In this paper, the uplink performance of Multi-User Multiple Input Multiple Output (MU-MIMO) Zero Forcing (ZF) receiver is investigated over correlated Rayleigh fading channels with channel estimation error. A mathematical expression for the sub-streams' output Signal to Noise Ratio (SNR) with transmit and receive-correlation is derived in the presence of erroneous channel estimates. Besides, an approximate and accurate expression for the Bit Error Rate (BER) of ZF receiver for 16-Quadrature Amplitude Modulation (QAM) with transmit-correlation is deduced in terms of the hypergeometric function. Subsequently, the developed analytical BER is verified by Monte-Carlo trails accounting various system parameters. The simulation results indicate that ZF receiver's BER relies solely on the transmit-correlation for the same number of transmit and receive-antennas at higher average SNR values per transmitted symbol (Es/N0). Also, a logarithmic and exponential growth in the BER is observed with an increase in the Mean Square estimation Error (MSE) and correlation coefficient, respectively.

This paper proposes time division multiplexing (TDM) based reference signal (RS) multiplexing for faster-than-Nyquist (FTN) signaling using orthogonal frequency division multiplexing (OFDM). We also propose a subframe structure in which a cyclic prefix (CP) is appended to only the TDM based RS block and the first FTN symbol to achieve accurate estimation of the channel response in a multipath fading channel with low CP overhead. Computer simulation results show that the loss in the required average received SNR satisfying the average block error rate (BLER) of 10-2 using the proposed TDM based RS multiplexing from that with ideal channel estimation is suppressed to within approximately 1.2dB and 1.7dB for QPSK and 16QAM, respectively. This is compared to when the improvement ratio of the spectral efficiency from CP-OFDM is 1.31 with the rate-1/2 turbo code. We conclude that the TDM based RS multiplexing with the associated CP multiplexing is effective in achieving accurate channel estimation for FTN signaling using OFDM.

This letter expands the previously proposed High Time Resolution Carrier Interferometry (HTRCI) to estimate a larger amount of channel status information (CSI). HTRCI is based on a comb-type pilot symbol on OFDM and CSI for null subcarriers are interpolated by time-domain signal processing. In order to utilize such null pilot subcarriers for increasing estimable CSI, they should generally be separated in frequency-domain prior to estimation and interpolation processes. The main proposal is its separation scheme in conjunction with the HTRCI treatment of the temporal domain. Its effectiveness is verified by a pilot de-contamination on downlink two-cell MIMO transmission scenario. Binary error rate (BER) performance can be improved in comparison to conventional HTRCI and zero padding (ZP) which replaces the impulse response alias with zeros.

This paper presents the bit error rate (BER) performance of frequency domain equalization (FDE) using cyclic-shifted code division multiplexing (CDM) pilot signals for single-carrier line-of-sight (LOS) - multiple-input multiple-output (MIMO) multiplexing. We propose applying different cyclic-shift resources of the same Zadoff-Chu sequence to transmission-stream-specific pilot signals that are essential for estimating the channel response for FDE and phase noise in LOS-MIMO. To validate the effectiveness of the cyclic-shifted pilot multiplexing, we use partial low-density parity-check (LDPC) coding with double Gray mapping and collaborative decoding. Simulations show that pilot signal multiplexing using a cyclic-shifted Zadoff-Chu sequence, and frequency domain averaging of the estimated channel response are effective in achieving accurate channel estimation for single-carrier LOS-MIMO. We also show that the required received signal-to-noise power ratio at the BER of 10-7 using partial LDPC coding is decreased by more than 6.6dB compared to that without LDPC coding even for the deep notch depth of -20dB regardless of the relationship between the notch frequencies in the direct and cross links for 2×2 LOS-MIMO in a Rummler fading channel. Therefore, we conclude that the CDM-based pilot signal multiplexing with different cyclic shifts is effective in accurately estimating the channel response specific to the combination sets of transmitter and receiver antennas and in achieving a low pilot-overhead loss for single-carrier LOS-MIMO.

In this letter, a method for the construction of polar codes based on the mutual information approximation (MIA) is proposed for the 4Tb/in2 two-dimensional inter-symbol interference (2D-ISI) channels, such as the bit-patterned magnetic recording (BPMR) and two-dimensional magnetic recording (TDMR). The basic idea is to exploit the MIA between the input and output of a 2D detector to establish a log-likelihood ratio (LLR) distribution model based on the MIA results, which compensates the gap caused by the 2D ISI channel. Consequently, the polar codes obtained by the optimization techniques previously developed for the additive white Gaussian noise (AWGN) channels can also have satisfactory performances over 2D-ISI channels. Simulated results show that the proposed polar codes can outperform the polar codes constructed by the traditional methods over 4Tb/in2 2D-ISI channels.

