We examine crossing waveguides with three channels consisting of nonlinear material by means of FD-BPM (Finite Difference Beam Propagation Method). Specifically, we investigate how the insertion of a multimode waveguide into the crossing section of both 13 and 23 structures influences the switching characteristics of output power. We then confirm that these structures can be favorably applied to a wide variety of all-optical devices for integrated optics such as intensity-dependent optical switches, optical power distributors and so on.

A high-density multi-port optical connector that exploits the flexibility of bare optical fibers has been developed for use as an optical interface of a parallel optical interconnection module. In the BF (Bare-Fiber) connector, 24 multimode-fibers are mated by direct physical contact in micro-glass-capillaries with a 250-µm pitch. The buckling forces of the optical fibers themselves secure the physical contact. Optical fiber buckling is investigated theoretically and experimentally. A new design method to optimize the span length l and the longitudinal displacement ΔL for the buckling is also proposed based on the requirements afor optical characteristics, mechanical reliability, and dimensional tolerances, etc. A prototype BF connector with l 10 mm and ΔL of 50 µm was designed and fabricated for multimode fiber connections. This connector provides high optical performance: an average insertion loss of 0.05 dB and a return loss of over 35 dB at 850 nm. The optical performance remained stable after a durability test with ten connection-repetitions.

Extremely small aperture radial line slot antennas (RLSAs) are analyzed by method of moments. At first, the analysis model of cylindrical waveguide in terms of rectangular cavity modes is confirmed for a RLSA with a spiral slot arrangement. The overall VSWR as well as rotational symmetry of the actual structure of RLSAs is predicted for the first time and is confirmed experimentally. Secondly, the minimum diameter of the concentric array RLSA is estimated for which the conventional analysis model of a rectangular waveguide is valid for the design of matching slot pairs at the shorted periphery of the radial waveguide. It is found that the curvature and cylindrical short wall at aperture periphery must be considered in the design and analysis of small RLSAs with the gain lower than about 25 dBi.

This letter addresses how to set SIR targets higher than normally required, in order to mitigate the effect of signal-to-interference ratio (SIR) measurement error included in power control steps. We find that scaling up the SIR targets by 1 dB is conformable to resisting SIR measurement error for code division multiple access (CDMA) mobile systems.

Basic characteristics of a short-ended coplanar waveguide (CPW) resonator of good spurious suppression property is studied. The resonator is loaded with open tubs at its middle position and makes a fully planar structure. The length of the resonator is shortened almost by half and the first spurious resonance goes up to more than 3 times of the fundamental resonant frequency without degradation of unloaded Q(Q0). The origin and property of spurious response is thoroughly investigated to show the advantage and the limit of this configuration. The external Q(Qe) and fundamental resonant frequency of the resonator are also clarified theoretically and experimentally. Using those result, a bandpass filter (BPF) is designed on the basis of the narrow band approximation is realized and its transmission characteristics are examined theoretically and experimentally. The spurious suppression characteristics have been realized by the present filter in accordance with the expectation.

In a DC 50 V/3.3 A circuit, the spatial distributions of the spectral intensities of breaking arcs near the cathode for silver contacts were measured on the contact surfaces of three different shapes: flat and spherical (1 mm radius and 2 mm radius) and the arc temperature and the metal-vapor quantity were calculated from the spectral intensities. The influence of the contact shape on the arc temperature and the metal-vapor quantity were also examined, as well as the arc tracks on the contact surfaces and the gain and loss of the contacts. Findings show the distributions of spectral intensities are non-symmetrical from the beginning to the extinction of the breaking arc for the flat contact: However, they are symmetrical in the latter half of the breaking in spite of the number of breaking arcs and the shape of contact surface for the spherical contact. The relationship between the area of the arc tracks on the cathode and the shape of contact surface is the same as the relationship between the existent areas of measured spectra and the shape of the contact surface. For the spherical contacts, the arc temperature and the metal-vapor quantity are affected a little by the radius of the curved of contact surface and the number of breaking arcs. However, the longer the arc duration, the higher the metal-vapor quantity is in the latter period of the breaking arc. For the flat contacts, the metal-vapor quantity is lower than those for the spherical contacts. The gain and loss of the contacts are less and the arc duration is shorter for the flat contact than for the spherical contact.

To provide users with database-like query interfaces on HTML data, several systems have been developed to extract structures from HTML pages. Among them, tree-like structures and path expressions are the most popular modeling and navigating tools, respectively. Although path expressions are straightforward in representing top-down search patterns, they provide very limited help in representing bottom-up and in-breadth search patterns. In this paper, a lattice model is proposed to store Web data. The model provides an integrated mechanism to store text, linking information, HTML hierarchy, and sequence order of HTML data. By incorporating lattice operators with comprehension syntax, we show that the query language can represent top-down, bottom-up, and in-breadth searching patterns with uniform operators. It will be also shown that lattice comprehensions can represent all operators of path expressions, except Kleen closure.

