We propose a simple and scalable scheduler called Elapsing Time-based Priority (ETP) scheduler for the optical burst switch (OBS) control channel; it eliminates the requirements of global synchronization and core-state information. This scheduler reduces edge-to-edge delays of burst control packets and total latencies of data bursts.
Yong-Hwa KIM Jong-Ho LEE Seong-Cheol KIM
A carrier frequency synchronization scheme is proposed for orthogonal frequency-division multiplexing (OFDM) systems in the presence of phase noise (PHN). In the proposed scheme, carrier frequency synchronization is performed based on the maximum-likelihood (ML) algorithm using an OFDM preamble symbol. The proposed scheme is compared with conventional methods. Simulation results are presented to illustrate the effectiveness of the proposed scheme in the presence of PHN.
Shun-ichiro OHMI Tetsushi SAKAI
Twin-Channel (TC)-MOSFET with twin omega-gate (Ω-gate) Si channels and its fabrication process were proposed. The twin Si channels are able to be fabricated by self-aligned process utilizing wet etching of SiN and silicon-on-insulator (SOI) wafers. Three-dimensional (3-D) device simulation was performed to optimize gate structure for TC-MOSFET with 10 nm10 nm (TSiWG) channels with the gate length of 30 nm, and it was found that TC-MOSFET with right-angled Ω-gate in case the Lunder was 3 nm showed excellent device characteristics similar to the gate-all-around (GAA) devices corresponding to the gate structure as Lunder=5 nm. Fabrication process of twin Si channels was also investigated experimentally, and approximately 40 nm40 nm twin Si channels were successfully fabricated on SOI by the proposed fabrication process.
Ye Hoon LEE Seokho YOON Sun Yong KIM
In this paper, we propose an adaptive data transmission scheme for DS/CDMA packet radio communication systems in bandlimited indoor multipath fading channels. We first analyze the relationship between the code rate and the processing gain (defined as the number of chips per coded bit) in maximizing the normalized throughput in connection with the channel state of the indoor multipath fading channels. One observation made is that the maximum throughput with BPSK modulation is attained when the code rate is chosen as low as possible irrespective of the channel state, and the processing gain is increased (decreased) as the channel becomes worse (better). The other observation made is that when DPSK modulation is employed, there exists an optimal combination of the code rate and the processing gain in maximizing the normalized throughput for each channel state. Based on these observations, we propose to adapt the processing gain and/or code rate according to the fading conditions in order to maximize the normalized throughput. We analyze the performance of the proposed scheme and compare it with the non-adaptive data transmission scheme. Our results show that the adaptive transmission scheme yields a significant performance improvement over the nonadaptive scheme, and increasing the adaptation level is more effective as the channel gets worse, but the 3-state adaptation seems to be practically optimum.
Xiao Peng YANG Qiang CHEN Kunio SAWAYA
A numerical hybrid method for analyzing the wireless channel of Multiple-Input Multiple-Output (MIMO) communication system is proposed by combining of the method of moments (MoM) and the finite difference time domain (FDTD) method. The proposed method is capable of investigating a more practical MIMO wireless channel than the conventional methods, and CPU time is much less than that of the FDTD method in analysis of spatial statistical characteristics of received signals. Based on the channel transfer matrix obtained by the proposed method, the wall effect on indoor MIMO channel capacity are investigated with consideration of received power, Ricean K-factor and effective degrees of freedom (EDOF) of multipaths by changing the wall locations and material.
Abdullah AL AMIN Kenji SAKURAI Tomonari SHIODA Masakazu SUGIYAMA Yoshiaki NAKANO
An 8ch, 400 GHz monolithically integrated WDM channel selector featuring an array of quantum well semiconductor optical amplifiers (SOA) and arrayed waveguidegrating demultiplexer is presented. Reduction of fabrication complexity was achieved by using a single step selective area MOVPE to realize the different bandgap profiles for the SOA array and passive region. The selective growth mask dimensions were optimized by simulation. Dry-etching with short bending radii of 200 µm resulted in compact device size of 7 mm2.5 mm. Static channel selection with high ON-OFF ratio of >40 dB was achieved.
