Open-loop (OL) transmit diversity is more subject to the influence of channel estimation error than closed-loop (CL) transmit diversity, although it has the merit of providing better performance in fast Doppler frequency environments because it doesn't require a feedback signal. This paper proposes an OL transmit diversity scheme combined with intra-subframe frequency hopping (FH) and iterative decision-feedback channel estimation (DFCE) in a shared channel for discrete Fourier transform (DFT)-precoded orthogonal frequency division multiple access (OFDMA). We apply intra-subframe FH to OL transmit diversity to mitigate the reduction in the diversity gain under high fading correlation conditions among antennas and iterative DFCE to improve the channel estimation accuracy. Computer simulation results show that the required average received signal-to-noise power ratio at the average block error rate (BLER) of 10-2 of the space-time block code (STBC) with intra-subframe FH is reduced to within approximately 0.8dB compared to codebook-based CL transmit diversity when using iterative DFCE at the maximum Doppler frequency of fD =5.55Hz. Moreover, it is shown that STBC with intra-subframe FH and iterative DFCE achieves much better BLER performance compared to CL transmit diversity when fD is higher than approximately 30Hz since the tracking ability of the latter degrades due to the fast fading variation in its feedback loop.

Recent studies on switching fabrics mainly focus on the switching schedule algorithms, which aim at improving the throughput (a key performance metric). However, the delay (another key performance metric) of switching fabrics cannot be well guaranteed. A good switching fabric should be endowed with the properties of high throughput, delay guarantee, low component complexity and high-speed multicast, which are difficult for conventional switching fabrics to achieve. This has fueled great interest in designing a new switching fabric that can support large-scale extension and high-speed multicast. Motivated by this, we reuse the self-routing Boolean concentrator network and embed a model of multicast packet copy separation in front to construct a load-balanced multicast switching fabric (LB-MSF) with delay guarantee. The first phase of LB-MSF is responsible for balancing the incoming traffic into uniform cells while the second phase is in charge of self-routing the cells to their final destinations. In order to improve the throughput, LB-MSF is combined with the merits of erasure codes against packet loss. Experiments and analyses verify that the proposed fabric is able to achieve high-speed multicast switching and suitable for building super large-scale switching fabric in Next Generation Network(NGN) with all the advantages mentioned above. Furthermore, a prototype of the proposed switch is developed on FPGA, and presents excellent performance.

All-optical 1-to-6 wavelength multicasting of a 10-Gb/s picosecond-tunable-width converted return-to-zero (RZ)-on-off-keying (OOK) data signal using a wideband-parametric pulse source from a distributed Raman amplifier (DRA) is experimentally demonstrated. Width-tunable wavelength multicasting within the C-band with approximately 40.6-nm of separation with various compressed RZ data signal inputs have been proposed and demonstrated. The converted multicast pulse widths can be flexibly controlled down to 2.67 ps by tuning the Raman pump powers of the DRA. Nearly equal pulse widths at all multicast wavelengths are obtained. Furthermore, wide open eye patterns and penalties less than 1.2 dB at the 10-9 bit-error-rate (BER) level are found.

A millimeter-wave radar receiver using a z-cut LiNbO3 optical modulator with orthogonal-gap-embedded patch-antennas on a low-k dielectric material is proposed. A millimeter-wave from a reflected radar signal can be received by the patch-antennas and converted directly to a lightwave through electro-optic modulation. A low-k dielectric material is used as a substrate for improving antenna gain. Additionally, an interaction length between millimeter-wave and lightwave electric fields becomes long. As a result, large modulation efficiency can be obtained, which is proportional to sensitivity of the millimeter-wave radar receiver. Optical millimeter-wave radar beam-forming can be obtained using the proposed device with meandering-gaps for controlling interaction between millimeter-wave and lightwave electric fields in electro-optic modulation. Analysis and experimentally demonstration of the proposed device are discussed and reported for 40GHz millimeter-wave bands. Optical millimeter-wave radar beam-forming in 2-D is also discussed.

We propose a one-step error detection and correction interface for a voice word processor. This correction interface performs analysis region detection, user intention understanding and error correction utterance recognition, all from a single user utterance input. We evaluate the performance of each component first, and then compare the effectiveness of our interface to two previous interfaces. Our evaluation demonstrates that each component is technically superior to the baselines and that our one-step error detection and correction method yields an error correction interface that is more convenient and natural than the two previous interfaces.

