In this letter, we demonstrate a Relay-based Adaptive Auto Rate (RAAR) protocol that can find a suitable relay node for data transmission between transmitter and receiver, and can dynamically adjust its modulation scheme to achieve the maximal throughput of a node according to the transmission distance and the channel condition. Evaluation results show that this scheme provides significant throughput improvement for nodes located at the fringe of the AP's transmission range, thus remarkably improving overall system performance.

In this paper, a method based on the Radiative Energy Transfer theory (RET) to estimate the scattered radio signals from isolated groups of trees is presented. The proposed method consists of measuring the re-radiation function of each tree in the group, parameterising the function and subsequently using these in a discrete algorithm to estimate the overall attenuation at any location within the forest scenario. The discrete algorithm (dRET) presented here has some major improvements over previously published ones, offering substantially enhanced applicability. These improvements allow the use of larger vegetation cells, the enhancement of angular resolution of predicted results and the consideration of the receiving antenna radiation pattern. The estimated received signals using the re-radiation function, on the one hand, and its parameterised counterpart, on the other hand, are compared with measurements performed inside an anechoic chamber on Ficus Benjamina indoor plants at 20 and 62.4 GHz. The overall model performance was assessed in terms of RMS error between measured and predicted results.

This paper addresses the variation of the attenuation characteristics of the Specific Absorption Rate (SAR) in a lossy medium as a function of the distance between an antenna and the medium with different EM-source sizes. Analysis and measurements were performed using a dipole antenna at 900 MHz and a COST244 cubic phantom. From this, an empirical equation has been derived, representing the attenuation characteristics of the SAR. The equation takes into consideration an energy loss due to the spatial spread of electromagnetic waves. In the case where an antenna is placed more than λ/2π away from the medium, the attenuation characteristics of the SAR are those obtained from plane waves in the lossy medium. In the case where a half-wavelength dipole antenna is located close to the medium, at a distance of less than λ/2π, the attenuation characteristics of the SAR are calculated from an equation that includes a loss caused by the spread of energy as a cylindrical wave. Moreover, when the length of antenna is short, it is found that a spatial attenuation factor appropriate to a spherical wave should be taken into account.

We have developed an experimental approach that allows us to estimate the performance of a large-scale enterprise network to update routing information. This approach was applied to the integration of the UFJ Bank network system on January 15, 2002. The main characteristic of this approach is the application of a formula that represents the delays in updating routing information that accompany reductions in CPU resources. This procedure consists of two steps: one is to estimate the reduction in the availability of CPU resources caused by forwarding of data packets at a router, and the other is to estimate the levels of CPU resources required for replying to a query about a new route and subsequently updating the routing information. These steps were applied to estimate the performance of the network in terms of routing information convergence. The results of our experiments on the network showed that updating the routing information was possible as long as the average level of CPU utilization during any five-minute period at the routers was less than 40%. We were able to apply this guideline and thus confirm the stability of the UFJ Bank network.

In this paper, we describe a development of a Bluetooth Access Point for the WAN connection of home network devices. Especially, users can access the PSTN at home instead of expensive CDMA network through the AP, using the 'one-phone,' which is the Bluetooth enabled cellular phone. The one-phone service becomes a convergence of wired and wireless communication through the AP.

New decoding algorithms for binary linear codes based on the concave-convex procedure are presented. Numerical experiments show that the proposed decoding algorithms surpass Belief Propagation (BP) decoding in error performance. Average computational complexity of one of the proposed decoding algorithms is only a few times greater than that of the BP decoding.

Power consumption is a major concern in embedded microprocessors design. Reducing power has also been a critical design goal for general-purpose microprocessors. Since they require high performance as well as low power, power reduction at the cost of performance cannot be accepted. There are a lot of device-level techniques that reduce power with maintaining performance. They select non-critical paths as candidates for low-power design, and performance-oriented design is used only in speed-critical paths. The same philosophy can be applied to architectural-level design. We evaluate a technique, which exploits dynamic information regarding instruction criticality in order to reduce power. We evaluate an instruction steering policy for a clustered microarchitecture, which is based on instruction criticality, and find it is substantially energy-efficient while it suffers performance degradation.