Cache prefetching technique brings huge benefits to performance improvement, but it comes at the cost of microarchitectural security in processors. In this letter, we deep dive into internal workings of a DCUIP prefetcher, which is one of prefetchers equipped in Intel processors. We discover that a DCUIP table is shared among different execution contexts in hyperthreading-enabled processors, which leads to another microarchitectural vulnerability. By exploiting the vulnerability, we propose a DCUIP poisoning attack. We demonstrate an AES encryption key can be extracted from an AES-NI implementation by mounting the proposed attack.

In this letter, we investigate tight analytical and asymptotic upper bounds for bit error rate (BER) of constitutional codes over exponentially correlated Nakagami-m fading channels. Specifically, we derive the BER expression depending on an exact closed-form formula for pairwise error event probabilities (PEEP). Moreover, the corresponding asymptotic analysis in high signal-to-noise ratio (SNR) regime is also explored, which is verified via numerical results. This allows us to have explicit insights on the achievable coding gain and diversity order.

Image dehazing is of great significance in computer vision and other fields. The performance of dehazing mainly relies on the precise computation of transmission map. However, the computation of the existing transmission map still does not work well in the sky area and is easily influenced by noise. Hence, the dark channel prior (DCP) and luminance model are used to estimate the coarse transmission in this work, which can deal with the problem of transmission estimation in the sky area. Then a novel weighted variational regularization model is proposed to refine the transmission. Specifically, the proposed model can simultaneously refine the transmittance and restore clear images, yielding a haze-free image. More importantly, the proposed model can preserve the important image details and suppress image noise in the dehazing process. In addition, a new Gaussian Adaptive Weighted function is defined to smooth the contextual areas while preserving the depth discontinuity edges. Experiments on real-world and synthetic images illustrate that our method has a rival advantage with the state-of-art algorithms in different hazy environments.

Wireless Mesh Networks (WMNs) are often designed on IEEE 802.11 standards and are being widely studied due to their adaptability in practical network scenarios, where the overall performance has been improved by the use of the Multi-Radio and Multi-Channel (MRMC) configuration. However, because of the limitation on the number of available orthogonal channels and radios on each router, the network still suffers from low throughput due to packet collisions. Many studies have demonstrated that the optimized channel assignment to radio interfaces so as to avoid interference among wireless links is an effective solution. However, no existing channel assignment scheme can achieve hidden-terminal-free transmission and thus avoid communication performance degradation given the limited number of orthogonal channels. In this paper, we propose a new static channel assignment scheme CASCA (CSMA-aware Static Channel Assignment) based on a Partial MAX-SAT formulation of the channel assignment problem that incorporates a CSMA-aware interference model. The evaluation results show that CASCA achieves hidden-terminal-freedom in both grid and random topology networks with 3-4 orthogonal channels with preservation of network connectivity. In addition, the network simulation results show that CASCA presents good communication performance with low MAC-layer collision rate.

In this paper, we explore the physical layer security of an Internet of Things (IoT) network comprised of multiple relay-user pairs in the presence of multiple malicious eavesdroppers and channel estimation error (CEE). In order to guarantee secure transmission with channel estimation error, we propose a channel estimation error oriented joint relay-user pair and friendly jammer selection (CEE-JRUPaFJS) scheme to improve the physical layer security of IoT networks. For the purpose of comparison, the channel estimation error oriented traditional round-robin (CEE-TRR) scheme and the channel estimation error oriented traditional pure relay-user pair selection (CEE-TPRUPS) scheme are considered as benchmark schemes. The exact closed-form expressions of outage probability (OP) and intercept probability (IP) for the CEE-TRR and CEE-TPRUPS schemes as well as the CEE-JRUPaFJS scheme are derived over Rayleigh fading channels, which are employed to characterize network reliability and security, respectively. Moreover, the security-reliability tradeoff (SRT) is analyzed as a metric to evaluate the tradeoff performance of CEE-JRUPaFJS scheme. It is verified that the proposed CEE-JRUPaFJS scheme is superior to both the CEE-TRR and CEE-TPRUPS schemes in terms of SRT, which demonstrates our proposed CEE-JRUPaFJS scheme are capable of improving the security and reliability performance of IoT networks in the face of multiple eavesdroppers. Moreover, as the number of relay-user pairs increases, CEE-TPRUPS and CEE-JRUPaFJS schemes offer significant increases in SRT. Conversely, with an increasing number of eavesdroppers, the SRT of all these three schemes become worse.

