A wireless sensor terminal module of 5cc size (2.5 cm × 2.5 cm × 0.8 cm) that does not require a battery is proposed by integrating three kinds of circuit technologies. (i) a low-power sensor interface: an FM modulation type CMOS sensor interface circuit that can operate with a typical power consumption of 24.5 μW was fabricated by the 0.7-μm CMOS process technology. (ii) power supply to the sensor interface circuit: a wireless power transmission characteristic to a small-sized PCB spiral coil antenna was clarified and applied to the module. (iii) wireless sensing from the module: backscatter communication technology that modulates the signal from the base terminal equipment with sensor information and reflects it, which is used for the low-power sensing operation. The module fabricated includes a rectifier circuit with the PCB spiral coil antenna that receives wireless power transmitted from base terminal equipment by electromagnetic resonance coupling and converts it into DC power and a sensor interface circuit that operates using the power. The interface circuit modulates the received signal with the sensor information and reflects it back to the base terminal. The module could achieve 100 mm communication distance when 0.4 mW power is feeding to the sensor terminal.

In this paper, we investigate a wireless-powered relays assisted batteryless IoT network based on the non-linear energy harvesting model, where there exists an energy service provider constituted by the hybrid access point (HAP) and an IoT service provider constituted by multiple clusters. The HAP provides energy signals to the batteryless devices for information backscattering and the wireless-powered relays for energy harvesting. The relays are deployed to assist the batteryless devices with the information transmission to the HAP by using the harvested energy. To model the energy interactions between the energy service provider and IoT service provider, we propose a Stackelberg game based framework. We aim to maximize the respective utility values of the two providers. Since the utility maximization problem of the IoT service provider is non-convex, we employ the fractional programming theory and propose a block coordinate descent (BCD) based algorithm with successive convex approximation (SCA) and semi-definite relaxation (SDR) techniques to solve it. Numerical simulation results confirm that compared to the benchmark schemes, our proposed scheme can achieve larger utility values for both the energy service provider and IoT service provider.

The performance of a fully wireless-power-transfer (WPT) node network, in which each node transfers (and receives) energy through a wireless channel when it has sufficient (and insufficient) energy in its battery, was theoretically analyzed. The lost job ratio (LJR), namely, is the ratio of (i) the amount of jobs that cannot be done due to battery of a node running out to (ii) the amount of jobs that should be done, is used as a performance metric. It describes the effect of the battery of each node running out and how much additional energy is needed. Although it is known that WPT can reduce the probability of the battery running out among a few nodes within a small area, the performance of a fully WPT network has not been clarified. By using stochastic geometry and first-passage-time analysis for a diffusion process, the expected LJR was theoretically derived. Numerical examples demonstrate that the key parameters determining the performance of the network are node density, threshold switching of statuses between “transferring energy” and “receiving energy,” and the parameters of power conversion. They also demonstrate the followings: (1) The mean energy stored in the node battery decreases in the networks because of the loss caused by WPT, and a fully WPT network cannot decrease the probability of the battery running out under the current WPT efficiency. (2) When the saturation value of power conversion increases, a fully WPT network can decrease the probability of the battery running out although the mean energy stored in the node battery still decreases in the networks. This result is explained by the fact that the variance of stored energy in each node battery becomes smaller due to transfer of energy from nodes of sufficient energy to nodes of insufficient energy.

Aiming at the problem of low classification accuracy of surface defects of lithium battery pole pieces by traditional classification methods, an image classification algorithm for surface defects of lithium battery pole piece based on deep learning is proposed in this paper. Firstly, Wavelet Threshold and Histogram Equalization are used to preprocess the detect image to weaken influence of noise in non-defect regions and enhance defect features. Secondly, a VGG-InceptionV2 network with better performance is proposed by adding InceptionV2 structure to the improved VGG network structure. Then the original data set is expanded by rotating, flipping and contrast adjustment, and the optimal value of the model hyperparameters is determined by experiments. Finally, the model in this paper is compared with VGG16 and GoogLeNet to realize the recognition of defect types. The results show that the accuracy rate of the model in this paper for the surface pole piece defects of lithium batteries is 98.75%, and the model parameters is only 1.7M, which has certain significance for the classification of lithium battery surface pole piece defects in industry.

