In this paper, the performance of orthogonal space-time block codes (OSTBC) for distributed multiple-input multiple-output (MIMO) systems employing adaptive M-QAM transmission is investigated over independent but not necessarily identically distributed (i.n.i.d.) generalized-K fading channels with arbitrary positive integer-valued k(inversely reflects the shadowing severity) and m (inversely reflects the fading severity). Before this, i.n.i.d. generalized-K fading channel has never been considered for distributed OSTBC-MIMO systems. Especially, the effects of the shape parameter k on the distributed OSTBC-MIMO system performance are unknown. Thus, we investigate mainly the significance of the shape parameter k on the distributed OSTBC-MIMO system performance, in terms of the average symbol error probability (SEP), outage probability, and spectral efficiency (SE). By establishing the system model, the approximated probability density function (PDF) of the equivalent signal to noise ratio (SNR) is derived and thereafter the approximated closed-form expressions of the above performance metrics are obtained successively. Finally, the derived expressions are validated via a set of Monte-Carlo simulations and the implications of the shape parameter k on the overall performance are highlighted.
Tomoko KAWASE Kenta NIWA Masakiyo FUJIMOTO Kazunori KOBAYASHI Shoko ARAKI Tomohiro NAKATANI
We propose a microphone array speech enhancement method that integrates spatial-cue-based source power spectral density (PSD) estimation and statistical speech model-based PSD estimation. The goal of this research was to clearly pick up target speech even in noisy environments such as crowded places, factories, and cars running at high speed. Beamforming with post-Wiener filtering is commonly used in many conventional studies on microphone-array noise reduction. For calculating a Wiener filter, speech/noise PSDs are essential, and they are estimated using spatial cues obtained from microphone observations. Assuming that the sound sources are sparse in the temporal-spatial domain, speech/noise PSDs may be estimated accurately. However, PSD estimation errors increase under circumstances beyond this assumption. In this study, we integrated speech models and PSD-estimation-in-beamspace method to correct speech/noise PSD estimation errors. The roughly estimated noise PSD was obtained frame-by-frame by analyzing spatial cues from array observations. By combining noise PSD with the statistical model of clean-speech, the relationships between the PSD of the observed signal and that of the target speech, hereafter called the observation model, could be described without pre-training. By exploiting Bayes' theorem, a Wiener filter is statistically generated from observation models. Experiments conducted to evaluate the proposed method showed that the signal-to-noise ratio and naturalness of the output speech signal were significantly better than that with conventional methods.
Tran-Nhut-Khai HOAN Vu-Van HIEP Insoo KOO
In this paper, we consider optimal sensing scheduling for sequential cooperative spectrum sensing (SCSS) technique in cognitive radio networks (CRNs). Activities of primary users (PU) on a primary channel are captured by using a two states discrete time Markov chain process and a soft combination is considered at the FC. Based on the theory of optimal stopping, we propose an algorithm to optimize the cooperative sensing process in which the FC sequentially asks each CU to report its sensing result until the stopping condition that provides the maximum expected throughput for the CRN is satisfied. Simulation result shows that the performance of the proposed scheme can be improved by further shortening the reporting overhead and reducing the probability of false alarm in comparison to other schemes in literature. In addition, the collision ratio on the primary channel is also investigated.
Minoru KURIBAYASHI Shogo SHIGEMOTO Nobuo FUNABIKI
In conventional spread spectrum (SS) watermarking schemes, random sequences are used for the modulation of watermark information. However, because of the mutual interference among those sequences, it requires complicated removal operation to improve the performance. In this paper, we propose an efficient spread spectrum watermarking scheme by introducing the orthogonal frequency divisiion multiplexing (OFDM) technique at the modulation of watermark information. The SS sequences in the proposed method are the DCT basic vectors modulated by a pseudo-random number (PN) sequence. We investigate the SS-based method considering the host interference at the blind detection scenario and analyze the noise caused by attacks. Because every operation is invertible, the quantization index modulation (QIM)-based method is applicable for the OFDM modulated signals. We also consider the property of watermark extracting operation in SS-based and QIM-based method and formalize their models of noisy channel in order to employ an error correcting code. The performance of their methods with error correcting code is numerically evaluated under the constraints of same distortion level in watermarked content. The experimental results indicated a criteria for the selection of SS-based and QIM-based methods for given content, which is determined by the amount of host interference. In case that the host interference is 0.8 times smaller than a watermark signal, the SS-based method is suitable. When it is 1.0 times larger, the QIM-based method should be selected.
