This paper proposes an accurate and efficient method to calculate probability distributions of pulse-shaped complex signals. We show that the distribution over the in-phase and quadrature-phase (I/Q) complex plane is obtained by a recursive probability mass function of the accumulator for a pulse-shaping filter. In contrast to existing analytical methods, the proposed method provides complex-plane distributions in addition to instantaneous power distributions. Since digital signal processing generally deals with complex amplitude rather than power, the complex-plane distributions are more useful when considering digital signal processing. In addition, our approach is free from the derivation of signal-dependent functions. This fact results in its easy application to arbitrary constellations and pulse-shaping filters like Monte Carlo simulations. Since the proposed method works without numerical integrals and calculations of transcendental functions, the accuracy degradation caused by floating-point arithmetic is inherently reduced. Even though our method is faster than Monte Carlo simulations, the obtained distributions are more accurate. These features of the proposed method realize a novel framework for evaluating the characteristics of pulse-shaped signals, leading to new modulation, predistortion and peak-to-average power ratio (PAPR) reduction schemes.

Microwave imaging techniques, in particular, synthetic aperture radar (SAR), are promising tools for terrain surface measurement, irrespective of weather conditions. The coherent change detection (CCD) method is being widely applied to detect surface changes by comparing multiple complex SAR images captured from the same scanning orbit. However, in the case of a general damage assessment after a natural disaster such as an earthquake or mudslide, additional about surface change, such as surface height change, is strongly required. Given this background, the current study proposes a novel height change estimation method using a CCD model based on the Pauli decomposition of fully polarimetric SAR images. The notable feature of this method is that it can offer accurate height change beyond the assumed wavelength, by introducing the frequency band-divided approach, and so is significantly better than InSAR based approaches. Experiments in an anechoic chamber on a 1/100 scaled model of the X-band SAR system, show that our proposed method outputs more accurate height change estimates than a similar method that uses single polarimetric data, even if the height change amount is over the assumed wavelength.

Microwave imaging techniques, particularly for synthetic aperture radar (SAR), produce high-resolution terrain surface images regardless of the weather conditions. Focusing on a feature of complex SAR images, coherent change detection (CCD) approaches have been developed in recent decades that can detect invisible changes in the same regions by applying phase interferometry to pairs of complex SAR images. On the other hand, various techniques of polarimetric SAR (PolSAR) image analysis have been developed, since fully polarimetric data often include valuable information that cannot be obtained from single polarimetric observations. According to this background, various coherent change detection methods based on fully polarimetric data have been proposed. However, the detection accuracies of these methods often degrade in low signal-to-noise ratio (SNR) situations due to the lower signal levels of cross-polarized components compared with those of co-polarized ones. To overcome the problem mentioned above, this paper proposes a novel CCD method by introducing the Pauli decomposition and the weighting of component with their respective SNR. The experimental data obtained in anechoic chamber show that the proposed method significantly enhances the performance of the receiver operation characteristic (ROC) compared with that obtained by a conventional approach.

Synthetic aperture radar (SAR) is an indispensable tool for low visibility ground surface measurement owing to its robustness against optically harsh environments such as adverse weather or darkness. As a leading-edge approach for SAR image processing, the coherent change detection (CCD) technique has been recently established; it detects a temporal change in the same region according to the phase interferometry of two complex SAR images. However, in the case of general damage assessment following an earthquake or mudslide, the technique requires not only the detection of surface change but also an assessment for height change quantity, such as occurs with a building collapse or road subsidence. While the interferometric SAR (InSAR) approach is suitable for height assessment, it is basically unable to detect change if only a single observation is made. To address this issue, we previously proposed a method of estimating height change according to phase interferometry of the coherence function obtained by dual band-divided SAR images. However, the accuracy of this method significantly degrades in noisy situations owing to the use of the phase difference. To resolve this problem, this paper proposes a novel height estimation method by exploiting the frequency characteristic of coherence phases obtained by each SAR image multiply band-divided. The results obtained from numerical simulations and experimental data demonstrate that our proposed method offers accurate height change estimation while avoiding degradation in the spatial resolution.

To visualize the biochemical distribution two-dimensionally, we invented a solid-state-type ion image sensor that indicates the chemical activity of solutions and cells. The device, which consists of a CCD array covered with a functionalized membrane to detect charge accumulation, is highly sensitive to changes in the concentration and two-dimensional distribution of ions and biomaterials.

In this paper, a novel charge coupled device matched filter (CCD-MF) for Electrical code division multiplexing (ECDM) decoder is proposed and experimentally demonstrated. Simulation results clarify the influence of low charge transfer efficiency (CTE) and the validity of a parallel CCD-MF we proposed. A 15-channel ECDM system using a 2 Gchip/s, 2-parallel CCD-MF is experimentally demonstrated.

