and the detail design methodology are discussed for the high order complex DSM, which can achieve large image rejection ratio by introducing the attenuation pole at the image frequency band. The proposed architecture was fabricated in a 65 nm CMOS process. The measured results agree well with the theoretical calculation, which proves the validity of the proposed architecture and the design methodology. By using the proposed design method, it will be possible for circuit designers to design the DSM with large image rejection ratio without repeated lengthy simulations.

This paper presents an automatic gain control (AGC) system suitable for 60GHz direct conversion receivers. By using a two step gain control algorithm with high-pass filter cutoff frequency switching, the proposed AGC system realizes fast settling time and wide dynamic range simultaneously. The paper also discusses wide-bandwidth variable gain amplifier (VGA) design. By introducing digitally-controlled resistors and gain flattening capacitors, the proposed VGA realizes wide gain range while compensating gain variations due to parasitic capacitance of MOS switches. The AGC system is implemented in a transceiver chipset where RFIC and BBIC are fabricated in 90nm CMOS and 40nm CMOS respectively. The measurement shows excellent dynamic range of 47dB with +/-1dB gain accuracy within 1µs settling time, which satisfies the stringent requirements of the IEEE802.11ad standard.

Wireless engineers and business planners commonly raise the question on where, when, and how millimeter-wave (mmWave) will be used in 5G and beyond. Since the next generation network is not just a new radio access standard, but also an integration of networks for vertical markets with diverse applications, answers to the question depend on scenarios and use cases to be deployed. This paper gives four 5G mmWave deployment examples and describes in chronological order the scenarios and use cases of their probable deployment, including expected system architectures and hardware prototypes. The first example is a 28 GHz outdoor backhauling for fixed wireless access and moving hotspots, which will be demonstrated at the PyeongChang Winter Olympic Games in 2018. The second deployment example is a 60 GHz unlicensed indoor access system at the Tokyo-Narita airport, which is combined with Mobile Edge Computing (MEC) to enable ultra-high speed content download with low latency. The third example is mmWave mesh network to be used as a micro Radio Access Network (µ-RAN), for cost-effective backhauling of small-cell Base Stations (BSs) in dense urban scenarios. The last example is mmWave based Vehicular-to-Vehicular (V2V) and Vehicular-to-Everything (V2X) communications system, which enables automated driving by exchanging High Definition (HD) dynamic map information between cars and Roadside Units (RSUs). For 5G and beyond, mmWave and MEC will play important roles for a diverse set of applications that require both ultra-high data rate and low latency communications.

Millimeter-wave (mmw) frequency bands, especially 60GHz unlicensed band, are considered as a promising solution for gigabit short range wireless communication systems. IEEE standard 802.11ad, also known as WiGig, is standardized for the usage of the 60GHz unlicensed band for wireless local area networks (WLANs). By using this mmw WLAN, multi-Gbps rate can be achieved to support bandwidth-intensive multimedia applications. Exhaustive search along with beamforming (BF) is usually used to overcome 60GHz channel propagation loss and accomplish data transmissions in such mmw WLANs. Because of its short range transmission with a high susceptibility to path blocking, multiple number of mmw access points (APs) should be used to fully cover a typical target environment for future high capacity multi-Gbps WLANs. Therefore, coordination among mmw APs is highly needed to overcome packet collisions resulting from un-coordinated exhaustive search BF and to increase total capacity of mmw WLANs. In this paper, we firstly give the current status of mmw WLANs with our developed WiGig AP prototype. Then, we highlight the great need for coordinated transmissions among mmw APs as a key enabler for future high capacity mmw WLANs. Two different types of coordinated mmw WLAN architecture are introduced. One is distributed antenna type architecture to realize centralized coordination, while the other is autonomous coordination with the assistance of legacy Wi-Fi signaling. Moreover, two heterogeneous network (HetNet) architectures are also introduced to efficiently extend the coordinated mmw WLANs to be used for future 5th Generation (5G) cellular networks.

This paper presents the design and experimental evaluation of 60GHz small cell radio access based on IEEE 802.11ad/WiGig. The access point (AP) prototype used combines three RF modules with beamforming technology to provide 360° area coverage. In order to compensate for limited communication distance, multiple APs are employed to achieve wide area coverage. A handover algorithm suitable for IEEE 802.11ad/WiGig is employed to achieve flexible control of the cell coverage of each AP. As a proof of concept, a prototype system is set up at Narita International Airport and the capability of multiuser Gb/s wireless access is successfully demonstrated. In addition, the system behavior under stringent conditions is evaluated by load testing and throughput degradation due to co-channel and inter-channel interference is investigated.

This paper presents a wideband digital predistortion (DPD) architecture suitable for wideband wireless systems, such as IEEE 802.11ad/WiGig, where low oversampling ratio of the digital-to-analog converter (DAC) is a bottleneck for available linearization bandwidth. In order to overcome the bandwidth limitation in the conventional DPD, the proposed DPD introduces a complex coefficient filter in the DPD signal processing, which enables it to achieve asymmetric linearization. This approach effectively suppresses one side of adjacent channel leakages with twice the bandwidth as compared to the conventional DPD. The concept is verified through system simulation and measurements. Using a scaled model of a 2 GHz RF carrier frequency, the measurement shows a 4.2 dB advantage over the conventional DPD in terms of adjacent channel leakage.

This paper demonstrates 300GHz terahertz wireless communication using CMOS transmitter (TX) and receiver (RX) modules targeting sixth-generation (6G). To extend communication distance, CMOS modules with WR-3.4 waveguide interface and a high-gain antenna of 40dBi Cassegrain antenna are designed, achieving 36Gbps throughput at a 1m communication distance. Besides, in order to support orthogonal frequency-division multiplexing (OFDM), a self-heterodyne architecture is introduced, which effectively cancels the phase noise in multi-carrier modulation. As a proof-of-concept (PoC), the paper successfully demonstrates real-time video transfer at a 10m communication distance using fifth-generation (5G) based OFDM at the 300GHz frequency band.