An adaptive channel access control method for CDMA/PRMA protocol is proposed. The proposed method utilizes a load and backlog based access control. Dynamic optimal channel loads by which the required packet loss probability can be satisfied are obtained. The number of contending terminals is also estimated more accurately, using statistical characteristics of source models. Permission probability is then calculated based on the dynamic optimal channel load and the estimated number of contending terminals such that the mean channel load (the mean number of packets transmitted in each time slot) can be maintained at the optimal channel load. By maintaining the mean channel load at the dynamic optimal channel load, the radio channel can be very effectively utilized, satisfying the required packet loss probability. A backlog based data transmission using a mixed mode of contention and reservation mode is also proposed to reduce redundant contention and corruption. Simulations are carried out in an isolated cell environment and a cellular environment. The simulation results show that the system capacity can be improved significantly by the proposed method compared with the conventional permission control methods.

A key problem under imperfect power control in multimedia DS-CDMA networks is how to guarantee the differentiated outage probabilities of different traffic classes resulted from the uncertainty of received powers. In addition, in order to utilize the scarce wireless resource efficiently, as many users as possible should be admitted into the network while providing guaranteed quality-of-service support for them. In this work, a call admission control scheme, Differentiated Outage Probabilities CAC or DOP-CAC, is proposed to achieve the above goals for imperfectly power-controlled multimedia CDMA networks. Two important features of CDMA systems are considered in our scheme: one is the power multiplexing among bursty traffics and the other is the power allocation scheme employed at the physical layer. The validity and efficiency of DOP-CAC are verified by numerical examples. Two power allocation schemes, Limited Optimal Power Allocation (LOPA) proposed in [3] and Quasi-Optimal Power Allocation (QOPA) we proposed in [6], are considered respectively and compared in the performance evaluation of DOP-CAC. The results show that DOP-CAC achieves much better resource utilization under QOPA than it does under LOPA. By employing QOPA at the physical layer and DOP-CAC at the link layer, our work suggests a high efficiency solution for QoS support of multimedia traffic under imperfect power control environment.

Randomly addressed polling was proposed as a multiple access control protocol for wireless local area networks (LANs). However, the protocol has difficulties in supporting real-time services such as voice transmission. We propose a reservation scheme and make it possible to support real-time services. The scheme is described in detail. Efficiency and average access delay are analyzed.

This paper presents a fuzzy control-based intelligent medium access controller (FiMAC), which optimizes random access control between heterogeneous traffic aiming at more efficient voice/data integrated services in dynamic reservation TDMA-based broadband radio access networks. In order to achieve the design objective, viz. a differentiated quality-of-service (QoS) guarantee for individual service plus maximal system resource utilization, the FiMAC intelligently and independently controls the random access parameters such as the lengths of random access regions dedicated to respective service traffic and the corresponding permission probabilities, frame-by-frame basis. In addition, we have adopted a mobile-assisted random access mechanism where the voice terminal readjusts a global permission probability from the FiMAC, to handle the 'fair access' issue resulting from distributed queueing problems inherent in the access network. Our extensive simulation results indicate that the FiMAC is well coordinated with a mobile-assisted mechanism such that significant improvements are achieved in terms of voice capacity, delay, and fairness over most of the existing MAC schemes for the integrated services.

A new distributed medium access control (MAC) protocol--Soft Reservation Multiple Access with Priority Assignment (SRMA/PA) protocol--is introduced for supporting the integrated services of real-time and non-real-time applications in mobile ad-hoc networks. The SRMA/PA protocol allows the distributed nodes to contend for and reserve time slots with RTS/CTS-like "collision-avoidance" handshake and "soft reservation" mechanism augmented with distributed and dynamic access priority control. The SRMA/PA protocol realizes distributed scheduling for guaranteeing QoS requirements of integrated services and maximizes statistical multiplexing gain. We have demonstrated by simulation studies that the multiplexing gain can be improved significantly without unduly compromising on system complexity. Moreover, we have shown that the proposed back-off mechanism designed for delay-constrained services is useful for further improving utilization of the channel.

At present, in the Intelligent Transport Systems (ITS) field, research continues In-The-Vehicle Communication (ITVC), Inter-Vehicle Communication (IVC), Road-to-Vehicle Communication (RVC), etc. All information communications technology, especially radio-communications technology, was applied. For example, wireless 1394 is used in ITVC, millimeter-wave communication is used in IVC, and Radio on Fiber (ROF) communication technology is used in RVC. However, it is actually very difficult to design for and accommodate all of these systems. This research, to simplify a design, equipment, structure, etc. of ITCV, IVC, and RVC, utilizes a wireless Bluetooth technology system which is the global radio-communications standard which is capturing the spotlight from various fields. In recent years, demand for a radio-communications service which can be used anywhere is increasing. Furthermore, demand for information service by the Internet is also increasing. This paper proposes simulation of Bluetooth wireless communication for ITS field such as ITVC, IVC and RVC system combined to the global Internet connection. Of course, there are many aspects should be thought carefully when the simulation system will be applied to the ITS infrastructures later. On this paper we have been designing the whole system and the evaluation of the simulation have been testing carefully.

In order to realize a future seamless high-speed road-vehicle communication system, we have proposed using code division multiplexing (CDM) radio transmission scheme by using cyclic shifted-and-extended (CSE) codes as spread codes. As the CSE codes are generated by cyclically shifting and extending a conventionally used code, the number of codes generated from a code is limited to the length of the shift interval and the tolerable period of delayed waves also depends on the length. In this paper, based on CSE codes, we propose a method to minimize the length of the shift interval and a cancellation technique with a simple calculation in order to eliminate the interference from delayed waves caused by the reduction of the length of shift interval. The concept and the BER performances in AWGN, two-paths, and multi-path fading environments are described in this paper. As a result, the maximum transmission rate of CSE-based-CDM transmission per one-code using the newly proposed transmission scheme is 3 times as large as that using conventional CSE codes and DQPSK-CDM transmission scheme.