Satellite-borne SAR (synthetic aperture radar) is for high-resolution geosurface measurements. Recently, a feature extraction method based on CCD (coherent change detection) was developed, where a slight surface change on the geosurface is detected using the phase relationship between sequential complex SAR images of the same region made at different times. For accurate detection of the surface change, the log-likelihood method has been proposed. This method determines an appropriate threshold for change detection, making use of the phase characteristic of the changed area, and thus enhances the detection probability. However, this and other conventional methods do not seek to proactively employ phase information of the estimated coherence function, and their detection probability is often low, especially in the case that the target has small surface or local uniform changes. To overcome this problem, this paper proposes a novel transformation index that considers the phase difference of the coherence function. Furthermore, we introduce a pre-processing calibration method to compensate the bias error for the coherence phase which resulting mainly from the orbit error of the antenna platform. Finally, the results from numerical simulations and experiment modeling of the geosurface measurement verify the effectiveness of the proposed method, even in situations with low SNR (signal to noise ratio).

An electromagnetic relay (EMR) is widely used in automatic control field, and its dynamic characteristics play a significant role in EMR researches. According to structural features of the EMR, a dynamic characteristics testing and analyzing system (DCTAS) based on CCD digital image processing technique is designed and implemented. By using the DCTAS, the dynamic characteristics (include displacement, velocity, acceleration and force characteristics) of EMR whose operating time is less than 12 ms and armature travel is less than 10 mm can be investigated. The comparison of testing data obtained by the DCTAS and that of by a high speed camera indicates the validity of the system to EMR dynamic characteristics testing.

The vacuum sealing process with a base vacuum of 10-5 Torr is adopted to minimize the residual impurity gas. The address and sustain discharges in the 42-in PDP prepared by the vacuum-sealing process are observed by using the ICCD. As a result, the ICCD observation illustrates that thanks to the reduction of the impurity level by the vacuum-sealing process, the surface and plate-gap discharges are initiated and extinguished very fast and the corresponding IR emissions are also intensified.

A mode-matching model for an electromagnetically coupled coaxial dipole array antenna is presented. The Fourier transfor m/series technique is used to represent the continuous and discrete modes of scattered fields. The mode-matching is utilized to constitute a set of simultaneous equations for discrete modal coefficients. Numerical computation is performed to show its radiation behavior in terms of various antenna parameters.

A set of three optical filters was designed and a camera system was developed using these filters in order to capture high-fidelity colors within the gamut of vision. Photographs of a number of highly saturated colors and a combination of the Macbeth chart and 18 pieces of clothing samples of various colors were taken. A 39 matrix was used to convert the camera output signals into XYZ tristimulus data. The tristimulus values of the colors were compared with those of the images captured by the camera. The average color difference, ΔE, for these samples were found to be 2.16 and 1.18, respectively.

An HEMT CCD (charge-coupled-device) matched filter for spread-spectrum communication was developed. For higher data rates, it was fabricated using a two-phase CCD based on HEMT technology. It operates at 1.6 GHz, and its calculated data rate is 100 Mbps with a PN data length of 16 bits (PN data rate is 1.6 GHz). And it attains a charge transfer efficiency (CTE) of 0.975 at 2 GHz. The HEMT CCD matched filter dissipates 173 mW from a 10-Vp-p supply, and its chip size is 0.961.03 mm. It will thus be useful for optical communication and other high-data-rate applications utilizing spread-spectrum (SS) communication.

In this paper, we develop an image-based tracking algorithm of multiple vehicles performing effective detection and tracking of moving objects under adverse environmental conditions. In particular, we employ low cost commercial off-the-shelf IR or CCD image sensor for generating continuous images of multiple moving vehicles. The motion in image sequences is first detected by adaptive background estimation and then tracked by Kalman filtering with the attribute information being updated by data association. Upon applying a modified Retinex procedure as preprocessing to reduce the illumination effects, we proceed with a two-step tracking algorithm. The first step achieves blob grouping and then judicially selects the true targets for tracking using data association through information registration. In the second stage, all blobs detected go through a validation for screening as well as for occlusion reasoning, and those found pertinent to the real object survive to become the 'Object' state for stable tracking. The results of representative tests confirm its effectiveness in vehicle tracking under both daylight and nighttime conditions while resolving occlusions.

