The data dispersion of the measurement of electromagnetic disturbance above 1 GHz is mainly affected by site imperfections (expressed by the site voltage standing wave ratio (SVSWR)). To confirm the relationship between site imperfections and the measured field strength, we measured the SVSWR and the field strength radiated from the equipment under test (EUT) by changing the area covered by the RF absorber on the metal ground plane. From the results, we found that the data dispersion of measured field strength can be estimated from the measured SVSWR, and therefore, we can determine the measurement uncertainty of the measured field strength at the test site.

This paper describes a black-box model of mixed analog-digital VLSI circuits for the prediction of microcontroller electromagnetic emissions without disclosure of manufacturer data. The model is based on small-signal simulations performed at the analog and digital building-block level, considering also layout and technology parameters, and modeling the parasitic substrate coupling paths and the interconnects. The developed model allows system designers to predict the impact of microcontroller operation on the system-level EMEs by carrying out low-time consuming simulations in the early design phases of their products thus minimizing unnecessary costs and scheduling delays. In this paper, the black-box model of an 8-bit microcontroller is described and it is employed to predict the conducted emission delivered through the input-output ports.

A novel approach is proposed for miniaturizing the unit cell size of electromagnetic bandgap (EBG) structures that suppress power plane noise. In this approach, open stubs are introduced into the shunt circuits of these EBG structures. Since the stub length determines the resonant frequencies of the shunt circuit, the proposed structures can maintain the bandgaps at lower frequencies without increasing the unit cell size. The bandgap frequencies were estimated by dispersion analysis based on the Bloch theorem and full-wave simulations. Sample boards of the proposed EBG structures were fabricated with a unit cell size of 2.1 mm. Highly suppressed noise propagation over the estimated frequency range of 1.9-3.6 GHz including the 2.4-GHz wireless-LAN band was experimentally demonstrated.

We propose a novel short-range wireless communications technology that uses quasi-static electric fields; it enables data communication between devices separated by up to 10 cm via dielectric media at a speed of 10 Mbps. It is considered to be a secure wireless technology since communication area is restricted to below about 10 cm. To suppress electromagnetic radiation, we adopted a baseband transmission scheme in which the quasi-static electric field is directly modulated by 10 BASE-T data signals. Since the spectra of the data signals are concentrated to below 20 MHz, the amplitude of the electric field rapidly decreases outside the communication area. This contributes to enhancing security of the communications system. In this paper, we explain a basic principle of the short-range wireless communications technology. Since baseband data signals are carried by the quasi-static electric field, the quality of the communication is easily degraded by the existence of the earth ground. To isolate the communications system from the earth ground, we introduce a novel electro-optic sensor to receive the quasi-static electric field. With the electro-optic sensor, stable data communication is possible at 10 Mbps via dielectric materials, such as a wooden table.

Radar cross sections of polygonal cylinders are investigated by using a kind of mode matching methods. Applying two types of novel field-decomposition techniques, electromagnetic scattering analysis can be performed very precisely. We will discuss computational accuracy of our proposed method and the proper choice of field-decomposition techniques for a rectangular cylinder with various shapes of wedge cavities and bumps.

This paper presents the field uniformity characteristics in a triangular prism reverberation chamber that can be substituted for an open area test site or an anechoic chamber to measure electromagnetic interference. To improve size problems of a stirrer that is an official unit to generate a uniform field in the reverberation chamber, we suggest a diffuser of Quadratic Residue Sequence method. To validate the substitution of a diffuser for a stirrer, a diffuser is designed for 1-3 GHz, and three types of equilateral triangular prism reverberation chambers are modeled. Afterwards, the field distributions in these three reverberation chambers are both simulated and tested. Using XFDTD 6.2 of finite difference time domain method, field deviations of each structure are simulated and compared to each other. An evaluation of field uniformity is done by cumulative probability distribution which is specified in the IEC 61000-4-21. The result shows that the field uniformity in the chamber is within 6 dB tolerance and also within 3 dB standard deviation, which means a diffuser can satisfy the requirement of international standards.

This paper proposes two types of electromagnetic bandgap (EBG) structures aimed for SAR reduction on a mobile phone antenna. The EBG structures, one which uses vias while the other does not can reduce the surface wave and prevent the undesired radiation from the antenna. Thus, these structures can reduce the electromagnetic fields toward the human head direction and reduction the SAR value. Tests demonstrate the reduction of SAR values and therefore, the human body can be protected from hazard electromagnetic fields by using the proposed EBG structures, regardless of whether vias are used or not.

