This paper proposes an accurate and efficient method to calculate probability distributions of pulse-shaped complex signals. We show that the distribution over the in-phase and quadrature-phase (I/Q) complex plane is obtained by a recursive probability mass function of the accumulator for a pulse-shaping filter. In contrast to existing analytical methods, the proposed method provides complex-plane distributions in addition to instantaneous power distributions. Since digital signal processing generally deals with complex amplitude rather than power, the complex-plane distributions are more useful when considering digital signal processing. In addition, our approach is free from the derivation of signal-dependent functions. This fact results in its easy application to arbitrary constellations and pulse-shaping filters like Monte Carlo simulations. Since the proposed method works without numerical integrals and calculations of transcendental functions, the accuracy degradation caused by floating-point arithmetic is inherently reduced. Even though our method is faster than Monte Carlo simulations, the obtained distributions are more accurate. These features of the proposed method realize a novel framework for evaluating the characteristics of pulse-shaped signals, leading to new modulation, predistortion and peak-to-average power ratio (PAPR) reduction schemes.

Quadrature voltage-controlled oscillators (VCOs) with current-weight-average and voltage-weight-average phase-adjusting architectures are studied. The phase adjusting equalizes the oscillation frequency to the LC-resonant frequency. The merits of the equalization are explained by using Leeson's phase noise equation and the impulse sensitivity function (ISF). Quadrature VCOs with the phase-adjusting architectures are fabricated using 180-nm TSMC CMOS and show low-phase-noise performances compared to a conventional differential VCO. The ISF analysis and small-signal analysis also show that the drawbacks of the current-weight-average phase-adjusting and voltage-weight-average phase-adjusting architectures are current-source noise effect and large additional capacitance, respectively. A voltage-average-adjusting circuit with a source follower at its input alleviates the capacitance increase.

Exponential growth in data volumes has promoted widespread interest in data-selective adaptive algorithms. In a pioneering work, Diniz developed the data-selective least mean square (DS-LMS) algorithm, which is able to reduce specific quantities of computation data without compromising performance. Note however that the existing framework fails to consider the issue of impulse noise (IN), which can greatly undermine the benefits of reduced computation. In this letter, we present an error-based IN detection algorithm for implementation in conjunction with the DS-LMS algorithm. Numerical evaluations confirm the effectiveness of our proposed IN-tolerant DS-LMS algorithm.

Recent trends in designing filters involve development of sparse filters with coefficients that not only have real but also zero values. These sparse filters can achieve a high performance through optimizing the selection of the zero coefficients and computing the real (non-zero) coefficients. Designing an infinite impulse response (IIR) sparse filter is more challenging than designing a finite impulse response (FIR) sparse filter. Therefore, studies on the design of IIR sparse filters have been rare. In this study, we consider IIR filters whose coefficients involve zero value, called sparse IIR filter. First, we formulate the design problem as a linear programing problem without imposing any stability condition. Subsequently, we reformulate the design problem by altering the error function and prepare several possible denominator polynomials with stable poles. Finally, by incorporating these methods into successive thinning algorithms, we develop a new design algorithm for the filters. To demonstrate the effectiveness of the proposed method, its performance is compared with that of other existing methods.

In this paper, we propose a robust parameters estimation algorithm for channel coded systems based on the low-density parity-check (LDPC) code over fading channels with impulse noise. The estimated parameters are then used to generate bit log-likelihood ratios (LLRs) for a soft-inputLDPC decoder. The expectation-maximization (EM) algorithm is used to estimate the parameters, including the channel gain and the parameters of the Bernoulli-Gaussian (B-G) impulse noise model. The parameters can be estimated accurately and the average number of iterations of the proposed algorithm is acceptable. Simulation results show that over a wide range of impulse noise power, the proposed algorithm approaches the optimal performance under different Rician channel factors and even under Middleton class-A (M-CA) impulse noise models.