This paper presents the design considerations for a digital dental X-ray system with a commercial CCD sensor. Especially the system should be able to work with several X-ray machines even with them for the classical film. The hardware-software co-design methodology is employed to optimize the system. The full digital implementation is assumed for the reliability of the system. The considered functions cover the pre-processing such as the exposure detection, clamping and the dark level correction and the post-processing such as gray level compensation. It is analyzed with some other constraints in order to make the final partition. The entire system based on the partition will be described.

An automatic LSI package lead inspection system for backside lead specification is proposed. The proposed system inspects not only lead backside contamination but also the mechanical lead specification such as lead pitch, lead offset and lead overhangs (variations in lead lengths). The total inspection time of a UQFP package with a lead count of 256 is less than the required time of 1 second. Our proposed method is superior to the threshold method used usually, especially for the defect between leads.

In order to assess the possible impacts of meteors with spacecraft, which is among major hazard in the space environment, it is essential to establish an accurate statistics of their mass and velocity. We developed a radar-optical combined system for detecting faint meteors consisting of a powerful VHF Doppler radar and an ICCD video camera. The Doppler pulse compression scheme is used to enhance the S/N ratio of the radar echoes with very large Doppler shifts, as well as to determine their range with a resolution of 200 m. A very high sensitivity of more than 14 magnitude and 9 magnitude for radar and optical sensors, respectively, has been obtained. Instantaneous direction of meteor body observed by the radar is determined with the interferometry technique. We examined the optimum way of the receiving antenna arrangements, and also of the signal processing. Its absolute accuracy was confirmed by the optical observations with background stars as a reference. By combining the impinging velocity of meteor bodies derived by the radar with the absolute visual magnitude determined by the video camera simultaneously, the mass of each meteor body was estimated. The developed observation system will be used to create a valuable data base of the mass and velocity information of faint meteors, on which very little is known so far. The data base is expected to play a vital role in our understanding of the space environment needed for designing large space structures.

In this paper, a method of fusing ground-based laser range image and CCD images for the reconstruction of textured 3D urban object is proposed. An acquisition system is developed to capture laser range image and CCD images simultaneously from the same platform. A registration method is developed using both laser range and CCD images in a coarse-to-fine process. Laser range images are registered with an assumption on sensor's setup, which aims at robustly detecting an initial configuration between the sensor's coordinate system of two views. CCD images are matched to refine the accuracy of the initial transformation, which might be degraded by improper sensor setup, unreliable feature extraction, or limited by low spatial resolution of laser range image. Textured 3D model is generated using planar faces for vertical walls and triangular cells for ground surface, trees and bushes. Through an outdoor experiment of reconstructing a building using six views of laser range and CCD images, it is demonstrated that textured 3D model of urban objects can be generated in an automated manner.

In this letter we propose a new Shape from Focus (SFF) method using piecewise curved search windows for accurate 3-D shape recovery. The new method uses piecewise curved windows to compute focus measure and to search for Focus Image Surface (FIS) in image space. The experimental result shows that our new method gives more accurate result than the previous SFF methods.

A low dark current CCD linear image sensor with pixels consisting of a photodiode and a storage area has been developed. In order to suppress the dark current, the wafer process has been improved. An impurity profile of a photodiode was modified to minimize depletion width, which was monitored by the photodiode potential. Surface states under the storage gate were decreased by hydrogen annealing with plasma-deposited silicon nitride as an inter metal dielectric film. As the isolation dose decreased, the dark current both in the photodiode and in the storage region were effectively suppressed. Finally, low dark currents of 5 pA/cm2 at photodiode and 120 pA/cm2 at storage area were obtained.

In this article, a new multiplication type D/A conversion system using CCD is proposed and the result of simulations for evaluating its performance is reported. The system consists of a recursive charge divider which divides input charge-packet Qin sequentially into output charge-packets Qin2-i and two charge-packet accumulators which accumulates output charge-packets from the recursive divider selectively according to digital input signal bits atarting from MSB. The system converts input digital signal bit by bit, fully in chargedomain, thus the power consumption for this system is supposed to be very low. Also in this article, an effective method to achieve higher accuracy for splitting a charge-packet into two equal-sized packets using very simple hard-ware structure is proposed. As the result of simulations, we have found that the upper limit of accuracy for the conversion is determined by transfer efficiency of CCD, and within this range a trade-off relationship exists among conversion-accuracy, circuit-size and conversion-rate. This unique relationship enables to reduce the circuit size of D/A converter significantly maintaining the accuracy of conversion by slowing down the conversion-rate. This D/A converter is appropriate especially for the system integration because of its simple structure, tolerance to the fabrication error and low power consumption inherrent in the nature of CCD. By using of this system, it is expected to be possible to realize a focal plane image processor performing parallel analog operations such as DCT conversion with CCD imager incorporated on the same Si chip by the same MOS process technology.