Traditional cellular networks suffer the so-called “cell-edge problem” in which the user throughput is deteriorated because of pathloss and inter-cell (co-channel) interference. Recently, Base Station Cooperation (BSC) was proposed as a solution to the cell-edge problem by alleviating the interference and improving diversity and multiplexing gains at the cell-edge. However, it has minimal impact on cell-inner users and increases the complexity of the network. Moreover, static clustering, which fixes the cooperating cells, suffers from inter-cluster interference at the cluster-edge. In this paper, dynamic fractional cooperation is proposed to realize dynamic clustering in a shared RRU network. In the proposed algorithm, base station cooperation is performed dynamically at cell edges for throughput improvement of users located in these areas. To realize such base station cooperation in large scale cellular networks, coordinated scheduling and distributed dynamic cooperation are introduced. The introduction of coordinated scheduling in BSC multi-user MIMO not only maximizes the performance of BSC for cell-edge users but also reduces computational complexity by performing simple single-cell MIMO for cell-inner users. Furthermore, the proposed dynamic clustering employing shared RRU network realizes efficient transmission at all cell edges by forming cooperative cells dynamically with minimal network complexity. Owing to the combinations of the proposed algorithms, dynamic fractional cooperation achieves high network performance at all areas in the cellular network. Simulation results show that the cell-average and the 5% cell-edge user throughput can be significantly increased in practical cellular network scenarios.

To estimate the field emission current associated with an array of carbon nanowalls (CNWs), the model of the floating rods between anode and cathode plates was proposed. An approximate formula for the enhancement factor was derived, showing that the interwall distance of the CNW array critically affects the field emission. The field enhancement factor was almost one order of magnitude less than that of vertically aligned CNTs. Considering the field emission current density, the field emission can be optimized when the interwall distance is comparable with the wall height. For same separation distance, the macroscopic field strength of the CNW array is almost one order of magnitude higher than that of vertical CNT array to obtain the emission current of 1 mA from the cathode surface of 1 cm2.

In this paper, the performance of a low duty factor (DF) hybrid direct sequence (DS) multiband (MB)-pulsed ultra wideband (UWB) system is evaluated over realistic propagation channels to highlight its capability of interference mitigation. The interference mitigation techniques incorporated in the DS-MB-UWB system is a novel design that includes the utilization of the frequency-agile multiple sub-band configuration and the coexistence-friendly low DF signaling. The system design consists of a Rake type receiver over multipath and multi-user channel in the presence of a coexisting narrowband interferer. The propagation channels are modeled based on actual measurement data. Firstly, by suppressing the power in the particular sub-band coexisting with the narrowband signal, performance degradation due to narrowband interference can be improved. It is observed that by fully suppressing the sub-band affected by the narrowband signal, a typical 1-digit performance improvement (e.g. BER improves from 10-3 to 10-4) can be achieved. Secondly, by employing lower DF signaling, self interference (SI) and multi-user interference (MUI) can be mitigated. It is found that a typical 3 dB improvement is achieved by reducing the DF from 0.5 to 0.04. Together, the sub-band power suppression and low DF signaling are shown to be effective mitigation techniques against environment with the presence of SI, MUI and narrowband interference.

Radio frequency on free-space optical (RoFSO) technology is regarded as a new universal platform for enabling seamless convergence of fiber and FSO communication networks, thus extending broadband connectivity to underserved areas. In this paper, we investigate the performance to characterize the transmission of code division multiple access (CDMA) based wireless signals over RoFSO system using aperture averaging (AA) technique under strong turbulence conditions. An analytical model including a modified carrier-to-noise-plus- interference ratio (CNIR) form and a novel closed-form expression for the bit-error rate (BER) is derived. Unlike earlier work, our model takes into consideration the effect of using the AA technique modeled by the gamma-gamma distribution, the optical noises, the intermodulation distortion term due to the laser diode non-linearity and the multiple interference access. By investigating the impact of AA on our model in the strong turbulence regime, we show that there is a design trade-off between the receiver lens aperture and the number of users to achieve a required CNIR ensuring a substantial scintillation fade reduction. The presented work can be used as baseline for the design and performance evaluation of the RoFSO system's ability to transmit different broadband wireless services signals over turbulent FSO links in real scenarios.

