We evaluated the transmission performance, including received power and transmission throughput characteristics, in 4×4 single-user multiple-input multiple-output (SU-MIMO) transmission for synchronous time division duplex (TDD) and downlink data channels in comparison with single-input single-output (SISO) transmission in an environment where a local 5G wireless base station was installed on the roof of a research building at our university. Accordingly, for the received power characteristics, the difference between the simulation value, which was based on the ray tracing method, and the experimental value at 32 points in the area was within a maximum difference of approximately 10 dB, and sufficient compliance was obtained. Regarding the transmission throughput versus received power characteristics, after showing a simulation method for evaluating throughput characteristics in MIMO, we compared the results with experimental results. The cumulative distribution function (CDF) of the transmission throughput shows that, at a CDF of 50%, in SISO transmission, the simulated value is approximately 115Mbps, and the experimental value is 105Mbps, within a difference of approximately 10Mbps. By contrast, in MIMO transmission, the simulation value is 380Mbps, and the experimental value is approximately 420Mbps, which is a difference of approximately 40Mbps. It was shown that the received power and transmission throughput characteristics can be predicted with sufficient accuracy by obtaining the delay profile and the system model at each reception point using the both ray tracing and MIMO simulation methods in actual environments.

This paper proposes a novel random access identifier (RAID)-linked receiver beamforming method for time division duplex (TDD)-based random access. When the number of receiver antennas at the base station is large in a massive multiple-input multiple-output (MIMO) scenario, the channel estimation accuracy per receiver antenna at the base station receiver is degraded due to the limited received signal power per antenna from the user terminal. This results in degradation in the receiver beamforming (BF) or antenna diversity combining and active RAID detection. The purpose of the proposed method is to achieve accurate active RAID detection and channel estimation with a reasonable level of computational complexity at the base station receiver. In the proposed method, a unique receiver BF vector applied at the base station is linked to each of the M RAIDs prepared by the system. The user terminal selects an appropriate pair comprising a receiver BF vector and a RAID in advance based on the channel estimation results in the downlink assuming channel reciprocity in a TDD system. Therefore, per-receiver antenna channel estimation for receiver BF is not necessary in the proposed method. Furthermore, in order to utilize fully the knowledge of the channel at the user transmitter, we propose applying transmitter filtering (TF) to the proposed method for effective channel shortening in order to increase the orthogonal preambles for active RAID detection and channel estimation prepared for each RAID. Computer simulation results show that the proposed method greatly improves the accuracy of active RAID detection and channel estimation. This results in lower error rates than that for the conventional method performing channel estimation at each antenna in a massive MIMO environment.

We performed a time dependent percolation analysis of the degradation phenomena in ultra-thin CoFeB/MgO/CoFeB magnetic tunneling junctions. The objective was to understand the microscopic degradation physics of coherent tunneling and the thickness limitation of the MgO barrier. We propose two models: a trap assisted tunneling (TAL) model and a filamentary defect assisted leakage (FAL) model. The correlation between resistance drift behavior and barrier lifetime was then calculated and compared with real data based on these models. The relationship between the resistance drift behavior and barrier lifetime was found to be well explained by the TAL model, the random trap formation in the barrier and the percolation path formation which lead to barrier breakdown. Based on the TAL model, the measured TDDB Weibull slope (β) was smaller than the value estimated by the model. By removing the effect of some initial defects in the barrier, an ultra-thin MgO tunneling barrier in MTJ has the potential for a much better lifetime with a better Weibull slope even at 3ML thickness. This method is rather simple but useful to deeply understand the microscopic degradation physics in dielectric films under TDDB stress.

This paper presents indoor and outdoor experiments that confirm 4-Gbps throughput based on 400-MHz bandwidth transmission when applying carrier aggregation (CA) with 4 component carriers (CCs) and 4-by-4 single-user multiple-in multiple-out multiplexing (MIMO) in the 15-GHz frequency band in the downlink of 5G cellular radio access. A new radio interface with time division duplexing (TDD) and radio access based on orthogonal frequency-division multiple access (OFDMA) is implemented in a 5G testbed to confirm ultra-high speed transmission with low latency. The indoor experiment in an entrance hall shows that the peak throughput is 4.3Gbps in front of the base station (BS) antenna where the reference signal received power (RSRP) is -40dBm although the channel correlation at user equipment (UE) antenna is 0.8. The outdoor experiment in an open-space parking area shows that the peak throughput is 2.8Gbps in front of a BS antenna with a high RSRP although rank 2 is selected due to the high channel correlation. The results also show that the average throughput of 2Gbps is achieved 120m from the BS antenna. In a courtyard enclosed by building walls, 3.6Gbps is achieved in an outdoor-to-outdoor environment with a high RSRP and in an outdoor-to-indoor environment where the RSRP is lower due to the penetration loss of glass windows, but the multipath rich environment contributes to realizing the low channel correlation.

