Despite the appealing advantages of reconfigurable intelligent surfaces (RIS) aided mmWave communications, there remain practical issues that need to be addressed before the large-scale deployment of RISs in future wireless networks. In this study, we jointly consider the non-neglectable practical issues in a multi-RIS-aided mmWave system, which can significantly affect the secrecy performance, including the high computational complexity, imperfect channel state information (CSI), and finite resolution of phase shifters. To solve this non-convex challenging stochastic optimization problem, we propose a robust and low-complexity algorithm to maximize the achievable secrete rate. Specially, by combining the benefits of fractional programming and the stochastic successive convex approximation techniques, we transform the joint optimization problem into some convex ones and solve them sub-optimally. The theoretical analysis and simulation results demonstrate that the proposed algorithms could mitigate the joint negative effects of practical issues and yielded a tradeoff between secure performance and complexity/overhead outperforming non-robust benchmarks, which increases the robustness and flexibility of multiple RIS deployments in future wireless networks.

Analog beamforming with broadband large-scale antenna arrays in millimeter wave (mmWave) multiple input multiple output (MIMO) systems faces the beam squint problem. In this paper, we first investigate the sensitivity of analog beamforming to subarray spatial separations in wideband mmWave systems using hybrid arrays, and propose optimized subarray separations. We then design improved analog beamforming after phase compensation based on Zadoff-Chu (ZC) sequence to flatten the frequency response of radio frequency (RF) equivalent channel. Considering a single-carrier frequency-domain equalization (SC-FDE) scheme at the receiver, we derive low-complexity linear zero-forcing (ZF) and minimum mean squared error (MMSE) equalizers in terms of output signal-to-noise ratio (SNR) after equalization. Simulation results show that the improved analog beamforming can effectively remove frequency-selective deep fading caused by beam squint, and achieve better bit-error-rate performance compared with the conventional analog beamforming.

In this article, a new Beamforming Network (BFN) realized in Broadside Coupled Stripline (BCS) is proposed to feed 1×4 and 2×2 arrays antenna at 28 GHZ-Band. The new BFN is composed only of couplers and phase shifters. It doesn't require any crossover compared to the conventional Butler Matrix (BM) which requires two crossovers. The tight coupling and low loss characteristics of the BCS allow a design of a compact and wideband BFN. The new BFN produces the phase differences of (±90°) and (±45°, ±135°) respectively in x- and y-directions. Its integration with a 1×4 linear array antenna reduces the array area by 70% with an improvement of the gain performance compared with the conventional array. The integration with a 2×2 array allows the realization of a full 2-D beam scanning. The proposed concept has been verified experimentally by measuring the fabricated prototypes of the BFN, the 1-D and 2-D patch arrays antennas. The measured 11.5 dBi and 11.3 dBi maximum gains are realized in θ0 = 14° and (θ0, φ0) = (45°,345°) directions respectively for the 1-D and 2-D patch arrays. The physical area of the fabricated BFN is only (0.37λ0×0.3λ0×0.08λ0), while the 1-D array and 2-D array antennas areas without feeding transmission lines are respectively (0.5λ0×2.15λ0×0.08λ0) and (0.9λ0×0.8λ0×0.08λ0).

Millimeter wave (mmWave) massive Multiple-Input Multiple-Output (MIMO) systems generally adopt hybrid precoding combining digital and analog precoder as an alternative to full digital precoding to reduce RF chains and energy consumption. In order to balance the relationship between spectral efficiency, energy efficiency and hardware complexity, the hybrid-connected system structure should be adopted, and then the solution process of hybrid precoding can be simplified by decomposing the total achievable rate into several sub-rates. However, the singular value decomposition (SVD) incurs high complexity in calculating the optimal unconstrained hybrid precoder for each sub-rate. Therefore, this paper proposes PAST, a low complexity hybrid precoding algorithm based on projection approximate subspace tracking. The optimal unconstrained hybrid precoder of each sub-rate is estimated with the PAST algorithm, which avoids the high complexity process of calculating the left and right singular vectors and singular value matrix by SVD. Simulations demonstrate that PAST matches the spectral efficiency of SVD-based hybrid precoding in full-connected (FC), hybrid-connected (HC) and sub-connected (SC) system structure. Moreover, the superiority of PAST over SVD-based hybrid precoding in terms of complexity and increases with the number of transmitting antennas.