This paper presents two ultra-low voltage and high performance VCO ICs with two novel transformer-based harmonic tuned tanks. The first proposed harmonic tuned tank effectively shapes the pseudo-square drain-node voltage waveform for close-in phase noise reduction. To compensate the voltage drop caused by the transformer, an improved second tank is proposed. It not only has tuned harmonic impedance but also provides a voltage gain to enlarge the output voltage swing over supply voltage limitation. The VCO with second tank exhibits over 3 dB better phase noise performance in 1/f2 region among all tuning range. The two VCO ICs are designed, fabricated and measured on wafer in 45-nm SOI CMOS technology. With only 0.3 V supply voltage, the proposed two VCO ICs exhibit best phase noise of -123.3 and -127.2 dBc/Hz at 10 MHz offset and related FoMs of -191.7 and -192.2 dBc/Hz, respectively. The frequency tuning ranges of them are from 14.05 to 15.14 GHz and from 14.23 to 15.68 GHz, respectively.

Although the classical vector median filter (VMF) has been widely used to suppress the impulse noise in the color image, many thin color curve pixels aligned in arbitrary directions are usually removed out as impulse noise. This serious problem can be solved by the proposed method that can protect the thin curves in arbitrary direction in color image and remove out the impulse noise at the same time. Firstly, samples in the 3x3 filter window are considered to preliminarily detect whether the center pixel is corrupted by impulse noise or not. Then, samples outside a 5x5 filter window are conditionally and partly considered to accurately distinguish the impulse noise and the noise-free pixel. At last, based on the previous outputs, samples on the processed positions in a 3x3 filter window are chosen as the samples of VMF operation to suppress the impulse noise. Extensive experimental results indicate that the proposed algorithm can be used to remove the impulse noise of color image while protecting the thin curves in arbitrary directions.

This paper reviews our developed wide band human body communication technology for wearable and implantable robot control. The wearable and implantable robots are assumed to be controlled by myoelectric signals and operate according to the operator's will. The signal transmission for wearable robot control was shown to be mainly realized by electrostatic coupling, and the signal transmission for implantable robot control was shown to be mainly determined by the lossy frequency-dependent dielectric properties of human body. Based on these basic observations on signal transmission mechanisms, we developed a 10-50MHz band impulse radio transceiver based on human body communication technology, and applied it for wireless control of a robotic hand using myoelectric signals in the first time. In addition, we also examined its applicability to implantable robot control, and evaluated the communication performance of implant signal transmission using a living swine. These experimental results showed that the proposed technology is well suited for detection and transmission of biological signals for wearable and implantable robot control.

Because of its high throughput potentiality on short-range communications and inherent superiority of high precision on ranging and localization, ultra-wideband (UWB) technology has been attracting attention continuously in research and development (R&D) as well as in commercialization. The first domestic regulation admitting indoor UWB in Japan was released by the Ministry of Internal Affairs and Communications (MIC) in 2006. Since then, several revisions have been made in conjunction with UWB commercial penetration, emerging new trends of industrial demands, and coexistence evaluation with other wireless systems. However, it was not until May 2019 that MIC released a new revision to admit outdoor UWB. Meanwhile, the IEEE 802 LAN/MAN Standards Committee has been developing several UWB related standards or amendments accordingly for supporting different use cases. At the time when this paper is submitted, a new amendment known as IEEE 802.15.4z is undergoing drafting procedure which is expected to enhance ranging ability for impulse radio UWB (IR-UWB). In this paper, we first review the domestic UWB regulation and some of its revisions to get a picture of the domestic regulation transition from indoor to outdoor. We also foresee some anticipating changes in future revisions. Then, we overview several published IEEE 802 standards or amendments that are related to IR-UWB. Some features of IEEE 802.15.4z in drafting are also extracted from open materials. Finally, we show with our recent research results that time bias internal a transceiver becomes important for increasing localization accuracy.