The attenuation effect of the walls of a building on the electromagnetic (EM) field generated by an indoor power line communication (PLC) system is numerically investigated using the finite integration (FI) method. In particular, we focus on the frequency range 2-6 MHz, for which the attenuation effect has not yet been sufficiently analyzed. We model a single, finite-sized wall instead of an entire house, to focus on the dependence of the EM field on the wall structure and also reduce the computational resources required. The EM field strength is evaluated at many points on a view plane 10 m from the wall model, and the results are statistically processed to determine the attenuation effect of the wall. We show that the leakage of an EM field at 2-6 MHz is suppressed by about 30 dB by a reinforced concrete wall. We also show that the main contributor to the attenuation effect is the rebar in the wall. We then investigate the relation between the attenuation effect of a single-wall model and that of a house model. The results show that the attenuation effect of a house model is almost the same as that of a 15-m-wall model. We conclude that the use of a single-wall model instead of a house model is effective in determining the attenuation of the EM leakage. This simple structure reduces analytic space, time, and memory in the evaluation of the dependence on the wall structure of the EM leakage from indoor PLC systems.

The purpose of this paper is to investigate the possible impact of cellular phones' signals on implantable cardiac pacemakers in elevators. This is achieved by carrying out precise numerical simulations based on the Finite-Difference-Time-Domain method to examine the electromagnetic fields in elevator models. In order to examine the realistic and complicated situations where humans are present in the elevator, we apply the realistic homogeneous human phantom and cellular radios operating in the frequency bands 800 MHz, 1.5 GHz and 2 GHz. These computed results of field strength inside the elevator are compared with a certain reference level determined from the experimentally obtained maximum interference distance of implantable cardiac pacemakers. This enables us to carry out a quantitative evaluation of the EMI risk to pacemakers by cellular radio transmission. The results show that for the case when up to 5 mobile radio users are present in the elevator model used, there is no likelihood of pacemaker malfunction for the frequency bands 800 MHz, 1.5 GHz and 2 GHz.

Using the transient current switch circuit in parallel with the energizing switching contacts for timely control of breaking operation, the increase of contact voltage is suppressed at the last stage of the breaking of electric contacts. Breaking contact voltage Vc and current Ic of electromagnetic relays with Ag contacting electrodes were measured with 12.5-50 V and 0.1-20 A for two hinge springs (Spring constants; 2 N/mm and 0.2 N/mm). The current-decreasing process was clearly measured at the melting voltage Um. After Vc=Um, the breaking time of contact current did not depend on mechanical motion controlled by the two hinge springs and energizing power-supply voltage, but depended on the contact current. The residue of melt electrode was observed optically as a white fusion spot, with radius depending on the energizing current.

The cooperative characteristics of electromagnetic relay's attraction torque and reaction torque are the key property to ensure its reliability, and it is important to attain better cooperative characteristics by analyzing and optimizing relay's electromagnetic system and mechanical system. From the standpoint of changing reaction torque of mechanical system, in this paper, adjusted parameters (armature's maximum angular displacement αarm_max, initial return spring's force Finiti_return_spring, normally closed (NC) contacts' force FNC_contacts, contacts' gap δgap, and normally opened (NO) contacts' over travel δNO_contacts) were adopted as design variables, and objective function was provided for with the purpose of increasing breaking velocities of both NC contacts and NO contacts. Finally, genetic algorithm (GA) was used to attain optimization of the objective function. Accuracy of calculation for the relay's dynamic characteristics was verified by experiment.

Using the transient current switch circuit in parallel with the energizing contacts, the slow decay of the contact current due to thermal fusion of metal was observed just after the contact voltage exceeded the melting contact voltage Um. At that time, the contact voltage was higher than the boiling contact voltage Ub. These results contradict Holm's θ theory. A new melting model of breaking mechanical contact is proposed. The area surrounding a cluster of contacting a-spots melts, the melt metal diffuses, and the contact spot thermally shrinks. Including the metal phase transition from solid to liquid, the increase of contact resistance is introduced to the electric circuit analysis. The numerical analysis agrees qualitatively with measured V-I characteristics.

An electromagnetic relay (EMR) is widely used in automatic control field, and its dynamic characteristics play a significant role in EMR researches. According to structural features of the EMR, a dynamic characteristics testing and analyzing system (DCTAS) based on CCD digital image processing technique is designed and implemented. By using the DCTAS, the dynamic characteristics (include displacement, velocity, acceleration and force characteristics) of EMR whose operating time is less than 12 ms and armature travel is less than 10 mm can be investigated. The comparison of testing data obtained by the DCTAS and that of by a high speed camera indicates the validity of the system to EMR dynamic characteristics testing.

In this paper, a novel method of partially placing electromagnetic band-gap (EBG) unit cells on both the power and ground planes in multi-layer PCBs and packages is proposed; it can not only sufficiently eliminate simultaneous switching noise (SSN), but also prevent severe degradation of signal quality in high-speed systems with imperfect reference planes resulting from the perforated structures of uni-planar EBG unit cells. On the assumption that the noise sources and noise-sensitive devices exist only in specific areas, the proposed method partially arranges the EBG unit cells on both the power and ground planes, but only around the critical areas. The SSN suppression performance of the proposed structure is verified by a simulation and measurements.

