We address a BEMS (Building Energy Management System) to guarantee reliability of electric-power supply in dynamic uncertain environments. The building microgrid as the target of BEMS has multiple distributed power sources including a photo-voltaic power system and Electric-Vehicle (EV). EV is regarded as an autonomously-moving battery due to the original means of transportation and is hence a cause of dynamic uncertainty of the building microgrid. The main objective of synthesis of BEMS in this paper is to guarantee the continuous supply of power to the most critical load in a building microgrid and to realize the power supply to the other loads according to a ranking of load importance. We synthesize the BEMS as a reactive control system that monitors changes of dynamic uncertain environment of the microgrid including departure and arrival of an EV, and determines a route of power supply to the most critical load. Also, we conduct numerical experiments of the reactive BEMS using models of power flows in the building and of charging states of the batteries. The experiments are incorporated with data measured in a practical office building and demonstration project of EMS at Osaka, Japan. We show that the BEMS works for extending the time duration of continuous power supply to the most critical load.

The k-error linear complexity of a sequence is a fundamental concept for assessing the stability of the linear complexity. After computing the k-error linear complexity of a sequence, those bits that cause the linear complexity reduced also need to be determined. For binary sequences with period 2pn, where p is an odd prime and 2 is a primitive root modulo p2, we present an algorithm which computes the minimum number k such that the k-error linear complexity is not greater than a given constant c. The corresponding error sequence is also obtained.

In this paper, we present an Energy-efficient Mobile Group Clustering (EMGC) protocol that supports group mobility and a group handover scheme. The mobile sensor nodes are divided into three categories, namely cluster heads, group leaders and group members. In our cluster formation and group handover scheme, group leaders and cluster heads do most of the communications to save on energy consumption during which group members are placed in the sleep condition. This scheme will reduce the number of control packets and frequent topology changes in the networks. Simulation results show that the EMGC protocol outperforms MN-LEACH, GMAC, MBC protocols in terms of energy dissipation and the number of data items received at a base station.

Timing vernier (i.e., digital-to-time converter) is a key component of the pin-electronics circuit board installed in automated digital-VLSI test equipment, and it is used to create fine delays of less than one-cycle time of a clock signal. This paper presents a new on-the-fly (timing-) jitter suppression technique which makes it possible to use low-power plain-CMOS-logic-based timing verniers. Using a power-compensation line installed at the poststage of the digitally variable delay line, we make every pulse (used as a timing signal) consume a fixed amount of electric energy independent of the required delay amount. Since the power load of intrapowerlines is kept constantly, the jitter increase in the situation of changing the required delay amount on the fly is suppressed. On the basis of the concept, a 10-ns span, 125-MHz timing-vernier macro was designed and fabricated with a CMOS process for logic VLSIs. Every macro installed in a real-time timing-signal generator VLSI achieved the required timing resolution of 31.25ps with a linearity error within 15ps. The on-the-fly jitter was successfully suppressed to a random jitter level (<26ps p-p).

The combination of large-scale antenna arrays and simultaneous wireless information and power transfer (SWIPT), which can provide enormous increase of throughput and energy efficiency is a promising key in next generation wireless system (5G). This paper investigates efficient transceiver design to minimize transmit power, subject to users' required data rates and energy harvesting, in large-scale SWIPT system where the base station utilizes a very large number of antennas for transmitting both data and energy to multiple users equipped with time-switching (TS) or power-splitting (PS) receive structures. We first propose the well-known semidefinite relaxation (SDR) and Gaussian randomization techniques to solve the minimum transmit power problems. However, for these large-scale SWIPT problems, the proposed scheme, which is based on conventional SDR method, is not suitable due to its excessive computation costs, and a consensus alternating direction method of multipliers (ADMM) cannot be directly applied to the case that TS or PS ratios are involved in the optimization problem. Therefore, in the second solution, our first step is to optimize the variables of TS or PS ratios, and to achieve simplified problems. After then, we propose fast algorithms for solving these problems, where the outer loop of sequential parametric convex approximation (SPCA) is combined with the inner loop of ADMM. Numerical simulations show the fast convergence and superiority of the proposed solutions.

Recent advances in phase-sensitive amplifiers (PSAs) using periodically poled LiNbO3 are reviewed. Their principles of operation and distinct features are described. Applications in optical communication are studied in terms of the inline operation and amplification of a sophisticated modulation format. Challenges for the future are also discussed.

A low-complexity signal detection approach based on the Kaczmarz algorithm (KA) is proposed to iteratively realize minimum mean square error (MMSE) detection for uplink massive multiple-input multiple-output (MIMO) systems. While KA is used for straightforward matrix inversion, the MMSE detection requires the computation of the Gram matrix with high complexity. In order to avoid the Gram matrix computation, an equivalent augmented matrix is applied to KA-based MMSE detection. Moreover, promising initial estimation and an approximate method to compute soft-output information are utilized to further accelerate the convergence rate and reduce the complexity. Simulation results demonstrate that the proposed approach outperforms the recently proposed Neumann series, conjugate gradient, and Gauss-Seidel methods in complexity and error-rate performance. Meanwhile, the FPGA implementation results confirm that our proposed method can efficiently compute the approximate inverse with low complexity.