Energy management in buildings is vital for reducing electricity costs and maximizing the comfort of occupants. Excess solar generation can be used by combining a battery storage system and a heating, ventilation, and air-conditioning (HVAC) system so that occupants feel comfortable. Despite several studies on the scheduling of appliances, batteries, and HVAC, comprehensive and time scalable approaches are required that integrate such predictive information as renewable generation and thermal comfort. In this paper, we propose an thermal-comfort aware online co-scheduling framework that incorporates optimal energy scheduling and a prediction model of PV generation and thermal comfort with the model predictive control (MPC) approach. We introduce a photovoltaic (PV) energy nowcasting and thermal-comfort-estimation model that provides useful information for optimization. The energy management problem is formulated as three coordinated optimization problems that cover fast and slow time-scales by considering predicted information. This approach reduces the time complexity without a significant negative impact on the result's global nature and its quality. Experimental results show that our proposed framework achieves optimal energy management that takes into account the trade-off between electricity expenses and thermal comfort. Our sensitivity analysis indicates that introducing a battery significantly improves the trade-off relationship.

In this letter, we propose an energy beamforming empowered relaying scheme for a batteryless IoT network, where wireless-powered relays are deployed between the hybrid access point (HAP) and batteryless IoT devices to assist the uplink information transmission from the devices to the HAP. In particular, the HAP first exploits energy beamforming to efficiently transmit radio frequency (RF) signals to transfer energy to the relays and as the incident signals to enable the information backscattering of batteryless IoT devices. Then, each relay uses the harvested energy to forward the decoded signals from its corresponding batteryless IoT device to the HAP, where the maximum-ratio combing is used for further performance improvement. To maximize the network sum-rate, the joint optimization of energy beamforming vectors at the HAP, network time scheduling, power allocation at the relays, and relection coefficient at the users is investigated. As the formulated problem is non-convex, we propose an alternating optimization algorithm with the variable substitution and semi-definite relaxation (SDR) techniques to solve it efficiently. Specifically, we prove that the obtained energy beamforming matrices are always rank-one. Numerical results show that compared to the benchmark schemes, the proposed scheme can achieve a significant sum-rate gain.

A switching-based Li-ion battery charger without any additional compensation circuit is proposed. The proposed charger adopts a dual-current sensor and a current window control to ensure system stability in different charge modes: trickle current, constant current, and constant voltage. The proposed Li-ion battery charger has less chip area and a simpler structure to design than a conventional Li-ion battery charger with pulse width modulation. Simulation with a 1000µF capacitor as the battery equivalent, a 5V input, and a 1A charge current resulted in a charging time of 1.47ms and a 91% power efficiency.

In an internet of things (IoT) system using an energy harvesting device and a secondary (2nd) battery, regardless of the age of the 2nd battery, the power management shortens the lifespan of the entire system. In this paper, we propose a scheme that extends the lifetime of the energy harvesting-based IoT system equipped with a Lithium 2nd battery. The proposed scheme includes several policies of using a supercapacitor as a primary energy storage, limiting the charging level according to the predicted harvesting energy, swinging the energy level around the minimum stress state of charge (SOC) level, and delaying the charge start time. Experiments with natural solar energy measurements based on a battery aging approximation model show that the proposed method can extend the operation lifetime of an existing IoT system from less than one and a half year to more than four years.

This paper proposes and demonstrates a 65nm CMOS process cascode single-inductor-dual-output (SIDO) boost converter whose outputs are Li-ion battery and 1V low voltage supply for RF wireless power transfer (WPT) receiver. The 1V power supply is used for internal control circuits to reduce power consumption. In order to withstand 4.2V Li-ion battery output, cascode 2.5V I/O PFETs are used at the power stage. On the other hand, to generate 1V while maintaining 4.2V tolerance at 1V output, cascode 2.5V I/O NFETs output stage is proposed. Measurement results show conversion efficiency of 87% at PIN=7mW, ILOAD=1.6mA and VBAT=4.0V, and 89% at PIN=7.9mW, ILOAD=2.1mA and VBAT=3.4V.

The decentralized energy network is one of the promising solutions as a next-generation power grid. In this system, each house has a photovoltaic (PV) panel as a renewable energy source and a battery which is an essential component to balance between generation and demand. The common objective of the battery management on such systems is to minimize only the purchased energy from a power company, but battery degradation caused by charge/discharge cycles is also a serious problem. This paper proposes a State-of-Health (SOH) aware system-level battery management methodology for the decentralized energy network. The power distribution problem is often solved with mixed integer programming (MIP), and the proposed MIP formulation takes into account the SOH model. In order to minimize the purchased energy and reduce the battery degradation simultaneously, the optimization problem is divided into two stages: 1) the purchased energy minimization, and 2) the battery aging factor reducing, and the trade-off exploration between the purchased energy and the battery degradation is available. Experimental results show that the proposed method achieves the better trade-off and reduces the battery aging cost by 14% over the baseline method while keeping the purchased energy minimum.