We study resource allocation strategies in ATM switches, which provide quality of service (QoS) guarantees to individual connections. In order to minimize the cell loss rate over a wide range of traffic characteristics, an efficient allocation strategy is necessary. In this paper we introduce a resource allocation strategy, named TP+WRR (Threshold Pushout + Weighted Round Robin) which can fully utilize the buffer space and the bandwidth. We compare the performance of TP+WRR with two typical resource allocation strategies. An exact queueing analysis based on a Markov model is carried out under bursty traffic sources to evaluate their performance. Our results reveal that TP+WRR considerably improves the cell loss probability over the other strategies considered in this paper, especially when many connections are sharing a link.

The disk allocation problem examined in this paper is finding a method to distribute a Binary Cartesian Product File on multiple disks to maximize parallel disk I/O accesses for partial match retrieval. This problem is known to be NP-hard, and heuristic approaches have been applied to obtain suboptimal solutions. Recently, efficient methods such as Binary Disk Modulo (BDM) and Error Correcting Code (ECC) methods have been proposed along with the restrictions that the number of disks in which files are stored should be a power of 2. In this paper, a new Disk Allocation method based on Genetic Algorithm (DAGA) is proposed. The DAGA does not place restrictions on the number of disks to be applied and it can allocate the disks adaptively by taking into account the data access patterns. Using the schema theory, it is proven that the DAGA can realize a near-optimal solution with high probability. Comparing the quality of solution derived by the DAGA with the General Disk Modulo (GDM), BDM, and ECC methods through the simulation, shows that 1) the DAGA is superior to the GDM method in all the cases and 2) with the restrictions being placed on the number of disks, the average response time of the DAGA is always less than that of the BDM method and greater than that of the ECC method in the absence of data skew and 3) when data skew is considered, the DAGA performs better than or equal to both BDM and ECC methods, even when restrictions on the number of disks are enforced.

This paper describes a way of implementing a conceptual model for temporal data on a commercial object database system. The implemented version is provided as a class library. The library enables applications to handle temporal data. Any application can employ the library because it does not depend on specific applications. Furthermore, we propose an enhanced version of Time Index. The index efficiently processes event queries in particular. These queries search time intervals in which given events are all valid. We also investigate the effectiveness of the enhanced Time Index.

We investigated a radio interferometer for geodetic use that incorporates commercially available fiber-optic links modulated in the radio-frequency range, and a method for compensating for the delay occurring in the links. With this type of radio interferometer, we can perform baseline analysis without the need for estimating the clock difference between observation stations, which causes a relatively large error in the vertical component of the estimated position of the station. Another advantage of the interferometer is utilization of phase delay, which improves the accuracy of delay determination considerably. By analyzing the interferometer's signal-to-noise ratio, we estimated the practicable cable length to be 58.0 km. The results of preliminary experiments with short optical fiber links show that the differences in the cable delays of the fiber-optic links can be compensated for by calibration signals which make a round trip between the analysis station and the observation sites, and that phase delay can be measured successfully.

Object-Oriented database systems (OODBMS) are well known for modeling complex and dynamic application domains. Typically OODBMS have to handle large and complex structured objects whose values and structures can change frequently. Consequently there is a high demand for systems which support temporal and versioning features in both objects (or database population) and schema. This paper presents a mechanism for accessing the temporal versioned objects stored in the database which supports schema versioning. The results shown here can be considered as a value-added extension of our model called TVOO described in detail in [1] and [2]. In contrast to conventional database models, in TVOO objects and classes are not physically discarded from the database after they are modified or deleted. They are time dependent and the history of the changes which occur on them are kept as Version hierarchies. Therefore our model enriches the database environment with temporal and versioning features. Also, an access mechanism which makes it possible to access any object under any schema version is defined in such a way that not only objects created under old versions of schema classes can be accessed from new versions, but also objects created by new schema class versions can be accessed from old versions of the respective class.

This paper gives an overview of research activities on high performance databases in Japan. It focuses on parallel algorithms for relational databases and data mining, parallel approaches for object-oriented databases, and parallel disk systems. Studies surveyed in this paper are carried out mainly by database researchers in Japanese universities under the Grant-in-Aid for Scientific Research (1996-1998).

This paper presents results of subjective assessment of the media synchronization quality in the virtual-time rendering (VTR) media synchronization algorithm. For the assessment, stored voice and video streams were transmitted as two separate transport streams from a source to a destination on various traffic conditions in an experimental system. At the destination, they were output after synchronization control. We subjectively assessed the quality of media synchronization in a systematic way. This paper examines the effects of the difference between methods of recovery from asynchrony on the media synchronization quality. The paper also clarifies the relationships between the subjective and objective performance measures. Furthermore, it examines the effect of the difference in scene between media streams and that of the modification of the target output time on the media synchronization quality.