In this paper, we evaluate the average bit error rate (BER) and bits per symbol (BPS) performances of CDMA system employing the adaptive modulation according to the position of mobile station since the performance of CDMA system is highly dependent on user location especially in the downlink, and further we evaluate the overall performance by considering the user distribution at the level of cell. To evaluate the performance of the considered system in the forward link, we derive the distribution of the received signal to noise ratio (SNR) by Mobile Station located at arbitrary cell position with which we investigate the average BER and BPS performances of the common shared channel, one of the downlink channels of beyond IMT-2000 systems such as 1xEV-DO, 1xTEME and HSPDA. As a result, we observe that the CDMA system adopting the adaptive modulation can get about 2.47 bits per symbol at the cell level, while satisfying the required BER performance over all cell area.

Approximately synchronized CDMA (AS-CDMA) can reduce the inter-channel interference in a cell to zero. This property of AS-CDMA is an advantage over the conventional DS-CDMA. However, the inter-cell interference of the AS-CDMA cellular system has not been sufficiently examined previously. Therefore, the synthetic performance of AS-CDMA cellular system also has not been sufficiently clarified previously. Some factors that affect the inter-cell interference of the AS-CDMA cellular system were theoretically examined, and evaluated by using computer simulation. As the result, we found that transmission power control is effective for reducing the inter-cell interference of the AS-CDMA cellular system. In addition, the synthetic performance of AS-CDMA cellular system was clarified for the first time. Consequently, it was also found that the synthetic performance of the AS-CDMA cellular system is higher than that of the conventional DS-CDMA cellular system.

This paper investigates transmission power control for packet transmissions by using code division multiplexing (CDM) in the downlink common (shared) channel of CDMA cellular packet systems and proposes a transmission power control scheme to improve throughput performance and geographical fairness of communication services. In the proposed scheme, downlink transmission power is controlled based on the signal-to-interference ratio predicted at mobile stations. Throughput performance and transmission delay are evaluated under perfect power control conditions. Simulation results show that by using site diversity technique the proposed scheme improves the downlink throughput for light load conditions and geographical fairness for all offered channel loads under both non-fading and fading environments.

This paper studies the optimization of signature waveforms and power allocation for synchronous code-division multiple access (CDMA) systems under the root-mean-square (RMS) bandwidth constraint. The optimization is considered for two types of receivers, namely the conventional matched filter (MF) receiver and the minimum mean-square error (MMSE) receiver. For both cases, the optimization criterion is to maximize the average signal to interference ratios (SIRs) at the receivers' outputs. For a given RMS bandwidth constraint and an arbitrary power allocation scheme, a procedure to obtain the optimal signature waveforms is provided. Based on this procedure, it is then shown that the optimal power allocation is achieved when all the received powers are equal. With the optimal power allocation, solutions for the optimal signature waveforms are presented and discussed in detail. It is also demonstrated that, compared to the previously obtained Welch-bound-equality (WBE) signature waveforms, the proposed signature waveforms can significantly improve the user performance.

Multiple access interferecnce (MAI) is a major factor limiting the performance of direct-sequence code-division multiple access (DS-CDMA) systems. Since the amount of MAI is dependent on the correlation among user signals, one way to reduce it is to reduce such correlation. In mobile multiuser communication, each user experiences a different time-varying channel response. This user-dependent characteristic in channel variation can be exploited to assist the separation of different user signals, in addition to the capability provided by the spreading codes. As the correlation among different user channels are expected to decrease with increase in time span, enhanced decorrelation among different users' signals can be effected by spacing out the chips of one modulated symbol in time. Thus we consider chip-interleaving DS-CDMA (CI-DS-CDMA) in this study. We investigate its performance through theoretical analysis and computer simulation. Employing only a slightly modified rake receiver structure, CI-DS-CDMA is shown to attain significant performance gain over conventional DS-CDMA, in multiple access communication over single- and multi-path fading channels, without complicated multiuser detection. CI-DS-CDMA also has a lower demand for short-term power control than conventional DS-CDMA, especially in one-path Rayleigh fading. Results of the theoretical analysis and the computer simulation agree well with each other.

We propose a new multiple access communication system based on finite field wavelet spread signature (FFWSS). In addition to the function of frequency diversity and multiple access, which are typically provided by traditional spreading codes, the FFWSS spreads data symbols in time, resulting in robustness against frequency selective slow fading. Using the FFWSS to spread a data symbol so that it is overlapped with neighboring symbols, a FFWSS-CDMA system is developed. It is observed that the ratio of the maximum nontrivial value of periodic correlation function to the code length of FFWSS is the same as that of a Sidelnikov sequence. Using RAKE-based receivers, simulation results show that the proposed FFWSS-CDMA system yields lower bit error rate (BER) than conventional DS-CDMA and MT-CDMA systems in multipath fading channels.