This paper investigates a new method for fusion of scores generated by multiple classification sub-systems that help to further reduce the classification error rate in Spoken Language Recognition (SLR). In recent studies, a variety of effective classification algorithms have been developed for SLR. Hence, it has been a common practice in the National Institute of Standards and Technology (NIST) Language Recognition Evaluations (LREs) to fuse the results from several classification sub-systems to boost the performance of the SLR systems. In this work, we introduce a discriminative performance measure to optimize the performance of the fusion of 7 language classifiers developed as IIR's submission to the 2009 NIST LRE. We present an Error Corrective Fusion (ECF) method in which we iteratively learn the fusion weights to minimize error rate of the fusion system. Experiments conducted on the 2009 NIST LRE corpus demonstrate a significant improvement compared to individual sub-systems. Comparison study is also conducted to show the effectiveness of the ECF method.

In this paper, we propose a quantitative metric of measuring the degree of the visual fatigue in a stereoscopy. To the best of our knowledge, this is the first simplified relative quantitative approach describing visual fatigue value of a stereoscopy. Our experimental result shows that the correlation index of more than 98% is obtained between our Simplified Relative Visual Fatigue (SRVF) model and Mean Opinion Score (MOS).

WSNs (Wireless Sensor Networks) are becoming more widely used in various fields, and localization is a crucial and essential issue for sensor network applications. In this letter, we propose a low-complexity localization mechanism for WSNs that operate in 3D (three-dimensional) space. The basic idea is to use aerial vehicles that are deliberately equipped with anchor nodes. These anchors periodically broadcast beacon signals containing their current locations, and unknown nodes receive these signals as soon as the anchors enter their communication range. We estimate the locations of the unknown nodes based on the proposed scheme that transforms the 3D problem into 2D computations to reduce the complexity of 3D localization. Simulated results show that our approach is an effective scheme for 3D self-positioning in WSNs.

Visibly pushdown automata (VPA), introduced by Alur and Madhusuan in 2004, is a subclass of pushdown automata whose stack behavior is completely determined by the input symbol according to a fixed partition of the input alphabet. Since it was introduced, VPA have been shown to be useful in various contexts, e.g., as specification formalism for verification and as an automaton model for processing XML streams. However, implementation of formal verification based on VPA framework is a challenge. In this paper, we propose on-the-fly algorithms to test universality and inclusion problems of this automata class. In particular, we first present a slight improvement on the upper bound for determinization of VPA. Next, in order to check universality of a nondeterministic VPA, we simultaneously determinize this VPA and apply the P-automata technique to compute a set of reachable configurations of the target determinized VPA. When a rejecting configuration is found, the checking process stops and reports that the original VPA is not universal. Otherwise, if all configurations are accepting, the original VPA is universal. Furthermore, to strengthen the algorithm, we define a partial ordering over transitions of P-automaton, and only minimal transitions are used to incrementally generate the P-automaton. The purpose of this process is to keep the determinization step implicitly for generating reachable configurations as minimum as possible. This improvement helps to reduce not only the size of the P-automaton but also the complexity of the determinization phase. We implement the proposed algorithms in a prototype tool, named VPAchecker. Finally, we conduct experiments on randomly generated VPA. The experimental results show that the proposed method outperforms the standard one by several orders of magnitude.

The interference rejection combining (IRC) receiver, which can suppress inter-cell interference, is effective in improving the cell-edge user throughput. The IRC receiver is typically based on the minimum mean square error (MMSE) criteria, which requires highly accurate channel estimation and covariance matrix estimation that includes the inter-cell interference. This paper investigates the gain from the IRC receiver in terms of the downlink user throughput performance in a multi-cell environment. In the evaluation, to assess the actual gain, the inter-cell interference signals including reference signals from the surrounding 56 cells are generated in the same way as the desired signals, and the channel propagation from all of the cells is explicitly taken into account considering pathloss, shadowing, and multipath fading. The results of simulations that assume the inter-site distance of 500 m, the spatial correlation at the transmitter and the receiver of 0.5, and the numbers of transmitter and receiver antennas of 2 and 2, respectively, show that the IRC receiver improves the cell-edge user throughput (defined as the 5% value in the cumulative distribution function) by approximately 15% compared to the simplified MMSE receiver that approximates the inter-cell interference as AWGN, at the cost of a drop in the average user throughput due to less accurate channel and covariance matrices. Furthermore, we consider dynamic switching between the IRC receiver and the simplified MMSE receiver according to the number of streams and modulation and coding scheme levels. The results show that with dynamic switching, both the cell-edge throughput and average user throughput are improved to the same level as that for the IRC receiver and the simplified MMSE receiver, respectively. Therefore, the best performance can be achieved by employing the dynamic switching in all throughput regions.