This new design uses a low power embedded controller (EC) in cooperation with the BIOS of a notebook (NB) computer, both to accomplish dynamic adjustment and to maintain a required performance level of the battery mode of the notebook. In order to extend the operation time at the battery mode, in general, the notebook computer will directly reduce the clock rate and then reduce the performance. This design can obtain the necessary balance of the performance and the power consumption by using both the EC and the BIOS cooperatively to implement the dynamic control of both the CPU and the GPU frequency to maintain the system performance at a sufficient level for a high speed and high resolution video game. In contrast, in order to maintain a certain notebook performance, in terms of battery life it will be necessary to make some trade-offs.

The real-time state-of-health (SOH) estimation of lithium-ion batteries for electric vehicles (EV) is essential to EV maintenance. According to situations in practical applications such as long EV battery capacity test time, unavailability of regular daily tests, and availability of full-life-cycle charge data of EV recorded on the charging facility big data platform, this paper studies an online in-use EV state-of-health estimation method using iterated extended Gaussian process regression-Kalman filter (GPR-EKF) to incorporate lithium-ion battery data at the macro time scale and the micro time scale based on daily charge data of electric vehicles. This method proposes a kernel function GPR (Gaussian process regression) integrating neutral network with cycles to conduct fitting for data at the macro time scale to determine colored measurement noise; in addition, fragment charge data at the micro time scale is adjusted with real-time iteration to be used as the state equation, which effectively addresses issues of real-time SOC calibration and nonlinearization. The pertinence, effectiveness and real-time performance of the model algorithm in online battery state-of-health estimation is verified by actual data.

Recent works on enhancing the comfort and convenience of vehicles have revealed the advantage of various wireless sensor nodes for information collection. For the highly required reliability in vehicles, Reliable Wireless Communication based on Substitute Forwarding (RWCSF) has been proposed. It ensures that 99.999% of communications can finish within 20ms, which is the quality of communication equivalent to wired links. However, the performance was evaluated in very limited situations, where two or more communications never occurred simultaneously and no noise was present. In this paper, we enhance RWCSF to achieve the target communication quality even if two or more communications occur simultaneously. In addition, we evaluate the enhanced method in various types of vehicles that create internal noise.

In this paper, a proof-of-concept sensor platform for an all-in-one wireless bio sensor chip was developed and evaluated. An on-chip battery, an on-chip electrochromic display (ECD), a micro processor, a voltage converter and analog switches were implemented on a printed circuit board. Instead of bio-sensor, a temperature sensor was used to evaluate the functionality of the platform. The platform successfully worked in an electrolyte and the encoded measurement result was displayed on the ECD. The displayed data was captured by a CMOS digital camera and the measured data could be successfully decoded by a computer program.

The present paper proposes a dynamic spectrum access policy for multi-hop cognitive radio networks (CRNs), where the transmission in each hop suffers a delay waiting for the communication channel to become available. Recognizing the energy constraints, we assume that each secondary user (SU) in the network is powered by a battery with finite initial energy. We develop an energy-efficient policy for CRNs using the Markov decision process, which searches for spectrum opportunities without a common communication channel and assigns each sensor's decision to every time slot. We first consider a single-sensor scenario. Due to the intermittent activation of the sensor, achieving the optimal sensing schedule requires excessive complexity and is computationally intractable, owing to the fact that the state space of the Markov decision process evolves exponentially with time variance. In order to overcome this difficulty, we propose a state-reduced suboptimal policy by relaxing the constrained state space, i.e., assuming that the electrical energy of a node is infinite, because this state-reduced suboptimal approach can substantially reduce the complexity of decision-making for CRNs. We then analyze the performance of the proposed policy and compare it with the optimal solution. Furthermore, we verify the performance of this spectrum access policy under real conditions in which the electrical energy of a node is finite. The proposed spectrum access policy uses the dynamic information of each channel. We prove that this schedule is a good approximation for the true optimal schedule, which is impractical to obtain. According to our theoretical analysis, the proposed policy has less complexity but comparable performance. It is proved that when the operating time of the CRN is sufficiently long, the data reception rate on the sink node side will converge to the optimal rate with probability 1. Based on the results for the single-sensor scenario, the proposed schedule is extended to a multi-hop CRN. The proposed schedule can achieve synchronization between transmitter and receiver without relying on a common control channel, and also has near-optimal performance. The performance of the proposed spectrum access policy is confirmed through simulation.