Massive MIMO is widely recognized as an essential technology for 5G. Together with newly allocated spectrum (bandwidth) and network densification (small cells), it is expected to play a key role in coping with the ongoing explosion in data-traffic demand and services. Compared to 4G MIMO technologies, massive MIMO can offer large gains in cell spectral efficiency, which, in combination with small cells and additional bandwidth, can translate into vast gains in throughput per unit area. We briefly overview the most promising TDD and FDD operation modes for massive MIMO, and discuss their potential benefits and challenges considering operation over different tiers and frequency bands. TDD operation is naturally suited to massive MIMO and can offer “massive MIMO” gains, with simple in-cell processing, low overheads and low end-to-end latencies. We also briefly describe some important massive MIMO activities towards 5G, including standardization efforts, system development and experimental trials.

In this paper, we consider a distributed power control scheme that can maximize overall capacity of an interference-limited wireless system in which the same radio resource is spatially reused among different transmitter-receiver pairs. This power control scheme employs a gradient-descent method in each transmitter, which adapts its own transmit power to co-channel interference dynamically to maximize the total weighted sum rate (WSR) of the system over a given interval. The key contribution in this paper is to propose a common feedback channel, over which a backward physical signal is accumulated for computing the gradient of the transmit power in each transmitter, thereby significantly reducing signaling overhead for the distributed power control. We show that the proposed power control scheme can achieve almost 95% of its theoretical upper WSR bound, while outperforming the non-power-controlled system by roughly 63% on average.

This paper investigates an interference mitigation technique for dynamic time division duplex (TDD) based frequency-separated small cell networks in future long term evolution advanced (LTE-A) based wireless access systems. In dynamic TDD, cross-link interference, i.e. evolved node B (eNB)-eNB interference and user equipment (UE)-UE interference, also occur, and eNB-eNB interference in particular significantly degrades the uplink (UL) transmission performance. In order to alleviate the impacts of eNB-eNB interference and to obtain high traffic adaptation gain, we investigate a transmit power control (TPC) based interference mitigation (IM) scheme. In TPC-IM, time-domain subframes are divided into two subframe sets according to whether the cross-link interference can occur or not, and different TPC parameters are applied depending on the type of subframe. To improve of UL signal to interference plus noise power ratio (SINR) in the subframe set with the potential to occur eNB-eNB interference, there are two approaches of UL power boosting and downlink (DL) power reduction. We investigate the adequate combination of these two approaches to avoid an impact of DL performance degradation and increase of UE power consumption. Moreover, we further investigate a combined scheme of the TPC-IM and a cell clustering interference mitigation (CCIM) to avoid the significantly strong cross-link interference from the neighbouring cells. Computer simulation confirms that the proposed TPC-IM scheme can achieve 4.4% and 26.2% gain in the average DL and UL throughputs, respectively, compared to the case without any IM schemes on dynamic TDD. Moreover, when the CCIM is applied to the TPC-IM scheme, 11.6% and 40.3% gain can be achieved in the average DL and UL throughputs, respectively.

In this study, Si(100) surface flattening process was investigated utilizing sacrificial oxidation method to improve Metal--Insulator--Semiconductor (MIS) diode characteristics. By etching of the 100,nm-thick sacrificial oxide formed by thermal oxidation at 1100$^{circ}$C, the surface roughness of Si substrate was reduced. The obtained Root-Mean-Square (RMS) roughness was decreased from 0.15,nm (as-cleaned) to 0.07,nm in the case of sacrificial oxide formed by wet oxidation, while it was 0.10,nm in the case of dry oxidation. Furthermore, time-dependent dielectric breakdown (TDDB) characteristic of Al/SiO$_{2}$(10,nm)/p-Si(100) MIS diode structures was found to be improved by the reduction of Si surface RMS roughness.