This paper compares by computer simulation the achievable throughput performance employing fast packet scheduling algorithms focusing on the throughput of each user in High Speed Downlink Packet Access (HSDPA). Three packet scheduling algorithms are employed: the Maximum carrier-to-interference power ratio (CIR), Proportional Fairness (PF), and Round Robin (RR) methods. The simulation results elucidate that although the Maximum CIR method achieves an aggregated user throughput within a cell higher than that using the PF and RR methods, the PF method is advantageous because it enhances the user throughput for a large number of users with a lower received signal-to-interference power ratio (SIR), who are located outside the normalized distance of 0.6-0.7 from a cell site (this corresponds to the area probability of 50-60% within the cell) compared to the Maximum CIR method. It is also shown that when the PF method is employed, the probability of user throughput of greater than 2 Mbps in the vicinity of the cell site becomes approximately 45% (5%) for L = 1-path (2-path) fading channel, while it is almost 80% (50%) when using the Maximum CIR method. Finally, we show that the average user throughput in a 2-path Rayleigh fading channel is reduced by approximately 30% compared to that in a 1-path channel due to severe multipath interference (MPI) and that the average user throughput is strongly affected by the total traffic produced within a cell, which is directly dependent on the number of users within a cell and the data size per packet call.

This paper proposes a multipath interference canceller (MPIC) employing multipath interference (MPI) replica generation (MIG) utilizing previously transmitted packet combining (PTPC), which is well-suited to incremental redundancy, in order to achieve a peak throughput of nearly 8 Mbps in a multipath fading environment in high-speed downlink packet access (HSDPA). In our scheme, more accurate MPI replica generation is possible by generating MPI replicas utilizing the soft-decision symbol sequence of the previously transmitted packets in addition to that of the latest transmitted packet. Computer simulation results elucidate that the achievable throughput of the MPIC employing MIG-PTPC is increased by approximately 100 kbps and 200 kbps and the required average received signal energy per symbol-to-background noise power spectrum density ratio (E_s/N₀) per antenna at the throughput of 0.8 normalized by the maximum throughput is improved by about 0.3 and 0.7 dB compared to that of the MPIC using the soft-decision symbol sequence after Rake combining of the last transmitted packet both in 2- and 3-path Rayleigh fading channels for QPSK and 16QAM data modulations, respectively. Furthermore, we clarify that the maximum peak throughput using the proposed MPIC with MIG-PTPC coupled with incremental redundancy achieves approximately 7 Mbps and 8 Mbps with 16QAM and 64QAM data modulations in a 2-path Rayleigh fading channel, respectively, within a 5-MHz bandwidth.

In this paper, a hierarchical bit mapping (HBM) scheme suitable for M-level quadrature amplitude modulation (M-QAM) packet transmission is presented. Generally, M-QAM, such as 16QAM or 64QAM, consists of multiple bits with differing bit error-rate quality. Because the packet error rate when using M-QAM is highly dependent on the performance of the "weakest" (poor quality) bits, the throughput of M-QAM packets can dramatically deteriorate especially in a multi-path environment. This paper proposes the use of a bit mapping scheme conceptually similar to hierarchical QAM to improve packet transmission throughput. For 16QAM under this scheme for example, as there are four bits in a 16QAM symbol, four independent packets can be simultaneously transmitted on each of the different bits when HBM is used. In doing so, at least two packets can be transmitted with a high probability of success even under poor transmission conditions, and under good transmission conditions, four packets can potentially be successfully transmitted. An interference cancellation (IC) method is then presented for HBM, with simulation results showing that the combination of HBM with IC results in very good performance. It was also determined that the HBM scheme can be used easily and effectively with hybrid ARQ.

Interference Cancellation (IC) receivers can be used in CDMA cellular systems to improve the capacity. The IC receivers can be divided into two main categories, Single-User Detectors (SUD) and Multi-User Detectors (MUD). They have different characteristics in terms of intra-cell and inter-cell interference cancellation ability. In this paper we propose two new IC receivers that combines the properties of SUD and MUD receivers. The first one is a Serial IC receiver followed by the Normalized Griffiths' algorithm (SING). The second one is an Integrated Serial IC and Normalized Griffiths' algorithm (iSING). We first compare their basic single-cell performance with the conventional RAKE receiver, the Serial IC and the Normalized Griffiths' Algorithm. Next, we examine their multi-cell performance by doing multi-cell link-level simulations. The results show that even though the Serial IC receiver has good single-cell performance, the proposed receivers have as much as 35-40% higher capacity than the Serial IC receiver in the multi-cell case under the ideal conditions assumed in this paper.

In this paper, two types of multi-stage partial parallel interference cancellation (PIC) receivers are considered for multi-rate DS-CDMA system: multi-stage PIC receiver with partial cancellation factors and multi-stage PIC receiver with decision thresholds. Bit error rate (BER) of the multi-stage partial PIC receivers is obtained by simulation in a Rayleigh fading channel. It is shown that the multi-stage partial PIC receivers achieve smaller BER than the matched filter (MF) receiver, multi-stage PIC receiver, group-wise successive interference cancellation (GSIC) receiver, and extended GSIC receiver (EGSIC) for the multi-rate DS-CDMA system in a Rayleigh fading channel.

This paper presents the results of field experiments on the pilot symbol assisted (PSA) coherent multistage interference canceller (COMSIC) receiver in the direct sequence code division multiple access (DS-CDMA) reverse link. The implemented COMSIC receiver comprising three cancellation stages employs PSA channel estimation and replica generation of multiple access interference (MAI) of other users. The experimental results demonstrate that the COMSIC receiver associated with antenna diversity reception and fast transmission power control (TPC) exhibits effectiveness in suppressing severe MAI in actual multipath fading channels. The transmission power of a mobile station (MS) when the COMSIC receiver is employed at a base station (BS) is reduced by approximately 2.0 and 4.0 dB compared to that with the matched filter (MF)-based Rake receiver when the ratios of the target signal energy per bit-to-interference power spectrum density ratio (E_b/I₀) of the desired user to the target user are Δ_target= -6 and -9 dB, respectively. Furthermore, for the COMSIC receiver, the transmission power of a MS at the average bit error rate (BER) of 10^-3 with antenna diversity is decreased by approximately 7.5 and 11 dB compared to that without antenna diversity when the Δ_target values are -6 and -9 dB, respectively.

