This paper presents the basic characteristics of a beam tilting slot antenna element whose forced resonance is realized by reactance loading; its structure complements that of a dipole antenna element. The radiation pattern is tilted using a properly determined driving point position; a single loading reactance is used to obtain the forced resonance without great changes in the tilt angle. Numerical results show that the reactance element needs to be loaded near the driving point in order to obtain the forced resonance of the antenna and the minimum changes in the beam tilt angle at the same time. When the proposed forced resonant beam tilting slot antenna with a 0.8 λ length is driven at -0.2 λ from the center, the main beam tilt angle of 57.7 degrees and the highest power gain of 3.8 dB are obtained. This slot element has a broad bandwidth, unlike the complementary dipole element.
Makoto YAMADA Akisumi TOMOE Takahiro KINOSHITA Osanori KOYAMA Yutaka KATUYAMA Takashi SHIBUYA
We investigate in detail the scattering properties and heating characteristics in various commercially available optical fibers and fiber cables when a bubble train forms in the middle of the fiber as a result of the fiber fuse phenomenon that occurs when a high power signal is launched into the fiber. We found theoretically and experimentally that almost all the optical light is scattered at the top of the bubble train. The scattered light heats UV coated fiber, nylon jacketed silica fiber, fire-retardant jacketed fiber (PVC or FRPE jacketed fiber) and fire-retardant fiber cable (PVC or FRPE fiber cable), to around 100, over 200 and over 600, respectively, and finally the fiber burns and is destroyed at a launched optical power of 3 W. Furthermore, it is confirmed that the combustion does not spread when we use fire retardant jacketed fibers.
Jang Woon BAEK Young Jin NAM Dae-Wha SEO
In this paper, we propose a novel in-network aggregation scheduling scheme for forest fire monitoring in a wireless sensor network. This adaptively configures both the timeout and the collecting period according to the potential level of a fire occurrence. At normal times, the proposed scheme decreases a timeout that is a wait time for packets sent from child nodes and makes the collecting period longer. That reduces the dissipated energy of the sensor node. Conversely, the proposed scheme increases the timeout and makes the collecting period shorter during fire occurrences in order to achieve more accurate data aggregation and early fire detection.
Jin QIAN Dacheng LIU Ye TAO Xiangmin HUANG Yong LI
The propagation of messages among a group of people, which forms opportunistic Disruption Tolerant Networking (DTN), can be modeled as dynamic graph with links joining every two nodes up and down at a stationary speed. As people in DTN might have different probabilities of sending messages to each other, they should be divided into distinct groups with different link generate speed λ and link perish speed µ. In this letter, we focus on the two-group case, and apply Edge-Markovian Dynamic Graphs to present an analysis framework to evaluate the average delay for the information dissemination in DTN. We also give extensive simulation and numerical results revealing the influence of various parameters.
Digital still cameras emerged following the introduction of the Sony Mavica analog prototype camera in 1981. These early cameras produced poor image quality and did not challenge film cameras for overall quality. By 1995 digital still cameras in expensive SLR formats had 6 mega-pixels and produced high quality images (with significant image processing). In 2005 significant improvement in image quality was apparent and lower prices for digital still cameras (DSCs) started a rapid decline in film usage and film camera sells. By 2010 film usage was mostly limited to professionals and the motion picture industry. The rise of DSCs was marked by a “pixel war” where the driving feature of the cameras was the pixel count where even moderate cost, ∼ $120, DSCs would have 14 mega-pixels. The improvement of CMOS technology pushed this trend of lower prices and higher pixel counts. Only the single lens reflex cameras had large sensors and large pixels. The drive for smaller pixels hurt the quality aspects of the final image (sharpness, noise, speed, and exposure latitude). Only today are camera manufactures starting to reverse their course and producing DSCs with larger sensors and pixels. This paper will explore why larger pixels and sensors are key to the future of DSCs.
