We have developed a novel array configuration based on the combination of sum and difference co-arrays. There have been many studies on array antenna configurations that enhance the degree of freedom (DOF) of an array, but the maximum DOF of the difference co-array configuration is often limited. With our proposed array configuration, called “sum and difference composite co-array”, we aim to further enhance the DOF by combining the concept of sum co-array and difference co-array. The performance of the proposed array configuration is evaluated through computer simulated beamforming*.

The symbol flipping decoding algorithms based on prediction (SFDP) for non-binary LDPC codes perform well in terms of error performances but converge slowly when compared to other symbol flipping decoding algorithms. In order to improve the convergence rate, we design new flipping rules with two phases for the SFDP algorithms. In the first phase, two or more symbols are flipped at each iteration to allow a quick increase of the objective function. While in the second phase, only one symbol is flipped to avoid the oscillation of the decoder when the objective function is close to its maximum. Simulation results show that the SFDP algorithms with the proposed flipping rules can reduce the average number of iterations significantly, whereas having similar performances when compared to the original SFDP algorithms.

A physical-layer network coding (PNC) scheme is developed using serially concatenated continuous phase modulation (SCCPM) with symbol interleavers in a two-way relay channel (TWRC), i.e., SCCPM-PNC. The decoding structure of the relay is designed and the corresponding soft input soft output (SISO) iterative decoding algorithm is discussed. Simulation results show that the proposed SCCPM-PNC scheme performs good performance in bit error rate (BER) and considerable improvements can be achieved by increasing the interleaver size and number of iterations.

Controller area network (CAN) has been widely adopted as an in-vehicle communications standard. CAN with flexible data-rate (CAN FD) is defined in the ISO standards to achieve higher data rates than the legacy CAN. A number of CAN nodes can be connected by a single transmission medium, i.e. CAN enables us to constitute cost-effective bus-topology networks. CAN puts carrier sense multiple access with collision resolution (CSMA/CR) into practice by using bit-wise arbitration based on wired logical AND in the physical layer. The most prioritized message is delivered without interruption if two or more CAN nodes transmit messages at the same time due to the bit-wise arbitration. However, the scalability of CAN networks suffers from ringing caused by the signaling mechanism establishing the wired logical AND. We need to reduce networking material in a car in order to reduce the car weight, save the fuel and the cost, and develop a sustainable society by establishing more scalable CAN networks. In this paper, we show a reduced wiring technology for CAN to enhance the network scalability and the cost efficiency.

Body bias generators are useful circuits that can reduce variability and power dissipation in LSI circuits. However, the amplifier implemented into the body bias generator is difficult to design because of its complexity. To overcome the difficulty, this paper proposes a clearer cell-based design method of the amplifier than the existing cell-based design methods. The proposed method is based on a simple analytical model, which enables to easily design the amplifiers under various operating conditions. First, we introduce a small signal equivalent circuit of two-stage amplifiers by which we approximate a three-stage amplifier, and introduce a method for determining its design parameters based on the analytical model. Second, we propose a method of tuning parameters such as cell-based phase compensation elements and drive-strength of the output stage. Finally, based on the test chip measurement, we show the advantage of the body bias generator we designed in a cell-based flow over existing designs.

In this paper, we propose a novel group formation scheme which is integrated with an EMGC protocol in order to cope with dynamic group change. It uses a link expiration time and residual energy to form a stable link in a group. It also has a group merging procedure to decrease the number of groups. Furthermore, we develop two additional functions for the protocol, i.e., GL rotation and a stay connection procedure to diminish energy consumption of sensor nodes in the network. Simulation results show that the proposed protocol outperforms MBC, EMGCwoh, and EMGC protocols in terms of data delivery, network lifetime, and energy dissipation per round with various group change probabilities and percentages of groups.

This paper discusses non-ideal issues in a fully passive noise shaping successive approximation register analog-to-digital converter. The fully passive noise shaping techniques are realized by switches and capacitors without operational amplifiers to be scalable and power efficient. However, some non-ideal issues, such as parasitic capacitance, comparator noise, thermal noise, will affect the performance of the noise shaping and then degrade the final achievable resolution. This paper analyzes the effects of the main non-ideal issues and provides the design reference for fully passive noise shaping techniques. The analysis is based on 2nd order fully passive noise shaping SAR ADC with an 8-bit architecture and an OSR of 4.

Compressed sensing is an effective compression algorithm. It is widely used to measure signals in distributed sensor networks (DSNs). Considering the limited resources of DSNs, the measurement matrices used in DSNs must be simple. In this paper, we construct a deterministic measurement matrix based on Gordon-Mills-Welch (GMW) sequence. The column vectors of the proposed measurement matrix are generated by cyclically shifting a GMW sequence. Compared with some state-of-the-art measurement matrices, the proposed measurement matrix has relative lower computational complexity and needs less storage space. It is suitable for resource-constrained DSNs. Moreover, because the proposed measurement matrix can be realized by using simple shift register, it is more practical. The simulation result shows that, in terms of recovery quality, the proposed measurement matrix performs better than some state-of-the-art measurement matrices.

This paper reviews access system standardization activities and related technologies from the viewpoints of optical-based PON access, mobile access systems including LPWAN, and access network virtualization. Future study issues for the next access systems are also presented.