In this paper, millimeter wave (mmWave) filtenna arrays for 5G applications are proposed. Two kinds of 2-element subarrays are designed for horizontal and vertical polarizations. Each subarray consists of three substrate integrated waveguide (SIW) cavities and two sets of stacked patches. Fully-shielded combined eighth-mode SIW (FSD-CEMSIW) cavities are used in the filtenna design. This cavity not only works as the first-stage resonator but also as the power divider for the subarray. As a result, a four-order bandpass filtering response is achieved. Filtenna arrays were fabricated and measured for demonstration. The impedance bandwidths of these subarrays cover 24-30GHz, including the 5G mmWave bands (n257, n258, and n261) with measured average gains of 8.2dBi and more than 22dB out-of-band suppression. The proposed antennas can be good candidates for 5G mmWave communication to reduce the system complexity and potential cost of the mmWave front-ends.

In this paper, a Proof-of-Concept (PoC) architecture is constructed, and the effectiveness of mmWave overlay heterogeneous network (HetNet) with mesh backhaul utilizing route-multiplexing and Multi-access Edge Computing (MEC) utilizing prefetching algorithm is verified by measuring the throughput and the download time of real contents. The architecture can cope with the intensive mobile data traffic since data delivery utilizes multiple backhaul routes based on the mesh topology, i.e. route-multiplexing mechanism. On the other hand, MEC deploys the network edge contents requested in advance by nearby User Equipment (UE) based on pre-registered context information such as location, destination, demand application, etc. to the network edge, which is called prefetching algorithm. Therefore, mmWave access can be fully exploited even with capacity-limited backhaul networks by introducing the proposed algorithm. These technologies solve the problems in conventional mmWave HetNet to reduce mobile data traffic on backhaul networks to cloud networks. In addition, the proposed architecture is realized by introducing wireless Software Defined Network (SDN) and Network Function Virtualization (NFV). In our architecture, the network is dynamically controlled via wide-coverage microwave band links by which UE's context information is collected for optimizing the network resources and controlling network infrastructures to establish backhaul routes and MEC servers. In this paper, we develop the hardware equipment and middleware systems, and introduce these algorithms which are used as a driver of IEEE802.11ad and open source software. For 5G and beyond, the architecture integrated in mmWave backhaul, MEC and SDN/NFV will support some scenarios and use cases.

In millimeter wave (mmWave) vehicular communications, multi-hop relay disconnection by line-of-sight (LOS) blockage is a critical problem, particularly in the early diffusion phase of mmWave-available vehicles, where not all vehicles have mmWave communication devices. This paper proposes a distributed position control method to establish long relay paths through road side units (RSUs). This is realized by a scheme via which autonomous vehicles change their relative positions to communicate with each other via LOS paths. Even though vehicles with the proposed method do not use all the information of the environment and do not cooperate with each other, they can decide their action (e.g., lane change and overtaking) and form long relays only using information of their surroundings (e.g., surrounding vehicle positions). The decision-making problem is formulated as a Markov decision process such that autonomous vehicles can learn a practical movement strategy for making long relays by a reinforcement learning (RL) algorithm. This paper designs a learning algorithm based on a sophisticated deep reinforcement learning algorithm, asynchronous advantage actor-critic (A3C), which enables vehicles to learn a complex movement strategy quickly through its deep-neural-network architecture and multi-agent-learning mechanism. Once the strategy is well trained, vehicles can move independently to establish long relays and connect to the RSUs via the relays. Simulation results confirm that the proposed method can increase the relay length and coverage even if the traffic conditions and penetration ratio of mmWave communication devices in the learning and operation phases are different.