This paper presents laboratory and field experimental results of the coherent adaptive antenna array diversity (CAAAD) receiver employing receiver antenna-weight generation common to all Rake-combined paths (hereafter path-common weight generation method) in the W-CDMA reverse link, in order to elucidate the suitability of the path-common weight generation method in high-elevation antenna environments such as cellular systems with a macrocell configuration. Laboratory experiments using multipath fading simulators and RF phase shifters elucidate that even when the ratio of the target E_b/I₀ of the desired to interfering users is Δ E_b/I₀=-12 dB, the increase in the average transmit E_b/N₀ employing the CAAAD receiver coupled with fast transmission power control (TPC) using outer-loop control from that for Δ E_b/I₀=0 dB is within only 1.0 dB owing to the accurate beam and null steering associated with fast TPC. Furthermore, field experiments demonstrate that the required transmission power at the average block error rate (BLER) of 10^-2 employing the CAAAD receiver with four antennas is reduced by more than 2 dB compared to that using a four-branch space diversity receiver using maximum ratio combining (MRC) with the fading correlation between antennas of 0 when Δ E_b/I₀=-15 dB and that the loss in the required transmission power of the CAAAD receiver in the same situation as that in a single-user environment is approximately 1 dB. The field experimental results in an actual propagation environment suggest that the CAAAD receiver is effective in suppressing multiple access interference, thus decreasing the required transmission power when the gap in the direction of arrival between the desired user and interfering users is greater than approximately 20 degrees.

This paper proposes a new blind algorithm effective for multiuser detection with an adaptive array antenna. The conventional blind algorithm, known as the Constant Modulus Algorithm (CMA), has two major drawbacks: (i) the convergence speed is not sufficiently fast for usual applications in mobile communications, and (ii) the algorithm is very likely to lock on the path with the largest received power, which means the signal with the second largest power can hardly be extracted. This paper introduces the Recursive Least Squares algorithm for CMA (RLS-CMA) in order to speed the convergence up, and additionally introduces the concept of the orthogonal projection into CMA so as to extract signals with weak power. The proposed CMA with Orthogonal Projection (CMA-OP) sequentially calculates the weight vector of each user under a constraint that the weight vector should be orthogonal to the estimated array response vectors of previously extracted users. Computer simulations demonstrate that the proposed scheme can operate properly in the Rayleigh fading channels under the two-user condition.

Array antennas are employed at the receiver for a variety of purposes such as to combat fading or to reduce co-channel interference. To evaluate the performance of a wireless communications system using antenna arrays it becomes necessary to have spatial channel models that describe the Angle of Arrival (AOA), Time of Arrival (TOA) and the Angle Spread (AS) of the multipath components. Among the most widely used radio propagation models is the single bounce scattering geometric model, where propagation between the transmitting and receiving antennas is assumed to take place via single scattering from an intervening obstacle. Currently, several geometric models are available such as circular and elliptical scattering models, with each model being applicable to a specific environment type. This paper addresses the modeling, simulation and evaluation of the angle spread in smart antenna systems taking into account the Gaussian density model, and proves that the model finds use both in a micro cell as well as in a macro cell environment. Moreover, we show statistics for the angle and time of arrival.

This paper proposes a 2-dimensional linear propagation prediction (LPP) in maximal ratio combining (MRC) transmitter diversity for orthogonal frequency division multiplexing (OFDM) time division multiple access--time division duplex (TDMA/TDD) systems in order to overcome the degradation of the transmission performance due to the fast fading or the TDD duration. In the proposed scheme, the downlink channel condition of each sub-channel is predicted by interpolating the uplink fading fluctuation with both the amplitude and phase, and the predicted downlink channel condition is used for the weighting factor to employ MRC transmitter diversity. Numerical results obtained by the computer simulation show that the proposed 2-dimensional LPP with the second-order Lagrangeis interpolation predicts the downlink channel condition accurately under the fast fading or the long TDD duration. Moreover, in such a condition, the proposed LPP provides far better performance than the conventional 1-dimensional LPP.

This paper proposes a symbol-by-symbol-based multilevel transmit power control (MTPC) scheme for orthogonal frequency division multiplexing (OFDM) based adaptive modulation system (AMS) to achieve high quality broadband wireless transmission for high mobility terminals. In the proposed system, delay profile for each OFDM symbol is estimated by linearly extrapolating previously received delay profile information (DPI) sequence to improve tracking ability of OFDM based AMS with MTPC to the fast fading variation. Moreover, 2-branch reception diversity is applied to reduce dynamic range and variation speed of the multipath fading. Computer simulation confirms that the proposed system is effective in supporting higher mobility terminals with keeping high transmission quality.

This paper proposes a novel synchronization method of jointly estimating symbol frame timing and carrier frequency-offset for Orthogonal Frequency Division Multiplexing (OFDM) signal operating in the burst mode which is usually employed in the wireless LAN communications systems. The proposed method enables a fast and accurate synchronization for the burst mode OFDM signal even under the presence of large frequency-offset, very low C/N and frequency selective fading environments by using only two preamble symbols inserted at the start of every burst frame. This paper presents the various computer simulation results to verify the performance of proposed synchronization methods both for symbol timing and carrier frequency.