This paper proposes a novel radio access scheme that uses duplicated transmission via multiple frequency channels to achieve mission critical Internet of Things (IoT) services requiring highly reliable wireless communications; the interference constraints that yield the required reliability are revealed. To achieve mission critical IoT services by wireless communication, it is necessary to improve reliability in addition to satisfying the required transmission delay time. Reliability is defined as the packet arrival rate without exceeding the desired transmission delay time. Traffic of the own system and interference from the other systems using the same frequency channel such as unlicensed bands degrades the reliability. One solution is the frequency/time diversity technique. However, these techniques may not achieve the required reliability because of the time taken to achieve the correct reception. This paper proposes a novel scheme that transmits duplicate packets utilizing multiple wireless interfaces over multiple frequency channels. It also proposes a suppressed duplicate transmission (SDT) scheme, which prevents the wastage of radio resources. The proposed scheme achieves the same reliable performance as the conventional scheme but has higher tolerance against interference than retransmission. We evaluate the relationship between the reliability and the occupation time ratio where the interference occupation time ratio is defined as the usage ratio of the frequency resources occupied by the other systems. We reveal the upper bound of the interference occupation time ratio for each frequency channel, which is needed if channel selection control is to achieve the required reliability.

Currently, the IEEE 802.11n wireless local-area network (WLAN) has been extensively deployed world-wide. For the efficient channel assignment to access-points (APs) from the limited number of partially overlapping channels (POCs) at 2.4GHz band, we have studied the throughput drop estimation model for concurrently communicating links using the channel bonding (CB). However, non-CB links should be used in dense WLANs, since the CB links often reduce the transmission capacity due to high interferences from other links. In this paper, we examine the throughput drop estimation model for concurrently communicating links without using the CB in 802.11n WLAN, and its application to the POC assignment to the APs. First, we verify the model accuracy through experiments in two network fields. The results show that the average error is 9.946% and 6.285% for the high and low interference case respectively. Then, we verify the effectiveness of the POC assignment to the APs using the model through simulations and experiments. The results show that the model improves the smallest throughput of a host by 22.195% and the total throughput of all the hosts by 22.196% on average in simulations for three large topologies, and the total throughput by 12.89% on average in experiments for two small topologies.

With the widespread diffusion of Internet of Things (IoT), the number of applications using wireless sensor devices are increasing, and Quality of Service (QoS) required for these applications is diversifying. Thus, it becomes difficult to satisfy a variety of QoS with a single wireless system, and many kinds of wireless systems are working in the same domains; time, frequency, and place. This paper considers coexistence environments of ZigBee and Wi-Fi networks, which use the same frequency band channels, in the same place. In such coexistence environments,ZigBee devices suffer radio interference from Wi-Fi networks, which results in severe ZigBee packet losses because the transmission power of Wi-Fi is much higher than that of ZigBee. Many existing methods to avoid interference from Wi-Fi networks focus on only one of time, frequency, or space domain. However, such avoidance in one domain is insufficient particularly in near future IoT environments where more ZigBee devices and Wi-Fi stations transfer more amount of data. Therefore, in this paper, we propose joint channel allocation and routing in both frequency and space domains. Finally, we show the effectiveness of the proposed method by computer simulation.

Inter-channel crosstalk is one of the limiting factors in multichannel optical systems. This paper presents a theoretical analysis of the bit-error-rate (BER) performance of quadrature phase shift keying (QPSK) and quadrature amplitude modulation (QAM) signals influenced by multiple crosstalk channels. The field distribution of multiple crosstalk channels in the constellation map is calculated. The BER of the QPSK/QAM signal, onto which the crosstalk light is superimposed, is then evaluated for a varying number of crosstalk channels under the condition that the total crosstalk power is constant. The results quantitatively confirm that as the channel number increases, the BER degradation caused by crosstalk light approaches that caused by Gaussian noise light. It is also confirmed that the degradations caused by crosstalk light and Gaussian light are similar for QAM signals of high-level modulation.

Channel modeling is a vital step in designing transceivers for wireless implant communication systems due to the extremely challenging environment of the human body. In this paper, the in-to-on body path loss and group delay were first analyzed using an electric dipole and a current loop in the 10-60MHz human body communication band. A path loss model was derived using finite difference time domain (FDTD) simulation and an anatomical human body model. As a result, it was found that the path loss increases with distance in an exponent of 5.6 for dipole and 3.9 for loop, and the group delay variation is within 1ns for both dipole and loop which suggests a flat phase response. Moreover, the electric and magnetic field distributions revealed that the magnetic field components dominate in-body signal transmission in this frequency band. Based on the analysis results of the implant channel, the link budget was analyzed. An experiment on a prototype transceiver was also performed to validate the path loss model and bit error rate (BER) performance. The experimentally derived path loss exponent was between the electric dipole path loss exponent and the current loop path loss exponent, and the BER measurement showed the feasibility of 20Mbps implant communication up to a body depth of at least 15cm.