Shiyu REN Zhimin ZENG Caili GUO Xuekang SUN
Compressed sensing (CS)-based wideband spectrum sensing has been a hot topic because it can cut high signal acquisition costs. However, using CS-based approaches, the spectral recovery requires large computational complexity. This letter proposes a wideband spectrum sensing algorithm based on multirate coprime sampling. It can detect the entire wideband directly from sub-Nyquist samples without spectral recovery, thus it brings a significant reduction of computational complexity. Compared with the excellent spectral recovery algorithm, i.e., orthogonal matching pursuit, our algorithm can maintain good sensing performance with computational complexity being several orders of magnitude lower.
Kwang-Yul KIM Seung-Woo LEE Yu-Min HWANG Jae-Seang LEE Yong-Sin KIM Jin-Young KIM Yoan SHIN
A chirp spread spectrum (CSS) system uses a chirp signal which changes the instantaneous frequency according to time for spreading a transmission bandwidth. In the CSS system, the transmission performance can be simply improved by increasing the time-bandwidth product which is known as the processing gain. However, increasing the transmission bandwidth is limited because of the spectrum regulation. In this letter, we propose a correlation-based chirp rate allocation method to improve the transmission performance by analyzing the cross-correlation coefficient in the same time-bandwidth product. In order to analyze the transmission performance of the proposed method, we analytically derive the cross-correlation coefficient according to the time-bandwidth separation product and simulate the transmission performance. The simulation results show that the proposed method can analytically allocate the optimal chirp rate and improve the transmission performance.
In this paper, we propose the application of principal component analysis (PCA) to scale-spaces. PCA is a standard method used in computer vision. Because the translation of an input image into scale-space is a continuous operation, it requires the extension of conventional finite matrix-based PCA to an infinite number of dimensions. Here, we use spectral theory to resolve this infinite eigenvalue problem through the use of integration, and we propose an approximate solution based on polynomial equations. In order to clarify its eigensolutions, we apply spectral decomposition to Gaussian scale-space and scale-normalized Laplacian of Gaussian (sLoG) space. As an application of this proposed method, we introduce a method for generating Gaussian blur images and sLoG images, demonstrating that the accuracy of such an image can be made very high by using an arbitrary scale calculated through simple linear combination. Furthermore, to make the scale-space filtering efficient, we approximate the basis filter set using Gaussian lobes approximation and we can obtain XY-Separable filters. As a more practical example, we propose a new Scale Invariant Feature Transform (SIFT) detector.
Arata KAWAMURA Hiro IGARASHI Youji IIGUNI
Image-to-sound mapping is a technique that transforms an image to a sound signal, which is subsequently treated as a sound spectrogram. In general, the transformed sound differs from a human speech signal. Herein an efficient image-to-sound mapping method, which provides an understandable speech signal without any training, is proposed. To synthesize such a speech signal, the proposed method utilizes a multi-column image and a speech spectral phase that is obtained from a long-time observation of the speech. The original image can be retrieved from the sound spectrogram of the synthesized speech signal. The synthesized speech and the reconstructed image qualities are evaluated using objective tests.
Shuai LIU Licheng JIAO Shuyuan YANG Hongying LIU
Restoration is an important area in improving the visual quality, and lays the foundation for accurate object detection or terrain classification in image analysis. In this paper, we introduce Beta process priors into hierarchical sparse Bayesian learning for recovering underlying degraded hyperspectral images (HSI), including suppressing the various noises and inferring the missing data. The proposed method decomposes the HSI into the weighted summation of the dictionary elements, Gaussian noise term and sparse noise term. With these, the latent information and the noise characteristics of HSI can be well learned and represented. Solved by Gibbs sampler, the underlying dictionary and the noise can be efficiently predicted with no tuning of any parameters. The performance of the proposed method is compared with state-of-the-art ones and validated on two hyperspectral datasets, which are contaminated with the Gaussian noises, impulse noises, stripes and dead pixel lines, or with a large number of data missing uniformly at random. The visual and quantitative results demonstrate the superiority of the proposed method.
Katsuya NAKAHIRA Jun MASHINO Jun-ichi ABE Daisuke MURAYAMA Tadao NAKAGAWA Takatoshi SUGIYAMA
This paper proposes a dynamic spectrum controlled (DSTC) channel allocation algorithm to increase the total throughput of satellite communication (SATCOM) systems. To effectively use satellite resources such as the satellite's maximum transponder bandwidth and maximum transmission power and to handle the propagation gain variation at all earth stations, the DSTC algorithm uses two new transmission techniques: spectrum compression and spectrum division. The algorithm controls various transmission parameters, such as the spectrum compression ratio, number of spectrum divisions, combination of modulation method and FEC coding rate (MODCOD), transmission power, and spectrum bandwidth to ensure a constant transmission bit rate under variable propagation conditions. Simulation results show that the DSTC algorithm achieves up to 1.6 times higher throughput than a simple MODCOD-based algorithm.