Koichi ISHIHARA Kazuaki TAKEDA Fumiyuki ADACHI
As the channel frequency selectivity becomes severer, the bit error rate (BER) performance of direct sequence spread spectrum (DSSS) signal transmission with rake combining degrades due to an increasing inter-path interference (IPI). Frequency-domain equalization (FDE) can replace rake combining with much improved BER performance in a severe frequency-selective fading channel. For FDE, accurate estimation of the channel transfer function is required. In this paper, we propose an iterative channel estimation that uses pilot chips which are time-multiplexed within each chip block for fast Fourier transform (FFT). The pilot acts as a cyclic-prefix of FFT block as well. The achievable BER performance is evaluated by computer simulation. It is shown that the proposed channel estimation has a very good tracking ability against fast fading.
We present the approximated bit error rate (BER) performance of a binary phase shift keying (BPSK) modulated equal-gain combining (EGC) diversity receiver with phase noise over independent and non-identical Nakagami fading branches. The approximated BER becomes accurate with phase-locked loop (PLL) gain, K=20. Also, for special values of fading parameter, m, and branch number, L, we derived the closed form expression of the BER.
Yukisato NOGAMI Toshifumi SATOH Hiroyuki TANGO
A two-dimensional (2-D) physical model of n-channel poly-Si LDD TFTs in comparison with that of SD TFTs is presented to analyze hot-carrier degradation. The model is based on 2-D device simulator's Gaussian doping profiles for the source and drain junctions fitted to the lateral and vertical impurity profiles in poly-Si obtained from a 2-D process simulator. We have shown that, in the current saturation bias (Vg
Kazunari YOKOMAKURA Seiichi SAMPEI Hiroshi HARADA Norihiko MORINAGA
This paper proposes a channel estimation technique for the dynamic parameter controlled--orthogonal frequency and time division multiple access (DPC-OF/TDMA) systems studied as one of the candidates of the beyond third generation (B3G) systems. In the proposed scheme, the impulse response, which represents the channel state information (CSI) is estimated using carrier interferometry (CI) which is equivalent to impulse signal transmission. Moreover, because the minimum number of subcarriers allocated to terminals is 64, in order to estimate a CSI with its spreading factor of 64, we employ a code-multiplexed CI signal for a cell search process and a time-domain-multiplexed CI signal for transmit antenna identification. Furthermore, we also propose a flexible CSI estimation scheme that supports two cases: multiple subchannel block assignment and MIMO transmission cases. Computer simulation confirms that the proposed scheme can estimate the CSI with high accuracy.
Yusuke ASAI Wenjie JIANG Takeshi ONIZAWA Atsushi OHTA Satoru AIKAWA
This paper proposes a simple and feasible decision-feedback channel tracking scheme for multiple-input multiple-output orthogonal frequency division multiplexing (MIMO-OFDM) systems designed for wireless local area networks (LANs). In the proposed scheme, the channel state matrix for each subcarrier is tentatively estimated from a replica matrix of the transmitted signals. The estimated channel matrices, each derived at a different timing, are combined, and the previously estimated channel matrices are replaced with the latest ones. Unlike conventional channel tracking schemes based on a Kalman filter, the proposed scheme needs no statistical information about a MIMO channel, which makes the receiver structure quite simple. The packet error rate (PER) performances for the proposed scheme are evaluated on computer simulations. When there are three transmit and receive antennas, the subcarrier modulation scheme is 64 QAM, and the coding rate is 3/4, the proposed scheme keeps the SNR degradation at PER of 1e-2 less than 0.1 dB when the velocity of receiver is 3 km/h in an indoor office environment at 5 GHz band. In addition, compared to the conventional channel tracking scheme based on known pilot symbols, the proposed scheme improves throughput performance by 13.8% because it does not need pilot symbols. These results demonstrate that the proposed channel tracking scheme is simple and feasible for implementation in MIMO-OFDM systems based on wireless LANs.