For the impulse noise removal from a digital image, most of existing methods cannot repair line structures in an input image. In this letter, a method which considers the local line structure is proposed. In order to judge the direction of the line structure, adjacent lines are considered. The effectiveness of the proposed filter is shown by experiments.

This paper presents a novel delta-sigma modulator that uses a switched-capacitor (SC) integrator with the structure of a finite impulse response (FIR) filter in a loop filter configuration. The delta-sigma analog-to-digital converter (ΔΣADC) is used in various conversion systems to enable low-power, high-accuracy conversion using oversampling and noise shaping. Increasing the gain coefficient of the integrator in the loop filter configuration of the ΔΣADC suppresses the quantization noise that occurs in the signal band. However, there is a trade-off relationship between the integrator gain coefficient and system stability. The SC integrator, which contains an FIR filter, can suppress quantization noise in the signal band without requiring an additional operational amplifier. Additionally, it can realize a higher signal-to-quantization noise ratio. In addition, the poles that are added by the FIR filter structure can improve the system's stability. It is also possible to improve the flexibility of the pole placement in the system. Therefore, a noise transfer function that does not contain a large gain peak is realized. This results in a stable system operation. This paper presents the essential design aspects of a ΔΣADC with an FIR filter. Two types of simulation results are examined for the proposed first- and second-order, and these results confirm the effectiveness of the proposed architecture.

Digitization of analog terrestrial TV broadcasting has recently been accelerated in many countries, and the effective utilization of vacant frequencies has also been investigated for new systems in each country. In Japan, a portion of vacant frequencies in the VHF-high band was allocated to the public broadband mobile communication (PBB) system. To evaluate the current PBB system and develop future broadband communication systems in this band, it is important to analyze the propagation channel more accurately. In this study, we characterize the propagation channel for 200MHz band broadband mobile communication systems, using measured channel impulse responses (CIRs). In the characterization process, the Saleh-Valenzuela (S-V) model is utilized to extract channel model parameters statistically. When evaluating the fluctuation of path power gain, we also propose to model the fluctuation of path power gain using the generalized extreme value distribution instead of the conventional log-normal distribution. The extracted CIR model parameters are validated by cumulative distribution function of root-means-square delay spread and maximum excess delay, comparing simulation result to measurement result. From the extracted CIR model parameters, we clarified the characteristics of 200MHz band broadband mobile communication systems in non-line-of-sight environments based on S-V model with the proposed channel model.

We have proposed and developed new electro-optic modulators for the pre-equalization of signal distortion caused by the optical fiber chromatic dispersion effect. We found that the synthesis of an almost arbitrary impulse response function is obtainable by utilizing an electro-optic modulator composed of a Mach-Zehnder waveguide and travelling-wave electrodes on a ferro-electric material substrate with polarization-reversed structures. In this paper, the operational principle, design and simulation results of the pre-equalization modulator are presented. Some preliminary experimental results are also shown with future prospects.

In this paper, we introduce a new method to remove random-valued impulse noise in an image. Random-valued impulse noise replaces the pixel value at a random position by a random value. Due to the randomness of the noisy pixel values, it is difficult to detect them by comparison with neighboring pixels, which is used in many conventional methods. Then we improve the recent noise detector which uses a non-local search of similar structure. Next we propose a new noise removal algorithm by sparse representation using DCT basis. Furthermore, the sparse representation can remove impulse noise by using the neighboring similar image patch. This method has much more superior noise removal performance than conventional methods at images. We confirm the effectiveness of the proposed method quantitatively and qualitatively.

This paper presents a modulation scheme for impulse radio that uses the first sidelobe for transmitting a non-return-to-zero baseband signal and the implementation of a dual frequency conversion demodulator. The proposed modulation technique realizes two times higher frequency efficiency than that realized by binary phase-shift keying modulation and does not require an up-converter in the transmitter. The dual frequency conversion demodulator compensates for the spectrum distortion caused by the frequency response of the circuits and channel. The effect of frequency compensation is analytically studied. The fabricated demodulator test chip of 65 nm CMOS achieves clock and data recovery at 5.7 Gbps with a power consumption of 24 mW.