Keigo IMAI Shoji YUEN Kiyoshi AGUSA
Distributed applications and services have become pervasive in our society due to the widespread use of internet and mobile devices. There are urgent demands to efficiently ensure safety and correctness of such software. A session-type system is a framework to statically check whether communication descriptions conform to certain protocols. They are shown to be effective yet simple enough to fit in harmony with existing programming languages. In the original session type system, the subject reduction property does not hold. This paper establishes a conservative extension of the original session type system with the subject reduction property. Finally, it is also shown that our typing rule properly extends the set of typeable processes.
Ken AKUNE Shouhei KIDERA Tetsuo KIRIMOTO
Ultra-wide band (UWB) pulse radar with high range resolution and dielectric permeability is promising as an internal imaging technique for non-destructive testing or breast cancer detection. Various imaging algorithms for buried objects within a dielectric medium have been proposed, such as aperture synthesis, the time reversal approach and the space-time beamforming algorithm. However, these algorithms mostly require a priori knowledge of the dielectric medium boundary in image focusing, and often suffer from inadequate accuracy to identify the detailed structure of buried targets, such as an edge or specular surface owing to employing the waveform focusing scheme. To overcome these difficulties, this paper proposes an accurate and non-parametric (i.e. using an arbitrary shape without target modeling) imaging algorithm for targets buried in a homogeneous dielectric medium by advancing the RPM (Range Points Migration) algorithm to internal imaging issues, which has been demonstrated to provide an accurate image even for complex-shaped objects in free-space measurement. Numerical simulations, including those for two-dimensional (2-D) and three-dimensional (3-D) cases, verify that the proposed algorithm enhances the imaging accuracy by less than 1/10 of the wavelength and significantly reduces the computational cost by specifying boundary extraction compared with the conventional SAR-based algorithm.
Dong-Yul LEE Geun-Hyuk YANG Chae-Woo LEE
In the IEEE 802.11e standard, a reference scheduler is presented. The reference scheduler uses the same service interval (SI) to poll all stations in a polling list, and uses separate scheduling and admission algorithms. This increases the polling overhead and decreases TXOP utilization. Many papers have attempted to enhance the reference scheduler, but its admission control is similar to reference scheduler. In this paper, we propose a scheduling and admission algorithm that assigns each station an SI close to its maximum SI (MSI). As a result, the proposed algorithm shows higher performance than that of the reference scheduler.
Kazuya HAYASE Hiroshi FUJII Yukihiro BANDOH Hirohisa JOZAWA
Scalable video coding offers efficient video transmission to a variety of display devices over heterogeneous and error-prone networks. Scalable video coding has been strenuously researched in recent years and state-of-the-art international coding with scalability has been standardized as SVC, which is an extension of H.264/AVC. This paper summarizes the recent advanced research that has been done for improving the quality and reducing the complexity of scalable video coding (including SVC), as well as for improving the quality assessment techniques. It is intended to give researchers a critical, technical overview of what is required to develop more efficient scalable video coding in the future.
Osamu SUGIMOTO Sei NAITO Yoshinori HATORI
In this paper, we propose a novel method of measuring the perceived picture quality of H.264 coded video based on parametric analysis of the coded bitstream. The parametric analysis means that the proposed method utilizes only bitstream parameters to evaluate video quality, while it does not have any access to the baseband signal (pixel level information) of the decoded video. The proposed method extracts quantiser-scale, macro block type and transform coefficients from each macroblock. These parameters are used to calculate spatiotemporal image features to reflect the perception of coding artifacts which have a strong relation to the subjective quality. A computer simulation shows that the proposed method can estimate the subjective quality at a correlation coefficient of 0.923 whereas the PSNR metric, which is referred to as a benchmark, correlates the subjective quality at a correlation coefficient of 0.793.