The adaptive phase tracking scheme for orthogonal frequency division multiplexing (OFDM) signals can provide superior PER performance in channels with varying phase noise power. It is an effective technique for achieving high-rate and high quality wireless transmission. This paper proposes a new simple adaptive phase tracking scheme for OFDM signals in order to realize high-rate wireless local area networks (LANs). The proposed scheme measures the integrated phase rotation in order to appropriately set the properties of the FIR filter in the phase tracking circuits. This scheme uses the fact that the integrated phase rotation is correlated to the phase noise power. Assuming an RMS delay spread of 100 ns, computer simulations show that the proposed scheme offers superior required E_b/N₀ performance (with regard to the phase noise power) compared to the conventional fixed-tap scheme, where the phase noise to signal power ratios are below -18 dB. It also offers excellent PER performance at the packet length of 1000 bytes unlike the conventional schemes, which suffer degraded PER performance.

This paper proposes an Orthogonal Frequency Division Multiplexing system with Grouping Adaptive Modulation method (GAM-OFDM). The salient feature of the proposed system is to enable the reduction of required transmission bits for adaptive modulation information (AMI) that is required in the demodulation process at the receiver. This paper also proposes an efficient AMI transmission method for the GAM-OFDM system to enable the efficient transmission of AMI bits by using only two preamble symbols, and the Multi-Carrier Spectrum Spreading (MC-SS) technique to achieve the excellent performance of AMI transmission even under severe multi-path fading environments. This paper presents the various computer simulation results to verify the performance of proposed GAM-OFDM system.

This paper proposes a new method to estimate the channel impulse response for Orthogonal Frequency Division Multiplexing (OFDM) mobile radio transmission. The method employs the Recursive Least Squares (RLS) algorithm so as to exploit the correlations in frequency and time domains, and can improve the estimation accuracy. It is also applicable to both the regular and scattered pilot schemes. Computer simulations demonstrate effectiveness of the method applied to the scattered pilot scheme.

OFDM transmission performance in mobile communications suffers severe degradation caused by multipath delay difference greater than the Guard Interval (GI). This is because the excess delay results in considerable Inter-Symbol Interference (ISI) between temporally adjacent symbols and Inter-Carrier Interference (ICI) among subcarriers in the same symbol. This paper proposes a robust OFDM receiver for the scattered pilot OFDM signal that can effectively suppress both ISI and ICI by using two types of equalization and a smoothed FFT-window. In order to verify the performance of the proposed receiver, computer simulations are conducted in accordance with the scattered pilot OFDM signal format of the Digital Terrestrial Television Broadcasting (DTTB). The simulation results demonstrate that the proposed receiver shows much better performance than the conventional receiver in multipath fading environments with the delay difference greater than GI duration.

This paper proposes a space division multiplexed - coded orthogonal frequency division multiplexing (SDM-COFDM) scheme for multi-input multi-output (MIMO) based broadband wireless LANs. The proposed scheme reduces inter-channel interference in SDM transmission with a simple feed-forward canceller which multiplies the received symbols by the estimated propagation inverse matrix for each OFDM subcarrier. This paper proposes a new preamble pattern in order to improve power efficiency in the estimation of the propagation matrix. Moreover, the proposed likelihood-weighting scheme, which is based on signal-to-noise power ratio (SNR) of each OFDM subcarrier, improves the error correction performance of soft decision Viterbi decoding. Computer simulation shows that the proposed SDM-COFDM scheme with two transmitting/receiving antennas doubles the transmission rate without increasing the channel bandwidth and achieves almost the same PER performance as the conventional single-channel transmission in frequency selective fading environments. In particular, it achieves more than 100 Mbit/s per 20 MHz by using 64QAM with the coding rate of 3/4.

This paper proposes Variable Spreading Factor-Orthogonal Frequency and Code Division Multiplexing (VSF-OFCDM) as the most promising forward link wireless access method in broadband packet wireless transmission using an approximate 50 to 100 MHz bandwidth. The proposed OFCDM employing VSF can flexibly realize near optimum wireless access satisfying higher radio link capacity both in isolated cell environments such as hot-spot areas and indoor offices and in multi-cell environments such as cellular systems by adaptively changing the appropriate spreading factor, SF, in the frequency domain based on the cell structure, radio link conditions such as the delay spread, and major radio link parameters such as the data modulation scheme and channel coding rate. Furthermore, by establishing SF=1, i.e., no spreading mode, VSF-OFCDM can be used as orthogonal frequency division multiplexing (OFDM). Computer simulation results demonstrate that, while SF=1 (OFDM) achieves higher link capacity than SF>1 in an isolated-cell environment, OFCDM with the optimized SF value over 1 achieves approximately 1.4 times higher capacity compared with OFDM in a multi-cell environment associated with the advantageous one-cell frequency reuse. Consequently, VSF-OFCDM can provide seamless deployment of broadband packet wireless access with higher radio link capacity, that is, OFDM in an isolated-cell environment, and OFCDM with the adaptively optimized SF value over 1 in a multi-cell environment according to the major radio link conditions and radio link parameters, by only changing the spreading factor.