Sharing perceptual data (e.g., camera and LiDAR data) with other vehicles enhances the traffic safety of autonomous vehicles because it helps vehicles locate other vehicles and pedestrians in their blind spots. Such safety applications require high throughput and short delay, which cannot be achieved by conventional microwave vehicular communication systems. Therefore, millimeter-wave (mmWave) communications are considered to be a key technology for sharing perceptual data because of their wide bandwidth. One of the challenges of data sharing in mmWave communications is broadcasting because narrow-beam directional antennas are used to obtain high gain. Because many vehicles should share their perceptual data to others within a short time frame in order to enlarge the areas that can be perceived based on shared perceptual data, an efficient scheduling for concurrent transmission that improves spatial reuse is required for perceptual data sharing. This paper proposes a data sharing algorithm that employs a graph-based concurrent transmission scheduling. The proposed algorithm realizes concurrent transmission to improve spatial reuse by designing a rule that is utilized to determine if the two pairs of transmitters and receivers interfere with each other by considering the radio propagation characteristics of narrow-beam antennas. A prioritization method that considers the geographical information in perceptual data is also designed to enlarge perceivable areas in situations where data sharing time is limited and not all data can be shared. Simulation results demonstrate that the proposed algorithm doubles the area of the cooperatively perceivable region compared with a conventional algorithm that does not consider mmWave communications because the proposed algorithm achieves high-throughput transmission by improving spatial reuse. The prioritization also enlarges the perceivable region by a maximum of 20%.

This paper investigates the wireless information surveillance in a suspicious millimeter wave (mmWave) wireless communication system via the spoofing relay based proactive eavesdropping approach. Specifically, the legitimate monitor in the system acts as a relay to simultaneously eavesdrop and send spoofing signals to vary the source transmission rate. To maximize the effective eavesdropping rate, an optimization problem for both hybrid precoding design and power distribution is formulated. Since the problem is fractional and non-convex, we resort to the Dinkelbach method to equivalently reduce the original problem into a series of non-fractional problems, which is still coupling. Afterwards, based on the BCD-type method, the non-fractional problem is reduced to three subproblems with two introduced parameters. Then the GS-PDD-based algorithm is proposed to obtain the optimal solution by alternately optimizing the three subproblems and simultaneously updating the introduced parameters. Numerical results verify the effectiveness and superiority of our proposed scheme.

Densification of mmWave smallcells overlaid on the conventional macro cell is considered to be an essential technology for enhanced mobile broadband services and future IoT applications requiring high data rate e.g. automated driving in 5G communication networks. Taking into account actual measurement mobile traffic data which reveal dynamicity in both time and space, this paper proposes a joint optimization of user association and smallcell base station (BS)'s ON/OFF status. The target is to improve the system's energy efficiency while guaranteeing user's satisfaction measured through e.g. delay tolerance. Numerical analyses are conducted to show the effectiveness of the proposed algorithm against dynamic traffic variation.

A joint deployment of base stations (BSs) and RGB-depth (RGB-D) cameras for camera-assisted millimeter-wave (mmWave) access networks is discussed in this paper. For the deployment of a wide variety of devices in heterogeneous networks, it is crucial to consider the synergistic effects among the different types of nodes. A synergy between mmWave networks and cameras reduces the power consumption of mmWave BSs through sleep control. A purpose of this work is to optimize the number of nodes of each type, to maximize the average achievable rate within the constraint of a predefined total power budget. A stochastic deployment problem is formulated as a submodular optimization problem, by assuming that the deployment of BSs and cameras forms two independent Poisson point processes. An approximate algorithm is presented to solve the deployment problem, and it is proved that a (1-e-1)/2-approximate solution can be obtained for submodular optimization, using a modified greedy algorithm. The numerical results reveal the deployment conditions under which the average achievable rate of the camera-assisted mmWave system is higher than that of a conventional system that does not employ RGB-D cameras.