Peculiar patterns of SiO2 contamination around the periphery of the contact trace caused by silicone vapor under switching at the boundary of 1.6 W were confirmed. For micro relays, the electrical power conditions are restricted to lower level. Therefore, it is important to ascertain the upper limit of the electrical power conditions for normal operation. The peculiar pattern is important as it is recognized as the first stage of the origination of contact failure. Causes of this pattern were discussed from the viewpoints of temperature distribution in the contact trace, molten metallic bridge, micro arc discharge, and supply of silicone vapor with oxygen. It is proposed that during the closing contacts, as maximum Joule heating occurs at the periphery of the true contact area and silicone vapor with oxygen is easily supplied at the periphery, SiO2 grows around the contact trace. For the opening contacts, as the bridge or micro arc appears, silicone vapor with oxygen is supplied only outside of the contacts. Thus SiO2 is formed mainly around the periphery of the trace. Moreover, SiO2 was scattered radially depending on the sputtering of molten metal under rupture of the bridge. Therefore, the peculiar pattern forms as a result.

Internet users have become well acquainted with the World Wide Web (WWW) system, and WWW has become the most significant service on the Internet. In the near future, the importance of large scale hypermedia database systems based on WWW technologies is expected to continue to increace. The present study focuses on the issue of managing hyperlink integrity constraints on WWW like hypermedia database systems. After formally defining path existence constraint definitions(PEDs) using intuitive examples, we apply the notion of PEDs to represent hyperlink integrity constraints. Intuitively, a PED can be used to represent the following integrity constraint. If a reference path exists in a given database, then another corresponding reference path must also exist. An outline of a prototype hypermedia database system, AYATORI, which is based on the proposed model and under development, is also mentioned.

we evaluate the effect of express lots on production dispatching rule scheduling and cost in VLSI manufacturing final test process. In the assignment of express lots, we make comparisons of two rules, First In First Out (FIFO) rule which is widely used and WEIGHT+RPM rule which considers the time required for jig and temperature exchanges, the remaining processing time of the machine in use and the lot waiting time in queue. When using FIFO rule, the test efficiency begins to deteriorate and the test cost per chip begins to increase, if the content of express lots exceeds 15%. Furthermore, for 30% of express lots' content, the number of total processed lots decreases by 19% and the test cost per chip increases by 22% in comparison to the cases including no express lots. For WEIGHT+RPM rule, however, the test efficiency does not deteriorate and the test cost per chip does not increase even if the content of express lots is increased up to 50%. When we use WEIGHT+RPM rule, Express Lots Tolerances (ELTs), defined as the maximum content of express lots which permits the deterioration of the system characteristics by 5%, are about three times as high as ones when using FIFO rule. It is also found that WEIGHT+RPM rule maintains higher ELTs against the changes in the numbers of planned chips and prepared jigs as compared with FIFO rule.

This paper proposes a new cell station (CS) configuration for personal communication systems. The proposed CS employs a modified coherent demodulator with 4-branch maximal ratio combining diversity and a burst-by-burst automatic frequency control (AFC) to enhance the coverage. The proposed CS also employs an antenna-sharing diversity transmission to incorporate more than one transceiver block into a small unit with high power efficiency. With these techniques, the BER performance of the uplink control channel (CCH) is flattened regardless of carrier frequency errors within 12 kHz; the diversity gain of uplink traffic channel (TCH) is improved by 2 dB; the downlink transmission power is reduced by 1.9 dB.

Structured documents often contain character strings of which semantics can be naturally stored as database values or has direct correspondence with database values. By building bilateral logical links between character strings in documents and corresponding database values, semantically rich queries are made expressible. We have introduced a new ADT, named "paratext," to model text which has links with database values. Paratexts are logically viewed as consisting of two parallel layers; on the "appearance" layer, ordinary text (i. e. a linear sequence of character strings) is placed, while the "reference" layer holds an array of OIDs and literals. Each OID or literal on the reference layer is associated with a contiguous substring of the appearance layer text, and represents the semantics of the associated substring. We have also designed domain-specific functions for this document model. Using the functions, we can express queries which go back and forth between the two layers. In structured documents, such character strings can appear in the whole content of logical elements, or as phrases inside logical elements. We also present frameworks for the implementation of the paratext ADT, and discuss how traditional full-text indexing techniques can be extended to support paratext.

In this paper, we will discuss a map synthesis system which handles static information (geographic objects) as well as dynamic information (traffic conditions, weather, etc. ). In addition to geographic thesauruses used in the previous systems, we will use co-existence relationships to improve the quality of maps generation. The system is considered to be general purpose (not restricted to car navigation nor travel maps) and can generate arbitrary maps according to the user's specification. It is very difficult for a user to specify a query which corresponds to the required map, because map description is not easy. The system should automatically generate missing information or find errors in the user specification. For the purpose we use geographic domain thesauruses which contain aggregation and other geographic relationships as well as conventional thesaurus hierarchy. In this paper, we will discuss to use co-existence relationships to enhance ability to select geographic objects automatically. Co-existence specifies relationships among geographic objects which should appear in a map together although they may not have geographic relationship by thesauruses. By utilizing co-existence relationships, a user can acquire much more understandable maps.