This paper presents a performance comparison of the channel-interleaving method in the frequency domain, i.e., bit interleaving after channel encoding, symbol interleaving after data modulation, and chip interleaving after spreading, for Variable Spreading Factor-Orthogonal Frequency and Code Division Multiplexing (VSF-OFCDM) wireless access with frequency domain spreading, in order to reduce the required average received signal energy per symbol-to-background noise power spectrum density ratio (E_s/N₀) and achieve the maximum radio link capacity. Simulation results show that, for QPSK data modulation employing turbo coding with the channel coding rate R=3/4, the chip-interleaving method decreases the required average received E_s/N₀ the most for various radio parameters and propagation model conditions, where the number of code-multiplexing, C_mux, the spreading factor, SF, the r.m.s. delay spread, σ, the number of multipaths, L, and the maximum Doppler frequency, f_D, are varied as parameters. For example, when C_mux=12 of SF=16, the improvement in the required average received E_s/N₀ from the case without interleaving at the average packet error rate (PER) of 10^-2, is approximately 0.3, 0.3, and 1.4 dB for the bit, symbol, and chip interleaving, respectively, in a L=12-path exponential decayed Rayleigh fading channel with σ of 0.043 µsec and f_D of 20 Hz. This is because the chip interleaving obtains a higher diversity gain by replacing the chip assignment over the entire bandwidth. Meanwhile, in 16QAM data modulation with R=1/2, the performance of the chip interleaving is deteriorated, when C_mux/SF>0.25, due to the inter-code interference caused by different fading variations over the spreading duration since the successive chips during the spreading duration are interleaved to the separated sub-carriers. Thus, bit interleaving exhibits the best performance although the difference between bit interleaving and symbol interleaving is slight. Consequently, we conclude that the bit-interleaving method is the best among the three interleaving methods for reducing the required received E_s/N₀ considering the tradeoff between the randomization effect of burst errors and the mitigation of inter-code interference assuming the application of adaptive modulation and channel coding scheme in OFCDM employing frequency domain spreading.

This paper proposes an adaptive radio parameter control scheme that utilizes an optimum radio parameter set comprising the maximum number of retransmissions in hybrid automatic repeat request (HARQ) in addition to the data modulation and channel coding scheme (MCS) according to the Quality of Service (QoS) requirements (i.e., the required packet error rate and delay) and propagation conditions such as the delay spread in the forward link of Orthogonal Frequency and Code Division Multiplexing (OFCDM) broadband wireless access. We elucidate by simulation evaluation that most of the optimum MCSs are common regardless of the delay requirement of traffic data, i.e., common between non-real time (NRT) and real-time (RT) class data. Concretely, the three MCSs of QPSK with the coding rate of R=1/2, 16QAM with R=1/2 and 3/4 are optimum ones, although the additional MCS of QPSK with R=1/3 is effective only for the RT class data in the lower received average received signal energy per symbol-to-background noise power density ratio (E_s/N₀) region. Furthermore, application of a much higher MCS set, 16QAM with R=5/6 and 64QAM with R=3/4, in addition to the three common MCSs improves the throughput under much higher E_s/N₀ conditions in a small delay spread environment. The simulation results show that the delay requirement, i.e., the maximum number of retransmissions, in HARQ does not affect the key radio parameter such as MCS, because of informative results such as a smaller number of retransmissions associated with a less-efficient MCS achieves a higher throughput than does using a more highly-efficient MCS allowing a larger number of retransmissions. Consequently, it is concluded that the proposed adaptive radio parameter control according to the QoS requirements substantially results in the selection of the optimum MCS irrespective of the delay requirement except for the extreme case where no retransmissions are allowed and for special propagation channel conditions.

This paper proposes a three-step cell search algorithm that utilizes only the common pilot channel (CPICH) in the forward link and employs spreading by a combination of a cell-specific scrambling code (CSSC) and an orthogonal short code for Orthogonal Frequency and Code Division Multiplexing (OFCDM) broadband packet wireless access. In the proposed cell search algorithm, the OFCDM symbol timing, i.e., Fast Fourier Transform (FFT) window timing, is estimated by detecting the guard interval timing in the first step. Then, in the second step, the frame timing and CSSC group are simultaneously detected by taking the correlation of the CPICH based on the property yielded by shifting the CSSC phase in the frequency domain. Finally, the CSSC within the group is identified in the third step. The most prominent feature of the proposed cell search algorithm is that it does not employ the conventional synchronization channel (SCH), which is exclusively used for the cell search. Computer simulation results elucidate that when the transmission power ratio of the CPICH to one code channel of the traffic channel (TCH) is 12 dB, the proposed cell search method achieves faster cell search time performance compared to the conventional method using the SCH with the transmission power ratio of the SCH to one code channel of the TCH of 6 dB. Furthermore, the results show that it can accomplish the cell search within 1.7 msec at 95% of the locations in a 12-path Rayleigh fading channel with the maximum Doppler frequency of 80 Hz and the r.m.s. delay spread of 0.32 µs.

This paper presents a cell search scheme embedded with carrier frequency synchronization for inter-cell asynchronous orthogonal frequency-division multiplexing code-division multiplexing (OFDM-CDM) systems. Several subcarriers are dedicated to a differentially encoded synchronization channel (SCH). In the other subcarriers, data symbols and pilot symbols are two-dimensionally spread in the time-frequency domain. The cell search scheme consists of a three-stage cell search and a two-stage carrier-frequency synchronization, that is, coarse carrier-frequency acquisition, fast Fourier transform window-timing detection, SCH frame-timing detection, fine carrier-frequency synchronization, and cell-specific scrambling code (CSSC) identification. Simulation demonstrated that this scheme can identify the CSSC with high detection probability while precisely synchronizing the carrier frequency in severe frequency-selective fading channels.