Muhammad Sajjad KHAN Muhammad USMAN Vu-Van HIEP Insoo KOO
Protection of the licensed user (LU) and utilization of the spectrum are the most important goals in cognitive radio networks. To achieve the first goal, a cognitive user (CU) is required to sense for a longer time period, but this adversely affects the second goal, i.e., throughput or utilization of the network, because of the reduced time left for transmission in a time slot. This tradeoff can be controlled by simultaneous sensing and data transmission for the whole frame duration. However, increasing the sensing time to the frame duration consumes more energy. We propose a new frame structure in this paper, in which transmission is done for the whole frame duration whereas sensing is performed only until the required detection probability is satisfied. This means the CU is not required to perform sensing for the whole frame duration, and thus, conserves some energy by sensing for a smaller duration. With the proposed frame structure, throughput of all the CUs is estimated for the frame and, based on the estimated throughput and consumed energy in sensing and transmission, the energy efficient pair of CUs (transmitter and receiver) that maximizes system throughput by consuming less energy, is selected for a time slot. The selected CUs transmits data for the whole time slot, whereas sensing is performed only for certain duration. The performance improvement of the proposed scheme is demonstrated through simulations by comparing it with existing schemes.
Shangqi ZHANG Haihong SHEN Chunlei HUO
Building detection from high resolution remote sensing images is challenging due to the high intraclass variability and the difficulty in describing buildings. To address the above difficulties, a novel approach is proposed based on the combination of shape-specific feature extraction and discriminative feature classification. Shape-specific feature can capture complex shapes and structures of buildings. Discriminative feature classification is effective in reflecting similarities among buildings and differences between buildings and backgrounds. Experiments demonstrate the effectiveness of the proposed approach.
Kazuki HOSOYA Ryo WAKAYAMA Kei OYA Satoru IWAMORI
Active oxygen species (AOS), e.g., excited singlet oxygen atom [O(1D)], excited singlet oxygen molecules (1O2), ground-state oxygen atom [O(3P)] and hydroxyl radical (OH), generated under two wavelengths (185 and 254 nm) of ultraviolet (UV) light were exposed to polyethylene (PE), polypropylene (PP) and polystyrene (PS) sheets. We investigated effects of the AOS exposure on the surface modification of these polymer sheets. Nonwoven sheet was used for the surface modification to eliminate an effect of the UV light irradiation. Although hydrophobicity of the PE and PP surfaces was maintained, the PS was changed into the hydrophilic surface.
One of the major subjects for marine resources development and information processing is how to realize underwater short-range and large-capacity data transmissions. The acoustic wave is an effective carrier and has been used for underwater data transmissions because it has lower attenuation in seawater than the radio wave, and has average propagation distance of about 10km or more. However, along with the imaging of transmission data, the inherent low speed of the acoustic wave makes it cannot and become an ideal carrier for high-speed and large-capacity communications. On the other hand, visible-light wave with wavelength of 400nm-650nm is an ideal carrier, which has received much attention. Its attractive features are high transparency and low attenuation rate in underwater, easily control the propagation direction and range by the visibility, and high data rate and capacity, making it excellent for application in underwater wireless communications. However, visible-light waves in the seawater have the spectral attenuation characteristics due to different marine environment. Therefore, in this paper an underwater optical wireless communication method with adaptation seawater function is considered for seawater turbidity of the spatio-temporal change. Two crucial components in the underwater optical wireless communication system, the light wavelength and the modulation method are controlled using wavelength- and modulation-adaptation techniques, respectively. The effectiveness of the method of the adaptation wavelength is demonstrated in underwater optical image transmissions.
Shiyu REN Zhimin ZENG Caili GUO Xuekang SUN Kun SU
Compressed sensing (CS)-based wideband spectrum sensing approaches have attracted much attention because they release the burden of high signal acquisition costs. However, in CS-based sensing approaches, highly non-linear reconstruction methods are used for spectrum recovery, which require high computational complexity. This letter proposes a two-step compressive wideband sensing algorithm. This algorithm introduces a coarse sensing step to further compress the sub-Nyquist measurements before spectrum recovery in the following compressive fine sensing step, as a result of the significant reduction in computational complexity. Its enabled sufficient condition and computational complexity are analyzed. Even when the sufficient condition is just satisfied, the average reduced ratio of computational complexity can reach 50% compared with directly performing compressive sensing with the excellent algorithm that is used in our fine sensing step.