As the most compelling candidate for 5G, millimeter-wave communication has drawn considerable interest, despite the absence of systematic research on its performance. Therefore, this study investigates millimeter-wave cellular networks and their use of existing frequency reuse schemes and scheduling methods. To evaluate the performance of these networks, we configure a system-level simulator that reflects the eNodeB architecture and frame structure designed to overcome the millimeter-wave frequency characteristics of the Giga Korea Project. Simulations conducted using various combinations of frequency reuse schemes and scheduling methods are described. We found that the best performing radio resource management scheme changes according to the number of user equipment accessing the eNodeB. The results of this study will contribute to performance estimations of the capacity and fairness of cellular-based millimeter-wave communication systems before they are deployed.

To substantially alleviate the human blockage problem in mmWave communications, this paper proposes a proactive handover system based on human blockage prediction using RGB and depth (RGB-D) cameras. The proposed scheme uses RGB-D camera images to estimate the mobility of pedestrians and to predict when blockage will occur. On the basis of this information, the proposed system transfers a mobile station (STA) communicating with one wireless BS (base station) to another BS before human blockage occurs and thus avoids blockage-induced throughput degradation. This paper presents performance modeling of both proactive handover scheme and reactive handover scheme which is based on the received power level. A numerical evaluation reveals conditions under which the proactive handover scheme achieves higher spectral efficiency compared to reactive scheme. In addition, using IEEE 802.11ad-based wireless local area network (WLAN) devices, a testbed for implementing the proposed system is built. The innovative experimental results demonstrate that the proactive handover system can considerably reduce the duration of human blockage-induced degradation of throughput performance relative to the reactive scheme.

This paper proposes two energy-efficient standby mode algorithms in short-range one-to-one 60GHz millimeter-wave (mmWave) communications. Among the many usage scenarios for mmWave radio, file downloading from kiosk terminals or peer-to-peer sync service with portable terminals are of great interest. For these portable terminals, reducing power consumption of standby mode as well as keeping connection setup time short is important. Comparing the power consumption between frame transmission and reception in short-range one-to-one 60GHz mmWave, the power consumed for a frame reception may become larger than that for a frame transmission. The proposed two energy-efficient standby mode algorithms for one-to-one communications assure the connection setup time and take each terminal's different requirement for reduction of its power consumption into consideration. In the proposed algorithms, each terminal accesses asynchronously and operates based on an interval consisting of several sub-intervals. In one proposed algorithm (Prop 1), a terminal transmits a connection request frame (CREQ) once every sub-interval and the other terminal waits for the CREQ during one sub-interval per interval. Thus, Prop 1 reduces the power consumption for CREQ transmission. In the other proposed algorithm (Prop 2), a terminal selects one sub-interval randomly for each interval and transmits CREQs repeatedly during that sub-interval. The other terminal waits for a CREQ during this CREQ transmission period at every sub-interval. Prop 2 saves the power consumption for a CREQ reception. We evaluate the power consumption of standby mode and connection setup time for Prop 1 and Prop 2 by both numerical analysis and computer simulations. We show that the power consumption of the CREQ waiting terminal with the proposed algorithms is more than 10mW lower than that with the conventional algorithm. We also show that our numerical analysis of the proposed algorithms derives the optimum parameters and facilitates system design. Next, we implement Prop 2 in a fully-integrated CMOS transceiver chip-set with antenna, RF/analog, PHY, and MAC for 60GHz proximity wireless communication. This experimental result is the same as the analysis result and it is verified that our proposed standby algorithm works as designed.