By incorporating cloud computing capabilities to provide radio access functionalities, Cloud Radio Access Networks (CRANs) are considered to be a key enabling technology of future 5G and beyond communication systems. In CRANs, centralized radio resource allocation optimization is performed over a large number of small cells served by simple access points, the Remote Radio Heads (RRHs). However, the fronthaul links connecting each RRH to the cloud introduce delays and entail imperfect Channel State Information (CSI) knowledge at the cloud processors. In order to satisfy the stringent latency requirements envisioned for 5G applications, the concept of Fog Radio Access Networks (FogRANs) has recently emerged for providing cloud computing at the edge of the network. Although FogRAN may alleviate the latency and CSI quality issues of CRAN, its distributed nature degrades network interference mitigation and global system performance. Therefore, we investigate the design of tailored user pre-scheduling and beamforming for FogRANs. In particular, we propose a hybrid algorithm that exploits both the centralized feature of the cloud for globally-optimized pre-scheduling using imperfect global CSIs, and the distributed nature of FogRAN for accurate beamforming with high quality local CSIs. The centralized phase enables the interference patterns over the global network to be considered, while the distributed phase allows for latency reduction, in line with the requirements of FogRAN applications. Simulation results show that our proposed algorithm outperforms the baseline algorithm under imperfect CSIs, jointly in terms of throughput, energy efficiency, as well as delay.

We have investigated post-metallization annealing (PMA) utilizing TiN gate electrode on the thin ferroelectric undoped HfO2 directly deposited on p-Si(100) by RF magnetron sputtering. By post-deposition annealing (PDA) process at 600°C/30 s in N2, the memory window (MW) in the C-V characteristics was observed in the Al/HfO2/p-Si(100) diodes with 15 to 24-nm-thick HfO2. However, it was not obtained when the thickness of HfO2 was 10 nm. On the other hand, the MW was observed for Pt/TiN/HfO2 (10 nm)/p-Si(100) diodes utilizing PMA process at 600°C/30 s. The MW was 0.5 V when the bias voltage was applied from -3 to 3 V.

Wireless communication security has been increasingly important nowadays. Directional modulation (DM) is seen as a promising wireless physical layer security technology. Traditional DM is a transmit-side technology that projects digitally modulated information signals in the desired directions (or at the desired locations) while simultaneously distorting the constellation formats of the same signals in other directions (or at all other locations). However, these directly exposed digitally modulated information signals are easily intercepted by eavesdroppers along the desired directions (or around the desired locations). A new DM scheme for secure point-to-multipoint communication based on the spread spectrum assisted orthogonal frequency diverse array (short for SS-OFDA-M-DM) is proposed in this paper. It can achieve point-to-multipoint secure communication for multiple cooperative receivers at different locations. In the proposed SS-OFDA-M-DM scheme, only cooperative users that use specific DM receivers with right spread spectrum parameters can retrieve right symbols. Eavesdroppers without knowledge of spread spectrum parameters cannot intercept useful signals directly at the desired locations. Moreover, they cannot receive normal symbols at other locations either even if the right spread spectrum parameters are known. Numerical simulation results verify the validity of our proposed scheme.

We numerically demonstrate a possibility on-off keying (OOK) type of modulation over tens gigabits per second for sub-terahertz radiation in our proposed wireless transmitter device structure towards radio over fiber (RoF) technology. The integrated device consists of an InP-based compound semiconductor resonant tunneling diode (RTD) adjacent to an InP-based photo diode (PD), a self-complementary type of bow-tie antenna (BTA), external microstrip lines. These integration structures are carefully designed to obtain robust relaxation oscillation (RO) due to the negative differential conductance (NDC) characteristic of the RTD and the nonlinearity of the NDC. Moreover, the device is designed to exhibit OOK modulation of RO due to photo current from the PD inject into the RTD. Electromagnetic simulations and nonlinear equivalent circuit model of the whole device structure are established to perform large signal analysis numerically with considerations of previously measured characteristics of the triple-barrier RTD.

In this paper, we have investigated the etching selectivity of HfN encapsulating layer for high quality PtHf-alloy silicide (PtHfSi) formation with low contact resistivity on Si(100). The HfN(10 nm)/PtHf(20 nm)/p-Si(100) stacked layer was in-situ deposited by RF-magnetron sputtering at room temperature. Then, silicidation was carried out at 500°C/20 min in N2/4.9%H2 ambient. Next, the HfN encapsulating layer was etched for 1-10 min by buffered-HF (BHF) followed by the unreacted PtHf metal etching. We have found that the etching duration of the 10-nm-thick HfN encapsulating layer should be shorter than 6 min to maintain the PtHfSi crystallinity. This is probably because the PtHf-alloy silicide was gradually etched by BHF especially for the Hf atoms after the HfN was completely removed. The optimized etching process realized the ultra-low contact resistivity of PtHfSi to p+/n-Si(100) and n+/p-Si(100) such as 9.4×10-9Ωcm2 and 4.8×10-9Ωcm2, respectively, utilizing the dopant segregation process. The control of etching duration of HfN encapsulating layer is important to realize the high quality PtHfSi formation with low contact resistivity.

This paper proposes an improved closed-form method for moving source localization using time difference of arrival (TDOA), frequency difference of arrival (FDOA) and differential Doppler rate measurements. After linearizing the measurement equations by introducing three additional parameters, a rough estimate is obtained by using the weighted least-square (WLS) estimator. To further refine the estimate, the relationship between additional parameters and source location is utilized. The proposed method gives a final closed-form solution without iteration or the extra mathematics operations used in existing methods by employing the basic idea of WLS processing. Numerical examples show that the proposed method exhibits better robustness and performance compared with several existing methods.

In this paper, we propose a new technique for the transient scattering problem of periodically arrayed dispersion media for the TE case by using a combination of the Fourier series expansion method (FSEM) and the fast inversion Laplace transform (FILT) method, and analyze the pulse response for various widths of the dispersion media. As a result, we clarified the influence of the dispersion media with an air region on the resulting waveform.