Our research is focused on examining a stereoscopic quality assessment model for stereoscopic images with disparate quality in left and right images for glasses-free stereo vision. In this paper, we examine the objective assessment model of 3-D images, considering the difference in image quality between each view-point generated by the disparity-compensated coding. A overall stereoscopic image quality can be estimated by using only predicted values of left and right 2-D image qualities based on the MPEG-7 descriptor information without using any disparity information. As a result, the stereoscopic still image quality is assessed with high prediction accuracy with correlation coefficient=0.98 and average error=0.17.
Seok-Min CHAE Sung-Hak LEE Hyuk-Ju KWON Kyu-Ik SOHNG
Recently, a new image appearance model, named iCAM06, was developed for High-Dynamic-Range (HDR) image rendering. The dynamic range of a HDR image needs to be mapped onto the range of the output device where it will be displayed, this is called tone reproduction or tone mapping. iCAM06, a representative HDR rendering algorithm also uses tone compression for image reproduction on the dynamic range of output devices. However, iCAM06 causes a white point shift during its tone compression process. Therefore, we propose a compensation method for white point shifts using corrected channel gain. Experiment results show that the proposed method has better performance than iCAM06.
Yuta KAWAMURA Yusuke HORIE Keisuke SANO Hiroya KODAMA Naoki TSUNODA Yuki SHIBUTA Yuki KAWACHI Mitsuho YAMADA
Three-dimensional (3D) movies have become very popular in movie theaters and for home viewing, To date, there has been no report of the effects of the continual vergence eye movement that occurs when viewing 3D movies from the beginning to the end. First, we analyzed the influence of viewing a 3D movie for several hours on vergence eye movement. At the same time, we investigated the influence of long viewing on the human body, using the Simulator Sickness Questionnaire (SSQ) and critical fusion frequency (CFF). It was suggested that the vergence stable time after saccade when viewing a long movie was influenced by the viewing time and that the vergence stable time after saccade depended on the content of the movie. Also the differences were seen in the SSQ and CFF between the movie's beginning and its ending when viewing a 3D movie.
Nikhil JOSHI Adrish BANERJEE Jeong Woo LEE
The convergence behavior of turbo APPM (TAPPM) decoding is analyzed by using a three-dimensional extrinsic information transfer (EXIT) chart and the decoding trajectory. The signal-to-noise ratio (SNR) threshold, below which iterative decoding fails to converge, is predicted by using the 3-D EXIT chart analysis. Bit error rate performances of TAPPM schemes validate the EXIT-chart-based SNR threshold predictions. Outer constituent codes of TAPPM are chosen to show the lowest SNR threshold with the aid of EXIT chart analysis.
In this paper, we propose low complexity channel parameter tracking methods for adaptive OFDM MMSE channel estimation. Even though the MMSE estimation is one of the most accurate channel estimation methods, it requires several channel information including Doppler frequency, RMS (root mean squared) delay spread, and SNR. To implement the MMSE estimation, tracking of such parameters should be preceded. We propose methods to track the above 3 channel parameters. As for Doppler frequency estimation, we propose an extremum method with a parabolic model, which is a key contribution of this paper. We also analyze the computational complexity of the proposed algorithms. Simulations show that the proposed tracking algorithm tracks the parameters well, and performs better than the conventional fixed-parameter algorithm in terms of BER performance. The BER performance of the adaptive MMSE estimation is better than that of a fixed-parameter (robust) MMSE estimator by about 5 dB.
To reduce the cost of fault management in all-optical networks, it is a promising approach to detect the degradation of optical signal quality solely at the terminal points of all-optical monitoring paths. The all-optical monitoring paths must be routed so that all single-link failures can be localized using route information of monitoring paths where signal quality degradation is detected. However, route computation for the all-optical monitoring paths that satisfy the above condition is time consuming. This paper proposes a procedure for deriving the lower bounds of the required number of monitoring paths to localize all single-link failures, and proposes an efficient monitoring path computation method based on the derived lower bounds. The proposed method repeats the route computation for the monitoring paths until feasible routes can be found, while the assumed number of monitoring paths increases, starting from the lower bounds. With the proposed method, the minimum number of monitoring paths with the overall shortest routes can be obtained quickly by solving several small-scale integer linear programming problems when the possible terminal nodes of monitoring paths are arbitrarily given. Thus, the proposed method can minimize the required number of monitors for detecting the degradation of signal quality and the total overhead traffic volume transferred through the monitoring paths.