In order to verify the correctness of functional requirements, we have been developing a verification method of the correctness of functional requirements specification using the Requirements Frame model. In this paper, we propose a verification method of non-functional requirements specification in terms of time-response requirements written with a natural language. We established a verification method by extending the Requirements Frame model. We have also developed a prototype system based on the method using Java. The extended Requirements Frame model and the verification method will be illustrated with examples.

Massive multiple-input multiple-output (MIMO) transmission, in which the number of antennas is considerably more than the number of user terminals, has attracted attention as a key technology in next-generation mobile communication systems, because it enables improvements in the service area and interference mitigation with simple signal processing. Multi-beam massive MIMO employing high-power beam selection in the analog part and a blind algorithm in the digital part, such as the constant modulus algorithm that does not need channel state information, has been proposed and shown to offer high transmission efficiency. In this paper, in order to realize higher transmission rates and communication efficiency, we propose a beam-selection method that uses multi-beam amplitude information only. Furthermore, this method can be realized through signal processing with a simple configuration and is highly suitable for hybrid analog-digital massive MIMO, which is advantageous in terms of cost and power consumption. Here, the effectiveness of the proposed method is verified by computer simulation.

This paper studies the secrecy throughput performance of the three-node wireless-powered networks and proposes two secure transmission schemes, namely the half-duplex maximal ratio combining (HD&MRC) scheme and the full-duplex jamming scheme based on time switching simultaneous wireless information and power transfer (FDJ&TS-SWIPT). The closed-form expressions of the secrecy throughput are derived, and intuitive comparison of the two schemes is provided. It is illustrated that the HD&MRC scheme only applies to the low and medium signal-to-noise ratio (SNR) regime. On the contrary, the suitable SNR regime of the FDJ&TS-SWIPT is much wider. It is depicted that FDJ&TS-SWIPT combing with current passive self-interference cancellation (SIC) algorithm outperforms HD&MRC significantly, especially when a medium or high transmit SNR is provided. Numerical simulations are conducted for verifying the validity of the analysis.

This paper proposes a novel access control scheme with collision detection that utilizes multiple-input multiple-output (MIMO) technology. Carrier sense multiple access with collision detection (CSMA/CD) is used in Ethernet wired local area networks (LANs) for media access control (MAC). CSMA/CD can immediately abort a transmission if any collision is detected and is thus able to change to a retransmission state. In Ethernet, CSMA/CD results in a transmission efficiency of approximately 90% because the protocol makes the transmission band available for useful communication by this retransmission function. Conversely, in conventional wireless LANs (WLANs), the packet collisions due to interfering signals and the retransmission due to collisions are significant issues. Because conventional WLANs cannot detect packet collisions during signal transmission, the success of a transmission can only be determined by whether an acknowledgment (ACK) frame has been received. Consequently, the transmission efficiency is low — approximately 60%. The objective of our study is to increase the transmission efficiency of WLANs to make it at least equal to that of Ethernet. Thus, we propose a novel access control scheme with collision detection that utilizes MIMO technology. When preamble signals are transmitted before transmitting data packets from an antenna, the proposed scheme can detect packet collisions during signal transmission at another antenna; then, the affected packets are retransmitted immediately. Two fundamental technologies are utilized to realize our proposed scheme. The first technology is the access control protocol in the MAC layer in the form of the MIMO frame sequence protocol, which is used to detect signal interference. The other technology is signal processing in the physical (PHY) layer that actualizes collision detection. This paper primarily deals with the proposed MAC layer scheme, which is evaluated by theoretical analyses and computer simulations. Evaluation by computer simulations indicate that the proposed scheme in a transmission efficiency of over 90%.

We demonstrate heteroepitaxial growth of GaAs/Ge buffer layers for fabricating 1.3-µm range metamorphic InGaAs-based multiple quantum well (MQW) lasers in which the Ge buffer layer is grown using a metal-organic Ge precursor, iso-butyl germane, in a conventional metal-organic vapor phase epitaxy reactor. This enables us to grow Ge and GaAs buffer layers in the same reactor seamlessly. Transmission electron microscopy and X-ray diffraction analyses indicate that dislocations are well confined at the Ge/Si interface. Furthermore, thermal-cycle annealing significantly improves crystalline quality at the GaAs/Ge interface, resulting in higher photoluminescence intensity from the MQWs on the buffer layers.