Jigang QIU Yi LONG Xiang CHEN Xiaokang LIN
In this paper a multi-channel MAC protocol with dynamic channel allocation (MMAC-DCA) in CDMA Ad Hoc networks is proposed. Under MMAC-DCA, the service sub-channels are dynamically allocated by the RTS/CTS dialogue on the common sub-channel, only when a node has a packet to transmit. In addition, a Markov mode is presented to analyze the performance of MMAC-DCA.
Suguru SUGAWARA Eisuke KUDOH Fumiyuki ADACHI
In DS-CDMA cellular communications systems, the single frequency reuse can be utilized. Since large other-cell interference is produced, the well known soft handover or site diversity must be used. If the single frequency reuse is not utilized to avoid the other-cell interference, we will face the frequency allocation problem, similar to FDMA systems. In this paper, a DS-CDMA cellular system using band division is proposed. The available wide frequency band is divided into several narrow frequency bands and the different frequency bands are allocated to adjacent cells so as to avoid the large other-cell interference. For the frequency allocation, the channel segregation distributed channel allocation (CS-DCA) algorithm is applied. The link capacity is evaluated by computer simulation.
Hiroki IURA Hiroyoshi YAMADA Yasutaka OGAWA Yoshio YAMAGUCHI
Antenna array is essential factor for multiple- input multiple-output (MIMO) wireless systems. Since the antenna array is composed of closely spaced elements, the mutual coupling among the elements cannot be ignored for the best performance of the array. Mutual coupling affects the MIMO channel, so the performance of a MIMO system, including channel capacity and diversity, varies with the degree of mutual coupling. The effect of mutual coupling is a function of the antenna load impedance. Therefore, designing an optimal element-matched array for a MIMO system requires consideration of the optimal matching condition for the array elements, the one that maximizes the channel capacity. We evaluated the effects of mutual coupling with various matching conditions in dipole arrays, and investigated their effects on the path correlation and channel capacity of MIMO systems. Simulation showed that the conventional conjugate matching of each element is still suitable for closely spaced elements except when the separation is about less than 0.1λ. Theoretical consideration of the received power of a closely-spaced-element array is also provided to show the effects of mutual coupling.
Qiang LI Jiansong GAN Yunzhou LI Shidong ZHOU Yan YAO
Spatial multiplexing (SM) offers a linear increase in transmission rate without bandwidth expansion or power increase. In SM systems, the LMMSE receiver establishes a good tradeoff between the complexity and performance. The performance of the LMMSE receiver would be degraded by MIMO channel estimation errors. This letter focus on obtaining the asymptotic convergence of output interference power and SIR performance for the LMMSE receiver with channel uncertainty. Exactly matched simulation results verify the validity of analysis in the large-system assumption. Furthermore, we find that the analytical results are also valid in the sense of average results for limited-scale system in spite of the asymptotic assumption used in derivation.
Terng-Ren HSU Chien-Ching LIN Terng-Yin HSU Chen-Yi LEE
For more efficient data transmissions, a new MLP/BP-based channel equalizer is proposed to compensate for multi-path fading in wireless applications. In this work, for better system performance, we apply the soft output and the soft feedback structure as well as the soft decision channel decoding. Moreover, to improve packet error rate (PER) and bit error rate (BER), we search for the optimal scaling factor of the transfer function in the output layer of the MLP/BP neural networks and add small random disturbances to the training data. As compared with the conventional MLP/BP-based DFEs and the soft output MLP/BP-based DFEs, the proposed MLP/BP-based soft DFEs under multi-path fading channels can improve over 3-0.6 dB at PER=10-1 and over 3.3-0.8 dB at BER=10-3.