Sparse modeling is one of the most active research areas in engineering and science. The technique provides solutions from far fewer samples exploiting sparsity, that is, the majority of the data are zero. This paper reviews sparse modeling in radio techniques. The first half of this paper introduces direction-of-arrival (DOA) estimation from signals received by multiple antennas. The estimation is carried out using compressed sensing, an effective tool for the sparse modeling, which produces solutions to an underdetermined linear system with a sparse regularization term. The DOA estimation performance is compared among three compressed sensing algorithms. The second half reviews channel state information (CSI) acquisitions in multiple-input multiple-output (MIMO) systems. In time-varying environments, CSI estimated with pilot symbols may be outdated at the actual transmission time. We describe CSI prediction based on sparse DOA estimation, and show excellent precoding performance when using the CSI prediction. The other topic in the second half is sparse Bayesian learning (SBL)-based channel estimation. A base station (BS) has many antennas in a massive MIMO system. A major obstacle for using the massive MIMO system in frequency-division duplex mode is an overhead for downlink CSI acquisition because we need to send many pilot symbols from the BS and to get the feedback from user equipment. An SBL-based channel estimation method can mitigate this issue. In this paper, we describe the outline of the method, and show that the technique can reduce the downlink pilot symbols.

In this paper, we propose a real-time BSS (Blind Source Separation) system with two microphones that extracts only desired sound sources. Under the assumption that the desired sound sources are close to the microphones, the proposed BSS system suppresses distant sound sources as undesired sound sources. We previously developed a BSS system that can estimate the distance from a microphone to a sound source and suppress distant sound sources, but it was not a real-time processing system. The proposed BSS system is a real-time version of our previous BSS system. To develop the proposed BSS system, we simplify some BSS procedures of the previous system. Simulation results showed that the proposed system can effectively suppress the distant source signals in real-time and has almost the same capability as the previous system.

Side-channel (SC) leakage from a cryptographic device chip is simulated as the dynamic current flowing out of the chip. When evaluating the simulated current, an evaluation by comparison with an actual measurement is essential; however, it is difficult to compare them directly. This is because a measured waveform is typically the output voltage of probe placed at the observation position outside the chip, and the actual dynamic current is modified by several transfer impedances. Therefore, in this paper, the probe voltage is converted into the dynamic current by using an EMC macro-model of a cryptographic device being evaluated. This paper shows that both the amplitude and the SC analysis (correlation power analysis and measurements to disclosure) results of the simulated dynamic current were evaluated appropriately by using the EMC macro-model. An evaluation confirms that the shape of the simulated current matches the measured one; moreover, the SC analysis results agreed with the measured ones well. On the basis of the results, it is confirmed that a register-transfer level (RTL) simulation of the dynamic current gives a reasonable estimation of SC traces.

This paper proposes a novel weight derivation method to improve adaptive array interference suppression performance based on our previously conceived sample matrix inversion algorithm using common correlation matrix (CCM-SMI), by data-aided approach. In recent broadband wireless communication system such as orthogonal frequency division multiplexing (OFDM) which possesses lots of subcarriers, the computation complexity is serious problem when using SMI algorithm to suppress unknown interference. To resolve this problem, CCM based SMI algorithm was previously proposed. It computes the correlation matrix by the received time domain signals before fast Fourier transform (FFT). However, due to the limited number of pilot symbols, the estimated channel state information (CSI) is often incorrect. It leads limited interference suppression performance. In this paper, we newly employ a data-aided channel state estimation. Decision results of received symbols are obtained by CCM-SMI and then fed-back to the channel estimator. It assists improving CSI estimation accuracy. Computer simulation result reveals that our proposal accomplishes better bit error rate (BER) performance in spite of the minimum pilot symbols with a slight additional computation complexity.

We propose an iterative single-image haze-removal method that first divides images with haze into regions in which haze-removal processing is difficult and then estimates the ambient light. The existing method has a problem wherein it often overestimates the amount of haze in regions where there is a large distance between the location the photograph was taken and the subject of the photograph; this problem prevents the ambient light from being estimated accurately. In particular, it is often difficult to accurately estimate the ambient light of images containing white and sky regions. Processing those regions in the same way as other regions has detrimental results, such as darkness or unnecessary color change. The proposed method divides such regions in advance into multiple small regions, and then, the ambient light is estimated from the small regions in which haze removal is easy to process. We evaluated the proposed method through some simulations, and found that the method achieves better haze reduction accuracy even than the state-of-the art methods based on deep learning.