We propose an efficient training method for memristor neural networks. The proposed method is suitable for the mini-batch-based training, which is a common technique for various neural networks. By integrating the two processes of gradient calculation in the backpropagation algorithm and weight update in the write operation to the memristors, the proposed method accelerates the training process and also eliminates the external computing resources required in the existing method, such as multipliers and memories. Through numerical experiments, we demonstrated that the proposed method achieves twice faster convergence of the training process than the existing method, while retaining the same level of the accuracy for the classification results.

Individuals can be identified by features extracted from an electrocardiogram (ECG). However, irregular palpitations due to stress or exercise decrease the identification accuracy due to distortion of the ECG waveforms. In this letter, we propose a human identification scheme based on the frequency spectrums of an ECG, which can successfully extract features and thus identify individuals even while exercising. For the proposed scheme, we demonstrate an accuracy rate of 99.8% in a controlled experiment with exercising subjects. This level of accuracy is achieved by determining the significant features of individuals with a random forest classifier. In addition, the effectiveness of the proposed scheme is verified using a publicly available ECG database. We show that the proposed scheme also achieves a high accuracy with this public database.

Because mobile users demand a high quality and energy-friendly video delivery service that efficiently uses wireless resources, we introduce an energy-efficient video delivery system by applying moving route navigation and playout buffer control based on the mobile throughput history data. The proposed system first determines the optimal travel route to achieve high-speed and energy-efficient communications. Then when a user enters a high throughput area, our system temporarily extends the video playout buffer size, and the user aggressively downloads video segments via a high-speed and energy-efficient wireless connection until the extended buffer is filled. After leaving this area, the user consumes video segments from the extended buffer in order to keep smooth video playback without wireless communications. We carry out computer simulations, laboratory and field experiments and confirm that the proposed system can achieve energy-efficient mobile video delivery.

We review the recent advances on strain and temperature sensing techniques based on multimodal interference in perfluorinated (PF) graded-index (GI) polymer optical fibers (POFs). First, we investigate their fundamental characteristics at 1300nm. When the core diameter is 62.5µm, we obtain strain and temperature sensitivities of -112pm/µε and +49.8nm/°C, the absolute values of which are, by simple calculation, approximately 13 and over 1800 times as large as those in silica GI multimode fibers, respectively. These ultra-high strain and temperature sensitivities probably originate from the unique PF polymer used as core material. Subsequently, we show that the temperature sensitivity (absolute value) is significantly enhanced with increasing temperature toward ∼70°C, which is close to the glass-transition temperature of the core polymer. When the core diameter is 62.5µm, the sensitivity at 72°C at 1300nm is 202nm/°C, which is approximately 26 times the value obtained at room temperature and >7000 times the highest value previously reported using a silica multimode fiber. Then, we develop a single-end-access configuration of this strain and temperature sensing system, which enhances the degree of freedom in embedding the sensors into structures. The light Fresnel-reflected at the distal open end of the POF is exploited. The obtained strain and temperature sensitivities are shown to be comparable to those in two-end-access configurations. Finally, we discuss the future prospects and give concluding remarks.

Applying Software Defined Network (SDN) technology to wireless networks are attracting much attention. Our previous study proposed a channel utilization method based on SDN/OpenFlow technology to improve the channel utilization efficiency of the multi-channel wireless backhaul network (WBN). However, since control messages are inherently transmitted with data traffic on a same channel in WBN, it inevitably degrades the network capacity. Specifically, the amount of control messages for collecting statistical information of each flow (FlowStats) linearly increases with the number of ongoing flows, thereby being the dominant overhead for backhaul networks. In this paper, we propose a new method that prevents the increase of control traffic while retaining the network performance of the previous method. Our proposed method uses statistical information of each interface (PortStats) instead of per-flow information (FlowStats), and handles multiple flows on the interface together if possible. Otherwise, to handle individual flow, we propose a way to estimate per-flow information without introducing extra control messages. Finally, we show that the proposed method offers the same performance with the previous method, while greatly reducing the amount of control traffic.

This paper discusses the collection of sensor data for power distribution systems. In current power distribution systems, this is usually performed solely by the Remote Terminal Unit (RTU) which is located at the root of a power distribution network. The recent rise of distributed power sources, such as photovoltaic generators, raises the demand to increase the frequency of data collection because the output of these distributed generators varies quickly depending on the weather. Increasing data collection frequency in turn requires shortening the time required for data collection. The paper proposes the use of aggregation points for this purpose. An aggregation point can collect sensor data concurrently with other aggregation points as well as with the RTU. The data collection time can be shortened by having the RTU receive data from aggregation points, instead of from all sensors. This approach then poses the problem of finding the optimal location of aggregation points. To solve this problem, the paper proposes a Mixed Integer Linear Problem (MILP) formulation of the problem. The MILP problem can then be solved with off-the-shelf mathematical optimization software. The results of experiments show that the proposed approach is applicable to rather large scale power distribution systems.