In this letter, a novel channel impulse response (CIR)-based fingerprinting positioning method using kernel principal component analysis (KPCA) has been proposed. During the offline phase of the proposed method, a survey is performed to collect all CIRs from access points, and a fingerprint database is constructed, which has vectors including CIR and physical location. During the online phase, KPCA is first employed to solve the nonlinearity and complexity in the CIR-position dependencies and extract the principal nonlinear features in CIRs, and support vector regression is then used to adaptively learn the regress function between the KPCA components and physical locations. In addition, the iterative narrowing-scope step is further used to refine the estimation. The performance comparison shows that the proposed method outperforms the traditional received signal strength based positioning methods.

Performance evaluation of an improved multiband impulse radio ultra-wideband (MIR UWB) system based on sub-band selection is proposed in this paper. In the improved scheme, a data mapping algorithm is introduced to a conventional MIR UWB system, and out of all the sub-bands, only partial ones are selected to transmit information data, which can improve the flexibility of sub-bands/spectrum allocation, avoid interference and provide a variety of data rates. Given diagrams of a transmitter and receiver, the exact bit error rate (BER) of the improved system is derived. A comparison of system performance between the improved MIR UWB system and the conventional MIR UWB system is presented in different channels. Simulation results show that the improved system can achieve the same data rate and better BER performance than the conventional MIR UWB system under additive white Gaussian noise (AWGN), multipath fading and interference coexistence channels. In addition, different data transmission rates and BER performances can be easily achieved by an appropriate choice of system parameters.

In the impulse noise removal from a color image, vector filters are suitable for suppressing false color generation. However, the vector filters do not select optimal vectors to restore noise corrupted pixels. To cope with this problem, a cost function-based vector filter is proposed in this letter.

The notion of multiple constant multiplication (MCM) is extensively adopted in digital signal processing (DSP) applications such as finite impulse filter (FIR) designs. A set of adders is utilized to replace regular multipliers for the multiplications between input data and constant filter coefficients. Though many algorithms have been proposed to reduce the total number of adders in an MCM block for area minimization, they do not consider the actual bitwidth of each adder, which may not estimate the hardware cost well enough. Therefore, in this article we propose a bitwidth-aware MCM optimization algorithm that focuses on minimizing the total number of adder bits rather than the adder count. It first builds a subexpression graph based on the given coefficients, derives a set of constraints for adder bitwidth minimization, and then optimally solves the problem through integer linear programming (ILP). Experimental results show that the proposed algorithm can effectively reduce the required adder bit count and outperforms the existing state-of-the-art techniques.

Tracking capsule endoscope location is one of the promising applications offered by implant body area networks (BANs). When tracking the capsule endoscope location, i.e., continuously localize it, it is effective to take the weighted sum of its past locations to its present location, in other words, to low-pass filter its past locations. Furthermore, creating an exact mathematical model of location transition will improve tracking performance. Therefore, in this paper, we investigate two tracking methods with received signal strength indicator (RSSI)-based localization in order to solve the capsule endoscope location tracking problem. One of the two tracking methods is finite impulse response (FIR) filter-based tracking, which tracks the capsule endoscope location by averaging its past locations. The other one is particle filter-based tracking in order to deal with a nonlinear transition model on the capsule endoscope. However, the particle filter requires that the particle weight is calculated according to its condition (namely, its likelihood value), while the transition model on capsule endoscope location has some model parameters which cannot be estimated from the received wireless signal. Therefore, for the purpose of applying the particle filter to capsule endoscope tracking, this paper makes some modifications in the resampling step of the particle filter algorithm. Our computer simulation results demonstrate that the two tracking methods can improve the performance as compared with the conventional maximum likelihood (ML) localization. Furthermore, we confirm that the particle filter-based tracking outperforms the conventional FIR filter-based tracking by taking the realistic capsule endoscope transition model into consideration.