This paper presents a beamspace-time transmit diversity scheme that uses a space-time block code (STBC) and a fixed multi-beam transmit array with low sidelobes for time-domain spreading orthogonal frequency-division multiplexing code-division multiplexing (OFDM-CDM) downlink transmission. The scheme assigns space-time-coded signals to a pair of neighboring beams via closed-loop beam selection. Time-domain spreading provides non-frequency selectivity in each spreading region, which makes it possible for multiple STBCs to share any beam and to be decoded after despreading. Simulation results demonstrated that multiple transmit beams and multiple receive antennas provide large beam gains and/or a high order of diversity gains. In addition, the proposed scheme spatially separates users by beam and thus alleviates multi-user interference.

In a wireless OFDM-CDMA system, the data-modulated symbol of each user is spread over multiple subcarriers in the frequency domain using a given spreading code. For the downlink (base-to-mobile) transmissions, a set of orthogonal spreading codes defined in the frequency domain is used so that different users data can be transmitted using the same set of subcarriers. The frequency selectivity of the radio channel produces the orthogonality destruction. There are several frequency equalization combining techniques to restore orthogonality, i.e., orthogonal restoration combining (ORC), control equalization combining (CEC) that is a variant of ORC, threshold detection combining (TDC), and minimum mean square error combining (MMSEC). The ORC can restore orthogonality among users but produces noise enhancement. However, CEC, TDC, and MMSEC can balance the orthogonality restoration and the noise enhancement. In this paper, we investigate, by means of computer simulation, how the BER performances achievable with ORC, CEC, TDC, and MMSEC are impacted by the propagation parameters (path time delay difference and fading maximum Doppler frequency), number of users, pilot power used for channel estimation, and channel estimation scheme. To acquire a good understanding of ORC, CEC, TDC, and MMSEC, how they differ with respect to the combining weights is discussed. Also, the downlink transmission performances of DS-CDMA and OFDM-CDMA are compared when the same transmission bandwidth is used. How much better performance is achieved with OFDM-CDMA than with DS-CDMA using ideal rake combining is discussed.

It is well known that diversity performance of communication systems using signals with high dimensions in time, frequency and/or spatial domains depends on correlation of the channel characteristics along signal dimensions. On the other hand, it has not been payed due attention how the coherent receiver which combines the signals is greatly affected by the erroneous channel estimation which can undermine the diversity gain. In this paper, assuming that the estimator is given the a priori probability of the channel characteristics, we propose an optimum estimation scheme based on MAP criterion, in an uplink-MC/CDMA system on channels with frequency selective fading, with an array of antennas at the receiver. The MAP estimator effectively takes into account the correlation of the channel characteristics that the conventional estimator neglects. We also propose a signal design in pilot symbol periods that enables the receiver to separately obtain the sufficient statistic for estimating the channel characteristics without MAI. Using computer simulation, we obtained MSE error performances of the proposed estimator compared with the conventional estimator and their effect on BER performances of the diversity combining receiver. It was observed that using the conventional estimator for combining greater number of signals than the effective channel dimension deteriorated the BER performance while using the proposed estimator kept the optimum performance just as the error-free estimator did. Also obtained for MC/CDMA systems are BER performances of the single user matched filter and MMSE receivers using the proposed and the conventional estimators. A considerable improvement of the MMSE performance was achieved owing to the optimum estimator. It remains for the a priori probability of the channel characteristics to be properly assumed and dealt with in sequential estimation.

We study the influence of decoding order on the capacity of multimedia DS-CDMA system employing imperfect successive interference cancellation. We prove that the capacity is maximized by decoding users according to the ascending order of cancellation errors. We also prove that this capacity-optimal decoding order makes total residual interference minimum at the same time.

In this paper, the separate coding scheme is applied to space-time turbo-coded modulations (ST-TuCM). The separate coding for ST-TuCM uses the plural number of component encoders, each of which is a binary turbo encoder in the transmitter. The receiver has component decoders corresponding to the component encoders. The likelihood values derived by the component decoders are employed as a-priori information of transmitted signal from other transmit antennas in iterative demodulation-decoding. Simulation results under the fast Rayleigh fading channel show that separate coding and iterative demodulation-decoding improve the bit error rate performance.

In this article, we present a scattered pilot aided channel estimation and tracking technique for MIMO-OFDM systems. First we extend Li's estimation algorithm to scattered pilot-aided case. Then a scattered pilot-aided tracking scheme is developed to track the time-varying MIMO channel. The algorithms we present reduce the system overhead and channel estimation complexity to a low level with acceptable performance degradation. Simulations of a MIMO-OFDM system with four-transmit and four-receive antennas show that the new algorithm has better performance than Li's algorithm in time-varying MIMO channels.

Traditional soft-handoff algorithms are based on the static threshold handoff algorithm recommended in the IS-95 standard. They are characterized by two parameters, an add threshold T_add and a drop threshold T_drop. These two parameters are assumed to have some constant values irrespective of the received signal strength of the pilot in the active set. To improve the performance of the soft-handoff, a dynamic threshold concept was proposed in previous work, where T_add and T_drop are dynamically determined according to the received signal strength of the pilot channel in the active set. In this study, previous work of the dynamic threshold algorithm is extended by including additional handoff criteria based on absolute signal strength and/or drop timer. Some functional forms with two new parameters, called boundary thresholds, and slope constant are proposed to dynamically determine T_add and T_drop. The dynamic threshold algorithms are compared with static ones in four different cases. Computer simulations show that the dynamic threshold algorithms outperform the static algorithms. We can see that the performance improvements differ from case to case. For example, when a pure dynamic threshold algorithm is compared with a pure static one (case 1), the decrease in the number of active set is about 13.7%. When the absolute threshold and the drop timer are also included in the handoff decision criteria (case 4), however, the decrease is only about 6.2%.