Artificial lighting is responsible for a large portion of total energy consumption and has great potential for energy saving. This paper designs an LED light control algorithm based on users' localization using multiple battery-less binary human detection sensors. The proposed lighting control system focuses on reducing office lighting energy consumption and satisfying users' illumination requirement. Most current lighting control systems use infrared human detection sensors, but the poor detection probability, especially for a static user, makes it difficult to realize comfortable and effective lighting control. To improve the detection probability of each sensor, we proposed to locate sensors as close to each user as possible by using a battery-less wireless sensor network, in which all sensors can be placed freely in the space with high energy stability. We also proposed to use a multi-sensor-based user localization algorithm to capture user's position more accurately and realize fine lighting control which works even with static users. The system is actually implemented in an indoor office environment in a pilot project. A verification experiment is conducted by measuring the practical illumination and power consumption. The performance agrees with design expectations. It shows that the proposed LED lighting control system reduces the energy consumption significantly, 57% compared to the batch control scheme, and satisfies user's illumination requirement with 100% probability.

As the electricity rates during peak hours are higher, this paper proposes a design for an ultrabook to automatically shift the charging period to an off-peak period. In addition, this design sets an upper limit for the battery which thus protects the battery and prevents it from remaining in a continued state of both high temperature and high voltage. This design uses both a low-power embedded controller (EC) and the fuzzy logic controller (FLC) control method as the main control techniques together with real time clock (RTC) ICs. The sensing value of the EC and the presetting of parameters are used to control the conversion of the AC/DC module. This user interface design allows the user to set not only the peak/off-peak period but also the upper use limit of the battery.

This paper empirically validates battery-less sensor activation via wireless energy transmission to release sensors from wires and batteries. To seamlessly extend the coverage and activate sensor nodes distributed in any indoor environment, we proposed multi-point wireless energy transmission with carrier shift diversity. In this scheme, multiple transmitters are employed to compensate path-loss attenuation and orthogonal frequencies are allocated to the multiple transmitters to avoid the destructive interference that occurs when the same frequency is used by all transmitters. In our previous works, the effectiveness of the proposed scheme was validated theoretically and also empirically by using just a spectrum analyzer to measure the received power. In this paper, we develop low-energy battery-less sensor nodes whose consumed power and required received power for activation are respectively 142µW and 400µW. In addition, we conduct indoor experiments in which the received power and activation of battery-less sensor node are simultaneously observed by using the developed battery-less sensor node and a spectrum analyzer. The results show that the coverage of single-point and multi-point wireless energy transmission without carrier shift diversity are, respectively, 84.4% and 83.7%, while the coverage of the proposed scheme is 100%. It can be concluded that the effectiveness of the proposed scheme can be verified by our experiments using real battery-less sensor nodes.

A prompt rescue is a serious operation when a catastrophic disaster occurs. In an uncommunicable area where the existing communication systems are damaged, it is, however, difficult to collect SOS messages of victims. So far, we have proposed a smartphone application named SOSCast to collect SOS messages via device-to-device transmission in such an area. However, with the limitation of coverage area and battery consumption, it decreases the possibility of finding the victim due to the risk of losing the SOS messages. In this paper, thus, we propose an information-sharing cluster to virtually extend the communication coverage area and to secure the SOS messages by reducing the battery consumption. In the performance evaluation, compared with the original SOSCast, we showed that the proposed method can reduce battery consumption to secure the message through a prototype system and simulation experiments.

We report the fabrication of magnetic metallic contaminant detectors using multiple high-Tc SQUIDs (superconducting quantum interference devices) for a lithium-ion battery cathode sheet. Finding ultra-small metallic foreign matter is an important issue for a manufacturer because metallic contaminants carry the risk of an internal short. When contamination occurs, the manufacturer of the product suffers a great loss from recalling the tainted product. Hence, a detection method of small contaminants is required. Preventing such accidents is also an important issue for manufacturers of industrial products. Given the lower detection limit for practical X-ray usage is in the order of 1 mm, a detection system using a SQUID is a more powerful tool for sensitive inspections. We design and set up an eight-channel roll-to-roll high-Tc dc-SQUID inspection system for a lithium ion battery cathode sheet. We report the evaluation results that the detection of a small $arphi $18,-$mu $m steel particle on a lithium-ion battery cathode sheet was successfully done.