In this study, we investigate reference signal (RS) transmission schemes that aim to efficiently support coordinated multi-point (CoMP) transmission by providing improved channel estimation accuracy so that transmission parameters can be appropriately chosen on a cellular network. First, we investigate typical scenarios for transmission parameter selection with the widely used CoMP transmission and precoding schemes aligned with those considered for Long Term Evolution (LTE)-Advanced systems. Second, we investigate an RS transmission scheme that can provide accurate channel estimation even with severe inter-cell interference. Finally, we verify the performance benefit of the investigated scheme by a multi-cell link level evaluation. The results obtained indicate: 1) the investigated scheme improves block error rate performance compared to conventional schemes for fixed modulation and coding schemes (MCSs) allocation with a better precoding control accuracy on the LTE-Advanced system downlink and 2) the investigated scheme provides a throughput performance gain compared to conventional schemes for adaptive MCS allocation and coordinated beamforming.

This paper presents a novel method for reconstructing 3D geometry of camera motion and human-face model from a video sequence. The approach combines the concepts of Powell's line minimization with gradient descent. We adapted the line minimization with bracketing used in Powell's minimization to our method. However, instead of bracketing and searching deep down a direction for the minimum point along that direction as done in their line minimization, we achieve minimization by bracketing and searching for the direction in the bracket which provides a lower energy than the previous iteration. Thus, we do not need a large memory as required by Powell's algorithm. The approach to moving in a better direction is similar to classical gradient descent except that the derivative calculation and a good starting point are not needed. The system's constraints are also used to control the bracketing direction. The reconstructed solution is further improved using the Levenberg Marquardt algorithm. No average face model or known-coordinate markers are needed. Feature points defining the human face are tracked using the active appearance model. Occluded points, even in the case of self occlusion, do not pose a problem. The reconstructed space is normalized where the origin can be arbitrarily placed. To use the obtained reconstruction, one can rescale the computed volume to a known scale and transform the coordinate system to any other desired coordinates. This is relatively easy since the 3D geometry of the facial points and the camera parameters of all frames are explicitly computed. Robustness to noise and lens distortion, and 3D accuracy are also demonstrated. All experiments were conducted with an off-the-shelf digital camera carried by a person walking without using any dolly to demonstrate the robustness and practicality of the method. Our method does not require a large memory or the use of any particular, expensive equipment.

To solve the RFID reader collision problem, a Multi-dimensional Channel Management (MCM) mechanism is proposed. A reader selects an idle channel which has the maximum distance with the used channels. A backoff scheme is used before channel acquisition. The simulation results show MCM has better performance than other mechanisms.

This paper proposes likelihood smoothing techniques to improve decision tree-based acoustic models, where decision trees are used as replacements for Gaussian mixture models to compute the observation likelihoods for a given HMM state in a speech recognition system. Decision trees have a number of advantageous properties, such as not imposing restrictions on the number or types of features, and automatically performing feature selection. This paper describes basic configurations of decision tree-based acoustic models and proposes two methods to improve the robustness of the basic model: DT mixture models and soft decisions for continuous features. Experimental results for the Aurora 2 speech database show that a system using decision trees offers state-of-the-art performance, even without taking advantage of its full potential and soft decisions improve the performance of DT-based acoustic models with 16.8% relative error rate reduction over hard decisions.

This paper proposes a single-carrier transmission method based on an overlap frequency-domain equalizing (FDE) and a coherent averaging. FDE is a block-based equalizing technique using discrete Fourier transform. A cyclic prefix is often used to avoid inter-block interference under multipath channel conditions, which reduces transmission efficiency. An overlap FDE is a technique to avoid the cyclic prefix insertion, but the residual interferences often exist after the FDE processing according to the channel conditions. The method proposed in this paper suppresses the residual interferences by applying a coherent averaging to the FDE outputs and improve the equalization performances. Computer simulation shows the effect of the proposed technique over the multipath channels.