Lan TANG Pengcheng ZHU Jingyu HUA Xiaohu YOU
Since the accuracy of channel prediction influences the performance of adaptive multiple-input-multiple-output (MIMO) systems in Rayleigh fading channels, we analyze the performance of adaptive V-BLAST systems with a minimum-mean-square-error (MMSE) channel predictor in this paper. Considering the channel prediction error, we obtain the closed-form expressions for the bit-error-rate (BER) and throughput of adaptive V-BLAST systems, and maximize system transmission rate by choosing optimum block length under BER constraint. The numerical results reveal the critical value of channel prediction error below which systems can match the transmission rate of the systems with perfect channel prediction.
Hiromichi TOMEBA Kazuaki TAKEDA Fumiyuki ADACHI
Recently, we proposed space-time block coded-joint transmit/receive antenna diversity (STBC-JTRD) for narrow band transmission in a frequency-nonselective fading channel; it allows an arbitrary number of transmit antennas while limiting the number of receive antennas to 4. In this paper, we extend STBC-JTRD to the case of frequency-selective fading channels and propose frequency-domain STBC-JTRD for broadband direct sequence-spread spectrum (DSSS) signal transmission. A conditional bit error rate (BER) analysis is presented. The average BER performance in a frequency-selective Rayleigh fading is evaluated by Monte-Carlo numerical computation method using the derived conditional BER and is confirmed by computer simulation of the signal transmission. Performance comparison between frequency-domain STBC-JTRD transmission and joint space-time transmit diversity (STTD) and frequency-domain equalization (FDE) reception is also presented.
Satoshi GOUNAI Tomoaki OHTSUKI Toshinobu KANEKO
Irregular LDPC codes can achieve better error rate performance than regular LDPC codes. However, irregular LDPC codes have higher error floors than regular LDPC codes. The Ordered Statistic Decoding (OSD) algorithm achieves approximate Maximum Likelihood (ML) decoding. ML decoding is effective to lower error floors. However, the OSD estimates satisfy the parity check equation of the LDPC code even the estimates are wrong. Hybrid decoder combining LLR-BP decoding algorithm and the OSD algorithm cannot also lower error floors, because wrong estimates also satisfy the LDPC parity check equation. We proposed the concatenated code constructed with an inner irregular LDPC code and an outer Cyclic Redundancy Check (CRC). Owing to CRC, we can detect wrong codewords from OSD estimates. Our CRC-LDPC code with hybrid decoder can lower error floors in an AWGN channel. In wireless communications, we cannot neglect the effects of the channel. The OSD algorithm needs the ordering of each bit based on the reliability. The Channel State Information (CSI) is used for deciding reliability of each bit. In this paper, we evaluate the Block Error Rate (BLER) of the CRC-LDPC code with hybrid decoder in a fast fading channel with perfect and imperfect CSIs where 'imperfect CSI' means that the distribution of channel and those statistical average of the fading amplitudes are known at the receiver. By computer simulation, we show that the CRC-LDPC code with hybrid decoder can lower error floors than the conventional LDPC code with hybrid decoder in the fast fading channel with perfect and imperfect CSIs. We also show that combining error detection with the OSD algorithm is effective not only for lowering the error floor but also for reducing computational complexity of the OSD algorithm.
Jongkyung KIM Sangjin LEE Jongsoo SEO
We propose a new cyclic postfix based orthogonal frequency division multiplexing (OFDM) system. The proposed system shows superior performance in symbol time synchronization while achieving channel estimation performance comparable to that of conventional cyclic prefix based OFDM system. In the proposed system, an identical postfix is generated at the end of each OFDM symbol by inserting pilot values amongst the data symbols in a frequency domain and performing Inverse Fast Fourier Transform (IFFT) operation on it. Robust time synchronization is achieved by auto- and cross-correlating the postfix. Also, time or frequency domain channel estimation can be realized by using properly designed postfix according to channel estimation method.