To improve metal oxide semiconductor field effect transistors (MOSFET) performance, flat interface between gate insulator and silicon (Si) should be realized. In this paper, the influence of Si surface roughness on electrical characteristics of MOSFET with hafnium oxynitride (HfON) gate insulator formed by electron cyclotron resonance (ECR) plasma sputtering was investigated for the first time. The surface roughness of Si substrate was reduced by Ar/4.9%H2 annealing utilizing conventional rapid thermal annealing (RTA) system. The obtained root-mean-square (RMS) roughness was 0.07nm (without annealed: 0.18nm). The HfON was formed by 2nm-thick HfN deposition followed by the Ar/O2 plasma oxidation. The electrical properties of HfON gate insulator were improved by reducing Si surface roughness. It was found that the current drivability of fabricated nMOSFETs was remarkably increased by reducing Si surface roughness. Furthermore, the reduction of Si surface roughness also leads to decrease of the 1/f noise.

To mitigate the impact of the frequency selectivity of the wireless channel on the initial ranging (IR) process in 802.16 based WiMax systems, several well known pre-equalization techniques applied in the IR are first analyzed in detail, and the optimal pre-equalization scheme is further improved for the IR by overcoming its weaknesses. A numerical simulation shows that the proposed pre-equalization scheme significantly improves the performance of multiuser detection and parameter estimation in the IR process.

In precoded TDD MIMO systems, precoding is done based on the downlink CSI, which can be predicted according to the outdated uplink CSI. This letter proposes a double-scale channel prediction scheme where frame-scale Kalman filters and pilot-symbol-scale AR predictors jointly predict the needed downlink CSI.

This paper deals with two types of capacity allocation schemes, i.e., static and adaptive, for uplink and downlink burst durations in the IEEE 802.16 BE (Best Effort) service. We study QoE (Quality of Experience) enhancement of audio-video IP transmission over the uplink channel with the two capacity allocation schemes. We introduce a piggyback request mechanism for uplink bandwidth requests from subscriber stations to the base station in addition to a random access-based request mechanism. We assess QoE of audio-video streams for four schemes obtained from the combination of the capacity allocation schemes and the bandwidth request mechanisms. We also employ two types of audio-video contents. From the assessment result, we notice that the adaptive allocation scheme is effective for QoE enhancement particularly under heavily loaded conditions because of its efficient usage of OFDM symbols. In addition, the piggyback request mechanism can enhance QoE of audio-video transmission. We also find that the effects of capacity allocation schemes and piggyback request mechanism on QoE change according to the content types.

This paper develops the first prototype hardware for a TDD two-way multi-hop relay network with MIMO network coding. Since conventional wireless multi-hop relay networks have the drawback of low data rate, TDD two-way multi-hop relay networks have been studied as a solution to realize high data rate recently. In these networks, forward and backward streams are spatially multiplexed by using interference cancellation techniques such as MIMO beamforming or MIMO network coding. In this paper, a demonstration system for the TDD two-way multi-hop relay network with MIMO network coding (called 2-way relay network hereafter) is developed using the prototype hardware. In the demonstration system, each transmitter and receiver performs network coded broadcast and MIMO multiple access, respectively. By using the demonstration system, network throughput is measured in an indoor environment to prove the realization and effectiveness of the 2-way relay network. From the results of network throughput, it is found that the 2-way relay network can achieve high network throughput approaching theoretical upper bound even in low average end-to-end SNR area where network throughput of the direct link degrades severely. From these results, the realization and effectiveness of the 2-way relay network can be proved in the real indoor environment.

Joint transmission (JT) in time-division-duplex code-division multiple-access (TDD-CDMA) systems can provide a low peak-to-average power ratio (PAPR) for single paths, but causing a high PAPR in multipath environments. To avoid the high PAPR, we propose a new approach to JT technique by selecting certain paths instead of all paths used in JT processing so that PAPR becomes lower. The path selection proposal involves two methods; path selection by taking certain paths from all paths and by taking paths having path gains above a certain threshold value. To enhance the effectiveness of the proposed techniques, we evaluate a combination of the proposed technique with the clipping technique. We evaluate both PAPR and bit error rate (BER) performance for the proposed techniques and its combination with the clipping technique. We compare the results of the proposed techniques with conventional JT technique and the combination techniques with clipping technique. From the results of computer simulation, we show that the proposed path selection techniques perform low PAPR and good BER performance compared to the conventional JT processing. We also show that the combination of proposed path selection technique and clipping performs low PAPR performance without severe BER degradation compared to the conventional clipping technique.