This paper introduces a new dynamic 3D mesh representation that provides 3D animation support of progressive display and drastically reduces the amount of storage space required for 3D animation. The primary purpose of progressive display is to allow viewers to get animation as quickly as possible, rather than having to wait until all data has been downloaded. In other words, this method allows for the simultaneous transmission and playing of 3D animation. Experiments show that coarser 3D animation could be reconstructed with as little as 150 KB of data transferred. Using the sustained transmission of refined operators, viewers feel that resolution approaches that of the original animation. The methods used in this study are based on a compression technique commonly used in 3D animation - clustered principle component analysis, using the linearly independent rules of principle components, so that animation can be stored using smaller amounts of data. This method can be coupled with streaming technology to reconstruct animation through iterative updating. Each principle component is a portion of the streaming data to be stored and transmitted after compression, as well as a refined operator during the animation update process. This paper considers errors and rate-distortion optimization, and introduces weighted progressive transmitting (WPT), using refined sequences from optimized principle components, so that each refinement yields an increase in quality. In other words, with identical data size, this method allows each principle component to reduce allowable error and provide the highest quality 3D animation.

In this paper, a geometric source separation system using nonnegative matrix factorization (NMF) is proposed. The adaptive beamformer is the best method for geometric source separation, but it suffers from a “target signal cancellation” problem in multi-path situations. We modified the HALS-NMF algorithm for decomposition into bases, and developed an interference suppression module in order to cancel the interference bases. A performance comparison between the proposed and subband GSC-RLS algorithm using a MATLAB® simulation was executed; the results show that the proposed system is robust in multi-path situations.

This paper presents an adaptive FFE/DFE receiver with an algorithm that measures the data-dependent jitter. The proposed adaptive algorithm determines the compensation level by measuring the input data-dependent jitter. The adaptive algorithm is combined with a clock and data recovery phase detector. The receiver is fabricated in with 0.13 µm CMOS technology, and the compensation range of equalization is up to 26 dB at 2 GHz. The test chip is verified for a 40 inch FR4 trace and a 53 cm flexible printed circuit channel. The receiver occupies an area of 440 µm 520 µm and has a power dissipation of 49 mW (excluding the I/O buffers) from a 1.2 V supply.

Many scientific applications require efficient variable-precision floating-point arithmetic. This paper presents a special-purpose Very Large Instruction Word (VLIW) architecture for variable precision floating-point arithmetic (VV-Processor) on FPGA. The proposed processor uses a unified hardware structure, equipped with multiple custom variable-precision arithmetic units, to implement various variable-precision algebraic and transcendental functions. The performance is improved through the explicitly parallel technology of VLIW instruction and by dynamically varying the precision of intermediate computation. We take division and exponential function as examples to illustrate the design of variable-precision elementary algorithms in VV-Processor. Finally, we create a prototype of VV-Processor unit on a Xilinx XC6VLX760-2FF1760 FPGA chip. The experimental results show that one VV-Processor unit, running at 253 MHz, outperforms the approach of a software-based library running on an Intel Core i3 530 CPU at 2.93 GHz by a factor of 5X-37X for basic variable-precision arithmetic operations and elementary functions.

An image appearance model called iCAM06 was designed for high dynamic range (HDR) image rendering. The dynamic range of an HDR image needs to be mapped on output devices, which is called tone compression or tone mapping. The iCAM06, the representative HDR rendering algorithm, uses tone compression for image reproduction on the low dynamic range of output devices. However, color saturation reduction occurs during its tone compression process. We propose a saturation correction method using the inverse compensation in order to recover the saturation reduction in the iCAM06. Experimental results show that the proposed method has better performance than the iCAM06 from the viewpoint of saturation accuracy and rendering preference.

Well-crystallized Ba2SiO4:Eu2+ powders were grown on a substrate by the vapor phase reaction between a mixed powder (barium carbonate and europium oxide) and SiO gas. The vaporization of SiO occurs at 1400–1600 from the SiO2 source (or SiO powder) in a reducing atmosphere. The formed SiO gas was transported by 95 vol% Ar - 5 vol% H2 gas and reacted with the raw material powders. The emission intensity of the Ba2SiO4:Eu2 + phosphor synthesized by the new vapor phase technique is about 2.6 times higher than that of a conventional solid-state reaction sample.