This paper describes an analysis of the effects of electric field on nerve cells by using the Hodgkin-Huxley model. When evaluating our model, which combines an additional ionic current source and generated membrane potential, we derive the peak-to-peak value, the accumulated square of variation, and Kolmogorov-Sinai (KS) entropy of the cell-membrane potential excited by 10, 100, 1 k, and 10 kHz-sinusoidal electric fields. In addition, to obtain a comprehensive view of the time-variation patterns of our model, we used a self-organizing map, which provides a way to map high-dimensional data onto a low-dimensional domain. Simulation results confirmed that lower-frequency electric fields tended to increase fluctuations of the cell-membrane potential, and the additional ionic current source was a more dominant factor for fluctuations of the cell-membrane potential. On the basis of our model, we visually confirmed that the obtained data could be projected onto the map in accordance with responses of cell-membrane potential excited by electric fields, resulting in a combined depiction of the effects of KS entropy and other parameters.

To build a stable power distribution network for high-speed digital systems, simultaneous switching noise (SSN) should be sufficiently suppressed in multi-layer PCBs and packages. In this paper, a novel hybrid uni-planar compact electromagnetic bandgap (UC-EBG) with two triangular-type unit cells designed on power/ground planes is proposed for the ultra-broadband suppression of SSN. The SSN suppression performance of the proposed structure is validated both numerically and experimentally. A -35 dB suppression bandwidth for SSN is achieved, starting at 800 MHz and extending to 15 GHz and beyond, thereby covering almost the entire noise band.

Printed circuit boards (PCBs) driven by a connected feed cable are considered to be one of the main sources of the electromagnetic interference (EMI) from electronic devices. In this paper, a method for predicting the electromagnetic (EM) radiation from a PCB driven by a connected feed cable at up to gigahertz frequencies is proposed and demonstrated. The predictive model is based on the transmission line theory and current- and voltage-driven CM generation mechanisms with consideration of antenna impedance. Frequency responses of differential-mode (DM) and common-mode (CM) currents and far-electric field were investigated experimentally and with finite-difference time-domain (FDTD) modeling. First, the dominant component in total EM radiation from the PCB was identified by using the Source-Path-Antenna model. Although CM can dominate the total radiation at lower frequencies, DM is the dominant component above 3 GHz. Second, the method for predicting CM component at lower frequencies is proposed. And its validity was discussed by comparing FDTD calculated and measured results. Specifically, the relationship between the CM current and the terminating resistor was focused as important consequence for the prediction. Good agreement between the measured and predicted results shows the validity of the predicted results. The proposed model can predict CM current with sufficient accuracy, and also identify the primary coupling-mechanism of CM generation. Then far-electric field was predicted by using the proposed method, and it was demonstrated that outline of the frequency response of the undesired EM radiation from the PCB driven by the connected feed cable can be predicted with engineering accuracy (within 6 dB) up to 18 GHz. Finally, as example of application of equivalent circuit model to EMC design, effect of the width of the ground plane was predicted and discussed. The equivalent circuit model provides enough flexibility for different geometrical parameters and increases our ability to provide insights and design guidelines.

A transmission line created by cables adjoined by connectors is influenced by noise from connectors with contact failure, and such noise degrades communication quality. The authors used a model of a connector with increased contact resistance in a coaxial cable and measured the electromagnetic near-field around a cable while changing positions of the model. In this paper, the result shows that the radiated electromagnetic field has no relationship with the position along the cable of a connector with increased contact resistance, when the contact condition of connector, contact resistance value, measurement position, and length of a transmission line are constant.

The observed phenomena in actual sound and electromagnetic environment are inevitably contaminated by the background noise of arbitrary distribution type. Therefore, in order to evaluate sound and electromagnetic environment, it is necessary to establish some signal processing methods to remove the undesirable effects of the background noise. In this paper, we propose noise cancellation methods for estimating a specific signal with the existence of background noise of non-Gaussian distribution from two viewpoins of static and dynamic signal processing. By applying the well-known least mean squared method for the moment statistics with several orders, practical methods for estimating the specific signal are derived. The effectiveness of the proposed theoretical methods is experimentally confirmed by applying them to estimation problems in actual sound and magnetic field environment.

An inverse scattering problem of estimating the reflection coefficient and the surface impedance from two sets of absolute values of the near field with periodic change is investigated. The problem is formulated in terms of a nonlinear simultaneous equations which is derived from the relation between the two sets of absolute values and the field defined by a finite summation of the modal functions by applying the Fourier analysis. The reflection coefficient is estimated by solving the equations by Newton's method through the successive algorithm with the increment of the number of truncation in the summation one after another. Numerical examples are given and the accuracy of the estimation is discussed.