BGP might experience a lengthy path exploration process to reach the convergence after the routing changes. found that the BGP rate-limiting timer--MinRouteAdvertisementInterval (MRAI) has an optimal value Mo that achieves the best trade-off between the stability and the convergence speed. In this paper, with the aid of a timed BGP model, we investigate the effects of MRAI and its optimal value Mo for the BGP convergence process. We find that an adequately long MRAI timer can batch-remove candidate paths and ensure the routing stability in the convergence process. There exists a minimal MRAI Ms that achieves the effect, which is also the upper bound of Mo and provides an approximation of Mo. We calculate the approximations of Ms for different settings and estimate the optimal MRAI for the Internet. According to the results, the optimal MRAI for the Internet might be 5-10 times less than the current default value used in the Internet. The simulations taken with SSFNet and the experiments conducted over the Planet-Lab demonstrate the correctness of our analysis.

This paper describes a sub-1-V power-supply, which is useful for self-powered short-range wireless systems with ambient energy sources. A variable-stage DC-DC converter, which consists of multi-stage switched capacitor circuits and has intermittent operation with an external capacitor, makes it possible to extend the time for self-powered operation. We fabricated a variable-stage DC-DC converter and an intermittent operation circuit with a 0.8-µm CMOS/SOI process. We also applied the sub-1-V power-supply system to a self-powered short-range wireless system and verified its effectiveness.

Radio frequency identification (RFID) enables everyday objects to be identified, tracked, and recorded. The RFID tags are must be extremely simple and of low cost to be suitable for large scale application. An efficient RFID anti-collision mechanism must have low access latency and low power consumption. This paper investigates how to recognize multiple RFID tags within the reader's interrogation ranges without knowing the number of tags in advance by using framed ALOHA. To optimize power consumption and overall tag read time, a combinatory model was proposed to analyze both passive and active tags with consideration on capture effect over wireless fading channels. By using the model, the parameters on tag set estimation and frame size update were presented. Simulations were conducted to verify the analysis. In addition, we come up with a proposal to combat capture effect in deterministic anti-collision algorithms.

For future generation mobile networks, we expect that the mobile devices like PDAs, note PCs or any VoIP-enabled communicators will have the feature of being always switched on, ready for service, constantly reachable by the wireless Internet. In addition to high access speed, attractive real-time contents or other expected spectacular features of the future wireless Internet environment, the mobile terminals has to be very much energy-aware to enable literal untethered movement of the user. Mechanisms for network activities like maintaining location information and wireless system discovery, which require regular network access, should be energy-efficient and resource-efficient in general. Cellular systems employ the notion of passive connectivity to reduce the power consumption of idle mobile hosts. In IP based Multi-service User Terminal (MUT) that may have multiple wireless interfaces for receiving various classes of services from the network, there should be an efficient addressing of the energy consumption issue. To devise an energy-efficient scheme for simultaneous or single operation of the wireless interfaces attached to such terminals we should have comprehensive understanding of the power consumption of the devices/modules in various operational states. This paper investigates the power consumption pattern or behavior of some selected wireless interfaces that are good candidates for being part of the future of the multi-service user terminals. We propose a simple model for predicting energy consumption in a terminal attributed to the wireless network interfaces. We measured the actual consumption pattern to estimate the parameters of the model.

The paper first researches the properties of neural networks in the framework of the dual linear programming theory, then discusses the variation range of a Hessian matrix associated to dual linear programming problems. By means of eigenvalues method, a Lipschitz constant based formula for determining the algorithm step-size is presented. Two examples are given to show that the proposed formula is efficacious.

The effects of air-intake format of forced-air-cooled equipment on the efficiency of air conditioning systems are studied. A modern data center features a large number of information-processing devices to provide telecommunication services. These devices generate considerable heat, and the equipment that houses these devices often employs "forced air cooling" in which a cooling effect is achieved by sucking in large amounts of room air. An air conditioning system used for a machine room filled with such equipment therefore requires high fan driving power resulting in significantly low air conditioning efficiency. In this study, we first performed mockup-based experiments to obtain a quantitative understanding of how different air-intake formats for equipment affect the temperature at various room locations such as equipment intake. We then created a model for predicting the temperature at various locations, and on the basis of this model, we analyzed the factors affecting intake temperature and examined how intake temperature affects air conditioning efficiency. It was found that placing air inlets in the lower 1/3 portion of forced-air-cooled equipment could prevent the equipment from reabsorbing the hot air that it blows out and therefore improve air conditioning efficiency.

A switched nonlinear system is considered, and the interval between two consecutive switchings is assumed to be greater than a value called "the dwell time." When switching among nonlinear systems, using a constant dwell time generally fails to lead to stability. In this letter, a state dependent dwell time function with convergence guarantees is presented for discrete-time stable nonlinear systems.