This letter reveals that whole link reciprocity does not exist in general amplify-and-forward (AF) time division duplex (TDD) relay systems due to the gain matrix. To resolve this problem, a novel gain matrix design method is proposed. Any existing gain matrix design criterion can be adopted in the downlink (uplink) to ensure optimal performance, and the proposed scheme is used in the uplink (downlink), with small adjustment, to keep whole link reciprocity. Simulation results show that, the proposed method can maintain whole link reciprocity without performance loss.

Inter-satellite link (ISL) is an important part of the next generation global navigation satellite system (GNSS). In this paper, key technologies of GNSS ISL ranging and time synchronization are researched. Considering that Ka frequency band is used for ISL, a fixed topology is designed and a new time division duplex (TDD) mode is proposed after analyzing the characteristics of GNSS constellations. A novel method called Non-coherent Dual One-way Measuring (NC-DOWM) is applied to this TDD mode. In addition, relevant mathematical formulas, error models and error compensation are discussed in detail. It is found that the proposed NC-DOWM method for GNSS ISL ranging and time synchronization outperforms the current method for GPS in terms of channel utilization efficiency and measuring precision. Furthermore, the presented method has excellent anti-interference capability and engineering feasibility, which can provide a strong technical support for the ISL of the next generation GNSS.

In this letter, we propose two low complexity algorithms for least square (LS) and minimum mean square error (MMSE) based multi-cell joint channel estimation (MJCE). The algorithm for LS-MJCE achieves the same complexity and mean square error (MSE) performance as the previously proposed most efficient algorithm, while the algorithm for MMSE-MJCE is superior to the conventional ones, in terms of either complexity or MSE performance.

In this paper, we propose an AGC (Automatic Gain Control) algorithm for initial cell search in 3GPP (3rd Generation Partnership Project) LTE (Long Term Evolution) TDD (Time Division Duplex) system. Since the received signal has a large signal power difference between uplink and downlink subframe in wireless communication systems using a TDD scheme, conventional AGC scheme cannot sufficiently adjust the AGC gain because the AGC gain cannot converge fast enough to properly respond. Therefore, conventional AGC scheme leads to increased AGC gain variation, and the received signal will be attenuated by large AGC gain variation. To overcome this limitation, we propose an AGC scheme based on the average amplitude ratio calculation which can not only effectively increase convergence speed of the AGC gain but also maintain the stability of AGC operation in LTE TDD system. Also, it is important for AGC to converge efficiently for the accurate radio frame timing detection during the subsequent initial cell search procedure. Therefore, we also consider the proposed AGC scheme in combination with PSS (Primary Synchronization Signal) detection interface for the first step of initial cell search process in LTE TDD system to obtain both a stable AGC operation and accurate PSS detection performance. By extensive computer simulation in the presence of frequency offset and various channel environments, we verified that the proposed method can obtain a good behavior in terms of demodulation and PSS detection performance in LTE TDD system.

The structure of the nanograting channel MOSFET was optimized by simply rounding the corners of the nanogratings. The current drivabilities of the optimized nanograting channel MOSFETs were enhanced by about 20% and 50% for both n-channel and p-channel MOSFETs, respectively. The mobility changes were analyzed on the basis of channel stress as well as theoretical change of mobilities by various surface orientations. The internal compressive stress of 0.23% was measured in the channel. By suppressing the electric field increase at the corner edge of the nanograting channel to less than 10%, the fabricated rounded nanograting MOSFETs achieved lifetimes of NBTI and TDDB as long as those of conventional planar devices.

Continuously increasing the bandwidth to enhance the capacity is impractical because of the scarcity of spectrum availability. Fortunately, on the basis of the characteristics of the multihop cellular networks (MCNs), a new compact frequency reuse scheme has been proposed to provide higher spectrum utilization efficiency and larger capacity without increasing the cost on network. Base stations (BSs) and relay stations (RSs) could transmit simultaneously on the same frequency according to the compact frequency reuse scheme. In this situation, however, mobile stations (MSs) near the coverage boundary will suffer serious interference and their traffic quality can hardly be guaranteed. In order to mitigate the interference while maintaining high spectrum utilization efficiency, this paper introduces a fractional frequency reuse (FFR) scheme into multihop cellular networks, in which the principle of FFR scheme and characteristics of frequency resources configurations are described, then the transmission (Tx) power consumption of BS and RSs is analyzed. The proposed scheme can both meet the requirement of high traffic load in future cellular system and maximize the benefit by reducing the Tx power consumption. Numerical results demonstrate that the proposed FFR in compact frequency reuse achieves higher cell coverage probability and larger capacity with respect to the conventional schemes.