Non-verbal communication incorporating visual, audio, and contextual information is important to make sense of and navigate the social world. Individuals who have trouble with social situations often have difficulty recognizing these sorts of non-verbal social signals. In this article, we propose a training tool NOCOA+ (Non-verbal COmmuniation for Autism plus) that uses utterances in visual and audio modalities in non-verbal communication training. We describe the design of NOCOA+, and further perform an experimental evaluation in which we examine its potential as a tool for computer-based training of non-verbal communication skills for people with social and communication difficulties. In a series of four experiments, we investigated 1) the effect of temporal context on the ability to recognize social signals in testing context, 2) the effect of modality of presentation of social stimulus on ability to recognize non-verbal information, 3) the correlation between autistic traits as measured by the autism spectrum quotient (AQ) and non-verbal behavior recognition skills measured by NOCOA+, 4) the effectiveness of computer-based training in improving social skills. We found that context information was helpful for recognizing non-verbal behaviors, and the effect of modality was different. The results also showed a significant relationship between the AQ communication and socialization scores and non-verbal communication skills, and that social skills were significantly improved through computer-based training.

Directional communications have been considered as a feasible alternative to improve spatial division and throughput in mobile communication environments. In general, directional MAC protocols proposed in the literature rely on channel reservation based on control frames, such as RTS/CTS. Notwithstanding, channel reservation based on control frames increases latency and has an impact on the network throughput. The main contribution of this paper is to propose a channel reservation technique based on pulse/tone signals. The proposed scheme, termed directional pulse/tone channel reservation (DPTCR), allows for efficient channel reservation without resorting to control frames such as RTS and CTS. Theoretical and empirical results show that the proposed scheme has a low probability of failure while providing significant throughput gains. The results show that DPTCR is able to provide throughput improvement up to 158% higher as compared to traditional channel reservation employing RTS/CTS frames.

A quantum dot (QD) electro-absorption device was successfully developed with a highly stacked InAs/InGaAlAs QD structure. A 1.55-µm waveband electro-absorption effect and a quantum confined Stark effect of approximately 22 meV under the application of a 214-kV/cm reverse bias electric field are clearly observed in the developed QD device.

We consider a chain of integrators system that has an uncertain delay in the input. Also, there is a measurement noise in the feedback channel that only noisy output is available. We develop a new output feedback control scheme along with amplification such that the ultimate bounds of all states and output of the controlled system can be made arbitrarily small. We note that the condition imposed on the sensor noise is quite general over the existing results such that the sensor noise is uncertain and is only required to be bounded by a known bound. The benefit of our control method is shown via an example.

In the case of a disaster such as an earthquake or a tsunami, the city, town, and village administration usually issues an evacuation advisory and other information through the Outdoor Public Address Speakers for the disaster reduction broadcasting system covering its area of jurisdiction. However, in areas those have previous experience of a disaster, people frequently voice the lack of audibility of the disaster reduction broadcast. In this research, we conducted a questionnaire survey on the residents in the central area of Ishinomaki City, Miyagi Prefecture, who are the victims of the Great East Japan Earthquake Disaster, on the audible quality of outdoor public address (PA) speakers of the disaster reduction broadcasting system so as to understand the current state of such broadcasts and to propose ideal methods of sending and receiving information at the time of a future disaster.

Track mis-registration (TMR) is one of the major problems in high-density magnetic recording systems such as bit-patterned media recording (BPMR). In general, TMR results from the misalignment between the center of the read head and that of the main track, which can deteriorate the system performance. Although TMR can be handled by a servo system, this paper proposes a novel method to alleviate the TMR effect, based on the readback signal. Specifically, the readback signal is directly used to estimate a TMR level and is then further processed by the suitable target and equalizer designed for such a TMR level. Simulation results indicate that the proposed method can sufficiently estimate the TMR level and then helps improve the system performance if compared to the conventional receiver that does not employ a TMR mitigation method, especially when an areal density is high and/or a TMR level is large.

In this paper, a feature named Non-Redundant Gradient Semantic Local Binary Patterns (NRGSLBP) is proposed for human detection as a modified version of the conventional Semantic Local Binary Patterns (SLBP). Calculations of this feature are performed for both intensity and gradient magnitude image so that texture and gradient information are combined. Moreover, and to the best of our knowledge, non-redundant patterns are adopted on SLBP for the first time, allowing better discrimination. Compared with SLBP, no additional cost of the feature dimensions of NRGSLBP is necessary, and the calculation complexity is considerably smaller than that of other features. Experimental results on several datasets show that the detection rate of our proposed feature outperforms those of other features such as Histogram of Orientated Gradient (HOG), Histogram of Templates (HOT), Bidirectional Local Template Patterns (BLTP), Gradient Local Binary Patterns (GLBP), SLBP and Covariance matrix (COV).