A great deal of effort has been spent to develop strategies for allocation of resources in DS-CDMA systems in order to mitigate effects of interference between users. Here, the choice of spreading sequences and appropriate power allocation play a crucial role. When developing such strategies, CDMA system designers need to ensure that each user meets its quality-of-service requirement expressed in terms of the signal-to-interference+noise ratio. We say that a set of users is admissible in a CDMA system if one can assign sequences to the users and control their power so that all users meet their quality-of-service requirements. In [1], the problem of admissibility in a synchronous CDMA channel was solved. However, since the simplistic setting of perfect symbol synchronism rarely holds in practice, there is a strong need for investigating asynchronous CDMA channels. In this paper, we consider a K-user asynchronous CDMA channel with processing gain N and identical performance requirements for all users assuming chip synchronism. We solve the problem of admissibility of the users in such a channel if N K, and identify optimal sequences. We also show that constant power allocation is optimal. Results obtained in this paper give valuable insights into the limits of asynchronous CDMA systems.

In this paper, the closed-form expressions of signal-to-interference-plus-noise ratio (SINR) and the outage probability are derived for a maximal ratio combining (MRC) two-dimensional (2-D)-RAKE receiver with imperfect power control in a frequency-selective Nakagami fading channel. The impact of power control error (PCE) on the performance of the receiver is analyzed for all kinds of fading environments. The results of numerical derivation and simulation indicate that the performance of 2-D-RAKE receivers degrades due to imperfect power control. But when PCE is not serious, increasing the number of antennae and temporal diversity order can compensate for the performance loss. The exact performance improvement due to space-time processing varies with the PCE and the fading environment.

In this paper, we present a new design to support multicasting in an ATM switches, called the Singlecast Stuffed Multicast Advanced Processing (SSMAP) ATM switch, which can transmit multicast traffic effectively. The SSMAP ATM switch consists of two cell operation parts, a multicast operation part and a singlecast operation part. This structure is designed so as to increase the efficiency of packet forwarding by allowing singlecast cells to use the resources that remain unused during multicast traffic handling. Furthermore, we propose new multicast scheduling methods using the SSMAP ATM switch. We evaluate the characteristics of the SSMAP ATM switch and multicast scheduling methods by computer simulations, and demonstrate their validity.

Explicit Congestion Notification (ECN) supports the binary congestion information of the network for adjusting the window size. However, this results in the oscillation of the window size and the queue length due to the insufficient congestion information. In this paper, we propose the window-based congestion control mechanism with the modified ECN mechanism. The proposed scheme is based on extracting the network status from the consecutive binary congestion information provided by ECN. From the explicit network information, we estimate the allowable window size to achieve better performance. Through the simulations, the effectiveness of the proposed algorithm is shown as compared with the ECN algorithm.

A new optical access system based on the synchronous transfer mode - passive double star system has been developed to provide high-speed LAN-like access. It uses a shared-band method that enables multiple users to efficiently share a single bandwidth of up to 10 Mb/s and a grouping function that divides the access network into several logical networks, each of which can provide a virtual LAN to users. This paper describes an information model and a framework for configuration management and fault management and discusses the requirements for element management, which involves data-link establishment, logical group management, and testing. Element management mainly requires appropriate remote handling on data cards installed in each optical network unit on user premises. A method is proposed that satisfies these requirements. With this method, the element operations system can provide the required operational functionality.

The adaptive base station antenna is an attractive candidate for establishing high-speed and highly-reliable wireless communication systems. From a commercial viewpoint, since the cost and complexity of adaptive antennas depend on the number of elements, optimizing the antenna configuration while considering the propagation environment is necessary to reduce the number of elements. This paper first presents the Angle of Arrival (AOA) characteristics of delayed waves in a street microcell environment, typically used in urban microcell systems. Then the antenna configuration and antenna spacing suitable for the street microcell are investigated utilizing bit error rate (BER) performance simulations using practical delay profiles and AOAs. The effectiveness of bidirectional elements with respect to the BER performance is also investigated. As the results, we found that broadside array with the spacing of 2.5 wavelengths is suitable for adaptive base station antennas for high data-rate wireless systems placed in a street microcell environment. We also found that bidirectional elements alleviate the BER degradation due to the grating lobe of the antenna with wide element spacing without increasing the antenna size.

The Quality of Service (QoS) requirements such as delay and cell loss ratio (CLR) are very stringent for video transmission. These constraints are difficult to meet if high network utilization is desired. Dynamic bandwidth allocation in which video traffic prediction can play an important role is thus needed. In this paper, we suggest to predict the variation of I frames instead of the actual size of I frames, and propose an algorithm that can achieve fast convergence and small prediction error, thus imposing QoS and attaining high network utilization. The performance of the scheme is studied using the renegotiated constant bit rate (RCBR) service model. The overall dynamic bandwidth allocation scheme based on our fast convergent algorithm is shown to be promising, and practically feasible for efficient transmission of real time videos.

Serious BER performance degradation due to finite numeric precision in VLSI implementation of Log-MAP and MAX-Log-MAP decoders where forward state metric is calculated using reverse tracing method, is analyzed, and two methods are proposed to overcome this problem, the loser storing method for MAX-Log-MAP and the periodic storing method for Log-MAP and MAX-Log-MAP. Both methods can reduce memory storage size effectively by half, but with additional circuit overhead. Our VLSI implementation examples show that, compared with original method, both methods give about 15% improvement in area and power consumption with identical BER performance.