The 60GHz millimeter-wave (mmWave) wireless technology is a focus of increasing attention, since its ability to transmit more than Gbps PHY data rate makes it suitable for high-speed, short-range applications such as peer-to-peer synchronization and kiosk terminals. In the case of short-range communication with a range of several tens of centimeters, only terminals present in this communication range will be affect and communication is considered to be on a one-to-one basis. In one-to-one communication, a simpler and more efficient access mechanism is preferable. The ability of current CSMA/CA based MAC, for example MAC of IEEE 802.11 WLAN systems, to achieve high throughput is limited by the low MAC efficiency caused by high signal exchange overhead, such as interframe space (IFS) and acknowledgement. This paper proposes an ACK/NACK mechanism that enhances the throughput in short-range one-to-one communication. The ACK/NACK mechanism uses Negative ACK (NACK) as the acknowledgement policy to reduce the overhead of ACK and the transmitter switches the required acknowledgement policy to ACK based on a switchover threshold. It solves a problem arising from NACK, namely, that NACK has no mechanism for keeping alive. We evaluate the throughput of the ACK/NACK mechanism by both theoretical analysis and computer simulation. The proposed ACK/NACK mechanism is implemented in 65 nm CMOS process (BBIC); we connect this BBIC to a 60 GHz RFIC and exchange frames wirelessly. In this experiment, it is verified that the ACK/NACK mechanism enhances throughput.

This letter considers problems with an efficient link layer multicasting technique in a wireless personal area network environment using a directional antenna. First, we propose an adaptive directional multicast scheme (ADMS) for delay-sensitive applications in mmWave WPAN with directional antenna. Second, the proposed ADMS aims to improve throughput as well as satisfy the application-specific delay requirements. We evaluate the performances of legacy Medium Access Control, Life Centric Approach, and adaptive directional multicast schemes via QualNet 5.0. Our results show that the proposed scheme provides better performance in terms of total network throughput, average transmission time, packet delivery ratio and decodable frame ratio.

This paper presents a high-throughput low-complexity four-parallel Reed-Solomon (RS) decoder for high-rate WPAN systems. Four-parallel processing is used to achieve 12-Gbps data throughput and low hardware complexity. Also, the proposed pipelined folded Degree-Computationless Modified Euclidean (fDCME) algorithm is used to implement the key equation solver (KES) block, which provides low hardware complexity for the RS decoder. The proposed four-parallel RS decoder is implemented 90-nm CMOS technology optimized for a 1.2 V supply voltage. The implementation result shows that the proposed RS decoder can be operated at a clock frequency of 400 MHz and has a data throughput 12.8-Gbps. The proposed four-parallel RS decoder architecture has high data processing rate and low hardware complexity. Therefore it can be applied in the FEC devices for next-generation high-rate WPAN systems with data rate of 10-Gbps and beyond.

This paper proposes a prioritized aggregation method that supports compressed video transmission on millimeter wave wireless personal area network (mmWave WPAN) systems. Frame aggregation is an effective means to improve system efficiency and throughput for wide band systems such as mmWave WPAN. It is required by the applications that the mmWave WPAN systems should provide Gbps or multiGbps transmission capability. The proposed scheme targets not only transmission efficiency but also support of compressed video transmission which currently is very popular. The proposal combines MAC layer aggregation with PHY layer skew modulation to facilitate the video transmission in a way that more important data is better protected. Simulation results show that the average peak signal to noise ratio (PSNR) performance is improved by 5 dB compared to conventional method, while the Gbps transmission requirement is fulfilled.

This letter considers power-controlled transmission from directional antennas in mmWave wireless personal area network (WPAN) systems. The attributes of these systems are studied; these include the number of concurrent transmissions and the power consumption with different system parameters, such as the antenna's beamwidth and radiating efficiency. Numerical results are presented to show that the power controlled transmission enables more concurrent transmissions than the non-power controlled transmission. The results also show that the number of concurrent transmissions increases as the beamwidth and the path loss component become smaller and the antenna's radiating efficiency increases. In addition, the power controlled system generally uses less power than the non-power controlled transmission set up; the overall analysis is verified by simulation.