A combination of nonreturn-to-zero (NRZ)-to-return-to-zero (RZ) waveform conversion and wavelength multicasting with pulsewidth tunability is experimentally demonstrated. A NRZ data signal is injected into a highly nonlinear fiber (HNLF)-based four-wave mixing (FWM) switch with four RZ clocks compressed by a Raman amplification-based multiwavelength pulse compressor (RA-MPC). The NRZ signal is multicast and converted to RZ signals in a continuously wide pulsewidth tuning range between around 12.17 and 4.68 ps by changing the Raman pump power of the RA-MPC. Error-free operations of the converted RZ signals with different pulsewidths are achieved with negative power penalties compared with the back-to-back NRZ signal and the small variation among received powers of RZ output channels at a bit-error-rate (BER) of 10-9. The NRZ-to-RZ waveform conversion and wavelength multicasting without using the RA-MPC are also successfully implemented.

In order to tackle the rapidly increasing traffic, the 5th generation (5G) mobile communication system will introduce small cells using higher frequency bands with wider bandwidth to achieve super high bit rate transmission of several tens of Gbps. Massive multiple input multiple output (MIMO) beamforming (BF) is promising as one of the technologies that can compensate for larger path-loss in the higher frequency bands. Joint analog fixed BF and digital precoding have been proposed to reduce the cost of a Massive MIMO transceiver. However, the conventional scheme assumes the transmission of a few streams using well-known codebook-based precoding as the digital precoding, and both a selection method of the fixed BF weights and a digital precoder design, which are suitable for super high bit rate transmission using multiple streams, have not been studied. This paper proposes a joint fixed BF and CSI-based precoding (called FBCP) scheme for the 5G Massive MIMO systems. FBCP first selects the analog fixed BF weights based on a maximum total received power criterion, and then it calculates an eigenmode (EM) precoding matrix by exploiting CSI. This paper targets a 5G system achieving over 20Gbps in the 20GHz band as one example. Throughput performances of the Massive MIMO using the proposed FBCP are evaluated by link level simulations using adaptive modulation and coding and it is shown that the proposed FBCP with the optimum number of selected beams (baseband chains) can use higher level modulation, up to 256QAM, and higher coding rates and achieve throughputs close to 30Gbps while the cost and complexity can be reduced compared with the fully digital Massive MIMO.

Although Quasi Orthogonal Space Time Block Code (QOSTBC) is capable of achieving a full rate transmission for more than two transmit antennas, its generation entails a complex algorithm to create the transmission matrix for a very large number of antennas. This paper presents a simplified generation scheme of QOSTBC, which can be generalized to 2k antennas for any positive integer k. In addition, under a realistic massive MIMO with up to 16 transmit and receive antennas, the performance evaluation is conducted. It is verified that the proposed scheme provides significant performance with BPSK and QPSK modulation formats in Rayleigh fading channels.

With shortest path bridging MAC (SPBM), shortest path trees are computed based on link metrics from each node to all other participating nodes. When an edge bridge receives a frame, it selects a path along which to forward the frame to its destination node from multiple shortest paths. Blocking ports are eliminated to allow full use of the network links. This approach is expected to use network resources efficiently and to simplify the operating procedure. However, there is only one multipath distribution point in the SPBM network. This type of network can be defined as an end-to-end multipath network. Edge bridges need to split flows to achieve the load balancing of the entire network. This paper proposes a rate-based path selection scheme that can be employed for end-to-end multipath networks including SPBM. The proposed scheme assumes that a path with a low average rate will be congested because the TCP flow rates decrease on a congested path. When a new flow arrives at an edge bridge, it selects the path with the highest average rate since this should provide the new flow with the highest rate. The performance of the proposed scheme is confirmed by computer simulations. The appropriate timeout value is estimated from the expected round trip time (RTT). If an appropriate timeout value is used, the proposed scheme can realize good load balancing. The proposed scheme improves the efficiency of link utilization and throughput fairness. The performance is not affected by differences in the RTT or traffic congestion outside the SPBM network.