Chao LIAO Guijin WANG Bei HE Chenbo SHI Yongling SHEN Xinggang LIN
The time efficiency of aerial video stitching is still an open problem due to the huge amount of input frames, which usually results in prohibitive complexities in both image registration and blending. In this paper, we propose an efficient framework aiming to stitch aerial videos in real time. Reasonable distortions are allowed as a tradeoff for acceleration. Instead of searching for globally optimized solutions, we directly refine frame positions with sensor data to compensate for the accumulative error in alignment. A priority scan method is proposed to select pixels within overlapping area into the final panorama for blending, which avoids complicated operations like weighting or averaging on pixels. Experiments show that our method can generate satisfying results at very competitive speed.
Masayuki ABE Noriaki KOGUSHI Kian Siong ANG René HOFSTETTER Kumar MANOJ Louis Nicholas RETNAM Hong WANG Geok Ing NG Chon JIN Dimitris PAVLIDIS
Novel thermopiles based on modulation doped AlGaAs/InGaAs and AlGaN/GaN heterostructures are proposed and developed for the first time, for uncooled infrared FPA (Focal Plane Array) image sensor application. The high responsivity with the high speed response time are designed to 4,900 V/W with 110 µs for AlGaAs/InGaAs, and to 460 V/W with 9 µs for AlGaN/GaN thermopiles, respectively. Based on integrated HEMT-MEMS technology, the AlGaAs/InGaAs 3232 matrix FPAs are fabricated to demonstrate its enhanced performances by black body measurement. The technology presented here demonstrates the potential of this approach for low-cost uncooled infrared FPA image sensor application.
Jun Gyu LEE Zule XU Shoichi MASUI
We propose a methodology of loop design optimization for fourth-order fractional-N phase locked loop (PLL) frequency synthesizers featuring a short settling time of 5 µsec for applications in an active RFID (radio frequency identification) and automobile smart-key systems. To establish the optimized design flow, equations presenting the relationship between the specification and PLL loop parameters in terms of settling time, loop bandwidth, phase margin, and phase noise are summarized. The proposed design flow overcomes the settling time inaccuracy in conventional second-order approximation methods by obtaining the accurate relationship between settling time and loop bandwidth with the MATLAB Control System Toolbox for the fourth-order PLLs. The proposed flow also features the worst-case design by taking account of the process, voltage, and temperature (PVT) variations in loop filter components, and considers the tradeoff between phase noise and area. The three-step optimization process consists of 1) the derivation of the accurate relationship between the settling time and loop bandwidth for various PVT conditions, 2) the derivation of phase noise and area as functions of area-dominant filter capacitance, and 3) the derivation of all PLL loop components values. The optimized design result is compared with circuit simulations using an actually designed fourth-order fractional-N PLL in a 1.8 V 0.18 µm CMOS technology. The error between the design and simulation for the setting time is reduced from 0.63 µsec in the second-order approximation to 0.23 µsec in the fourth-order optimization that proves the validity of the proposed method for the high-speed settling operations.
Chunxiao LIU Guijin WANG Xinggang LIN Liang LI
Person re-identification is challenging due to illumination changes and viewpoint variations in the multi-camera environment. In this paper, we propose a novel spatial pyramid color representation (SPCR) and a local region matching scheme, to explore person appearance for re-identification. SPCR effectively integrates color layout into histogram, forming an informative global feature. Local region matching utilizes region statistics, which is described by covariance feature, to find appearance correspondence locally. Our approach shows robustness to illumination changes and slight viewpoint variations. Experiments on a public dataset demonstrate the performance superiority of our proposal over state-of-the-art methods.