This development proposes a highly efficient air-conditioning airflow system for a computer-machine room having high-heat-generating equipment using forced-air cooling. The proposed system recirculates room air in the area surrounding equipment back to the cooling supply air supplied from a double floor. The recirculated air is therefore used as cooling air for computers. This system enables the blowing temperature difference of air-conditioner units to be increased, blower capacity to be decreased, and overall efficiency of air-conditioner units to be increased. Here, we have proposed an air-conditioning airflow system that decreases the amount of cooling supply air while ensuring adequate air ventilation for equipment using forced-air cooling, and a design method for achieving this system.

We have developed manganese-based lithium secondary battery technology as a part of a 10-year national project in Japan for The Development of Dispersed-Type Battery Energy Storage Technology. The cell chemistry we developed consisted of a modified graphite anode material containing dispersed Ag particles, and a partially substituted LiMn2O4 cathode with Li in the Mn sites. These materials showed a significant improvement in a cell's cycle life performance. The 250 Wh class single cell with the cell chemistry mentioned above showed energy densities of 131 Wh/kg and 295 Wh/dm3. The 2 kWh class module battery including 8 cells connected in series and a battery management system delivered energy densities of 122 Wh/kg and 255 Wh/dm3 that exceeded the final target of 120 Wh/kg and 240 Wh/dm3 for the project. Most of the target items for the battery performance were accomplished and proved. Thus the basis for practical application was developed, however, some areas concerning the further durability under various circumstances and conditions still remain to be accomplished. Continuous development for mass production and cost reduction is also expected for this technology in order to contribute to industry and society.

As Internet access had spread, it has become an important potential means of lifeline communication. The Internet can fulfill a role in the everyday life of citizens by offering lifeline communication services such as the police, ambulance, gas, electricity, and water services when an emergency occurs. In these lifeline communications, a caller needs to be able to communicate with the nearby lifeline service in the same manner as on a PSTN (Public Switched Telephone Networks) without being consciously aware of the path the caller's message is taking. Moreover, the lifeline service agency must be able to acquire the caller's location and identity. However, it is very difficult to transfer these essential functions from the PSTN to the Internet without making significant changes, because of large differences between the PSTN and the Internet. In this paper, we discuss how to obtain these functions for lifeline communications in the Internet. We further propose a model and implement a lifeline communication system on the Internet.

A UPS with an energy storage function using long-cycle-life VRLA batteries has been developed. Combining the functions of UPS and energy storage is effective to enhance the cost-effectiveness of the UPS. New long-cycle-life VRLA batteries, with capacities of 1000 or 1500 Ah at 2 V, have been developed for the UPS. A cycle life of 3000 or more cycles was estimated from our cycle test. The UPS has been installed in a telecommunications building for field-testing. This paper describes the system configuration, electrical characteristics of the UPS and its components, and result of our field test.

In the formerly proposed theory for sub-linear (linear in a changed addition rule) systems, we developed a sub-linear mathematical theory and demonstrated its capability in several sub-linear systems. In this paper, we assert that we can further construct hybrid systems useful in engineering by combining sub-linear systems with linear systems, and as an example, we show the construction of a divergence-free electrodynamics. Since the energy of photon fields in engineering is tending upward, it would be desirable for us to get rid of the divergence difficulties encountered in the conventional high energy electrodynamics. The most important result is the recognition that Nature herself has a hybrid system composed of sub-linear photon fields and linear electron fields. Mathematically, our electrodynamics is formulated by only one point correction (the insertion of tanh into the electromagnetic energy density) in the conventional electrodynamics of photons and electrons (including positrons).

This report describes a concrete method for realizing adiabatic charging reversible logic. First, we investigate the stabilization properties of a charge recycle regenerator using a switched capacitor circuit by SPICE simulation and an analytical method. In the N-step case, we proved that a step waveform is spontaneously generated. Next, for combinational logic, we propose an adiabatic charging binary decision diagram logic gate (AC-BDD) that uses this regenerator. The AC-BDD uses pass transistor logic based on a BDD, which is suitable for adiabatic logic. 8-bit AC-BDD multipliers were fabricated, and it is clarified that power consumption is reduced to 15% that of the same-rule-designed CMOS at 1 V and 1 MHz. Finally, we propose clocked energy reversible logic (CERL) that maintains the CMOS architecture for CMOS compatibility. CERL can reduce the clocked energy, which is used for charging the clock load capacitance, to 10% that of CMOS by using a power clock from the charge recycle regenerator.