Yasunari MORI Takayoshi YUMII Yumi ASANO Kyouji DOI Christian N. KOYAMA Yasushi IITSUKA Kazunori TAKAHASHI Motoyuki SATO
This paper presents a prototype of a 3D imaging step-frequency radar system at 10-20GHz suitable for the nondestructive inspection of the walls of wooden houses. Using this prototype, it is possible to obtain data for 3D imaging with a single simple scan and make 3D volume images of braces — broken or not — in the walls of wooden houses using synthetic aperture radar processing. The system is a multistatic radar composed of a one-dimensional array antenna (32 transmitting and 32 receiving antennas, which are resistively loaded printed bowtie antennas) and is able to acquire frequency domain data for all the transmitting and receiving antenna pairs, i.e., 32×32=1024 pairs, in 33ms per position. On the basis of comparisons between two array antenna prototype designs, we investigated the optimal distance between a transmitting array and a receiving array to reduce the direct coupling effect. We produced a prototype multistatic radar system and used it to measure different types of wooden targets in two experiments. In the first experiment, we measured plywood bars behind a decorated gypsum board, simulating a broken wooden brace inside a house wall. In the second experiment, we measured a wooden brace made of Japanese cypress as a target inside a model of a typical (wooden) Japanese house wall. The results of both experiments demonstrate the imaging capability of the radar prototype for nondestructive inspection of the insides of wooden house walls.
Wiennat MONGKULMANN Takahiro OKABE Yoichi SATO
We propose a framework to perform auto-radiometric calibration in photometric stereo methods to estimate surface orientations of an object from a sequence of images taken using a radiometrically uncalibrated camera under varying illumination conditions. Our proposed framework allows the simultaneous estimation of surface normals and radiometric responses, and as a result can avoid cumbersome and time-consuming radiometric calibration. The key idea of our framework is to use the consistency between the irradiance values converted from pixel values by using the inverse response function and those computed from the surface normals. Consequently, a linear optimization problem is formulated to estimate the surface normals and the response function simultaneously. Finally, experiments on both synthetic and real images demonstrate that our framework enables photometric stereo methods to accurately estimate surface normals even when the images are captured using cameras with unknown and nonlinear response functions.
Sen MORIYA Kana KIKUCHI Hiroshi SASANO
In this study, we consider techniques to search for high-rate punctured convolutional code (PCC) encoders using dual code encoders. A low-rate R=1/n convolutional code (CC) has a dual code that is identical to a PCC with rate R=(n-1)/n. This implies that a rate R=1/n convolutional code encoder can assist in searches for high-rate PCC encoders. On the other hand, we can derive a rate R=1/n CC encoder from good PCC encoders with rate R=(n-1)/n using dual code encoders. This paper proposes a method to obtain improved high-rate PCC encoders, using exhaustive search results of PCC encoders with rate R=1/3 original encoders, and dual code encoders. We also show some PCC encoders obtained by searches that utilized our method.
Peng WEI Lilin DAN Yue XIAO Shaoqian LI
High peak-to-average power ratio (PAPR) and spectral leakage are two main problems of orthogonal frequency division multiplexing (OFDM) systems. For alleviating the above problems, this paper proposes a joint model which efficiently suppresses both PAPR and spectral leakage, by combining serial peak cancellation (SPC) and time-domain N-continuous OFDM (TD-NC-OFDM) in an iterative way. Furthermore, we give an analytical expression of the proposed joint model to analyze the mutual effects between SPC and TD-NC-OFDM. Lastly, simulation results also support that the joint optimization model can obtain notable PAPR reduction and sidelobe suppression performance with low implementation cost.
Naoya TATE Tadashi KAWAZOE Shunsuke NAKASHIMA Wataru NOMURA Motoichi OHTSU
In order to realize high-yield speckle modulation, we developed a novel spatial light modulator using zinc oxide single crystal doped with nitrogen ions. The distribution of dopants was optimized to induce characteristic optical functions by applying an annealing method developed by us. The device is driven by a current in the in-plane direction, which induces magnetic fields. These fields strongly interact with the doped material, and the spatial distribution of the refractive index is correspondingly modulated via external control. Using this device, we experimentally demonstrated speckle modulation, and we discuss the quantitative superiority of our approach.