This paper extends our previously proposed non-orthogonal multiple access (NOMA) scheme to the base station (BS) cooperative multiple-input multiple-output (MIMO) cellular downlink for future radio access. The proposed NOMA scheme employs intra-beam superposition coding of a multiuser signal at the transmitter and the spatial filtering of inter-beam interference followed by the intra-beam successive interference canceller (SIC) at the user terminal receiver. The intra-beam SIC cancels out the inter-user interference within a beam. This configuration achieves reduced overhead for the downlink reference signaling for channel estimation at the user terminal in the case of non-orthogonal user multiplexing and enables the use of the SIC receiver in the MIMO downlink. The transmitter beamforming (precoding) matrix is controlled based on open loop-type random beamforming using a block-diagonalized beamforming matrix, which is very efficient in terms of the amount of feedback information from the user terminal. Simulation results show that the proposed NOMA scheme with block-diagonalized random beamforming in BS cooperative multiuser MIMO and the intra-beam SIC achieves better system-level throughput than orthogonal multiple access (OMA), which is assumed in LTE-Advanced. We also show that BS cooperative operation along with the proposed NOMA further enhances the cell-edge user throughput gain which implies better user fairness and universal connectivity.

Perceptually optimized missing texture reconstruction via neighboring embedding (NE) is presented in this paper. The proposed method adopts the structural similarity (SSIM) index as a measure for representing texture reconstruction performance of missing areas. This provides a solution to the problem of previously reported methods not being able to perform perceptually optimized reconstruction. Furthermore, in the proposed method, a new scheme for selection of the known nearest neighbor patches for reconstruction of target patches including missing areas is introduced. Specifically, by monitoring the SSIM index observed by the proposed NE-based reconstruction algorithm, selection of known patches optimal for the reconstruction becomes feasible even if target patches include missing pixels. The above novel approaches enable successful reconstruction of missing areas. Experimental results show improvement of the proposed method over previously reported methods.

This paper presents the performance of outer-loop control for selecting the best modulation and coding scheme (MCS) based on mutual information (MI) for orthogonal frequency division multiplexing (OFDM) multiple-input multiple-output (MIMO) spatial division multiplexing (SDM). We propose an outer-loop control scheme that updates the measured MI per information bit value for selecting the best MCS from a mapping table that associates the block error rate (BLER) and MI per bit instead of directly updating the MCS selection threshold so that the required BLER is satisfied. The proposed outer-loop control is applicable to continuous data transmission including intermittent transmission with a short blank period. Moreover, we compare the measured BLER and throughput performance for two types of outer-loop control methods: instantaneous block error detection and moving-average BLER detection. In the paper, we use maximum likelihood detection (MLD) for MIMO SDM. Computer simulation results optimize the step size for the respective outer-loop control schemes for selecting the best MCS that achieves the higher throughput and the target BLER simultaneously. Computer simulation results also show that by using the most appropriate step size, the outer-loop control method based on the instantaneous block error detection of each physical resource block is more appropriate than that based on the moving-average BLER detection from the viewpoints of achieving the target BLER more accurately and higher throughput.

Non-orthogonal multiple access (NOMA) utilizing the power domain and advanced receiver has been considered as one promising multiple access technology for further cellular enhancements toward the 5th generation (5G) mobile communications system. Most of the existing investigations into NOMA focus on the combination of NOMA with orthogonal frequency division multiple access (OFDMA) for either downlink or uplink. In this paper, we investigate NOMA for uplink with single carrier-frequency division multiple access (SC-FDMA) being used. Differently from OFDMA, SC-FDMA requires consecutive resource allocation to a user equipment (UE) in order to achieve low peak to average power ratio (PAPR) transmission by the UE. Therefore, sophisticated designs of scheduling algorithm for NOMA with SC-FDMA are needed. To this end, this paper investigates the key issues of uplink NOMA scheduling such as UE grouping method and resource widening strategy. Because the optimal schemes have high computational complexity, novel schemes with low computational complexity are proposed for practical usage for uplink resource allocation of NOMA with SC-FDMA. On the basis of the proposed scheduling schemes, the performance of NOMA is investigated by system-level simulations in order to provide insights into the suitability of using NOMA for uplink radio access. Key issues impacting NOMA performance are evaluated and analyzed, such as scheduling granularity, UE number and the combination with fractional frequency reuse (FFR). Simulation results verify the effectiveness of the proposed algorithms and show that NOMA is a promising radio access technology for 5G systems.